Search Documents

By Frederick N. Rhines, Robert F. Mehl

IT has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick's law (equation 1 below), ‡ in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick's law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Zedele and of Zedele.§ These data are essentially for one temperature alone and do not furnish any information on the variation of the activation heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a singles olid solution field. 11 Much of the argument concerning the properties of metals that determine D and Q has been drawn from data in which variations of the quantities with concentration are unknown, for these data have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concentrations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By George Lehman

THE Inspiration Consolidated Copper Co. had an orebody at Miami, Ariz., of close to 100,000,000 tons of low-grade copper ore, and the method of mining this ore most profitably was of great importance. The selection of a method was practically limited to a "top-slicing," a "shrinkage-stope" or a "caving" method. The "top-slicing" method would give a high extraction of the developed ore, at a high mining cost, and the ?shrinkage-stope" or "caving" methods ) a lower extraction of, the developed ore, at a lower mining cost. ORE-DRAWING TESTS To decide on the method to be used it was necessary to know about what extraction of the ore could be obtained by the "shrinkage-stope" or "caving" methods. As no definite information regarding the question was available at the time, C. E. Mills, the general manager, thought that some information could be obtained by experimenting in drawing ore, covered with capping, from an experimental box. Some work had already been done along these lines by W. C. Browning for the Inspiration Copper Co. and by myself for the Live Oak Development Co. The idea was to represent as nearly as possible, in the experimental box, the conditions within an area of caved stopes of caved ore all ready for drawing. That is, the area was supposed to represent a semibroken mass with the capping above it in the same condition and ready to follow the ore downward as it was drawn out of the chutes under the ore. To represent the above condition, in the experimental box, crushed ore from the mine was placed in it to a given height, and red barren capping from the mine was placed on top of the ore.

Jan 9, 1916

By W. Spencer Hutchinson

The experiments described in this paper were undertaken primarily for the purpose of measuring the quality of work done in screening and sorting in American concentrating-mills for Prof. Richards' work on Ore-Dressiag. For this purpose a series of samples of screened and sorted products was obtained from four different mills, and a plan was devised for sizing these products, and for tabular and graphic representation of the results. The results, together with discussions as to their significance, so far as they serve to interpret the quality of mill-work, have already been published in the above-mentioned work, and it is not the purpose of this paper to duplicate the work, except so far as is necessary to explain and illustrate methods and appliances. The sizing of coarse products was clone by sifting on screens of sheet-metal with round punched holes. These holes ranged in size from 64 mm. to 0.5 mm. in diameter. Below the smaller limit, punched metal, suitable for this work, was not obtainable, and the sizing was carried on by sifting on woven wire-sieves. The finest woven wire-cloth obtainable gave a hole 0.073 mm. square, and the finest silk bolting-cloth pave a pentagonal hole with an average diameter of 0.069 mm. Even these very fine screens served no useful purpose in sifting certain of the very fine classifier-products, of which all, or nearly all, passed through the finest screen. A new adaptation of a method of settling and decantation with water in beakers was therefore worked out, and by this means the sizing mas carried down to grains of a diameter as small as 0.012 mm. Description of Apparatus and Manipu1ntion.—Sieves of sheet-metal with round punched holes were used as far as practicable, chiefly because, as already explained, the primary object of the experiments was to test mill-work, and the mills had all used

Jan 1, 1905

By A. C. Bulnes

This paper applies the methods of statistical analysis to the interpretation of core analysis data of dolomitic limestone from the San Andres formation at Wasson and the Clearfork formation at Fullerton. Probability relationships are shown to connect the porosity and the permeability and the porosity and the fluid saturation. For example, the porosity-permeability relationship expresses the probability that a sample of porosity,f, will or will not be permeable. The over-all porosity frequency distribution of the reservoir together with the frequency curves of permeability (one for each class interval of porosity) provide a precise basis for computing the weighted average productive porosity of the reservoir for any assigned value of the minimum productive permeability. The probability that the permeability of a core specimen from Fullerton will exceed a given value appears to be dependent on the percentage porosity of the specimen, its void structure type (i.e., porosity in the qualitative sense), and the given value of the permeability. If continuous profiles of void structure type and porosity are available together with the appropriate porosity-probability of permability plots, the nes pay thickness may be estimated. The Invasion Index of a well is defined in terms of the porosity and permeability data. This index is suggested as a basis for comparing wells as regards their suitability as fluid-injection wells. Three problems of importance in the exploitation of limestone reservoirs may be stated as follows: 1. The determination of the productive porosity of the reservoir. The productive porosity is defined as f = fPVP/V [II in which Vp, is the volume of the reservoir that is sufficiently permeable to oil to give up an appreciable fraction of its original oil in place during the economic life of the reservoir; fp, is the arithmetic mean porosity of the permeable volume v*, and V is the total volume of the reservoir. 2. The determination of the number of feet of oil-bearing porous rock that will produce at a commercial rate into the well bore; i.e., the net pay thickness. 3. The choice of fluid-injection wells in a secondary recovery program. The ultimate recovery of the reservoir is proportiona1 to the productive porosity. The productive capacity of the well is proportional to the net pay thickness. The principal purpose of this paper is to show that the methods of statistical analysis when applied to core analysis data of dolomitic limestones offer a useful approach to the solution of these three problems, as well as others of importance in reservoir engineering. The use of these methods was suggested by the work of Jan Law.1

Jan 1, 1946

By A. C. Bulnes

This paper applies the methods of statistical analysis to the interpretation of core analysis data of dolomitic limestone from the San Andres formation at Wasson and the Clearfork formation at Fullerton. Probability relationships are shown to connect the porosity and the permeability and the porosity and the fluid saturation. For example, the porosity-permeability relationship expresses the probability that a sample of porosity,f, will or will not be permeable. The over-all porosity frequency distribution of the reservoir together with the frequency curves of permeability (one for each class interval of porosity) provide a precise basis for computing the weighted average productive porosity of the reservoir for any assigned value of the minimum productive permeability. The probability that the permeability of a core specimen from Fullerton will exceed a given value appears to be dependent on the percentage porosity of the specimen, its void structure type (i.e., porosity in the qualitative sense), and the given value of the permeability. If continuous profiles of void structure type and porosity are available together with the appropriate porosity-probability of permability plots, the nes pay thickness may be estimated. The Invasion Index of a well is defined in terms of the porosity and permeability data. This index is suggested as a basis for comparing wells as regards their suitability as fluid-injection wells. Three problems of importance in the exploitation of limestone reservoirs may be stated as follows: 1. The determination of the productive porosity of the reservoir. The productive porosity is defined as f = fPVP/V [II in which Vp, is the volume of the reservoir that is sufficiently permeable to oil to give up an appreciable fraction of its original oil in place during the economic life of the reservoir; fp, is the arithmetic mean porosity of the permeable volume v*, and V is the total volume of the reservoir. 2. The determination of the number of feet of oil-bearing porous rock that will produce at a commercial rate into the well bore; i.e., the net pay thickness. 3. The choice of fluid-injection wells in a secondary recovery program. The ultimate recovery of the reservoir is proportiona1 to the productive porosity. The productive capacity of the well is proportional to the net pay thickness. The principal purpose of this paper is to show that the methods of statistical analysis when applied to core analysis data of dolomitic limestones offer a useful approach to the solution of these three problems, as well as others of importance in reservoir engineering. The use of these methods was suggested by the work of Jan Law.1

Jan 1, 1946

By R. B. Muter, W. C. Grady, T. D. Wheelock, D. G. Chedgy

INTRODUCTION Topics of special interest, such as preparation plant flowsheets and noise pollution, are described in this chapter along with a discussion of non- state-of-the-art processes such as chemical cleaning, high intensity magnetic separation, and bacterial oxidation. PREPARATION PLANT FLOWSHEETS by RICHARD B. Muter In determining the layout or combination of unit operations to be utilized in a modern preparation plant several factors must be taken into account.

Jan 1, 1979

By V. H. Wilhelm

In contrast with the previous year's activity, the California oil industry for 1938 showed a decrease in drilling, market demand, and discovery of new oil reserves, although there was an increase in oil production. Although additions to reserves from new fields and extensions were less than withdrawals during the year, reappraisals of discoveries in 1937 added to new discoreries during 1938 amounted to over 300,000,000 bbl. The following comparative statement shows the important changes in various phases of the industry: Throughout the year the storage situation became progressively more acute, owing principally to less Pacific foreign demand, and increased potential from drilling the newly discovered fields and pools (Fig. 1). California storage increased approximately 32,000,000 bbl. during 1938, most of which (approximately 18,000,000 bbl.) was heavy crude and residuum. The market demand for the year was around 600,000 bbl. per day. Because of the trend toward Diesel power for heavy transportation, the non-gasoline-bearing crudes arc fast becoming a drug on the market. New discoveries were instrumental in increasing the potential production of the state from 1,076,000 bbl. per day in January to an all-time high of 1,420,000 bbl. per day at the close of the year; although the indicated reserves of these new discoveries were not equal to the yearly withdrawal of 249,000,000 bbl. As of the end of 1938, the state was voluntarily curtailed about 58 per cent. As a result of prospecting during the year, six new fields were discovered, three fields were extended, and deeper zones were reached in five of the older fields.

Jan 1, 1939

By V. H. Wilhelm

In contrast with the previous year's activity, the California oil industry for 1938 showed a decrease in drilling, market demand, and discovery of new oil reserves, although there was an increase in oil production. Although additions to reserves from new fields and extensions were less than withdrawals during the year, reappraisals of discoveries in 1937 added to new discoreries during 1938 amounted to over 300,000,000 bbl. The following comparative statement shows the important changes in various phases of the industry: Throughout the year the storage situation became progressively more acute, owing principally to less Pacific foreign demand, and increased potential from drilling the newly discovered fields and pools (Fig. 1). California storage increased approximately 32,000,000 bbl. during 1938, most of which (approximately 18,000,000 bbl.) was heavy crude and residuum. The market demand for the year was around 600,000 bbl. per day. Because of the trend toward Diesel power for heavy transportation, the non-gasoline-bearing crudes arc fast becoming a drug on the market. New discoveries were instrumental in increasing the potential production of the state from 1,076,000 bbl. per day in January to an all-time high of 1,420,000 bbl. per day at the close of the year; although the indicated reserves of these new discoveries were not equal to the yearly withdrawal of 249,000,000 bbl. As of the end of 1938, the state was voluntarily curtailed about 58 per cent. As a result of prospecting during the year, six new fields were discovered, three fields were extended, and deeper zones were reached in five of the older fields.

Jan 1, 1939

By W. A. McCurdy, Joseph W. Leonard, William F. Lawrence

INTRODUCTION Utilization from the Point of View of the Preparation Engineer The primary interest of the coal preparation engineer is in process design, operation, and maintenance to produce an acceptable product that can be sold at the greatest possible profit. Because of emphasis upon these interests, attention to other potential values of coal is sometimes neglected. The intent of this chapter is to alert the preparation engineer to the utilization possibilities of the product as well as the tributary coal flow moving through a modern coal preparation plant. The basis for any unrealized potential derives directly from the coal seam itself. Most coal seams consist of coal bands and benches sandwiched together in layers that differ visually from each other in physical structure and luster. Randomly selected physical and chemical ranges determined from layers of coal in a single seam can easily differ by as much as 30 Hardgrove grindability indices, 0.30 of a specific gravity point, 20 percentage points of ash, 6 percentage points of dry volatile matter, and 10 percentage points of total su1fur.l Similar wide variations exist for calorific value, seam moisture content, and, undoubtedly, for any other conceivable coal test parameter that might be used for comparative purposes. These observations all point to the long-established fact that coal is not homogeneous, as conventional analytical methods might tend to indicate, but is instead a highly heterogeneous substance.

Jan 1, 1979

By G. O. Hiers

THE object of the experiments reported in this paper is to determine the eutectic composition of copper and tin and to determine the location of the part of the liquidus line immediately above the eutectic composition in copper. Three methods were used in the investigation: (1) the method of dissolving copper in a bath of molten tin at constant temperature, with the idea that when the bath was saturated with copper its copper content, by analysis, together with the temperature at which the saturation took place would locate a point on the liquidus line (2) the method of the differential cooling curves, and (3) the method of microscopic examination. This paper is principally concerned with the results of the last two methods mentioned. The results of the first method, that of dissolving copper in molten tin, did not agree with the .results of Miller,1 by the same method, nor with the results of other investigators by other methods, nor yet with the results of the cooling-¬curve experiments and microscopic examination reported here.

Jan 1, 1929

By Herbert R. Hanley

THE One Hundred and Twenty-sixth meeting-of the Institute, held in San Francisco, Sept. 25 to 29, 1922, was a success in every way. Character-istically, San Francisco presented climate suited, to the occasion, while the Committees on Arrangements left nothing undone that would contribute to the interest and entertainment of the members and their wives. There was a registration of over 230, and all sections, save three, were represented. In the technical meetings, under the leadership of Albert Burch in the mining session and C. W. Merrill in the milling session, the greatest interest was manifested in ore-hunting geology and modern ore-dressing methods. The general geologic phase developed numerous discussions and had for its aim the study and correlation of known data and the application-of these to the finding of commercial orebodies. The geologic features of the Comstock and their significance to the development of the present orebodies were discussed. This brought out matters of much technical interest as well as those of romantic nature in the history of the early life of that camp. The profitable application of modern milling methods to ores, non-commercial a short time ago, was discussed with much interest. The recent work on the Comstock ores occupied a conspicuous part in these discussions. Basic principles delineated by mathematical study of mechanical devices for the milling of ore came in for a prominent part in the program as well as the physical-chemical side of the processes devised for the winning of precious metals as a profit.

Jan 11, 1922

By Francis S. Peabody

This paper will not be a technical paper, because, although I have been in the business of mining and selling coal for 30 odd years, I am neither a mining engineer nor a practical miner. If I digress from time to time from my thesis, I must be forgiven by the expert engineers and highly technical gentlemen for whose proceedings this article is written. Waste of the wonderful store of power that the Creator placed at our disposal appears to have been the theory and the basis of our methods of extracting this power—waste from the time the coal is mined to the time it is consumed. Let us consider the prime causes of this wastage which has been the heritage of the coal mining industry. In the early days—about 150 years after " Stone Cole" was discovered in Illinois by Joliet and Marquette, and Father Hennepin noted a "cole" mine on his map—the mode of mining prevalent among farmer landowners, on whose property coal was discovered near the surface or outcropping on the hillsides, was to enter the seam by a shallow shaft or drift into the hillside and remove the coal by wedging it down until a large room was left. The roof without support would fall and our primitive coal operator would then sink another shaft or drive another drift. In these early operations only the large lumps were taken and all small pieces and screenings were left to be covered by the fall of the roof—in fact this condition prevailed in Illinois up to about 1885. Gradually the method of mining changed from the open chamber, to a single entry with rooms turned to the right and left. Later, as the demand for coal increased and the necessity for larger mines became evident, the "room and pillar" system grew to be regular practice. The room and pillar system of mining consisted of starting away from the shaft bottom or drift mouth, with a pair of entries usually 12 to 15 ft. wide and about 30 ft. center to center, one entry being used for the air intake and the other for the return air and haulage; from each entry rooms or chambers were turned, narrow at the mouth and widening

Jan 1, 1918

By J. M. W. Mackenzie, M. H. Buckenam

Flotation experiments using stearic, oleic, linoleic, linolenic, and ricinoleic acids and naturally occuring products rich in these acids as collectors for calcite are described. The results confirm the validity of the rule of Hukki and Vartiainen relating the collecting power and unsaturation of the C18 acids. Reasons for this relationship are discussed and a close relationship between mineral depression and critical micelle concentration is reported. It has long been recognized that the unsaturated fatty acids are in general superior flotation collectors to their saturated homologues. Whereas earlier workers concentrated on saturated and monoethe-noid acids, recent investigations have centered on oleic, linoleic, linolenic, and the substituted mono-ethenoid acid: ricinoleic. From studies of the collecting properties of palmitic, oleic, linoleic, and linolenic acids on ilmenite, rutile, hematite, and magnetite, Hukki and Vartiai-nenl concluded that the collecting power of fatty acids increased with unsaturation of the hydrocarbon chain. Sun, Snow, and Purcel12 investigated the collecting properties of unsaturated fatty acids as collectors for phosphate ores and concluded that the collecting power increased with increasing unsaturation of the hydrocarbon chain up to two double bonds and that further unsaturation decreased the collecting power. More recently Sun3 studied the collecting power of the C18 fatty acids stearic, oleic, linoleic, and linolenic on 37 minerals. The results of these experiments with a few exceptions showed that the collecting power of the acids increased in the order stearic, oleic, linoleic, and linolenic. The relative collecting powers of linoleic and linolenic acids were in many cases altered by the cleanliness of the mineral surface prior to flotation. Sun concluded that linolenic acid may become oxidized by atmospheric oxygen during flotation, a reaction which would reduce its effectiveness as a collector. This deduction is supported by Gaudin and Cole4 who concluded that oleic and linoleic acids do not undergo appreciable oxidation of the double bonds during flotation but that the linolenic acid double bonds are measurably affected. The most complete investigation on the influence of hydrocarbon chain unsaturation on the collecting properties of fatty acids is that of Kivalo and Lehm~svaara.~ These workers using linolenic acid of a higher purity than Hukki and Vartiainen showed that this acid was superior to oleic and linoleic acids as a collector for magnetite. They also found that ricinoleic acid was a more effective collector for this mineral than the other acids investigated, an observation particularly apparent at high collector concentrations. Seeking to explain the superiority of the unsaturated acids these authors considered the effects of critical micelle concentration, surface activity, hydrolysis, and cross sectional area of the hydrocarbon chain in relation to unsaturation. Using what, according to the results of Caviere are erroneous surface tensions of the soap solutions of these acids, they concluded that the surface activity decreases and the critical micelle concentration increases with increasing unsaturation. In view of the data of Cavier, whose results show that surface activity of these soaps increases with unsaturation, the deductions of Kivalo and Lehmusvaara are open to criticism. The degree of hydrolysis of the soap solutions as measured by Kivalo and Lehmusvaara decreases as the unsaturation of the fatty acid increases, a result which helps to explain the superiority of unsaturated acids as collectors. In view of the superiority of unsaturated acids as collectors for many minerals, attention has been directed towards the utilization of fatty acid raw materials such as tall oils and linseed oils which contain considerable quantities of these acids. This paper describes test work to determine the effect of unsaturation of the hydrocarbon chain on the collecting properties of fatty acids on calcite, and includes comparable test work using natural products rich in unsaturated acids. TEST WORK Reagents: The pure fatty acids used were oleic, linoleic, and linolenic. Of these, oleic was supplied by British Drug Houses Ltd. and the others were produced by the Hormel Inst. When not in use these

Jan 1, 1961

By Peter J. Szabo

INTRODUCTION The time period from the detailed feasibility study to the post investment audity usually ranges from three to eight years depending upon the nature of the mining project considered. It is the only after the post investment audit that we know the adequacy of the assumptions made concerning operational risk assessment in the detailed feasibility or acquisition economics. The post investment audit results from numerous mining projects can best be described by a verse by John Greenleaf Whittier's Maaud Muller. It reads "For all sad words of tongue or pen the saddest are these 'It might have been!"' Dissecting the negative results of numerous mining projects we find faulty assumptions concerning markets, geology, capital investment and operational risk assessment. Although in hindsight many of these assumptions could have been considered impossible or impracticle to have forecast with any degree of certainty, we find that refined assumptions concerning operational risk assessment could have been made with only a modicum of additional "Due Diligence". Anyone who invests in a mining property should employ a much higher discount rate of future cash flow, (usually in the minimum range of 25%-30%), than he would expect from such safe investments as Treasury Bills or high grade Utility Bonds. The nature of this steep discount translates to a large uncertainty concerning the timing and actualization of assumptions contained in the detailed feasibility study. We must remember that when a project gets beyond 20 years, any contribution to the value of the project of cash flow is minimal due to the nature of the discounting process. Thus for each full or partial day lost in the development or early operation stage of a project, the financial impact will be greater than similar lost days later on in the project. Adequate operational risk assissment is particularly critical when bidding on competitive tenders for coal deposists in remote locations such as the Bowen Basin in Queensland, Australia. Because of the market attractiveness of these coal deposits for supplying end users in the Far East, Middle East and Europe, state governments require competitive tender biddings via the Authority to Prospect process. Front end bonuses and super royalty payments must be commited before the actual mining conditions are known. Time to submit firm offers from the actual request for proposal vary from 90 to 120 days. Thus any operational risk assessment must be detailed, realistic and reflective of the actual project. When one searches the literature, one finds limited qualitative data on operational risk assessment in valuation papers. Usually this facet of valuation takes a secondary role to such areas as reserves, markets, and environmental considerations. When one comes to the question of operational risk assessment more often than not one finds the use of "rules-of-thumb", such as tons per man shift, average production, average seam height, etc., are used to forecast results on which banks and other financial institutions are required to make investment decisions. Because of the extremely competitive environment of the 1970's and 1980's numerous financial institutions approved loans without adequate "Due Diligence", and are currently paying a steep price in terms of non performing loans and charge offs. One must always remember that each operation is unique with its own characteristic

Jan 1, 1985

By J. J. Thomas, J. H. Nead

This investigation was undertaken to determine, if possible, the relation between static and dynamic tensile tests as measured by the work required to break test specimens slowly, in a tensile testing machine, and rapidly, by means of a falling weight. It was hoped that the investigation would throw some light on the role played by ductility under different rates of application of load. In problems of design, it is usually assumed that the moduli of elasticity of all steels are equal; viz., about 30,000,000. The stress-strain diagram within the elastic limit is a straight line, as shown in Fig. 1, where OA is the curve of a hard steel and OB that of a soft steel. If the modulus of elasticity is constant, as assumed, the slope of the line OC

Jan 1, 1922

By J. H. Nead, J. J. Thomas

This investigation was undertaken to determine, if possible, the relation between static and dynamic tensile tests as measured by the work required to break test specimens slowly, in a tensile testing machine, and rapidly, by means of a falling weight. It was hoped that the investigation would throw some light on the role played by ductility under different rates of application of load. In problems of design, it is usually assumed that the moduli of elasticity of all steels are equal; viz., about 30,000,000. The stress-strain diagram within the elastic limit is a straight line, as shown in Fig. 1, where OA is the curve of a hard steel and OB that of a soft steel. If the modulus of elasticity is constant, as assumed, the slope of the line OC

Jan 1, 1922

By J. S. Ross

Few Canadians realize the role of their domestic industrial minerals industry because it is over-shadowed in production value by a large metallic minerals industry. But since 1960, Canada has had a reasonably well balanced, mature industrial minerals industry; and although the nation's sparsely scattered population has not been able to support an industrial minerals industry in a manner comparable to the domestic and foreign support given the metal mining sector, Canada is, nevertheless, exporting large quantities of higher priced nonmetallic minerals. Production of many of the basic minerals had been firmly established long before 1960, but it was not until the late 1950's that the output of cement, salt, titanium dioxide pigment and slag, sulfur, gypsum and sodium sulfate reached relatively high levels. Shortly after 1960, the significant potash and lithium chemicals industries were established and their effect is just now being realized.

Jan 11, 1964

GENERAL GEOLOGIC DESCRIPTION The mineral deposit of this case study can be described as a "typical" porphyry copper deposit of the southwestern USA and northern Mexico mineral province. The copper mineralization is related to Laramide age intrusives of intermediate composition which have been intruded into older, mostly crystalline, host rocks. Post Laramide deformation and faulting have subjected the deposit to erosion, leaching, and enrichment processes, which have created a secondarily enriched chalcocite zone. Later basin and range faulting down dropped the ore zone, resulting in deep burial beneath late Tertiary conglomerates and gravels, thus preserving the deposit from further erosion and oxidation. Lower grade chalcopyrite mineralization constitutes the primary zone underlying the enriched blanket. MANAGEMENT OF SAMPLE DATA Sample data were obtained from exploration diamond drill holes that were collared vertically and drilled with surface rigs. Most of the holes were surveyed downhole and found to deviate significantly from the vertical. The data were keypunched from original drill hole logs to formats as described in Chapter 6. Three types of cards were prepared: 1) A heading card containing the following information: [Project Name Coordi-in_ Hole Collarnates Bear-clina-Total ID Northing Easting Elevinglion Depth] 2) Individual record cards following each heading card with the following information: [SampleMin. Zone interval Assay Fields Leached (enriched ID From-ToTotal Cu Oxide Cu primary)] 3) Where downhole survey data were available, a card was punched for each downhole survey point. The card image looked very much like the heading card, followed immediately after the heading card, and contained the following information: [Hole Sur Point Sur Point Sur Point ID Bearing Inclination Depth] The keypunched data were then processed by the drill hole survey program producing a record file which contained information as follows: [Line 1. Project Name Date Assay Field Identifiers Line 2. Hole ID Northing Easting Elevation Bearing Inclination Number of Samples Line 3 through N+ 2 (where N equals the number of samples in the hole) Top Min. of Min. Zone Zone Sample Sample Coordinates Sample Assays Leach InterLength Northing Fasting Elev Total Cu Oxide Cu (etc) face] MINERAL BOUNDARY PROBLEM AND TREATMENT According to the geologic description, at least three mineral zones are present within the ore limits, as well as fault boundaries and a buried topographic surface, each of which have to be considered. The interfaces of the various mineralogical and geological boundaries were identified as accurately as possible in each drill hole by the project geologist, the location of the interface was surveyed in the computer program in association with the nearest sample intercept to the interface (note last field of line 3). Thus, the boundary is represented as a point in 3D space at each intersecting drill hole. The linear interpolation (LINTERP) program then searched the last field of the surveyed record to find the top of each mineral zone, or geologic boundary, and read the coordinates associated with that sample point. The program then used the coordinates to compute an interpolated surface between all existing data points as described in Chapter 11. A contour map was plotted for each of the computed surfaces and reviewed by the project geologist. Where the surfaces were poorly defined due to lack of real drill hole information, the geologist, at times, inserted a "pseudo" drill hole intercept according to his best judgment and feeling for the configuration of the surface, and such points were entered into the data stream for LINTERP. When the project geologists were satisfied that they had obtained

Jan 1, 1980

By Robert Lowrie

Nine intermetallic compounds were tested in tension at various temperatures. Seven exhibited extensive plastic deformation at elevated temperatures. Correlations of tensile strength and elongation are attempted with melting (decomposition) temperature, valence electron configurations of the component elements, heat of formation, crystal structure, density, and volume decrease accompanying compound formation. A LTHOUGH intermetallic compounds have been -tX known for many years, the study of their mechanical properties, particularly in tension, is just beginning. The problem has been unattractive because of the well-known, erratic behavior of brittle materials tested in tension. The strong influence of surface or internal flaws as stress raisers in non-ductile materials and the effect of eccentricity of loading in superimposing bending stresses on the state of tension in the specimen are extremely difficult to mitigate and impossible to completely eliminate. Thus, tensile properties determined for brittle materials, such as intermetallic compounds at temperatures low in comparison to their melting points, are at best only general guides to the values to be expected in an ideal test of a perfect specimen of the material. It is, nevertheless, surprising that apparently no attempt was made to follow up the pioneer work of Tammann and Dahl1 in this field. Working with crude apparatus, these investigators succeeded in showing unequivocally that at temperatures sufficiently close to their melting points (from 75" to 400°C for the compounds tested) intermetallic compounds did exhibit plasticity. This was indicated by the appearance of slip lines on the surface of the specimen. No observations of strength were made in these tests, which were of a compressive or indentation type. Rossi2 in 1932 attempted to study the physical and mechanical properties of single crystals of a group of intermetallic compounds. However, he was able to prepare only one material, Cu2Z8,, in the form of large, defect-free, single crystals. Thus, he was able to report only the relative fragility of the compounds at room temperature. He reported one compound, Ag,Zn,, to be somewhat plastic at room temperature and Cu,Si to be friable, the latter in agreement with results reported herein. Although test results are available only in classified literature, it has also been announced that MoSi, possesses some ductility at elevated temperatures." In 1948 and 1949 Savitskii and Savitskii and Baron -ublished their work on the hot extrusion of Mg-Zn, Al-Mg, and Cu-Zn compounds. Under the favorable state of stress existing for this process MgZn, MgZn,, MgZn,, ß (Al-Mg), ? (Al-Mg) and 0 (Cu-Zn) could be reduced by amounts up to 90 pct at elevated temperatures. These authors also report that hardnesses of Mg-Zn compounds decrease from room temperature values of about 300 kg per sq mm to 30 to 50 kg per sq mm at 325°C. They found that alloys consisting solely of one Mg-Zn compound were most resistant to softening on heating, mixtures of a compound and eutectic less resistant, and mixtures of two compounds least resistant. The more rapid softening of mixtures of

Jan 1, 1953

By G. R. Love, C. C. Koch

The changes in superconducting properties with aging time have been studied ,for the pecipitation reaction in a Tc-30 at. pct V alloy. Superconducting critical temperature, upper critical field, and relative critical current density were determined by ac susceptibility techniques. Aging produces changes in critical temperature of both matrix and precipitate which can be rationalized by compositional effects. maximum flux pinning (critical current density) occurs at a time during aging when subgrain boundaries are completely decorated with precipitates and the subgrain centers remain precipitate -free. The particular effectiveness as barriers to flux motion of planar defects which enclose regions of low deject density is discussed. THE precipitation of a second phase can dramatically modify the superconducting properties of type I1 super-conductors. According to Livingston and Schadler1 one might expect changes in the primary, secondary, and tertiary superconducting properties of the material. Changes in matrix chemistry caused by precipitation can alter the fundamental superconducting parameters; critical temperature, Tc, and thermody-namic critical field, Hc. The concimitant changes in electron mean free path (reflected in normal state resistivity) can affect the critical fields Hc 1, IIc2, Hc3. Finally, the presence of precipitate particles may hinder the motion of flux lines and may considerably improve the current-carrying capacity in high-field superconductors. The influence of precipitation on superconducting properties has been studied in a number of systems.2 Magnetization measurements have been used to study the influence of precipitates on flux pinning in lead-base alloys by Livingston3 and Evetts et al4 In these alloys precipitates induced magnetic hysteresis and flux trapping. The amount of hysteresis increased with the volume fraction of precipitate and decreased with coarsening of the precipitate. Jn an Al-Zn alloy5 and an A1-Ag alloy6 the initial precipitate size was presumably smaller than a coherence length and coarsening increased magnetic hysteresis5 and critical current density.6 The influence of precipitation on superconducting properties has also been studied in several of the commercially interesting Ti-Nb7-10 and zr-Nb11 alloys. The maximum in critical current density for these alloys was confined to a narrow range of either isothermal aging time" or isochronal aging temperature7 during the precipitation reaction. Thus, experimental evidence and theoretical considerations suggest there is an optimum precipitate size, spacing, and density, and a critical composition with respect to the matrix for flux pinning. What these "optimum" values might be and the relative importance of each is still not clear, although a few generalizations can be made. It is generally accepted1' that particle sizes smaller than the coherence length or larger than the inter-flux line spacing are poor pinning centers. In high Hc2 materials, precipitate sizes for maximum values of critical current density lie in the range of 50 to 2000Å,9,7 and there are indications that increasing dissimilarity between precipitate and matrix produces increasing pinning force.13 Because of several interesting features of the aging reaction in a Tc-30 pct V alloy, we have chosen to study the influence of precipitation on the superconducting properties of this alloy. The physical metallurgy14 and a survey of the superconducting properties" of the Tc-V alloy system have been reported. The Tc-V phase diagram is presented in Fig. 1. At 1500°C the Tc-30 pct V alloy is in the single phase 6 field. Samples quenched from the 6-phase field have a CsCl structure X-ray diffraction pattern at room temperature and it has been proposed that the 6 structure is closely related to the bcc lattice.14 When held isothermally below the eutectoid temperature, 115O°C, the 6 phase decomposes into the CsCl and hcp phases.

Jan 1, 1970