Search Documents

By Gail F. Moulton

The production of petroleum in Illinois in 1928 was approximately 6,500,000 bbl., a decline of about 500,000 bbl. from the previous year and of about 1,500,000 bbl. from 1924. Production increased about 200,000 bbl. in Indiana to slightly less than 1,000,000 bbl. Production for 1929 is estimated at approximately 6,000,000 bbl. for Illinois and 1,000,000 bbl. for Indiana. Illinois Because production from most of the wells in the state has declined to a small daily average and the low prices for crude oil discouraged wildcatting, the number of wells drilled fell below that for any previous year since the development of commercially important production in the state. The Ohio Oil Co. discovered a pool of apparent commercial importance in southwestern Illinois near Dupo, in St. Clair County, and favorable showings of oil were encountered in a well in southeastern Illinois, near Harrisburg in Saline County. New production from the Dupo area is expected to check the rate of decline for the state. Thc following tablel summarizes field developments for 1927 and 1928 (for important detail by counties see notes at foot of table): 1027 1928 Completions........................................... 162 145a Initial production, bbl.................................. 2244 1840b Dry holes........................................,.... 66 58" Gas well completions................................... 13 8d 0111 wells abandoned.................................... 45" a Crawford, 44; Lawrence, 28; Wabash, 40. b Crawford, 501; Lawrence, 403; St. Clair, 165 (4 completions); Wahash, 668. o Crawford, 12; Wabash, 19. d Crawford, 6. b Lawrence, 21; Wabash, 15. The discovery well in the Dupo field in St. Clair County, produced about 150 bbl. per day from the Trenton lime at 660 ft. It is located in a northern extension of the Columbia-Waterloo anticline on which the Waterloo pool was developed in 1921. The best information on the.

Jan 1, 1929

By Geoffrey Purcell

For anyone contemplating flotation research with only a very limited amount of mineral available for testing, the choice of suitable experimental equipment is by no means obvious. Hallimond's original and delightfully simple cell1 has been modified by subsequent investigators2to give quantitative and reproducible results on small samples. However, the modifications have necessarily compromised its simplicity, and the services of a skilled glass blower are required to duplicate the cell. Vacuum flotation tests3 at best qualitative and may, under certain conditions4, be quite impracticable. A hundred years ago, Thoreau observed that "our life is frittered away by detail," and his advice was to "simplify, simplify," The success of the simple cell described below, which was developed by the author and differs somewhat from Hallimond's original, suggests that Thoreau's advice still has merit a century later. CELL CONSTRUCTION The cell [Fig. 1 (a) and 1 (b)] consists essentially of a 25-ml pipet from which has been cut the con- stricted top. The length cut off is not critical since this merely determines the final volume of the cell. Cell volume may be varied in this way from 20 to 50 cc. A pyrex extension tube, equal in diameter and approximately half the length of the cut pipet, is attached to the top of the pipet by means of 2 ½ in. of close-fitting tygon tubing. When assembled, the two pyrex tubes should be spaced about ½ in. apart. Another length of tygon tubing is added to the extension piece for sealing purposes. A ¾ -in. disc of porous material (teflon cloth is ideal), secured in place over the pipet tip with another piece of shaped tygon tubing, completes the cell assembly. Tygon tubing may be shaped by pushing it over the pipet tip or some similar form and heating carefully over a low flame. For flotation [Fig. 1 (c) 1, the pyrex extension tube is rotated approximately 70º from the vertical and held in position by a wire hook and eye. Floated material, after reaching the free surface, falls and rests on this inclined plane. The barrier formed by the bent tygon tubing ensures that floated material does not slide back and return to the vertical portion of the cell.

Jan 11, 1965

By A. S. Odeh

This paper analyzes the effect of limited entry to flow at the wellbore on the steady-state productivity of a well. Wells that have been opened to flow along a fraction of their productive interval are termed wells with limited entry. Previous work treated the cases of a partially penetrating well, a well producing from the central portion of the productive interval and a well in which several intervals equally spaced were open to flow. In this paper the open interval can be located anywhere within the productive interval. Thus, in a sense, it generalizes previous work. The finite cosine transform was used to arrive at a solution for steady-state flow of a slightly compressible fluid. The solution was programmed for a CDC 1604 computer. Numerical vaIues for rd = 660 ft, r, = 1/4 ft, and range of sand thickness of 20 to 200 ft are presented in graphical form. The effect of rd and r, values on the result is shown in a table. The correct calculation of skin and damage ratio in the presence of limited entry to flow is explained and illustrated by examples. Moreover, the paper shows how to calculate the net decrease in productivity due to the combined effect of limited entry and perforations. INTRODUCTION In some wells only a fraction of the productive interval is open to flow. Location of this fraction is usually dictated by formation characteristics and reservoir behavior. For instance, if a gas cap exists, the open interval is located away from the gas-oil contact to prevent any possible gas coning. Wells that intentionally have been opened to flow along a fraction of their productive formation are tened wells with limited entry. Obviously, unintentional completions of this type also exist. Limited entry to flow decreases well productivity. Magnitude of the loss depends on the fraction of the formation open to flow, on the thickness of the sand, on the location of the open interval and on the ratio of rd /r, where r , is well radius and rd is the drainage radius of the well. The use of pressure buildup data on producing wells to calculate the condition of the formation around the wellbore is an accepted practice. van Everdingenl and Hurst2 introduced the concept of she skin factor s considered to be due to a thin layer of different permeability immediately around the wellbore. These authors dealt with the case of a well of complete radial geometry, i.e., a well with open-hole completion that completely penetrates the formation. The presence of a low-permeability skin results in a loss of productivity, as does limited entry. Therefore, if pressure buildup data obtained on a well with limited entry are used to establish the presence or absence of skin (i.e., formation damage), and a correction is not made for this loss of productivity, the calculations would result in an erroneous skin value. They might indicate the presence of formation damage when in reality there is none, or they might indicate a value larger than the true value. This could lead to an incorrect basis for planning remedial measures. Muskat3 studied the problem of partially penetrating wells for the case of incompressible flow. He presented equations and figures which allow estimation of loss in productivity. Brons and Marting,4 using equations based on Nisle's work,5 studied the loss of productivity for three cases. The first was for a partially penetrating well; the second was for a well producing from only the central portion of a productive interval; and the third was for a well in which several intervals equally spaced were open to flow. Their work was for steady-state depletion-type reservoirs wherein the well radius of drainage is established and the fluid is considered to be slightly compressible. Considered in this paper is the problem of wells with limited entry in which the open intervals are located anywhere within the productive sand. The finite cosine transform is used to arrive at a

Jan 1, 1969

By William B. Phillips

It is proposed in this paper to discuss some of the chemical and physical principles involved in the manufacture and use of this important by-product obtained in the manufacture of steel by the basic process. The name, " phosphate slag," is adopted as a sort of compromise between "Thomas slag" and "tetrabasic phosphate." By the first of these latter names, viz., " Thomas slag," it is known in Germany, Austria, France, and the other continental countries, and in England, and is more easily apprehended by those who have no special Knowledge of chemistry, while the name " tetrabasic phosphate," being descriptive of the nature of the slag, is perhaps the best. It is but seldom that a discovery of such moment to two great industries is to be chronicled in the history of technical science. On the one hand, the manufacture of iron and steel has been greatly benefited, while on the other hand, the effects already noticed, and still to follow, to the agriculturalist, are of scarcely less conseqnence. The great majority of iron ores in the world, perhaps 90 per cent. of then), are now available for the steel manufacturer, while the manufacturer, and more especially the consumer, of artificial manures is relieved from the fear of the exhaustion of the crude phosphates. We have in phosphate slag, therefore, a product of the highest importance to those who make and we steel and fertilizers. Two great industries, which heretofore have had but little in common, are thus brought into close connection with each other, and the results sure to follow, if one may judge from the history of the past ten years, cannot fail to be of great and increasing value. These results may be compared with those which followed the introduction of the cupriferous Spanish pyrites into England for the manufacture of sulphuric acid. The copper extracted greatly reduced the cost of the acid, hence that of artificial manures. Cheap manures meant better farming and cheaper farm products, and these meant better and cheaper living to nearly all classes of society. The amount of fertilizers now manufactured in the United States

Jan 1, 1889

By P. H. Brace

THE study of the relations between gases and metals is one of perennial interest to all who are connected with the production of high-grade metallurgical products. The data reported here are the outcome of work of which the object is to determine the effects of dissolved gases upon the properties of metals and to gain a more detailed knowledge of the reactions between gases and molten metals, particularly; iron, under definitely controlled conditions. We have attempted to reduce our margin of error by dealing with relatively large quantities of metal, from 4 to 13 lb. (2 to 6 kg.), and keeping the ratio of refractories to metal as small as practicable. The ingots produced are large enough to provide adequate material for making determinations of magnetic and other physical properties. In choosing the bell-jar type of furnace we were influenced by the results of considerable experimentation along the same general line which indicated that, for the scale or which we were to work, it was important to have the furnace structure independent of the vacuum enclosure. The use of a bell-jar surrounding the entire furnace accomplishes this and also gives great freedom of observation during operation and ready accessibility for the replacements which are necessary after each run. Our choice of analytical method was made in the light of the results secured by H. M. Ryder, who used a method similar in principle for the analysis of very small quantities of gas extracted from strips of metal heated electrically in high vacuum. We have presented some selected preliminary experimental data as being illustrative of the quantity and nature of the gases which occur in iron of different origins, but do not urge any hypothesis at this time.

Jan 1, 1928

By P. H. Brace

THE study of the relations between gases and metals is one of perennial interest to all who are connected with the production of high-grade metallurgical products. The data reported here are the outcome of work of which the object is to determine the effects of dissolved gases upon the properties of metals and to gain a more detailed knowledge of the reactions between gases and molten metals, particularly iron, under definitely controlled conditions. We have attempted to reduce our margin of error by dealing with relatively large quantities of metal, from 4 to 13 lb. (2 to 6 kg.), and keeping the ratio of refractories to metal as small as practicable. The ingots produced are large enough to provide adequate material for making determinations of magnetic and other physical properties. In choosing the bell-jar type of furnace we were influenced by the results of considerable experimentation along the same general line which indicated that, for the scale or which we were to work, it was important to have the furnace structure independent of the vacuum enclosure. The use of a bell-jar surrounding the entire furnace accomplishes this and also gives great freedom of observation during operation and ready accessibility for the replacements which are necessary after each run. Our choice of analytical method was made in the light of the results secured by H. M. Ryder, who used a method similar in principle for the analysis of very small quantities of gas extracted from strips of metal heated electrically in high vacuum. We have presented some selected preliminary experimental data as being illustrative of the quantity and nature of the gases which occur in iron of different origins, but do not urge any hypothesis at this time.

Jan 1, 1928

By L. C. Uren

Some of US have been impressed with the need for a better understanding of the future place of the engineer in the petroleum industry. In academic work we are continually asked to advise students as to the opportunities in different directions, to guide them in their selection of professions, and it would be extremely helpful to those in academic lines of work to have the opinion of engineers from the industry relative to the need for petroleum engineers. IS the industry going to require a continually growing number of engineers in the future years, or have we perhaps reached equilibrium in that regard ? In anticipation of this meeting, I undertook to canvass opinion among a number of engineers of my acquaintance and I have been rather astonished to learn that the expenditure on engineering salaries in the producing branch of the oil industry is extremely low. I have figures from eight or 10 of the larger oil companies and it seems to be a fair statement on the basis of these figures to say that the average American oil company is devoting less than 2 per cent. of its gross expenditures in oil production to the payment of engineering salaries. A few examples will be of interest. I shall not mention names of individual companies, but one large Mid-Continent company is spending slightly less than 1 per cent. of its gross expenditure—that is, less than 1 per cent. of the total expenditure in the producing department—on engineering salaries and about as much on engineering research, which might properly be regarded as a phase of its engineering work. Another Mid-Continent company is spending about 11/4 per cent. on engineering salaries. A large California company is spending about l1/2 per cent. The largest figure that has come to my attention is that of an important Rocky Mountain and Mid-Continent company that is spending a little more than 6 per cent., but that is apparently an extreme case. The petroleum producing industry is a highly technical business in these days. It is spending in excess of $500,000,000 annually in new

Jan 1, 1929

By G. R. Fritterer

INVESTIGATORS in the field of temperature measurement have long sought a thermoelectric couple fulfilling the following requirements: 1. It should be useful up to and including high industrial tempera-tures; i. e., 1000° to 1800° C. 2. Its thermoelectric variation with temperature should be linear and be maintained after heating to high temperatures for long periods of time. 3. It should be reproducible; i. e., different couples of the same elements should have similar calibration curves. 4. Its thermoelectric power should be large so as to allow the industrial use of rugged recording instruments. 5. Chemical reactions with, and physical changes within the elements of the couple should not alter its calibration. No thermocouple proposed to date exhibits simultaneously all of these characteristics, whereas the couple about to be described fulfills all requirements to a satisfactory degree.

Jan 1, 1933

By G. F. Comstock

THE subject of transverse fissures in steel rails has been discussed very thoroughly in recent years from various points of view and the final opinions expressed may be roughly classified into two groups: (1) That these fissures are the result merely of fatigue of the steel and are independent of the quality of the metal. (2) That the quality of the metal and the mill practice must have something to do with them. The first point of view was most-ably and logically presented by J. E. Howard,1 and in the discussion of this paper, as well as in several other preceding publications, Dr. P. H. Dudley, Consulting Engineer of the New York Central Lines, has strongly defended the other opinion.2 The steel makers of the country have naturally rallied under Mr. Howard's banner, hoping to place the entire blame for these. failures upon the railroads with their high wheel-loads, hard steel, heavy traffic, and sometimes inferior roach-bed; while the railroad men,, on the other hand, have been busy accumulating statistics and records in the effort to find an actual reason in the rails themselves that would account for the seemingly haphazard occurrence of transverse fissures under varying conditions and at widely separated points. The view that these fissures were due merely to normal fatigue under alternating stresses seemed most reasonable to the writer until quite recently, because from work clone in this laboratory, as well as the work of other investigators of the problem, no structural differences, in the vast majority of cases, were found between metal at the nuclei of transverse fissures and metal at similar positions in the same rails or in other rails that had not developed fissures. . Within the last year or two, however, since the method of etching polished sections for the microscope with a cupric chloride solution has been tried systematically. on lengthwise sections, passing through the nuclei of transverse fissures, evidence

Jan 11, 1918

By R. F. W. Pease, R. A. Ploc

A scanning electron microscope with a resolving power better then 100Å has been developed for the direct examination of surfaces. This instrument was used to study iron undergoing oxidation at 500°C. It was found that the electron current in the scanning electron microscope was low enough (about 10-atrzp) to have no observable effect on the growth of the oxide. "Armco " iron, when oxidized, exhibited an oxide film whose thickness and whiskey population varied with pain orientation; but purer iron, when oxidized, exhibited no such pain dependence and whisker occurrence appeared to be caused by impurities. UNTIL recently most surfaces of opaque specimens could either be studied with a light microscope or, if higher resolution was required, by viewing a replica of the surface in a transmission electron microscope. Direct electron microscopy of a surface has, in general, proved difficult owing to excessive foreshortening and the poor image quality obtained. The scanning electron microscope, however, offers an alternative method of directly viewing a surface without these disadvantages. At low magnification it offers a much larger depth of focus than the light microscope, and at high magnifications it offers much higher resolution (about 100Å). PRINCIPLE OF THE SCANNING ELECTRON MICROSCOPE A schematic diagram is shown in Fig. 1. The electron optical system consists of a gun followed by a series of lenses which focus the electron beam onto the surface of the specimen. The beam is scanned in a rectangular raster across the specimen surface and, by amplifying the secondary electron current from the 'pecimen, a picture of the specimen surface is built UP sequentially on the face of the display cathode-ray tube. The magnification of such a system is given by the ratio of the scan amplitude on the display cathode-ray tube to

Jan 1, 1965

By C. N. Kravig

STANDARD raises at Homestake are 150 ft long. Raises of more than 150 ft, driven with the use of a cage and hoist, are considered long raises- some have been driven more than 900 ft. Long raises have eliminated the need for access drifts on each level when transfer and ventilation raises are driven. These timbered cage raises, 7x9 ft in cross section, include a rock compartment and a combination cage, pipe, and manway compartment. To prevent excessive weight on the timbers, 10x10-in. bearing beams are cemented into hitches cut in the rock at 150-ft intervals. The beams also hold back timber movement caused by daily drawing of rock through the rock compartment.

Jan 6, 1957

By C. A. Crawford

NICKEL and the nickel-copper alloy, the latter generally referred to as morel metal, are available in a variety of wrought and fabricated forums, of which the following are regular commercial products: Form Monel Metal Pure Nickel Roc Hot-rolled; round, hexagon, Same as morel metal square, and flat shapes Cold drawn; round, hexagon, square, and flat shapes Hot-rolled wire rod Cold-drawn wire rod Plates Hot-rolled Same as morel metal Sheets Hot-rolled annealed Same as morel metal Hot-rolled annealed, pickled Full-finished Full-finished, No. 3 grind one side Full-finished, No. 4 grind one side Cold-rolled (annealed) Cold-rolled, No. 5 polished finish Strip Hot-rolled (flat rods) Same as morel metal Cold-rolled (annealed) Cold-rolled (unannealed) Tubes and pipe Gas-welded tube Seamless tube Seamless tube in I. P. S. Gas-welded tube Forgings Bolts, rivets Same as morel metal Nuts and washers Forging to order Castings Sand castings Same as morel metal Centrifugal castings Electrolytic Cathodes of high purity Anodes Cast anodes Rolled anodes Shot and block for 25 to 50-1b. pigs 5, 25 and 50-1b. pigs melting. Shot Shot

Jan 1, 1927

By M. Kaufman, A. E. Palty

THE mechanical properties of an alloy under given test conditions are in the main determined by the grain size and the phases present, their distribution and temperature-time dependence. Alloys intended for use at elevated temperatures, especially multiphase alloys depending upon precipitation reactions for strengthening, are particularly susceptible to changes in the phases present. Unfortunately, for modern superalloys, very little published information exists which relates the mechanical properties to the basic structural variables. The present work is an effort to do this for an alloy widely used in aircraft gas turbines and related applications, Udimet 500.* The mechanical properties inves- two heats is within the normal specifications for the alloy. However, the elements which most strongly influence the phase reactions, C, Ti, Al, and Mo, are comparable in the two heats. There was no intentional addition of boron, but normal pickup is about 0.002 pct. The vacuum-melted material was received in the form of centerless ground wrought bar stock % in. diam. PHASE STUDIES A) Methods—Two methods were used to determine the phases present: X-ray diffraction measurements on electrolytically digested residues, and microscopic examination. No single commonly used electrolyte will reveal all the phases that may be present; therefore, two complementary acids were selected: HCl and H3PO4. The necessity for this will be shown below in the results. The acid concentrations used were 10 pct HC1 in alcohol and 10 pct H3 PO4 in water. The current density was maintained below 0.1 amp per sq in. Residues were rinsed and separated by centrifuga-tion. X-ray diffraction patterns were obtained in a 114 mm Debye-Scherrer type camera using cobalt radiation. A temperature of 2250°F was selected to obtain as complete solutioning of phases as possible without encountering incipient melting. Specimens were

Jan 1, 1961

By Thomas Cox

This paper makes no claim to any new idea; it simply reviews the Treasury Department Regulations pertaining to the practical application of depreciation and depletion and other allowances governing taxation of oil and gas properties. Other methods may be existent, but as they may not conform to the legal status they must be discarded. In complying with the present laws governing the industry with regard to taxation and the allowable deductions therefrom, the following considerations are essential: Depletion, depreciation, amortization, other allowances, and items not, deductible. It is definitely understood that depletion is the loss or exhaustion sustained in the continuous operating of an oil and gas property, and that each unit of oil or gas taken out reduces the value of the property until its final exhaustion. Depletion applies only to the natural deposits of oil and gas due to their removal in the course of exploitation of any property. Depreciation is defined to cover the waste of assets due to exhaustion, wear and tear, and obsolescence of the physical property, and is separate and distinct from depletion; its allowance is that amount which should be set aside for the taxable year in such sums as for the useful life of the property will suffice to repay its original cost—or its value as of Mar. 1, 1913, if acquired by the taxpayer before that date—less the salvage value at the end of such useful life. Amortization is allowed for such facilities as were built or acquired on or after Apr. 6, 1917, for the production of articles contributing to the prosecution of the war and, in the case of vessels, those built and acquired after that date. The amount to be extinguished, in general, is the excess of the unextinguished or unrecovered cost of the property over its maximum value under stable post-war conditions. Claims for amortization must be unmistakably differentiated in the returns from all other claims of depreciation. The taxpayer is also required to furnish full information with the claims for amortization to the full satisfaction of the Commissioner. Further reference is directed to the specific rules and regulations for making these claims.

Jan 1, 1921

By George H. Willis

In the second half of the 19th century, bimetallism progressively was replaced by gold standard. After World War I and the 1931-33 depression, gold was mainly reserved for official international transactions and internal use was restricted. Changes since 1971 have shrunk official international use of gold. International payments deficits and surpluses are now financed by Private and official credit, rarely by gold. This historical review covers evolution of: (1) internal and external private use, (2) internal official use, (3) external official use, (4) its role in the International Monetary Fund, and (5) use as unit of account. For this paper I have tried to take a longer perspective than is usually possible, and to look, even if very briefly, at the changing relationship of gold to the monetary system over the last 200 years or so. There are, I believe, some long-term trends, continuing down to the present day. These trends have seen gold replaced by some form of paper assets in one monetary function after another. These past trends may help us to understand where gold stands now, and possibly will throw some light on the future. Because it seems to me that gold in the past has performed various functions related closely or marginally to money, I have divided this rapid historical review into several sections: (1) the internal and external private use of gold, (2) the internal official use of gold, (3) the external official use of gold, (4) gold and the International Monetary Fund, and (5)gold as a unit of account.

Jan 1, 1980

By C. E. Berner

Since 1933, the Coal Mine Rating Schedule in Pennsylvania has provided credits in the Workmen's Compensation insurance premium rates for the use of safety hats, goggles and shoes. In that year, the worth of such protective clothing had just been well established and satisfactory articles were being made by a number of manufacturers. Standards for these three items of safety clothing' were written in the Rating Schedule and have been little changed through the years. The credit in the premium rate for a bituminous mine is $0.14 for hats, $o.08 for goggles, $o.08 for shoes. In order to earn such credit, it is necessary that all the employees in the particular mine be equipped with safety hats, goggles or shoes, as the case may be. In fact, it is not unusual for mines to qualify in all three categories, thus earning a rate reduction of $o.30 per $100 of payroll. These credits have been a decided stimulus to the use of safety clothing, and at present insured bituminous mines are credited as follows: Hats........ 63 per cent, or 22,600 employees Goggles..... 28 per cent, or 10,000 employees Shoes....... 44 per cent, or 15,800 employees Of course, many other employees wear these protective articles but they are in mines that are not fully equipped and so are not given the rate credit. The growth in use of this equipment has not been spectacular but it has been steady, as shown in Table I. An interesting thing about this is that it covers virtually all of the small and medium-sized bitumi- nous mine operations in Pennsylvania. A number of large operations are included, but many large mines are self-insured. It is difficult to keep alive interest in safety work in the smaller mines: first, because employment of safety engineers is out of the question and the one or several mine officials employed are often concerned only with production; second, because the life of many small mines is brief, so that safe conditions although established do not last long. Conditions as to safety in mines of this class rest chiefly with inspectors of state mine departments and of casualty insurance companies. Many millions of tons of production come from these mines, so that

Jan 1, 1944

By C. E. Berner

Since 1933, the Coal Mine Rating Schedule in Pennsylvania has provided credits in the Workmen's Compensation insurance premium rates for the use of safety hats, goggles and shoes. In that year, the worth of such protective clothing had just been well established and satisfactory articles were being made by a number of manufacturers. Standards for these three items of safety clothing' were written in the Rating Schedule and have been little changed through the years. The credit in the premium rate for a bituminous mine is $0.14 for hats, $o.08 for goggles, $o.08 for shoes. In order to earn such credit, it is necessary that all the employees in the particular mine be equipped with safety hats, goggles or shoes, as the case may be. In fact, it is not unusual for mines to qualify in all three categories, thus earning a rate reduction of $o.30 per $100 of payroll. These credits have been a decided stimulus to the use of safety clothing, and at present insured bituminous mines are credited as follows: Hats........ 63 per cent, or 22,600 employees Goggles..... 28 per cent, or 10,000 employees Shoes....... 44 per cent, or 15,800 employees Of course, many other employees wear these protective articles but they are in mines that are not fully equipped and so are not given the rate credit. The growth in use of this equipment has not been spectacular but it has been steady, as shown in Table I. An interesting thing about this is that it covers virtually all of the small and medium-sized bitumi- nous mine operations in Pennsylvania. A number of large operations are included, but many large mines are self-insured. It is difficult to keep alive interest in safety work in the smaller mines: first, because employment of safety engineers is out of the question and the one or several mine officials employed are often concerned only with production; second, because the life of many small mines is brief, so that safe conditions although established do not last long. Conditions as to safety in mines of this class rest chiefly with inspectors of state mine departments and of casualty insurance companies. Many millions of tons of production come from these mines, so that

Jan 1, 1944

By H. W. Gillett

Many of the parts of motor cars, aircraft, etc., that require strong light construction, hence must be made of high-quality steel, are stressed to the maximum limit only in a very small volume. In parts subject to bending stress a line or even a point may take the maximum stress. A series of endurance tests under repeated bending in progress in the U. S. Bureau of Mines laboratories, like similar tests by other investigators, has shown the great difference in life of sister bars of the same stecl, handled in the same way and tested at the same nominal stress. It is known that a surface notch or scratch greatly increases the local stress over the nominal calculated stress; internal notches, such as those formed by inclusions or sonims, probably have a similar effect. From the tetss made by the Bureau of Mines, the cleanliness of the steel at the dangerous section, or point of maximum stress, seems to be one of the most important factors in determining the life of the piece. The more localized the stress, the more does chance, rather than the average properties, dctermine the life of the steel. The usual test, a tension test of a bar taken longitudinally, is not sensitive to the local drop in strength (or tendency to increase the true local stress over the nominal) because of inclusions, which probably have a more injurious effect in hard heat-treated steels, such as must be used when great strength is sought, than in softer steels. Users of steel who make transverse tests find surprisingly low ductility on transverse bars of dirty steel, though the longitudinal tests may be good. Bending tests, reverse bending tests, and notch-bar impact tests,

Jan 1, 1923

By H. W. Gillett

Many of the parts of motor cars, aircraft, etc., that require strong light construction, hence must be made of high-quality steel, are stressed to the maximum limit only in a very small volume. In parts subject to bending stress a line or even a point may take the maximum stress. A series of endurance tests under repeated bending in progress in the U. S. Bureau of Mines laboratories, like similar tests by other investigators, has shown the great difference in life of sister bars of the same stecl, handled in the same way and tested at the same nominal stress. It is known that a surface notch or scratch greatly increases the local stress over the nominal calculated stress; internal notches, such as those formed by inclusions or sonims, probably have a similar effect. From the tetss made by the Bureau of Mines, the cleanliness of the steel at the dangerous section, or point of maximum stress, seems to be one of the most important factors in determining the life of the piece. The more localized the stress, the more does chance, rather than the average properties, dctermine the life of the steel. The usual test, a tension test of a bar taken longitudinally, is not sensitive to the local drop in strength (or tendency to increase the true local stress over the nominal) because of inclusions, which probably have a more injurious effect in hard heat-treated steels, such as must be used when great strength is sought, than in softer steels. Users of steel who make transverse tests find surprisingly low ductility on transverse bars of dirty steel, though the longitudinal tests may be good. Bending tests, reverse bending tests, and notch-bar impact tests,

Jan 1, 1923

By C. G. Durdaller, W. H. Robinson, G. M. Pound

The nucleation rate of the a (pay) to 0 (white) tin transformation was measured as a function of temperature and a tin particle size using an X-ray diffraction technique. The powder specimens of a tin were essentially monodisperse and the small dinzension of the particles of these specimens was varied from 13 to 75 p. Several types of nucleation sites of differing potency were fbund to be operative in the nucleation process, but it could not be determined whether these sites were on the free surface of the tin particles or within the volume. Assuming that they were on the free surface, the average density of the most potent sites was calculated to be 2.5 to 5.3 x 10' sites per sq cnz through the application of a Poisson distribztion finction to the isothermal data. Analysis of the temperature dependence' of the rate constmts at a given fraction transformed suggests that the active sites are regions of higher free energy and not catalytic interfaces. Appreciable induction periods were observed at the lower temperatures of transformation. Experimental studies1 of solid-solid phase transformations have led to the belief that the new phase nucleates at structural imperfections. The purpose of the present work was to learn more about the mechanism of nucleation in solids and the nature of the singularities at which nucleation occurs. In this investigation nucleation rates in the isothermal transformation of gray to white tin were measured by an X-ray diffraction technique using essentially monodisperse powders of gray tin. This particular phase transformation was chosen for study because it presented fewer experimental difficulties than most others. The experimental temperature-control problems were minimal because the two phases coexist in equilibrium at 13.3"C, and measurable transformation rates occur at temperatures only slightly above room temperature. The growth rate of the P phase into the a2 is sufficiently fast to make the measured transformation rate equivalent to the nucleation rate, provided that the particle size of the samples is small enough; for the experimental temperatures used in this study, the particle diameter must be less than 100 p. EXPERIMENTAL TECHNIQUE The P tin used in this study was obtained from Capper Pass and Son Ltd., North Ferriby, Yorkshire, England, and was of 99.999 pct purity. It was transformedS to the a phase and ground into a fine powder in an agate mortar. This powder was separated by a Roller air classifier into seven fractions whose dimensions, as determined by microscopic measurement of many thousands of particles, are given in Table I and whose distribution of size within each fraction is given in Figs. 1 and 2. The shape of the particles was roughly that of an oblate spheroid,

Jan 1, 1964