Search Documents

By S. F. Frederick, W. A. Bailey

The relationship between microstructure and mechanical properties of cast 356-type aluminum alloys was studied to determine the cause of the variations in properties resulting from differences in solidification rate. It was found that variations in strength are a consequence of variations in ductility and that ductility is inversely proportional to the dendrite cell size. A mechanism is proposed to account for this correlation based on the fracture strain of the inter-dendritic silicon particles and the differential strain across dendrite cell boundaries. IT has long been assumed that permanent mold castings of aluminum are superior to sand castings because of their finer grain structure and reduced porosity.' A systematic variation of static properties was noted during unpublished studies of fatigue-strength variations with solidification rate of A356-T6. Of particular interest was the observation that for a given composition and heat-treatment, both ductility and the ultimate strength increased with higher solidification rate. Because the A1-Si system forms the basis of many alloys used for castings and welding wire, a study was initiated to determine the details of how higher cooling rates improved mechanical properties of these alloys. The results of this study are presented here. EXPERIMENTAL PROCEDURE Specimens were prepared from 356-T6 to supplement the A365-T6 alloy data from earlier studies. This allowed a comparison of behavior of alloys with substantially different strengths but with only small differences in alloy composition. The composition and heat treatment of both alloys are given in Table I. The specimens were cut from a chill plate casting,' which is a 6 by 9-in. plate, 1 in. thick, which has one end heavily chilled, and a large riser at the other so that solidification is essentially unidirectional from the chill end to the riser. Although not measured here, solidification times measured on similar specimens by embedded thermocouples are a few seconds at the chill end and up to 5 min near the riser. Specimens were obtained by cutting slabs from the plate, parallel to the chill; these represented different cooling rates, with essentially the same composition. For the tests, either 0.125 or 0.250-in. thick slabs were cut for standard 2-in. gage length specimens. The thicker specimens were tested to failure at 2000 lb per min while the thinner specimens were tested in an Instron machine at a constant cross-head speed of 0.02 in. per min. These thin specimens were intended for trans- mission electron microscopy. Some thin specimens were tested to failure while the remainder were given various amounts of prestrain. Dendrite cell sizes were measured by the linear intercept method on photomicrographs at either X100 or X50, depending on the cell size. It was assumed that the dendrite cells were outlined by the silicon particles. Determinations were made on two mutually perpendicular planes and an rms average taken. Electron fractographs of representative tensile specimens were made in the conventional manner using the two-stage replica technique.3 Samples for transmission electron microscopy were prepared by chemical milling followed by electropolishing. RESULTS AND DISCUSSION The results of the tensile tests and the dendrite cell-size determinations are given in Figs. 1 and 2. All data show the same trends, namely, a decrease in ultimate strength and elongation with increasing distance from the chill (and solidification time), and a corresponding increase in dendrite cell size. The yield strength remains essentially constant. The constancy of the yield strength was particularly significant since it indicated that variation in the solidification rate does not affect the stress required to initiate plastic flow. By plotting true stress-true strain curves as in Fig. 3, it can be seen that both

Jan 1, 1969

By Harold Rose

THE peak of production from the Appalachian natural gas field was apparently reached about 10 years ago, and the annual production from Pennsylvania, West Virginia and Ohio has now dropped to about two-thirds of the amounts obtained in 1916 and 1917. This .falling off in production has occurred in spite of vigorous efforts and large expenditures by producing companies to maintain or increase their output. The greatly increased costs of development and handling are reflected in the present average value of natural gas at the point of consumption, which value in the three states referred to, has more than doubled in the past 10 years. While it is true that the natural gas production of the United States has increased during recent years, this increase has come from southwestern states, particularly from Oklahoma, California, Louisiana and Texas, which states are now leaders in the production of this valuable but fleeting resource. Pennsylvania, originally the leading state in natural gas production, occupies sixth place in the latest (1924) U. S. Bureau of Mines statistics. West Virginia, which held first place for 15 years, has dropped to third rank, and Ohio is the seventh state in the order of natural gas production. Domestic and industrial demands for gas are constantly increasing everywhere in the United States. These growing demands have accentuated the difficulties in the localities with depleted natural gas supplies, and serious shortages have already occurred during winter months in the Pittsburgh district. Some relief has been obtained by placing restrictions on the industrial use of natural gas, and by increasing the price (which tends to reduce consumption). Yet these are but temporary expedients for checking gas consumption, which fail to solve the problem of adequate future supplies of gas.

Jan 10, 1926

By Michael J. Fiannnaca, Michael M. Easdon

Disseminated epithermal gold metallization occurs within a breccia unit interpreted to be a submarine debris flow. Gold is associated with oxidized pyrite, fluorite, and jasperoidal silica. A minimum of 8 Mt (9 million st) of open-pittable mining reserves will be cyanide heap leached as run-of-mine ore at a rate of 0.9 Mt (1.0 million stpy 1. Careful evaluation of the combined results of successive sampling projects has established the pit plan, minable reserves, and process metallurgy of the operation. The sampling procedure utilized for a given test depended upon geological interpretation as well as the procedures, successes, and failures of previous tests. This paper summarizes the sampling and testing procedures of the development effort in light of the project goals and attendant problems in achieving them.

Jan 1, 1985

By E. Posnjak

IT is rather the general belief that acidified solutions of ferrous salts are readily oxidized when in contact with air, and often elaborate pre-cautions are taken to prevent it. This, however, is not the case and several statements may be found in the literature expressing surprise at the extreme slowness with which oxidation takes place when air or oxygen is bubbled through such a solution. Thus C. Baskerville and R. Stevenson1 "observed with surprise" that no. oxidation apparently took place, as shown by titration with 0.5 N KMnO4, when a stream of air was passed for 3 hr. through an acidified solution of ferrous ammonium sulfate or ferrous sulfate. The same authors state that even the presence of salts such as cobalt, chromium, copper, manganese, etc., which usually act as oxygen carriers, had "no effect upon the oxidation as was observed by, passing air for 3 hr. through solutions of Mohr's salt acidified with sulfuric acid." While this statement will be proved further on to be at least partly incorrect the slowness of the oxidation of ferrous salts alone has been previously established by McBain.2. His investigation also showed that the rate of oxidation increases markedly with an increase in the concentration of ferrous sulfate as well as that of oxygen; the concentration of free acid had a comparatively small influence, which in the case of sulfuric acid was to retard slightly the rate of reaction. More recently R. Thomas and E. T. Williams3 investigated the catalytic effect of nitric oxide on the oxidation of ferrous salts, which had been earlier patented by McCulloch.4 They found that the probable mechanism of the catalytic action was the oscillation of the catalyst between two stages of oxidation and its interaction alternately with the oxygen and the ferrous iron.

Jan 1, 1927

By Beverley S. Randolph

The coal-measures of George's Creek coal-region, in Maryland, lie in a comparatively flat synclinal basin, about 4 miles wide. The dip of the measures is, in places near the edge of the basin, as much as 20 feet in 100. The Pittsburgh seam, known locally as the " Big Vein," is the only seam worked at the present time. Ocean No. 3, one of the large mines of the Consolidation Coal Company, has its opening on the outcrop of the Pittsburgh seam, in a ravine which cuts into this seam to such an extent as to bring this opening to within a mile of the axis of the basin. After working all the coal to the rise of this point, the mine was further developed by extending a slope down the dip of the seam, making such an angle with the line of greatest dip as to give a grade varying from 1 to 10 per cent., down which the empty cars carry a rope from a single-drum winding-engine. The coal was worked from each side of this slope in successive Iifts during its progress. From the top of the slope, for a distance of 4000 feet to the fourth lift, the " make " of water is drained by gravity through a heading into the adjoining mine. Below this point the water was pumped into this same heading, at the fourth lift, from which point, as before mentioned, it flowed by gravity.

Jan 1, 1895

By P. Gobin, J. Perez, P. Peguin

The strain-amplitude- dependent part of the internal friction of alluminum after several ther momechanical treatments has been measured in the I-cycle range and at the ambient temperature. The internal friction in the outer layer of the torsional specimen us stress is computed from the experimental data. The curues obtained are analyzed in tevnzs of u coirzbinntion of AH and p, which aye, respectively, due to the vecersible unpinning from weak pills and to the plastic strain. Considerirlg the notion of thermally activated unpinning and repinning, it is shown that in our experimental conditions tlze dislocation lines acl as in the H model of Granato and Liiclze. It is also seen that the internal friction p which appears at higher- strains call be described by a simple expression which is in good agreement with our results. A qualitative interpretatiorz is proposed by combining these new types of intelpnal fviction. We define the internal friction 6 as half the ratio of the dissipated energy aW during one cycle to the maximum supplied strain energy W of a material submitted to a periodic stress. Experiment and theory show that internal friction varies with stress above a critical value.' Below this value the internal friction is strain-amplitude-independent and is often masked by an experimental background; so we shall call it AB. ~bove this critical value, the internal friction is strain-amplitude-dependent. This quantity is usually called aH:' and it can be explained as a thermal unpinning of dislocations.3-6 Furthermore, at higher stresses, a rapid increase of internal friction appears. This phenomenon could be caused by the plastic strain,' so we shall call it Ap. It seems interesting to us to study the influence of several t her momechanical treatments on the curve internal friction 6 vs strain E, in order to study the variation of AH and p with the concentration and the repartition of linear and point defects. In order to try to explain the results obtained, we shall propose and discuss models for H and hp and shall show that we obtain a combination of these two types of internal friction. 1) EXPERIMENTAL PROCEDURE 1) Preparation and Treatment of Specimens. We

Jan 1, 1968

By E. N. Harshman

The Wind River Formation of Eocene age is the host rock for large high-grade uranium deposits in the Shirley Basin. The major deposits are in a northwest-trending belt of sandstones that were deposited in stream channels and that were lithologically favorable for uranium accumulation. Paleotopography influenced the character and position of the belt. The major deposits within the belt are at, or near, the margins of large tongues of altered sandstone formed in the most transmissive parts of thick sandstone beds. At least two tongues of altered sandstone are present in the belt, one of which is 5 miles long, 3 miles wide, and 70 feet thick; the other tongue is somewhat smaller. Ore bodies consist of a few hundred tons to several hundred thousand tons of material containing from 0.10 to about 2.00 per cent U3O8. The ore mineral is uraninite associated with pyrite, marcasite, hematite, and calcite. Deposition is believed to have taken place when neutral to slightly alkaline, oxidizing, uranium-bearing ground water, on entering the basin, encountered a reducing environment. The reductant may have been H2S of biogenic origin. Geology played an important role in discovery, exploration, and development of ore in the Shirley Basin.

Jan 1, 1968

INTRODUCTION This chapter summarizes characteristics of porphyry copper deposits within the Cordilleran orogen east of the Coast Range plutonic complex of the Yukon and British Columbia and south to the Columbia River plateau and the Idaho batholith. Porphyry copper deposits in this area reflect a geologic environment different from that found for mineralized intrusions elsewhere in the Cordilleran orogen, both to the south in the United States and Mexico and to the west in Alaska. A section on the Tertiary Cascade porphyry copper province is included herein. The Cascade province is considered separately because its deposits display a unique mineralogy and age of mineralization. That portion of the Cordilleran orogen described in this chapter is shown in Fig. 32, with the Cascades shown in Fig. 39 (see p. 114). The regional geology of this area has been described by Monger, et al. (1972), Hollister (1974), Wolfhard and Ney (1974), Field, et al. (1974), and Stacey (1974). Each offer slightly differing views on the post-Mississippian evolution of the geology in this porphyry copper province. The descriptive geology in this chapter has benefited from many discussions with J. E. Armstrong and J. W. H. Monger. Two separate petrologic models have been used popularly to categorize porphyry copper deposits in this area, a diorite and a quartz monzonite model. The diorite model, which involves a mineralized quartz-free pluton, has also been called the alkalic type (CZM Special Volume 15, 1976, and Soregaroli, 1975) and the syenite suite (Sutherland Brown, et al., 1971). The quartz monzonite model has also been named the calcalkalic type (CZM Special Volume 15, 1976) and includes mineralized quartz-bearing plutons compositionally ranging from quartz diorite to granite, with the igneous phase closest to ore in time and space commonly being quartz monzonite.

Jan 1, 1978

By C. H. Li, R. J. Stokes, T. L. Johnston

Sodium chloride crystals are brittle in the presence of surface microcracks. Water immersion leads to an enhancement of ductility which is retained indefinitely in dry air providing the crystal is dried without leaving a surface precipitate. Storage in a damp atmosphere results in a surface reaction and consequent rembrittlement. Although elimination of surface flaws in ionic solids does not necessarily enhance ductility, there is always a change in the location of the fracture origin. EVER since the original experiments of Joffel there has been controversy over their interpretation and no satisfactory generalized explanation has yet been given. It is generally admitted that when sodium

Jan 1, 1961

By W. P. Lass

The purpose of this article is not only to describe the plant and method of cyaniding the Treadwell concentrates, but to present some of the results of the experimental work obtained in the past three years for the Alaska-Treadwell Qold Mining Co., at Douglas Island, Alaska, under the direction of F. W. Bradley, Consulting Engineer, and Robert A. Kinzie, General Superintendent, of the affiliated companies. At the time the experimental work was undertaken the concentrates were being shipped to the smeltery at Tacoma, Wash., and the cost for treatment of 3-oz. (gold) concentrates was $11.95 per ton, divided as follows : Smelting-charges,......... $4.00 Loading, freight, insurance, etc., . 2.89 Interest due to time loat in transit and in settlement,... 0.05 Loss due to settlement for 95 per cent. of the gold at $20 per ounce, 6.01 Total,...$11.95 From the experimental work described later, it was estimated that 96 per cent. extraction could be made by treatment on the ground, and that the cost, when treating 80 tons per day, would be $3.25 per ton, divided as follows : Per Day. Per Ton. Labor,. $86.16 $@.827 Chemicals,.76.60 0.960 Power and steam-heat,... 67.60 0.845 Marketing-, refining- and other charges, . 49.36 0.617 Totals,.. $2.59.72 $3.250 Adding to this total the 4 per cent. treatment-loss, which on 3-02. concentrates amounts to $2.48, gives a total cost of $5.13 per ton. Comparing this with $11.95, the cost when shipping to the smelter, leaves a net gain of $6.22 per ton by the local

Jan 1, 1912

By H. l. Burghoff, A. I. Blank

The state of knowledge bearing on the stability of copper under stress at elevated temperatures is generally known to be in need of revision and extension. The present investigation, dealing with the creep characteristics of a deoxidized copper of low residual phosphorus content, is intended to contribute in some small measure toward this end. The experimental data presented herein have been correlated by methods of evaluation and interpretation familiar to those who are concerned with crecp of metals. In practice it is common, if not requisite, to use structurally stable materials at elevated temperatures. It is frequently desirable, however, to test materials under conditions that produce structural change, in order to determine the extent of such change and its effect on physical properties, thus making it possible to establish accurately the limiting conditions to which such materials may be safely exposed. The creep characteristics of the drawn copper wire of this investigation arc directly associated with its structural instability at elevated temperatures. Complete realization of this fact is essential to the evaluation of its creep resistance under various conditions. Creep results should apply to steady deformation under equilibrium conditions, but these are seldom attained in only one or two thousand hours. It will be shown that steady creep rate for copper at useful stresses does not usually begin until considerably more time has elapsed. A wholly satisfactory substitute or shortcut for extensive creep testing does not appear to be evident in the application of mathematical analyses to limited experimental data. Material A single lot of phosphorized copper wire was drawn down to 0.125-i11. diameter with a final reduction of 84 per cent. After mechanical straightening, a portion of this wire was annealed to an average grain size of 0.013 mm. in a controlled-atmosphere furnace. The composition and initial properties of the copper in these two conditions are listed in Table I. Photomicrographs of the original structure are shown in Fig. I.

Jan 1, 1945

By H. C. Schultz

CERTAIN local conditions were known to govern in large measure the successful adaptation of liquid-oxygen explosives to the large-scale blasting at Chuquicamata. The wide variation in hardness of the rock at this mine makes necessary the use of several types of explosives. A locally manufactured, relatively cheap black powder is used in blasting the softer waste and capping material, where a thorough displacement, breaks the ground sufficiently. Before the introduction of L. 0. X., an ammonia dynamite of about 65 per cent. strength was being used exclusively in the harder underlying orebody, where a strong disruptive as well as a displacement effect is required for breaking the ore. The L. 0. X., as developed for quarry work in the United States, has a practically pure carbon cartridge material, and the explosive has an extremely high rate of detonation, which should therefore cause it to usefully develop its full disruptive effect in hard ground. The individual blasts at Chuquicamata are large, black-powder shots which dislodge masses of rock averaging 250,000 tons each, and dynamite shots which dislodge masses averaging 80,000 tons each. It was desirable, therefore, to attempt to displace with L. 0. X. the faster, higher-cost ammonia dynamite used in the smaller blasts. It was not considered practical to attempt to displace the low-cost black powder with L. 0. X., as estimated costs showed no probable saving if this were accomplished. Since it was desirable to continue shooting relatively large blasts for effective operation, it was recognized that larger storage facilities than had been in use would be needed for the liquid oxygen. Because of the difficulty of transporting and discharging large storage containers of efficient design, the better plan appeared to be storage and discharge of the liquid at the place of manufacture, and transportation of the filled soaking boxes to the blast.

Jan 1, 1928

By Roger E. Barthelemy

PRIMITIVE mining and metallurgy has today almost disappeared. Probably the only remaining tribal tin mining and smelting is practiced by the Laotian natives in one of the less known tin areas of the world. This district lies almost a thousand miles from the sea along the Mekong River, one of the longest rivers in the world, that marks the border between Siam and Laos, one of the five states forming French Indo-China. Less than twenty years ago it took more than two weeks' travel on elephant-back to reach the spot and today it still takes many days of travel, using all kinds of transportation from automobiles to native

Jan 1, 1938

By J. J. Lander, L. H. Germer

Molybdenum and tungsten have desirable corrosion and temperature resistant properties, but the metals in bulk are expensive and their fabrication is difficult. Such considerations led to a search for a method of plating them upon base metals. This search was successful and led furthermore to a number of developments which could not have been foreseen. Neither pure tungsten nor pure molybdenum has been electroplated successfully, although the literature of electroplating is liberally sprinkled with the description of unsuccessful attempts. The process of plating these metals by thermal reduction of their halides has achieved onlv limited usefulness because of technical limitations and because of limited range of product quality. Plating by thermal decomposition of the carbonyls does not suffer from limitations of the same sort and the properties of the plate are readily controllable. This paper describes the plating of molybdenum and tungsten, and of compounds and alloys of these metals, by pyrolysis of their carbonyl vapors. Chromium also has been plated in this manner, but the experiments upon chromium have been less extensive and the results much less satisfactory. Probably the most important of the products which we have obtained are the alloys with carbon, and the carbides of the metals. Either molybdenum or tungsten can be deposited upon a base metal as a coherent and adherent coating. By adjusting the plating condition the carbon content of the coating can be made to have any value from substantially zero to about 35 atomic pct. The hardness is dependent primarily upon the amount of carbon in the plate and can be regulated over a very wide range, some coatings containing considerable carbon being harder than sapphire. In addition to products already known this method of plating has yielded new carbides of molybdenum and tungsten and alloys supersaturated with carbon. These new products are possible because, in the process of plating, carbonyl can be decomposed at temperatures as low as about 150°C, and thus in the presence of other substances reactions occur which could perhaps not be produced in any other way. In addition to carbides and alloys with carbon, sulphides and oxides of molybdenum and tungsten have been produced and studied. There are certain other advantages of the carbonyl method of plating. It is not required that the base have good electrical conductivity as in electrochemical processes, and the base need not have the temperature stability required in plating from a halide. Thus low melting glasses, as well as other ceramics, can be plated almost as readily as metals. In particular, the plating of glass with

Jan 1, 1949

By J. F. Martin, J. E. Friedline, L. M. Melnick, G. E. Pellissier

A method has been developed for determining gases in steel in which the gases are extracted by vacuum fusion and analyzed by mass spectrometry. This method is especially applicable for determining small amounts of oxygen and nitrogen. The lower limit of detection for both oxygen and nitrogen is 0.0001 pct with an average deviation of about 0.0001 pct for oxygen and 0.00008 pct for nitrogen. Hydrogen analyses by this method are in good agreement with analyses by vacuum tin-fusion. A complete analysis of all gases extracted from a steel sample can be accomplished in 40 min. It has long been known that certain of the gaseous elements exert particular effects on the physical and mechanical properties of steel. With the recent advent of new experimental steelmaking practices it is now possible to obtain steels with extremely low contents of such elements as oxygen and nitrogen. Present methods for determining these two gases are of insufficient sensitivity as applied to steels made by these newer practices, and therefore a new technique was considered necessary. A review of the literature showed that the conventional vacuum-fusion method1 was the procedure most suitable for modification to obtain a sensitive method for determining the gaseous elements present in steel simultaneously. However, for trace amounts of gases it is impractical to increase the sample size because of the physical limitations of the apparatus and the increased degassing time which would be necessary. Also, when only one of the desired gases is present in trace amounts, quantitative separation by conventional vacuum fusion is almost impossible. Since small analytical mass spectrometers are now commercially available, it was decided to use this instrument in conjunction with conventional vacuum fusion for both qualitative examination and quantitative determinations of the gaseous elements in steel. This technique has already been used with success for the analysis of copper and lanthanum.2"4 APPARATUS A vacuum-fusion unit was first designed and built, Fig. 1. This unit was designed especially for the determination of small amounts of nitrogen and/or oxygen in steel since an acceptable method (vacuum tin-fusion)5 was already in use for the determination of hydrogen in steel. The vacuum system was con- structed of Pyrex glass throughout. Mercury check valves were used in place of stopcocks in the high-vacuum section of the system. Ferromagnetic samples are normally introduced into the vacuum system through a mercury lift. In case of a break in the lift, the mercury is prevented from entering the furnace by a self-locking, mercury safety check valve, Fig. 2. This check valve, developed at our laboratory, is a modified T/S ball-and-socket joint placed in the sample inlet system between the mercury and the furnace. A sudden entry of mercury or air pushes this valve into the closed position, completely blocking the top of the mercury lift. The check valve is held in the closed position by the vacuum of the apparatus. A separate entrance tube also was placed in the system, so that samples which would amalgamate with mercury, or which are nonmagnetic, could be introduced into the furnace. A slightly modified Guldner-Beach furnace is used in this system.8 The optical flat was connected to the system by a ground-glass joint to facilitate cleaning, a quartz delivery tube was substituted for Pyrex, and the crucible was used uncovered. Fusion takes place in a high-purity graphite crucible insulated by — 200-mesh high-purity graphite powder. The crucible set (crucible and funnel) is suspended in a quartz crucible. The furnace envelope and the sample inlet system are exhausted by 2 single-stage, mercury-diffusion pumps in series. The first of these is a high-speed pump, which will work only with a very low backing pressure. This pump is used to exhaust the gases from the furnace as rapidly as possible. The second mercury-diffusion pump is used as a backing pump for the first; the capacity of this pump is much lower. However, it will work efficiently against a back pressure of 3 mm of mercury. To assure positive pumping, a modified Naughton and Uhlig condenser7 is used. With the use of proper valving the second pump is also used as a circulation pump in the catalyst system.

Jan 1, 1959

By D. C. Hilty, W. Crafts

The solubility of oxygen in iron containing aluminum has been determined at 1550°, 1600°, and 1650°C and found to be much higher than predicted from theoretical considerations, possibly due to equilibria with an iron-aluminum spinel phase rather than pure AI,O.. The presence of manganese greatly increased the deoxidizing power of aluminum. DEOXIDATION and inclusion formation in steel have proved to be elusive phenomena that are difficult to control in spite of much effort to understand and evaluate the reactions. Study of the problem indicated that more accurate data on the solubility of oxygen in iron containing deoxidizers were essential to further progress, and an empirical determination of oxygen solubilities has been initiated at the Union Carbide and Carbon Research Laboratories, Inc. The investigation has included the effects of aluminum, silicon, manganese, and combinations of these elements at 1550°, 1600°, and 1650°C. The equipment and experimental procedure as well as the results of a study of the effects of aluminum are described below. In general, it was found that the solubility of oxygen in iron containing aluminum is much higher than predicted, possibly because of the formation of complex nonmetallic phases, and that manganese greatly increases the deoxidizing power of aluminum. The generally accepted deoxidation curves for 1600°C are summarized in fig. 1, from "Basic Open Hearth Steelmaking"'. These curves are assumed to represent the solubility of oxygen in the presence of deoxidizers and should indicate the limits of mis-cibility gaps in the phase diagrams of the systems that control the formation and character of non-metallic inclusions as described by Benedicks and Lofquist'. They were derived mainly by application of the methods of thermodynamics to the available experimental observations, and by calculations based on the thermal constants of the pure substances when experimental data were lacking. Among the more notable researches contributing to the development of knowledge of oxygen solubilities are those of Korber and Oelsen8, 4, C. H. Herty, Jr. and associates5,6, Krings and Schackmann7, Went-rup and Hieber8 Schenck and Briiggeman9, Vacher and Hamilton'" and Chipman and co-authors 1,11,12,13 Practically, the deoxidation curves are of limited value in predicting oxygen content and rationalizing deoxidation practices. The reasons for this inadequacy appear to be error from inaccurate data, oversimplifying assumptions, interacting effects of combined deoxidizers, and possibly unknown extra-equilibrium and side reactions. Although inclusion formation is a very complex reaction it must be re-

Jan 1, 1951

By Bailey, Lewis Newton

Bailey, Lewis Newton, Master Engineer, Senior Oracle, 4th Regiment, U. S. Engineers, Headquarters Company, died of pneumonia, at Camp Merritt, N. J., on April 30, 1918. Baird, Louis, Lieut., Royal Field Artillery, British Army, died on the battlefield in 1915. Ballamy, John H., Capt., 103d Engineers, killed in action near Fismes, Aug. 9, 1918. Burt, Andrew, died in active service, 1916. Cobeldick, William Morley, Royal Engineers, died from gas poisoning on October 7, 1915. Dougall, Ralph, 4th University Co., Princess Patricia Regiment, killed in action early in the war. Evans, Alfred Winter, Lieut.-Col., New Zealand Rifle Brigade, D. S. 0., D. C. M. killed in action on October 12, 1917. Gorman, Thomas C., Lieut., Canadian Engineers, killed in France, Mar. 18, 1918. Hague, William, 1st Lieut., Engineer Officers' Reserve Corps, died in active service, Jan. 1,, 1918. Hall, William T., Capt., Royal Flying Corps, killed in action, May 19, 1917.

Jan 11, 1918

By C. R. Kuzell

ALTHOUGH furnaces constructed of refractory brick have been oper-ated for many decades, there has always been an unfulfilled desire by the operators for a less arduous and more satisfactory method of patching weak spots and burned-out zones in order to postpone and to effectively extend the termination of a furnace campaign. Not only has this desire frequently arisen when small spots have approached incipient failure while the furnace structure as a whole was still in good condition, but also when larger areas showed signs of needing replacement. The availa-ble methods have been arduous, sometimes dangerous, inefficient with respect to the life of new refractory material used, and nearly always have necessitated interruption of the continuity of the furnace operations and therefore reduction in furnace production during the period of time required for the repair work. Most of these older methods have involved the replacement of masonry by refractory shapes in the weakened areas. Many attempts have been made to develop a method of patching the burned-out areas by spraying granular refractory material upon old surfaces. While some success has been attained in attempts to renew the grooved, corroded side walls and fettling, and the edges of hearths, there have been no known successful applications of the spraying method in patching the underside of arches of operating furnaces. The method developed recently at the Clarkdale smelter of the United Verde Branch of Phelps Dodge Corporation, at Clarkdale, Ariz., and described in this paper, has been found to be not only convenient and successful with respect to patching vertical or inclined surfaces, but has met with a marked degree of success in patching the parts of furnace arches that are exposed to flame, the successful result being obtained with-out interruption or interference with the continuity of furnace operations. ? It may be described as a method of renewing the interior refractory sur-faces of operating furnaces by pneumatic spraying of an aqueous suspen-sion of finely divided particles of refractory material. It has been used

Jan 1, 1939

By M. L. Pearce

A comparison of the isotope-dilution, vacuum-fusion, and chemical methods of analysis for nitrogen in Si-Fe is made with particular emphasis on the effect of sample history. The superiority of the isotope-dilution method from the point of view of 1 HE analytical techniques used to determine nitrogen in Si-Fe have been subjected to close scrutiny in recent years primarily because of the marked influence of the element on the properties of the alloy. These investigations have led to a diversity of opin- both precision and accuracy is demonstrated. The solubility of nitrogen in 3.06 pct Si-Fe is investigated and the effect of silicon content on the activity coefficient of nitrogen is derived. ion regarding the reliability of the vacuum-fusion and chemical methods of nitrogen analysis when applied to si- Fe.'-' A majority of workers appear to favor the vacuum-fusion method over chemical methods particularly in those cases where part of the nitrogen may exist as silicon nitride or the total nitrogen content is very low. Contrary views have been expressed, however,' and it has been demonstrated that for some Si-Fe alloys both methods yield results which are significantly lower than those

Jan 1, 1963

By Edmond S. Miksch

The morphology and growth rate of ice grown in supercooled water are markedly affected by convection of the water. A dendritic ice sheet with water flowing past the dendrite tip exhibits deflection of the dendrite spine toward the upstream direction, accelerated growth of secondary spines on the upstream side, and suppression 01" secondaries on the downstream side. Flow causes a thin disk to become corrugated, the corrugations being parallel to the flow. Flow causes an increase in the growth rate of the ice. IF a small seed of ice is placed in slightly supercooled water, it grows initially as a disk with the axis of the disk parallel to the c axis of the ice crystal.' It appears that growth in the c direction is inhibited, while growth occurs with equal facility in all directions in the basal plane. It appears that growth rate as a function of interface temperature is very nearly equal for all directions similarly oriented relative to the c axis. Subsequent to the discoid growth, branching occurs and dendrites develop. The primary dendrite spines grow parallel to the six equivalent a axes of the crystal. Secondary, and in some cases, tertiary spines also grow in these directions. The highly anisotropic: dendritic growth indicates that there must be some finite difference of growth rate for different directions in the basal plane. These differences must be quite small, however, since if they were large, the discoid mode would not occur. Hence, it was expected that the dendrite growth direction could be deflected from the crystallographic direction by perturbation of the thermal field at the dendrite tip. Experiments were done in which perturbation of the thermal field was accomplished by causing the supercooled water to flow past the dendrite tip. The flow direction was perpendicular to the c axis of the crystal, and was perpendicular to the primary spine of the unperturbed crystal. Supercooled water was supplied by a 15 cm cubical copper box, which was refrigerated and insulated so it could cool water to temperatures down to —2oC, and maintain the temperature constant to O.l°C for the duration of a run. A lucite channel of rectangular cross-section, 12 by 24 mm, was mounted horizontally in the box, with one end open so water could flow into it, and the other end leading out through the wall of the box to a length of tubing leading: to an orifice plate 123 cm below. cnunMn s MIKSCH, MemberAiMe, formerly Research Associate, Research Associate, Fig. l(b)—Vertical section of apparatus A horizontal cross-section is shown in Fig. l(a), and a vertical section is shown in Fig. l(b). Means for observing the ice are shown in Fig. l(a). Collimated light passes through the ice sheet and forms an image on the ground glass screen. A lucite box containing dry air was employed to prevent condensation. Ice of the desired orientation was provided by the seed holder shown in Fig. l(b). This device was made of lucite, and had a reservoir in which ice could be frozen by placing it in a freezer. This reservoir com-unicated with the outside only through a narrow gap between two sheets of lucite. The seed holder (after ice had been washed off its exterior) was immersed in the tank of supercooled water, the narrow gap terminating in a slot in the top of the flow channel. Ice growing through a thin water layer in the gap between the two sheets of lucite was oriented so its c axis was perpendicular to the sheets. This orientation is an application of a growth phenomenon2 which causes ice growing along a smooth solid surface in supercooled water to orient itself so its c axis is normal to the surface. After the ice grew into the channel, further orientation was necessary, since the direction of the a axis

Jan 1, 1970