Search Documents

By Walter Craft, John L. Lamont

Adequate hardenability has long been recognized as one of the first requirements for producing desired mechanical properties in a heat-treated steel. Since the introduction of the Jominy end-quench test' and the development of correlative information to expand its use, industry has had an effective measure of hardenability. Prediction and control of the hardenability have been made possible by Grossmann's principle2 for calculating hardenability from chemical composition; and Field's conversiona from depth of half-martensite hardening to Rockwell C hardness has made the relation more quantitative. These developments have facilitated the design of new steels and the control of standard grades to the extent that it has been possible to establish tentative hardenability bands for some of the more commonly used alloy steels.4 As the depth of hardening of the Jominy test specimen is usually measured by Rockwell C hardness, it was considered that it should be possible to predict the hardness by a more direct calculation. It has been found that this can be accomplished by the addition of Rockwell C units proportional to the carbon and alloy content, grain size, and position in the Jominy test specimen. The calculation has been found to be fairly accurate, and because of its additive character is relatively simple to use. In principle the method of calculation is somewhat similar to the expressions developed by Herty, McBride, and Hollen-back,5 Burns, Moore, and Archer,= and Burns and Riege1.l The calculation is started from a base that includes the effects of carbon content and position in the Jominy test speimen. Rockwell C units are added to the base in proportion to the alloy content and grain size. This sum represents the Rockwell C hardness up to the level at which a disproportionate increase of hardness is caused by the formation of martensite, and above this level an increment for martensite hardening is added. The effects of alloys are directly proportional to the amounts present and are independent of each other, the carbon content, and the position in the specimen. Furthermore, the factors for determining the martensite increment are dependcnt only on carbon content and are independent of cooling rate and alloy content. It is this absence of interrelation between the different factors that makes it possible to calculate the hardness and makes the method of calculation consistent with the principle that the character of the hardening reaction is governed primarily by carbon and that alloys exert their effect chiefly through control of the critical cooling rate. The principle of the calculation, and the effects of alloys on the critical cooling rate,

Jan 1, 1947

By John L. Lamont, Walter Craft

Adequate hardenability has long been recognized as one of the first requirements for producing desired mechanical properties in a heat-treated steel. Since the introduction of the Jominy end-quench test' and the development of correlative information to expand its use, industry has had an effective measure of hardenability. Prediction and control of the hardenability have been made possible by Grossmann's principle2 for calculating hardenability from chemical composition; and Field's conversiona from depth of half-martensite hardening to Rockwell C hardness has made the relation more quantitative. These developments have facilitated the design of new steels and the control of standard grades to the extent that it has been possible to establish tentative hardenability bands for some of the more commonly used alloy steels.4 As the depth of hardening of the Jominy test specimen is usually measured by Rockwell C hardness, it was considered that it should be possible to predict the hardness by a more direct calculation. It has been found that this can be accomplished by the addition of Rockwell C units proportional to the carbon and alloy content, grain size, and position in the Jominy test specimen. The calculation has been found to be fairly accurate, and because of its additive character is relatively simple to use. In principle the method of calculation is somewhat similar to the expressions developed by Herty, McBride, and Hollen-back,5 Burns, Moore, and Archer,= and Burns and Riege1.l The calculation is started from a base that includes the effects of carbon content and position in the Jominy test speimen. Rockwell C units are added to the base in proportion to the alloy content and grain size. This sum represents the Rockwell C hardness up to the level at which a disproportionate increase of hardness is caused by the formation of martensite, and above this level an increment for martensite hardening is added. The effects of alloys are directly proportional to the amounts present and are independent of each other, the carbon content, and the position in the specimen. Furthermore, the factors for determining the martensite increment are dependcnt only on carbon content and are independent of cooling rate and alloy content. It is this absence of interrelation between the different factors that makes it possible to calculate the hardness and makes the method of calculation consistent with the principle that the character of the hardening reaction is governed primarily by carbon and that alloys exert their effect chiefly through control of the critical cooling rate. The principle of the calculation, and the effects of alloys on the critical cooling rate,

Jan 1, 1947

By F. L. Holderreed

A choosy in what they would smelt. The furnace charge had to be coarse, and it had to be rich. They discarded fines in excess of about 1/10 the total weight. They wanted 10% copper content and fussed about anything with as low as 5%. They concentrated the copper content of the charge as much as they could by prior selection. They roasted off enough sulfur to further enrich the copper content of the succeeding fall of matte (a melt of cuprous and ferrous sulfides or Cu2S.FeS). Then they desulfurized the iron and fluxed it by carefully adding silica (quartz, not silicates) for a slag of lower density than the cuprous sulfide (Cu2S or white metal). After skimming off the slag, they further desulfurized the white metal by blowing the molten bath with compressed air. The result was blister copper. Yesterday Their techniques and furnaces? Some experimented with mechanically rabbled roasters, but their standard roasting practice was burning coarse sulfide ore in 250-ton heaps. These heaps, approximately 24 x 24 x 6 ft, were burned for about 75 days down to 6-10% sulfur. The turnaround time for a given roasting position was 100 days. Assuming the base was a hearth, the calculated rate of treatment was on the order of 0.004 tpd per sq ft.

Jan 1, 1971

By D. R. Pratt, R. W. Hanks

The method of Caldwell and Babbitt for detennining Bingham plastic rheological constants from engineering pipe flow data has been erroneously used in many previous applications. A reanalysis of extensive pipe flow data from the literature is performed. Critical Reynolds numbers corresponding to the laminar-turbulent transition calculated from these data are found to agree with theoretically calculated values for the entire flow range studied. Similar agreement is found for the authors&apos; own data&apos; for flow of 10 slurries between parallel plates. The Bingham plastic model is shown to be a reliable representation of the flow of non-Newtonian slurries provided it is properly applied. If the Hedstrom number He = pD2 t0/?2 > 104, then the linear approximation method of Caldwell and Babbitt is invalid for pipe flow data obtained in systems of ordinary engineering interest, and the complete nonlinear form of the pipe flow Bingham plastic equation must be used in determining rheological parameters. INTRODUCTION Many materials of engineering interest must be handled and transported as slurries or suspensions of insoluble particulate matter in a Newtonian liquid. These suspensions frequently exhibit non-Newtonian rheological behavior which is reasonably well described by the simple Bingham plastic rheological equation1 Using this particular equation to describe the laminar flow characteristics of slurries was discussed at length by Caldwell and Babbitt2-4 who considered the flow of various clay slurries and sewage sludges. The model has since been used by many others.5-7 More recently the problem of predicting the laminar turbulent transition Reynolds number for Bingham plastic fluids has been treated8 for the case of flow in pipes. This paper points out errors which have existed in the analysis of Bingham plastic flow since the work of Caldwell and Babbitt2-4 and presents a reanalysis of the laminar turbulent transition calculatiod for Bingham plastic flow in pipes. In addition, new data obtained for flow of Bingham plastic slurries between parallel plates, both in laminar flow and in the laminar turbulent transition region, will be presented and compared with the theoretical analysis of laminar turbulent transition for flow between parallel plates. THEORETICAL ANALYSIS PIPE FLOW The mathematical analysisl-4 of laminar flow of a Bingham plastic fluid leads to the following equation. where q = <v>/R is a pseudoshear rate, rw is the wall shear stress Eo = r0/rw, r0 is the yield stress and 1 is the coefficient of rigidity or plastic viscosity from Eq. 1. Caldwell and Babbitt2-4 recognized that the quartic term in Eq. 2 was small compared to the other terms whenever 5, « 1, and that for large values of 7, a plot of Eq. 2 becomes linear. The slope of such a plot with rw as ordinate is 4? and the intercept is (4/3) ro. This approximation is illustrated schematically in Fig. 1. The shaded region between the true curve and the straight-line approximation near the origin represents the contribution of the quartic term. In principle, therefore,

By R. S. McClellan

DURING the last year or so, with higher prices for gold and silver, many old properties in the West have come back to life. Almost every profitable producer in the old days has been considered, and the reasons for its shut-down investigated. If it seems likely that modern ore-finding, mining, and metallurgical methods, and S35 gold can again put the property on a profitable basis, someone can usually be found to back the venture. Methods of rejuvenation vary with the property, of course, but the following outline of what has been done with one group of mines in Idaho is fairly typical and may be suggestive to others. The Golden Chariot gold-silver properties, near Silver City, consist of seven old mines, working a vein system striking north and south, which had a productive length of some 3500 ft. The vein is a quartz-filled fissure with granite walls. Gold occurs in native, and with silver in the form of electrum which is the natural alloy of the two metals. Silver also occurs in a variety of sulfides. From 1064 to 1876, these old properties were worked intensively to an average depth of about 700 ft., through seven shafts which range in

Jan 1, 1934

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of cassiterite and fluorite with oleic acid as collector and with alizarin dyes as modifying agents were studied by means of small-scale, vacuum-flotation tests. Artificial cassiterite was prepared fot these tests by high-temperature methods, especially by crystallization from borax melts. FLOTATION test work on Bolivian tin ores some years ago led to the development of several workable schemes of selective soap flotation, but left unanswered many questions of soap-flotation chemistry.&apos; Accordingly, the study of the activation and soap flotation of quartz just reported? was undertaken as a start toward the elucidation of some of the unanswered questions. The experimental work on quartz flotation consisted primarily of small-scale, vacuum-flotation tests in which activator and collector additions and pH were varied between wide limits. In the work to be described in this paper, the soap flotation of cassiterite and fluorite was studied by the vacuum-flotation technique developed in the previous study of quartz. Using oleic acid as collector, conditions for floating cassiterite and fluorite in the absence of modifying agents were first determined. Then the effects of barium, calcium, and alizarin dyes on the flotation of cassiterite, fluorite, and quartz were studied. Alizarin dyes were chosen for study because of the promise they have shown as selective modifying agents in the flotation of non-sulphide minerals.12,1 Also, they form a family of reagents in which there should be a systematic correlation of chemical properties with composition. As a preliminary to the study of cassiterite flotation, an investigation of the preparation of synthetic cassiterite and X ray studies of natural and synthetic cassiterite were undertaken. Experimental Methods The flotation technique and most of the reagent preparations were described fully in the previous paper.&apos; In addition, for the present work it was necessary to prepare satisfactory stocks of clean cassiterite and fluorite and to obtain samples of alizarin dyes. Cassiterite: High-grade cassiterite from the Netherlands East Indies was crushed, sized, and cleaned

Jan 1, 1951

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of cassiterite and fluorite with oleic acid as collector and with alizarin dyes as modifying agents were studied by means of small-scale, vacuum-flotation tests. Artificial cassiterite was prepared fot these tests by high-temperature methods, especially by crystallization from borax melts. FLOTATION test work on Bolivian tin ores some years ago led to the development of several workable schemes of selective soap flotation, but left unanswered many questions of soap-flotation chemistry.&apos; Accordingly, the study of the activation and soap flotation of quartz just reported? was undertaken as a start toward the elucidation of some of the unanswered questions. The experimental work on quartz flotation consisted primarily of small-scale, vacuum-flotation tests in which activator and collector additions and pH were varied between wide limits. In the work to be described in this paper, the soap flotation of cassiterite and fluorite was studied by the vacuum-flotation technique developed in the previous study of quartz. Using oleic acid as collector, conditions for floating cassiterite and fluorite in the absence of modifying agents were first determined. Then the effects of barium, calcium, and alizarin dyes on the flotation of cassiterite, fluorite, and quartz were studied. Alizarin dyes were chosen for study because of the promise they have shown as selective modifying agents in the flotation of non-sulphide minerals.12,1 Also, they form a family of reagents in which there should be a systematic correlation of chemical properties with composition. As a preliminary to the study of cassiterite flotation, an investigation of the preparation of synthetic cassiterite and X ray studies of natural and synthetic cassiterite were undertaken. Experimental Methods The flotation technique and most of the reagent preparations were described fully in the previous paper.&apos; In addition, for the present work it was necessary to prepare satisfactory stocks of clean cassiterite and fluorite and to obtain samples of alizarin dyes. Cassiterite: High-grade cassiterite from the Netherlands East Indies was crushed, sized, and cleaned

Jan 1, 1951

By J. Chipman, H. R. Larson

The data previously reported for the quantity as a function of oxygen pressure at 1550°C have been used to compute the activities of Fe, FeO, Fe2O3, and COO in slags of the ternary system. Activities of the first three have been obtained also for two quasi-ternaries involving fixed CaO:SiO2 ratios. IN a previous paper1&apos; the authors reported the results of an investigation into the effects of oxygen pressure on the composition of various simple slags analogous to some of those which are found in steel-making practice. The ratio of ferric iron to total iron was studied at 1550°C in iron oxide melts to which lime, magnesia, lime-plus-silica, and other oxides were added. The oxygen pressures involved those of air, carbon dioxide, and carbon dioxide plus carbon monoxide in several proportions. Although very low oxygen pressures could not be used, the slag-metal equilibrium studies of Fetters and Chip-man&apos; permitted extending the results to slags in equilibrium with iron. For the ternary system CaO-FeO-Fe,O, the oxygen pressure-composition relationship has been determined from zero percent lime to lime saturation over an oxygen pressure range from air to that represented by equilibrium with liquid iron. Lime and silica were added to iron oxide in the ratios 0.54, 1.306, and 2.235 to form three quasi-ternary systems which were also studied over the entire region of liquid melts at 1550°C. Ternary Gibbs-Duhem Equation Wagner" has developed a method by which the activities of two components of a ternary system can be calculated if&apos; the activity of the third component is known throughout the composition range being considered. The fundamental form of the Gibbs-Duhem equation for ternary systems is N, d In a, + N2 d In a, + N3 d In a3 — 0. Wagner has developed a usable form of this equation by introducing the term y = N3/(N3 + N1) and rearranging the equation to give (? In a1/?N2)x = -y/(1-N2)2 (? In a2/?y) x2 N2/1-N2 (? In a2/?N2) y To apply this equation to the slag system CaO-FeO-Fe,O,, the activity of one of these components must be known. However, the only activity which is known from the experimental data is the activity or pressure of oxygen in the gas phase with which the slag is in equilibrium. The activity of oxygen in the slag can be defined as the square root of the oxygen pressure. In order to use oxygen as one component, the composition of the slags must be converted to the basis Fe-O-CaO. Oxygen, exclu-sive of that contained in CaO, then becomes com-ponent 2 in Eq. 1, Fe is selected as 1 and CaO as 3. Then y = Ncao/(Ncao + NFe). Eq. 1 then becomes (? In a fe/? Nx) y = -y/(1-No)2 (? In ao/?y) xp - No/ 1- No (? In ao/ O No) y. In order to evaluate Eq. 2, the boundary conditions must be known. The obvious choice of a standard state for iron is to assign slags in equilibrium with iron an activity of one. Then In a,., or log aFe, which is substituted for convenience, is determined by integrating along a line of constant y from the slag in equilibrium with iron to the composition at which log a,, is to be determined. Mathematically this can be expressed as log aFe (Nlog y) = log a&apos;Fe + (? log a Fe/? No) dNo where the primes indicate equilibrium with liquid iron and a&apos;Fe = 1. When Eq. 3 is integrated along a line of constant y, the following is obtained: log a Fe (No, y) = - y No ?/ No ? y ( log ao/(1- No)2) No d No - No/1-No d log ao. Lime-Iron Oxide Slags Iron Activity: The oxygen pressure of lime-iron oxide slags is shown in Fig. 1 as a function of j, de-fined as j = Fe+++/(Fe++ + Fe +++) for various constant mol percentages of lime. The j values at 0 to 60 pct lime were then determined for oxygen pressures of 1, 10-1, etc. to 10-" atm. For purposes of calculation, the line for zero percent lime was extrapolated to

Jan 1, 1955

By J. A. Ede

THE object of the writer is to call attention to a rather unique aggregation of economic products distributed over a line of succeeding formations about 3 mi. long, to be seen within a few miles of La Salle, Ill. Fig. 1 is an ideal section of the stratification exposed and exploited along a distance of 3 1/5 mi. in a southwesterly direction from the quarry of the Utica Hydraulic Cement Co. located near the historic site of Kaskaskia village to the Oglesby, shaft at Oglesby. No attempt has been made to cover the whole field, special mention only being made (with the exception of two places) of the operations found along the course or parallel to the direction assumed in the ideal section. I have used Fig. 2, after J. H. Bent and De Witt Kelly, to locate the relation of the La Salle anticline to the coal mines of this district and to show the operation of No. 1 and 3 mines of the Illinois Zinc Co.

Jan 9, 1919

By Reno H. Sales

Jan 1, 1914

By John Garcia

IN some districts of the bituminous coal field the problem of construct-ing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large. Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton acid Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, 111. All three have water conditions that make it necessary to regularly seal off till worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. As far as the writers know, these three mines are the only ones in the bitu-minous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will he included herein on the Saxton mine than on the others, as the writers are more familiar with it.

Jan 1, 1937

By D. W. Fuerstenau

A detailed study of the residence time distribution in an industrial balling circuit is presented. Using fired recycle pellets as a tracer impulse in each experiment, material was found to pass through the drum under plug flow conditions with a mean residence time of about 20 seconds. The time for a single pass through the entire circuit is about 60 seconds. Approximately three passes are required for fresh feed to report as product. Segregation of the tracer pellets in the system, according to their diameter, was observed and reasons for this are suggested. These results should be of potential use in the modeling and control of ball balling circuits in the iron ore industry.

Jan 1, 1985

By Charles Fulton

EXPERIMENTAL work on the process was begun on a laboratory scale at Cleveland, Ohio, in 1914, and transferred to East St. Louis, Ill. in 1916, where a commercial sized furnace was in technical operation until January, 1918. The essential steps of the process are as follows: Oxidized zinc ore or roasted zinc concentrate is mixed with crushed coke and coal-tar pitch and formed into briquets 9.25 in. (23.5 cm.) in diameter and 21 in. (53 cm.) long in a manner similar to that used in the manufacture of graphite or carbon electrodes, except that much less care and time are required. The composition varies with the nature of the ore; in one case, the composition was 100 parts ore, 70 parts coke, and 18 to 20 parts pitch. These briquets maintain their form and volume during and after the distillation of the zinc. This object is gained by using coke as the matrix and coal-tar pitch as the binder; this pitch becomes coke on heating and unites the ore particle and the original coke particle into a continuous mass. The briquet is an electrical conductor but only to such, a degree that it can be used as a resistor. The size of the ore, as in the present practice of zinc metallurgy, ranges from fine material, such as flotation concentrate, to coarse table and fine jig concentrate. The process is not restricted to any particular kind of ore, but is applicable to pure high-grade ores, ores high in iron, and complex zinc lead ores, since the residue from the distillation is held immovably in place within the briquet. In the case of complex zinc-lead ores, the distillation is conducted with a carefully regulated temperature so that a high percentage of lead is retained in the distilled briquet, which may then be smelted for its lead content. In present zinc smelting practice, the reduction fuel is from 40 to 50 per cent. of the weight of the ore. In the briquet, it is from 60 to 85 per cent. of the ore; but unless the ore is exceptionally high in residue, the distilled briquet

Jan 9, 1919

By Robert F. Mehl

THE gamma-alpha transformation in iron and iron-rich alloys is of such practical and theoretical importance that many papers have been published upon the subject relating to critical temperatures, transforma-tion rates and accompanying property changes. Although crystallo-graphic studies are of less immediate practical usefulness, the opportunities which these offer to furnish data, on the basic atomic movements which characterize the transformation are not to be neglected1. The early work on the crystallography of this transformation has been reviewed in the fourth paper of this series2 since then several important papers have appeared. Our present, knowledge may be briefly summarized as follows. Kurdjumow and Sachs, working with a 1.4 per cent carbon steel3, established the orientation relationships subsisting between the face-cen-tered gamma and the metastable tetragonal lattices in freshly quenched martensite, and between the face-centered gamma and the body-Centered alpha lattices in tampered martensite. The orientation relationship observed in the latter case may be stated in terms of planes and directions observed to lie parallel in the two lattices: { 111 }Y//{110}a [110]Y//[111]a

Jan 1, 1937

By R. D. Irving

THE object of the present paper is to give an outline account of the mineral resources of the State of Wisconsin, so far as they are now known, including both metallic ores and non-metallic useful mineral substances. The only previous publication making any attempt at such an account is one of a popular nature, prepared by the writer for Snyder and Van Vechten&apos;s Historical Atlas of Wisconsin, which was published at Milwaukee in 1878. The data upon which the statements of the following pages are based are chiefly from the

Jan 1, 1880

By James A. Barr

Phosphate rock is a natural rock containing one or more phosphate minerals usually calcium phosphate, of sufficient purity and quantity to permit its use, either directly or after beneficiation in the manufacture of commercial products.1 The principal minerals in phosphate rock have the apatite structure which may be represented by the type formula: Ca10(X2) (PO4)6 where X represents the hydroxyl group (OH), chlorine or fluorine, either singly or collectively. The calcium may be partly replaced by sodium, magnesium, and other positive ions such as manganese, strontium, lead, uranium, cerium, yttrium and other rare earths. The PO4 radical may be partly replaced by small quantities of UO4, AsO4, SiO4, CO3, SO4, or Vo4. A typical commercial rock is usually a calcium phosphate containing 3 to 4 pct fluorine, the major impurities being limonite or other iron oxides, clay, aluminum phosphates and silica as quartz sand. A little vanadium is present in most of the domestic rock deposits (except the Tennessee Brown Rock), according to Jacob, Hill, Marshall and Reynolds! A little uranium occurs in the Florida leached zone, as will be brought out later. The chemical analyses are reported as P205, or tricalcium phosphate Ca3(PO4)2, the latter often designated by the trade name BPL (bone phosphate of lime). Commercial analyses usually report iron and alumina as oxides, lime as CaO and silica or insoluble. Colony3 examined many samples of apatite, staffelite, dahlite and American phosphorites and concluded that all have identical X-ray diffraction patterns. The phosphates in the phosphate rock have very minute crystalline structures. The mineral apatite Ca3(F.Cl) (PO4) 3 is the principal primary source of the element phosphorus, and occurs widely distributed in igneous rocks but rarely in a minable mass. Only about 12 pct of the world production of phosphate rock comes from primary apatites; the remainder is derived from secondary phosphorites. These phosphorites have been formed by the alteration of sediments by solutions containing phosphoric acid. Such solutions have come from the weathering or leaching of igneous rock containing apatite, bone deposits of prehistoric animals, marine life or guano deposits. These phosphorites are mostly alterations of phosphatic limestones. The sedimentary phosphate deposits are of marine origin and may have been enriched by subsequent solution of the more soluble calcium carbonate by waters containing carbon dioxide, by physical concentration by wave action, and by redeposition of the dissolved phosphate ions. Uses of Phosphate Phosphorus is the spark of life and is the structure builder and one of the main elements of plant food (fertilizer). Without phosphorus, life cannot exist. A "complete" plant food[t] in addition to phosphorus compounds contains potash, which acts as a catalyst to convert nutrients to useful forms, nitrogen to supply the growth element and many minor elements. The cycle of supply of phosphorus is from the apatite to solution and soil, absorption of plant life, decay and return to the soil or by animal life feeding on the plants. With insufficient supply of phosphorus in vegetation, life is not prolific. If crops are removed from

Jan 1, 1960

By E. I. Organick, B. H. Golding

A simple correlation is presented for the prediction of saturation pressures in condensate-gas and volatile-oil mixtures. Saturation pressure is related directly to the composition of the mixture with the aid of two generalized composition characteristics, B, the molal average boiling point, and W, the modified weight average equivalent molecular weight. The need for hydrocarbon equilibrium constants is entirely eliminated. Only the values of the two conlposition parameters need be obtained, and these are calculated in a simple and reproducible manner from the stream analysis of the mixture and the ASTM distillation for the heavy ends. The correlation is given .in the form of a set of 14 working charts in which saturation pressures, either retrograde dew points or bubble points, are plotted cs temperature, forming partial phase envelopes for mixtures having discrete values of the composition parameters, B and Wul. A locus of critical states on each chart intersects the partial phase envelopes, distinguishing retrograde dew point pressures from bubble pressures. A comparison Between experimental and predicted saturation pressures reveals that: the probable error of the predicted values, when considering the data as a whole (214 experimental points), is five per cent; for high gasjoil ratio condensate fluids (approximately 40.000 or more cu ft/bbl) the probable error is about 8 per cent. In either case, however, the probable error is comparable with the overall uncertainty of the data from which the correlation is derived. INTRODUCTION There is a present need for a simplified, yet reasonably accurate method for predicting upper phase boundaries of reservoir fluids. In the case of high gas/oil ratio fluids, namely the so-called highly volatile oils and the condensate gases, no simple method, accurate within 5 to 10 per cent, is now available by which bubble point and retrograde dew point pressures may be predicted. In order to calculate the upper phase boundary of a volatile reservoir fluid, using correlations now available, it is necessary to find and employ the proper K-values (equilibrium volatility ratios of the hydrocarbons in that fluid). This process of finding the Proper K-values usually involves a double trial and error computation. Since the K-values are in themselves dependent upon the composition of the fluid, their use in the calculation of a saturation pressure actually represents an unnecessary complication. The correlation described in this paper relates saturation pressure directly to the stream composition, entirely eliminating the need for K-values. The only data required to calculate the Stream composition are obtained from the customary low temperature fractional analyses of separator gas and liquidt and from the ASTM distillation of the c,+ fraction of the separator liquid. A considerable simplification in the procedure for predicting saturation pressures is thereby effected without significant loss in accuracy. BASIS FOR A CORRELATION Empirical relationships between the saturation pressure and the composition of the fluid in question have already been partially explored by one of the authors.V n particular, a relationship between the critical pressure for a hydrocarbon mixture and its composition was developed. The critical pressure is in reality a saturation pressure, as it repregents a limiting case either of a dew point or of a buhhle point pressure for any given mixture. It was found that the critical pressure may be correlated as a function of two generalized composition characteristics or variables. One characteristic expressed a molal average prop-erty, the other a weight average property of the mixture. Specifically, the molal average boiling point (MABP, or B as it

Jan 1, 1952

By H. L. Overton, J. B. Lipson

The concept of sodium single-ion equivalent activity as developed by Gondouin, Tixier and Simard,&apos; was used to determine the filtrate resistivity-activity relationships for 150 laboratory and 49 field drilling muds. With the exception of the native and phosphate high-resistivity muds and the calcium-treated muds, the filtrate resistivity-activity relationships were found to be within 20 per cent of that for pure sodium-chloride solutions. Gondouin, et al,* previously suggested a method of treating the high-resistivity muds in quantitative electrical log analysis. A new treatment is presented which uses the P-alkalinity of the filtrate as a correlating parameter in handling the calcium-treated muds in quantitative electrical log analysis. INTRODUCTION Gondouin, Tixier, and Simard in 1957 introduced new interpretive procedures for analyzing the self-potential curve of electric logging. They re-emphasized the previous work of the Schlumberger brothers, Wyllie and others, and re-defined the activity concept in terms of a number which they termed the effective resistivity. Their procedures are particuarly effective when the connate-water resistivities are less than 0.08 ohm-m or greater than 0.3 ohm-m. For gyp muds where the calcium content is known, a procedure was presented which allows calculation of the connate-water resistivity with improved accuracy. These procedures assume that one of the fluids in the system is a pure sodium-chloride solution, but they are not limited by the assumptions. For the fresh and saline connate waters, for instance, it is assumed that the drilling mud filtrate is a pure sodium-chloride solution. For the gyp mud interpretive procedure, it is assumed that the connate water is a pure sodium-chloride solution. Brown,&apos; on the other hand, has suggested that it would be extremely fortuitous if drilling mud filtrates could all be treated electrochemically as sodium-chloride solutions, and he cites some examples where discrepancies exist. A study has been made of the deviations of sodium single-ion equivalent activities, an of drilling mud filtrates from that of pure sodium-chloride solutions. Drilling fluids in common use on the Texas and Louisiana Gulf Coast and laboratory-controlled muds were investigated. Using a cell patterned after Gondouin, et al, (Fig. I), the equivalent activities were measured. It should be remembered here that the activity measured is merely an index which uses numbers that represent the sodium single-ion equivalent activity a,., of the mud filtrate. The membrane potential developed across the cell was determined with a null-type potentiometer. The resistivities of the solutions were measured by the four-electrode method. The resistivity system was calibrated by using saturated KC1 solution as a standard. Chemical properties of the drilling fluids studied were measured with standard API-approved equipment for the particular property in question. For the activity measurements, two shale discs were chosen to serve as cationic membranes. These two discs were both 1 1/4 in. in diameter and, respectively, 1/4 and 1/8 in. in thickness. The membrane potential, Em, was determined using the shale discs as cationic selective membranes separating two standard sodium-chloride solutions of known mean activity. Then by comparing the constant Km in the following equation, with the theoretical value of — 59 mv at 75OF, the perfection of the membrane was determined. The variation of Km for the two membranes used in this experimental work, as well as one of the many unsuitable membranes, is shown in Fig. 2. The measurement of the activity of mud filtrate involves the balancing of its combined individual activities against a standard solution of known mean activity. At the point where there exists zero potential across the membrane cell, the activity effects may be assumed equal for all practical purposes. The mechanics of making a null reading of this sort requires having a large number of different mean activity solutions. A more practical method involves

By E. Miller, N. Chou, K. Komarek

The solid solubilities of the compounds PbS, PbSe, and PbTe have been determined by equilibrating single crystals with two phase alloys. The solubilities were determined by measuring the Hall coefficient of the equilibrated samples. The observed maximum deviations from stoichiometry on the lead rich and the chalcogen-rich side of the phase fields were: at. pct excess Pb at pct excess S at 850°C; PbSe--4 x 10&apos;" at. pct excess Pb at at. pct excess at 800°C; and PbTe-2.8 x 10 4 at. pct excess Pb at 780°C, 10"1 at. pct excess Te at 720°C. The previously developed theory of retrograde solubility has been expanded to include intrinsic disorder in the compounds, and the experimental results are in agreement with the theory. THE solid solubility limits of intermetallic semiconducting compounds are of considerable interest, since many of these compounds have potential use as thermoelements in thermoelectric devices, as infrared detectors, or in semiconductor devices. The solidus curves of a significant number of these compounds have been reported to be retrograde with the maximum solid solubility occurring between the eu-tectic and the maximum melting temperatures. In a previous paper,&apos; equations were derived which permit calculation of the maximum solid solubility of an AB compound exhibiting retrograde solubility. Derivation of these equations was based on the assumption that the compound is a nondegenerate semiconductor at the temperature under consideration, that the defects were unassociated, and that the vibrational contribution to the entropy of the compound could be evaluated by the Einstein approximation. It was shown that at the temperature of the maximum solid solubility The entropy term ASS is composed of the entropy of formation of the solid stoichiometric compound (AS$)*, and the entropy due to deviations from stoichiometric composition which is the sum of a con-figurational term (aS*), a vibrational term (AS,), and an electronic term (AS,). In the previous paper the positional entropy was evaluated considering the con- N. CHOU, Member AIME, formerly Graduate Student, New York University, N. Y., is with IBM, Yorktown Heights, N. Y. K. L. KOMAREK, Member AIME, formerly with New York University, is Professor, Department of Inorganic Chemistry, University of Vienna, Vienna, Austria. E. MI LLER, Member AIME, formerly with New York University, is Associate Professor of Mechanical Engineering, California State College at Long Beach, Calif. The paper is based on a thesis submitted by N. CHOU to the Graduate Division, School of Engineering and Science, New York University, in partial fulfillment of the requirements for the degree of Doctor of Philosophy in Materials Science. tributions from defects arising from deviations from stoichiometric composition. The derivation is generalized in the appendix to include intrinsic disorder. The electronic entropy term is also recalculated in the appendix. Of the various semiconducting compounds, the solidus curves of Pbs,&apos; and ~b~e,~ have been most extensively studied. The solidus of PbSe has also been determined, but the temperature of maximum solubility has not been accurately established.5129 The present investigation was undertaken to compare the experimental solid solubility data for these systems with the values predicted theoretically. Since the temperature and composition of the maximum solubility of PbSe has not been accurately determined, experimental emphasis was placed on determining the solidus curves for PbSe in the region of maximum solubility, although experiments were also performed on PbS and PbTe at several temperatures. X-ray diffraction studies were also made on carefully prepared powder samples of PbSe to determine the variation of lattice parameter with composition. EXPERIMENTAL PROCEDURE The procedure of Brebrick and Allgaier was employed for determining the solidus data. Monocrystal-

Jan 1, 1970

By Roger L. Brockenbrough

Steels available for mine-shaft applications are discussed, and the use of steel linings for round and rectangular shafts is reviewed. For rectangular shafts, frameworks constructed of square or rectangular steel tubes offer advantages. Also, corrugated steel sheeting provides a suitable alternative to timber lagging for spanning between the main shaft supports. For round shafts, self-supporting cylindrical steel liners, with circumferential stiffeners to prevent collapse, have been used to depths up to 6000 ft. Several large-diameter round shafts have been constructed with a concrete lining and an internal framework: of high-strength low-alloy steel tubes. It is concluded that in any new shaft construction steel designs should be investigated as economical alternatives to designs using other materials.

Jan 1, 1976