Search Documents

By Gerhard Derge, Arthur H. Grobe, Harold Markus

The high corrosion resistance possessed by tin under most circumstances, combined with its generally satisfactory appearance and useful physical properties, has led to many and varied uses for the metal. These uses have been partly limited by the fact that tin is an expensive metal, therefore many applications have been developed in which tin has been employed in combination with lead, either by coating, as in tin-lined collapsible tubes, or by the formation of alloys containing various proportions of tin-rich and lead-rich phases, as tcrne plate. A detailed knowledge of the corrosion characteristics of the tin-lead couple therefore is of general interest and has become specially important at the present time, when every effort is being made to conserve tin as much as possible. The present study has been limited to carbonate solutions with a pH range from 8.4 to 11.2 so that the results may be related to earlier work on the corrosion of tin and its alloys. 1-3,6 In these papers, the effects of a number of anion and cation additions to these solutions have been observed. Apparatus and Method The electrodes for the corrosion cell were cut from rolled sheet about 1/16 in. thick. The length of all specimens was held constant at 7 in., while the width was varied from M to 2 in. These electrodes were fastened to brass electrode supports, which were attached to rubber stoppers fitting into tall-type one-liter Pyrex beakers that contained the electrolyte. The lead electrodes were prepared from Omaha pig* and the tin was rolled from a slab of Chempur.† After cutting to size, the sheets were polished with No. I emery paper and cleaned with carbon tetrachloride. The edges, back and upper parts of the specimen were coated with a synthetic lacquer, which was supplemented with beeswax for the lead electrodes. The binding posts were coated with beeswax after the electrodes had been clamped. The pH of the electrolyte was controlled by adjusting the ratio of carbonate to bicarbonate. Approximately 600 ml. of electrolyte was used in each beaker. The entire assembly was placed in an oil bath thermostatically adjusted to operate at 30°C. + 0.1". Potentials were measured against a saturated calomel electrode connected to the cell by an agar-agar salt bridge. The carbonate solution used in the salt bridge was the same as that used in the corrosion cell. Currents were measured with a milliam-

Jan 1, 1942

By Harold Markus, Arthur H. Grobe, Gerhard Derge

The high corrosion resistance possessed by tin under most circumstances, combined with its generally satisfactory appearance and useful physical properties, has led to many and varied uses for the metal. These uses have been partly limited by the fact that tin is an expensive metal, therefore many applications have been developed in which tin has been employed in combination with lead, either by coating, as in tin-lined collapsible tubes, or by the formation of alloys containing various proportions of tin-rich and lead-rich phases, as tcrne plate. A detailed knowledge of the corrosion characteristics of the tin-lead couple therefore is of general interest and has become specially important at the present time, when every effort is being made to conserve tin as much as possible. The present study has been limited to carbonate solutions with a pH range from 8.4 to 11.2 so that the results may be related to earlier work on the corrosion of tin and its alloys. 1-3,6 In these papers, the effects of a number of anion and cation additions to these solutions have been observed. Apparatus and Method The electrodes for the corrosion cell were cut from rolled sheet about 1/16 in. thick. The length of all specimens was held constant at 7 in., while the width was varied from M to 2 in. These electrodes were fastened to brass electrode supports, which were attached to rubber stoppers fitting into tall-type one-liter Pyrex beakers that contained the electrolyte. The lead electrodes were prepared from Omaha pig* and the tin was rolled from a slab of Chempur.† After cutting to size, the sheets were polished with No. I emery paper and cleaned with carbon tetrachloride. The edges, back and upper parts of the specimen were coated with a synthetic lacquer, which was supplemented with beeswax for the lead electrodes. The binding posts were coated with beeswax after the electrodes had been clamped. The pH of the electrolyte was controlled by adjusting the ratio of carbonate to bicarbonate. Approximately 600 ml. of electrolyte was used in each beaker. The entire assembly was placed in an oil bath thermostatically adjusted to operate at 30°C. + 0.1". Potentials were measured against a saturated calomel electrode connected to the cell by an agar-agar salt bridge. The carbonate solution used in the salt bridge was the same as that used in the corrosion cell. Currents were measured with a milliam-

Jan 1, 1942

By W. B. Tijmann

Maintaining safe, yet economical, slope geometries in a mining operation is paramount. When design analysis and engineering judgement have dictated conservative and usually more expensive problem solutions, monitoring has often proven to be a valuable method in dealing with potential slope instability. A well planned and executed monitoring program can allow operation at a lower theoretical margin of safety. Monitoring provides a valuable check on design parameters and can measure effects of remedial improvements. Warning of impending failure can often be established well in advance. The monitoring problem situations in civil engineering works and open pit mining are much alike. Instruments used for monitoring in both industries are often the same. In this paper, geotechnical instruments for measuring deformation and groundwater pressure in rock and overburden are discussed with a broad-brush approach. Results obtained over extended time periods are presented in a graphical presentation for a case history. Descriptions of various types of instruments, mostly used to monitor stability of rock slopes, are discussed, and data analysis and approximate costs are presented.

Jan 1, 1983

By Bryan J. Travis, Thomas L. Cook

INTRODUCTION Our growing concern for adequate and secure sources of energy and minerals has stimulated vigorous exploration for new sources, research toward a better understanding of geological processes, and development of new extraction technologies. The need for control, or at least prediction, of subsurface fluid flow is important for many of these technologies for example: primary, secondary and tertiary recovery of oil; ground water and waste management; in-situ fossil energy extraction (oil shale, coal, tar sands); and solution mining of uranium, copper and other minerals. These technologies, especially the last two, are characterized by highly complex systems. A partial list of the physical processes occurring would include flow in porous/fractured media, multi-phase and multi-component flow with heat transport, chemically active fluids and soils, tracers, diffusion and dispersion, fracturing and dissolution. A great deal of understanding of how these processes behave and interact can be obtained from models. MODELS Theoretical models are valuable because they: 1) provide a frame of reference for interpreting results of laboratory and field experiments; 2) once validated by experiments, allow a variety of geometries, injection/production strategies, etc., to be examined (at relatively low cost) for efficiency and stability; 3) can provide guidance to the design of experiments and field operations. Most models are based on the fundamental principles of mass, momentum and energy balance. But from this starting point, many paths can be taken. For example, there is the theory of Payatakes (1973) which concentrates on the microscale dynamics. In this approach, the rock or soil matrix is represented by a complex of characteristic channels (such as periodically constricted smooth tubes). Detail of flow within the characteristic channel is calculated very accurately. A difficulty with this model is that description of a representative channel can require several parameters which may not be easily measured. Also, it is not clear how the channels can be combined practically to model a large scale flow. Another type of model is the "global" one described by Bear (1972). Here, the continuum equations for conservation of mass, momentum and energy are averaged over a distribution of pore channels, resulting in a set of conservation equations in which the small scale structure of the medium is replaced by quantities such as porosity, permeability, dispersion coefficients and tortuosity. This approach allows computation of large scale flows. However, additional constitutive equations are needed which relate averaged quantities such as permeability to observables such as local saturation, particle size distributions, and others. An important difference between models is the way they handle the momentum equation. Payatakes' model solves the full equation. In others, it is replaced by a simpler relation such as Darcy's law (valid for slow flow rates) or by Forchheimer's equation which extends Darcy's law to higher flow rates. These simple relations can nevertheless match a great deal of experimental data (Dullien 1975). The permeability term which appears in Darcy's law and in Forchheimer's expression has been related to other quantities such as porosity and particle surface area. The Kozeny-Carmen equation is a well-known example, valid for some ranges of porosity and particle sizes and for some materials. Several other semi-theoretical, semi-empirical formulations have been devised, none of which are entirely satisfactory. One goal of researchers has been the ability to predict permeability of a porous material from basic measurable quantities such as grain size distributions without recourse to adjustable parameters. This effort has proceeded from consideration of distributions of idealized, non-intersecting channels, to intersecting channels, to consideration of both distributed pore radii and pore neck radii. This last approach has been used successfully to predict permeabilities (ranging over several orders of magnitude) in sandstones (Dullien 1975). Additionally, studies on explicit networks of channels (e.g., Fatt 1956) and percolation theory (e.g., Larson et. al. 1981) have been used to examine interconnectivity effects in porous media with the hope of eventually being able to predict permeability accurately. To be of more than theoretical interest, a model must be compared s controlled laboratory conditions where boundary and initial conditions and relevant material properties can be accurately determined. Also, extraneous forces can be eliminated so that the interactions between processes of interest can be clearly seen and flow models can be vigorously tested. In contrast to the well-defined environment and

Jan 1, 1982

By Robert C. Berggan

The hot-milling process for reconditioning rock-drill bits is not new. It has been employed by a few mines for years and in the past decade it has been widely adopted, as its advantages have become better known. Because of the extensive commercial development in England and Canada of machines to operate on this principle, general acceptance has been largely in the British possessions and until recently has been chiefly in the field of conventional steel. In the past two years there has been a definite trend toward hot-milling of detachable bits in Canada, but only in the past year has any considerable attempt been made to build special machines for this type of work. Generally a machine designed for conventional steel has been used and special holders employed to manipulate the bit. As early as 1934 at least one operator in the United States had adapted hot-milling to conventional steel with a substantial saving in resharpening costs.1 Several other operators have taken it up but there has been no widespread adoption of the method in this country by users of conventional steel. This may be partly explained by the fact that until recently no American manufacturer produced this equipment and operators have been obliged to build their own hot-millers or import them. Several years ago a few machines were built in Seattle, Washington, and operated in some mines in the northwest, but, for reasons not generally known, the effort was abandoned. The Process Hot-milling performs the function of re-dressing the bit at a forging temperature of about 1650°F., by the removal of metal from the flutes with a milling cutter, followed by a similar cut from the bit gauge. Conventional bits are thus treated following the usual forging operation in a sharpener, and usually in the same heat.

Jan 1, 1940

By Robert C. Berggan

The hot-milling process for reconditioning rock-drill bits is not new. It has been employed by a few mines for years and in the past decade it has been widely adopted, as its advantages have become better known. Because of the extensive commercial development in England and Canada of machines to operate on this principle, general acceptance has been largely in the British possessions and until recently has been chiefly in the field of conventional steel. In the past two years there has been a definite trend toward hot-milling of detachable bits in Canada, but only in the past year has any considerable attempt been made to build special machines for this type of work. Generally a machine designed for conventional steel has been used and special holders employed to manipulate the bit. As early as 1934 at least one operator in the United States had adapted hot-milling to conventional steel with a substantial saving in resharpening costs.1 Several other operators have taken it up but there has been no widespread adoption of the method in this country by users of conventional steel. This may be partly explained by the fact that until recently no American manufacturer produced this equipment and operators have been obliged to build their own hot-millers or import them. Several years ago a few machines were built in Seattle, Washington, and operated in some mines in the northwest, but, for reasons not generally known, the effort was abandoned. The Process Hot-milling performs the function of re-dressing the bit at a forging temperature of about 1650°F., by the removal of metal from the flutes with a milling cutter, followed by a similar cut from the bit gauge. Conventional bits are thus treated following the usual forging operation in a sharpener, and usually in the same heat.

Jan 1, 1940

By K. D. Snyder

Barite deposits occur in the Iglesiente-Sulcis district of southwestern Sardinia, an historically important lead-silver-zinc district. Barite, often genetically associated with the base metal deposits, has become an independently important economic commodity. Barite deposition in southwestern Sardinia was related to Caledonian, Hercynian, and Alpine orogenic cycles. A model is presented that relates synsedimentary, karstic, vein, and residual deposits. Synsedimentary deposits are widespread, have common depositional characteristics, and act as sources, along with hydrothermal systems, for other barite deposit types. Caledonian-, Hercynian-, and Alpine-related secondary enrichment processes resulted in residual and karstic deposits that are complex in terms of their geometry and texture, but are more economically important than those of synsedimentary or hydrothermal origin.

Jan 1, 1985

By D. W. Mitchell

INE operators have a choice of several classi- fications of mechanical loaders. Within each classification there are many types and makes available. Table I lists loaders on which manufacturing data as to operating characteristics are available. This paper discusses the conditions met in a mine as they affect these characteristics. It is assumed that management will provide satisfactory engineering, supervision, power, maintenance, loader service within a concentration of workings, and a balanced working cycle served by balanced production equipment. These are factors which affect the optimum operational efficiency of a loader. The conditions which determine loader choice are: Height of Vein—The main limitation to the use of a loading machine is the height to which the vein is mined; i.e. a loader cannot be higher than the place in which it is to work unless rock is taken. Since there are several low vein loaders being developed and successfully applied, this does not appear to be a requisite of an efficient mining operation. The maximum useable height of a loader should be equal to the working seam thickness less a working clearance for travel and operation. A—Working seam thickness = B—Artificial roof support thickness = C—Safe headroom below support = (generally about 6 in.) D—Height of roadway = E—Total of B + C f D =_______________________ A—E = maximum loader height F—Distance from top of roadway to bottom of roof support = G—-Height of loader's coal or ore line (see Table I) = H—Difference between F and G = Size of largest broken particle + a safety factor of 2 to 3 in. H is a loadability factor and is important because the clearance over the top of the conveyor chain to the roof or roof support must be greater than the largest broken particle or else the particle and/or the conveyor chain may be broken. From this standpoint it might be desirable to use a lower height machine even though it may have a smaller capacity, though this is warranted only when increased lump realization offsets lower man-day and machine pro- duction rates. Ivan Given has stated, "Loading should not be handicapped by securing lump only to grind it in the breaker." Width of Working Place—The width of a working place is the greatest width a place may be safely driven. The working place includes not only the face but the roads the loader must tram when mucking out more than one face. The width is limited by the system of placing props with sufficient room between them for the machine runner (about 2 ft). Maximum width of place in which the loader will operate at maximum efficiency is determined by the type of mounting. With track-mounted loaders, maximum width of place is determined by maximum angular swing of the loading head and proximity of track to the face. The use of double track leads to added expense and operational complexities. Several mines that have used double-track systems have found that a substantial saving is made by the use of machines that load out wider places. Trackless loaders may work in rooms of any maximum width. Minimum width of place in which a loader will operate is determined by width of the loader plus a safe movement area for the operator. Often a barodynamic study of the mine will show that either an increase in room width and/or a change in the system of propping may be made by using roof bolting, full or part-width room timbers, removable aluminum I-beams at the face, etc. Increasing the width of a working place will, in general, increase loader operating efficiency by providing more material per fall and by decreasing the preparation and moving time per ton. A change in the system of propping that would increase the minimum width might permit the use of a higher capacity loader with safer working conditions. Proper face tirnbering is necessary to insure safety from roof falls and because the speed of preparation and loading generally increases since the men work with greater assurance and there is less chance of kicking out posts. Maximum Room Length—With the exception of the scraper and the duckbill, the limit to room

Jan 1, 1952

By K. Huessener

This paper attempts a survey of the principles involved in the combustion of blast-furnace gas in boilers and stoves. I do not expect to be able to give much information which is actually new, since the laws and methods of calculation pertaining to this problem are contained in a number of handbooks; but, so far as I am aware, they have nowhere been treated exclusively with reference to this one problem of gas economy. The road which I follow is less that of strictly scientific research than that of the practical engineer, faced by operation problems which require a quick solution by easily accessible means without a prolonged search in scientific handbooks. For this purpose I give a number of tables and diagrams, as well as the results of many years1 practical working experience as combustion engineer, which I trust will prove useful to my readers. HlSTORICAL Considering the tremendous efforts made during the last 15 years to increase the efficiency of all kinds of power plants, it is highly surprising that until a comparatively very recent period, progress in the economical combustion of blast-furnace gas has been so slow, The explanation generally put forth, that fuel has been so cheap that it was hardly worth while to bother about this economy, will not hold good, for the greatest trouble was taken to improve the combustion of coal and to reduce the consumption of steam, The most plausible explanation appears to be the general impression, held as an accepted fact, that gas, especially hot, uncleaned, blast-furnace gas, was not a good boiler fuel. Many managers of high repute had tried unsuccessfully to improve the conditions of its use, and the dictum went forth that efficiencies of over 60 per cent., particularly with high loads, were impossible. This was the situation not only in the United States, with very cheap fuel, but also in Europe, where fuel prices are twice and three times as high.

Jan 1, 1916

By K. E. Gray, M. S. Seth

Equations of elasticity for transversely isotropic, axisymmetric, homogeneous, porous media exhibiting pore fluid pressure were formulated. Using an analogy between thermal and porous body stresses, it was shown that the solution for a transversely isotropic porous body may be obtained by incorporating body forces and the stresses due to a boundary load into the corresponding solution for the thermal stress problem. Equations of elasticity ad the thermal analogy method were used to determine transient horizontal, tangential, and vertical stresses and radial displacement in a semi-infinite cylindrical region when either a constant pressure or a constant rate of flow is maintained at the wellbore. The vertical and tangential displacements are zero from the conditions of the problem. A numerical analysis was made of the solutions obtained by using a digital computer to determine the relative influence of each system variable. Considering rock as a porous body with internal fluid pressure generally gives results significantly different than considering the rock to be nonporous; the directional character of rocks leads to significant differences as compared to results based upon the common assumption of isotropy. Stress gradients are high near the wellbore but die out away from the well. Radial stresses are compressive or neutral, whereas tangential stresses are tensile, neutral or compressive, depending upon the boundary conditions and physical properties of the system Vertical stresses are compressive for an unbounded system. For constant wellbore injection rate, the vertical stress is proportional to the rate of fluid injection and decreases with time, whereas the radial and tangential stresses increase with time. At a given location, the radial displacement generally is very dependent upon time. INTRODUCTION A realistic appraisal of the state of stress in subsurface rock formations would be of considerable interest and use to the petroleum industry. For example, knowing the state of stress in proximity to a wellbore would be of fundamental importance in designing a fracturing operation or, more important, of clearly understanding the conditions necessary to produce rock failure of desired dimensions and geometry. Understanding conditions necessary for rock failure at the wellbore would also be of utility in a preventive sense. For example, borehole stability is an important consideration for many rock formations, and knowledge of the stress state at and near the wellbore under conditions of substantial pressure gradient due to fluid flow would be of great value. When fluid flows through a porous body which is initially at some uniform stress level, the following forces generate stresses at any point in the body. (1) Forces due to nonuniform pressure distribution. With increasing pressure the elements of a body are compressed. Such compression cannot proceed freely in a continuum when the pressure is not uniform throughout, and thus, stresses due to flow of fluid are set up. (2) Pore fluid pressure. This gives rise to normal stresses whose value at any point is the product of areal porosity and the fluid pressure. Although the fluid exerts uniform pressure, the stresses it creates in an anisotropic body may not be the same in all directions since the areal porosity in an anisotropic porous body is a direction-dependent quantity. This consideration leads to the concept of directional porosity. (3) Body Forces. The flow of the moving fluid imparts a force to the rock matrix, the magnitude of which depends upon the pressure

Jan 1, 1969

By A. Donald Kelmers, Forest G. Seeley, B. Zane Egan

INTRODUCTION Coal ash, presently the fifth most abundant of the solid minerals produced in the United States, is expected to become the fourth most abundant by the end of this decade (1). The production of fly ash from the combustion of pulverized coal amounted to a total of 44 million metric tons (Mt) in 1977 and is expected to Increase to 91 Mt by 1985. Coal ash, which results from the Inorganic clay and mineral content of the coal, contains several elements and thus can be considered as a mined and crushed mineral resource rather than a waste material Furthermore, potential problems associated with fly-ash disposal ponds and the leaching of potentially hazardous elements through groundwater infiltration and/or rainfall provide additional incentive for processing fly ash for environ- mental control as well as for the recovery of certain metal values. Fly ash could provide an abundant domestic source of aluminum and several other metals Aluminum is now recovered from bauxite, and over 90% of this ore is imported since domestic sources are limited and cannot meet the U.S. demand There is a close relationship between the aluminum content of fly ash and the domestic consumption of this metal (Table 1).

Jan 1, 1981

By AIME AIME

UNQUESTIONABLY the Coal Division has never had a meeting in which so many outstanding technical papers were presented of immediate practical application to problems of personnel, mining, safety, preparation, combustion, and carbonization. Should there have been those present with the lingering idea that all that was needed for success in the coal industry was a strong back and a weak mind they must have had a rude awakening.

Jan 1, 1942

By H. Eyring, J. W. Fredrickson

Many theories have been advanced to explain the phenomena of elastic and plastic deformation. The object of this report is to present a mechanism for deformation, not radically differing from existing theories, but embodying.certain principles and concepts of these theories. This proposed theory cannot be the complete answer to the age-old problem of deformation but it is believed that it will be a step further in the proper direction. The plastic properties of solids have recently been reviewed by Seitz and Read.' ZenerZ has reviewed and correlated the existing work on the anelasticity of metals. With these and others3'4'5 resent theories of deformation are well-known. Of the many theories now extant, those receiving most attention have been proffered by Griffith,6 Becker,l Smekal,8 Polanyilg Orowanlo and Taylor.'' Although differing quite widely in details, these theories are based more or less on a common principle of flaws or dislocations that exist in the crystal lattice. The effect of stress concentrations surrounding a flaw or crack has been treated most recently by Fisher and Hollomon.12 The various authors differ as to the exact nature of the flaws or dislocations, the causes of their appearance, or the manner in which they initiate slip. All of the theories agree that the number of dislocations increases with progressing deformation. It is universally agreed that the shearing process is not a simple gliding of ideally perfect atomic lattice planes. It is also agreed that the "macroscopic" process of gliding, or slip, is brought about by the spreading of a large number of locally initiated "glide steps" through the whole crystal. The occurrence of these "glide steps" is closely related to the presence of some kind of deviations from the "ideal" lattice structure, even in the undeformed crystal. These deviations are overcome ''one at a time," in a manner of speaking, due to some stress-concentrating effect.13 Proposed Theory Many solids show a continuously increasing deformation if subjected to a constant load of suitable magnitude in an extended range of temperature for a sufficient time. This deformation, or flow, may be said to be due, in general, to the tendency of the atoms or molecules in an elastically stressed body to readjust themselves in such a way that if the deformation were kept constant, a release of stress would take place. If rupture does not occur, this process of relaxation causes the rate of flow to obtain a final constant value, as shown in the curve (Fig I) obtained by Taylor and Quinney.14 In this state the release of stress by relaxation exactly counterbalances the increase due to the elastic strain on the test pieces.

Jan 1, 1949

By J. S. Aronofsky

The first step in a quantitative analysis ot the mechanism of oil displacement by water in a fractured reservoir is usually conceded to be the solution of the differential equation describing the saturation distribution of two immiscible fluids flowing in a porous medium, where the capillary pressure is taken into account. In such a system the production mechanism may consist of displacement of oil both by the flow of water due to natural or artificially imposed pressure gradients and by imbibition, which implies a flow of water not due to external pressure gradients. Owing to the presence of the two oil displacement mechanisms, the mathematical model given by the differential equation intended to describe the system may not properly represent the behavior of the physical system. In fact, in the reservoir the rate of water advance may be very slow, and in the case of a fractured reservoir with a great number of large fractures, the pressure difference determining the flow of water through the matrix may be much less than 1 lb/'psi over lengths of a few feet. In such a case, imbi-bition (the exchange between oil in the matrix and water in the fractures resulting from capillary forces) may become, with time. a significant element of the production mechanism. It occurred Lo the authors, however, that without going into a physical analysis of the process of production, it might be possible by means of simple abstract reasoning to throw some light on the variation of recovery with time under conditions occurring in a highly fractured oil reservoir with rising water table. The object of this paper is to present both the reasoning and its application to a reservoir of the highly fractured type. Specifically, the analysis given here was undertaken to try to explain the increase of recovery (as defined later) with time as observed in this reservoir, without having to assume unlikely variations in the reservoir parameters with depth. This attempt has been successful as will become clear upon comparison of the computed recoveries with the actual field data. ABSTRACT MODEL Let us consider a small volume. of porous matrix saturated with oil at time, t = 0. Let the process of oil displacement by water start at time, t = t,,. At some time, t, the process will have terminated. Then a volume of oil equal to or smaller than the original oil contained in the matrix will have been produced. The first basic assumption that describes the model and guides the forthcoming reasoning is that the oil production from the small volume. dv, is a continuous monotonic function of time and that it converges to a finite limit. Such an assumption is not inconsistent with the results of laboratory waterflood tests as well as with results of imbibition tests where this is, in fact, observed. The second basic assumption is that none of the properties which determine the rate of convergence change sufficiently during the process to affect this rate or the limit. Let it be assumed that the form of the function of time relative to production from the matrix volume. dv, is given by where V,(t) is the volume of oil produced up to that time t. R is the limit toward which the recovery converges, A is a constant giving the rate of convergence, and V,(t) is the volume of oil originally in place in the volume, dv. It should be noted that recovery at time I will be understood here to he It follows that r. tends to R as t tends to infinity. CONSTRUCTION OF RESERVOIR FROM ABSTRACT MODEL Let the reservoir consist of a series of identical blocks of porous matrix stacked vertically and separated by fractures. Let each of these blocks satisfy the conditions of our abstract model. These conditions are: (1) that recovery is a continuous mono-tonic function of time converging to finite limit, and (2) none of the properties that determine the rate of convergence change sufficiently to affect the rate or the limit. Let water be rising in fractures so that oil production from any part of the block starts when the water comes in conLact with it. TOTAL RECOVERY FROM THE RESERVOIR COMPARED TO RECOVERY FROM A SINGLE MODEL ELEMENT As stipulated in Eq. 1, in the case of the abstract model,

By William Romanoff

IN AN ARTICLE on "Recovering Smelter Dust and Oxide," published in the Engineering and Mining Journal (Vol. 131, No. 2), the authors briefly described some dust-recovery equipment and its operation at a secondary-metals brass-smelting and refining plant. A description of our experience in overcoming certain operating difficulties may prove of interest or value to those who are confronted with some of the same problems or who should equip their furnaces with dust-collecting equipment. The dust loss from reverberatory smelting and refining of brass con¬sists largely of zinc, with smaller percentages of lead, tin, and copper in the order named. At the Kramer plant, the fume discharge from the two stacks amounted to 3 to 4 tons of solids per day, making a dense smoke. With dust equipment in operation, the discharge from the stacks is invisible and approximately 2500 lb. of zinc and other metals is recovered daily thereby from each furnace operating.

Jan 1, 1933

By Leslie Burris, J. C. Hesson

The diffusivity of uranium in liquid cadmium has been measured as a function of temperature by the capillary -bath technique. The diffusivity measurements were made at 4509 500°, 575º, and 650°C, over which temperature range the diffusivity of uranium varied from 1.3 to 2.3 x 10-5 sq cm per sec. The diffusivity of uranium in cadmium was less than that predicted by the Einstein-Stokes equation. VERY little information is available on the diffusivity of uranium in liquid metals. Bonillal has reported a single measurement of the diffusivity of uranium in bismuth. Measurement of the diffusivity of uranium in cadmium was undertaken, not only to supply data in an area in which a dearth of information exists, but also because of a need for this physical property measurement in connection with mass transfer studies now underway in the U-Cd system at Argonne National Laboratory. The capillary-bath method used in this work has been successfully used by other workers2"4 to obtain diffusivities in liquid metal systems. Although considerable experimental technique is required to obtain reliable diffusivity measurements, the basic information required is only that of temperature, capillary tube length, the initial and final compositions of the alloy in the capillary tube, and the composition of the bath into which the solute element is diffusing. From these measurements, diffusivities may be calculated using Fick's law. The diffusivity equations are presented in the Appendix. Equations which are often used to predict diffusivities in dilute solutions5 are the Einstein-Stokes equation: D= (kT)/(6pµr) and the Eyring equation: D = (?,kT/?y?zp), where D= diffusivity (sq cm per sec), k = Boltzman's constant, T= temperature ("K), p = viscosity (poises), r = radius of diffusing molecule or species (cm), and A,, Ay, and A, are the diameters of the diffusing molecule in the three axial directions. For round molecules, the Eyring equation gives values which are 37r times larger than the Einstein-Stokes equation. In this work, the experimental values were compared to the Einstein-Stokes equation. Experimental values of diffusivities in liquid metal systems usually lie between those predicted by the Einstein-Stokes and Eyring equations. The viscosity values for cadmium were obtained from the Liquid Metals Handbook.6 EXPERIMENTAL APPARATUS AND PROCEDURE The general procedure employed consisted of rapidly immersing in a molten cadmium bath containing a negligible amount of uranium a capillary

Jan 1, 1963

By W. O. Philbrook. K M Goldman, M. M. Helzel

RADIOACTIVE calcium has been used to learn whether calcium can be detected in iron saturated with carbon after it has been melted under CaO- A12O3- SiO2 slags similar to those used in the iron blast furnace. It was hoped that the radioactive tracer technique might make possible a general study of steelmaking reactions in which calcium or calcium oxide are involved. No calcium could be found in the metal under conditions which were favorable for the reduction of calcium, and it has been concluded that the calcium content of the iron was less than 6 x 10 - pct. Some of the problems encountered have been instructive with regard to pitfalls and limitations of tracer methods. Calcium oxide occurs in almost all iron- and steelmaking slags, and it is essential to the success of all commercial basic steelmaking processes. Calcium alloys are sometimes used in the deoxidation of steel and for the innoculation of gray iron. The element calcium is therefore almost as ubiquitous in the steel industry as are carbon and oxygen, but calcium has been thought to be completely immiscible with iron in both the liquid and the solid states.' It does not seem entirely unreasonable to Suppose, however, that some low concentration of calcium might exist in liquid iron under a basic slag with other conditions being favorable, just as silicon and other elements can be introduced into iron by reduction of their oxides from slags under appropriate circumstances. The radioactive tracer technique offered a more sensitive method than chemical analysis of testing this supposition. The reasons for interest in this investigation were strong enough to justify a recognized risk of failure. On the theoretical side, information on the distribution of calcium between liquid iron and a slag and the rate at which the equilibrium distribution is approached would contribute strongly to the general theory of slag-metal interface reactions. Furthermore, any evidence on the presence of calcium in liquid iron might provide a vital clue to the mechanism of the desulphurization of iron by slags. All of the reactions which have been proposed to explain desulphurization postulate that the sulphur ultimately becomes fixed in the slag as calcium sulphide, but the mechanism by which sulphur

Jan 1, 1951

By Newell G. Alford

At its meeting in the fall of 1937, the Executive Committee of the Coal Division considered the growing scarcity of young engineers entering coal mining with serious intentions. This scarcity was the cause of considerable alarm and a committee consisting of C. T. Hayden, E. A. Holbrook, C. E. Lawall and L. E. Young, with the writer as chairman, was appointed to gather factual data on the current trend. A questionnaire1 was designed and mailed to the heads of the 60 mineral technology schools listed by Prof. W. B. Plank in his article in September 1937.2 Replies were received from 46 institutions, not all from heads of coal-mining courses but all from men that at one time or another have had experience with some kind of coal-mining curricula and know current student impressions. Our committee is indebted to all of these gentlemen for their cooperation. Our committee hoped by this means to quickly reach the root of the trouble and make a set of comprehensive recommendations to the Coal Division for relieving the industry immediately from the growing dearth of youth who yearn for coal-mining careers, but the condition is more serious than at first diagnosed. We must now refer the question back to the Coal Division, with the recommendation that the Division get the industry's permission for still another major operation on its frame of mind. In addition to 10-year statistics on the first pay received by graduates in coal mining and other technical work, we requested enrollment data for 20 years from all schools with either mining engineering or mineral technology curricula. Nine leading questions were also plied, as shown in the Appendix. Every one of the answers was significant and interesting. Fortunately, we encountered positive frankness that was extremely helpful.

Jan 1, 1938

By Newell G. Alford

At its meeting in the fall of 1937, the Executive Committee of the Coal Division considered the growing scarcity of young engineers entering coal mining with serious intentions. This scarcity was the cause of considerable alarm and a committee consisting of C. T. Hayden, E. A. Holbrook, C. E. Lawall and L. E. Young, with the writer as chairman, was appointed to gather factual data on the current trend. A questionnaire1 was designed and mailed to the heads of the 60 mineral technology schools listed by Prof. W. B. Plank in his article in September 1937.2 Replies were received from 46 institutions, not all from heads of coal-mining courses but all from men that at one time or another have had experience with some kind of coal-mining curricula and know current student impressions. Our committee is indebted to all of these gentlemen for their cooperation. Our committee hoped by this means to quickly reach the root of the trouble and make a set of comprehensive recommendations to the Coal Division for relieving the industry immediately from the growing dearth of youth who yearn for coal-mining careers, but the condition is more serious than at first diagnosed. We must now refer the question back to the Coal Division, with the recommendation that the Division get the industry's permission for still another major operation on its frame of mind. In addition to 10-year statistics on the first pay received by graduates in coal mining and other technical work, we requested enrollment data for 20 years from all schools with either mining engineering or mineral technology curricula. Nine leading questions were also plied, as shown in the Appendix. Every one of the answers was significant and interesting. Fortunately, we encountered positive frankness that was extremely helpful.

Jan 1, 1938

By S. C. Herold

Considerable interest has been shown, during recent years, in the possibilities of developing oil fields in the South American Republics, now that the exhaustion of our present fields can be seen in the not very distant future. The demand for fuel 011 and its products has been increasing far more rapidly than our increment of production during the last few years. Increase of consumption has been largely curtailed by the lack of sufficient supply. The main factors that have contributed to our previous neglect of the southern fields have been as follows: (a) Lack of sufficient demand for the product. (b) Competition with producing fields, having large production, low cost, and better geographical position, such as Tampico, Mexico. (c) Greater interest in home fields with ready market at hand. (d) Our ignorance of southern economic and geologic conditions, due to the distance between those areas and our financial centers. (e) Economic conditions in the southern countries, necessitating high costs of exploration and exploitation of the fields. (f) Our lack of understanding of the business methods of the Latin-American. It must be borne in mind that the oil-development work done to the present time in South America has, with one exception,' been undertaken upon lands which possessed direct evidence of oil in seepages or asphaltic deposits, occurring either immediately upon the lands or in their close vicinity. The development of oil fields in South America is therefore in the pioneer stage. It is not at all improbable that "hidden fields" will be uncovered in future work, as has occurred notably in the mid-continental field of this country within recent years. Location The areas grouped as a unit under the title of North Argentine-Bolivian oil field extend in a narrow belt from the north-central part of

Jan 1, 1920