Search Documents

By Michael Perch, Charles C. Russell

Nearly 95 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69,9, and in 1938 it was 61.3, To produce a net ton of pig iron 1959 lb. of coke was required in ,1940 and 1760o lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank1 standardized by the American Society for Testing Materials. Although this method of classification has been an American standard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1942

By B. D. Cullity, A. Freda

It is well known that deformation by cold drawing or swaging produces a kind of preferred orientation called fiber texture in metal wires. Such textures have been extensively studied by means of X-ray diffraction, chiefly by techniques in which the diffracted X-rays are recorded photographically. This paper describes some results obtained with a new method, involving the use of a diffractometer. X-RAY METHOD Since the pole figure of a material having a fiber texture is symmetrical about the fiber axis, there is no need to present the entire pole figure. Instead, texture data can be summarized by means of a curve showing the variation of pole density along any meridian of the pole figure, if the north-south axis of the latter is made parallel to the fiber axis. The position of a pole on the meridian is specified by the angle 9 between the pole and the fiber axis (wire axis). The X-ray method1 used here to measure pole density as a function of 9 actually consists of two methods, referred to as A and B. In method a, X-rays are reflected from the wire surface. Pole densities can be measured by this method from O = 90 deg down to a limiting value which is dependent on the Bragg angle 8 and is typically of the order of 30 to 40 deg. Method B involves diffraction from the wire cross section and covers a range of 0 values from 0 up to an angle sufficient to overlap the measurements made by method A. By a combination of the two methods, a complete pole-density curve can be obtained. However, method A alone, which requires no specimen preparation other than etching, can often reveal enough of the pole-density curve to provide complete information about texture components. Both methods require that the measured diffracted intensities be corrected for changes in absorption and diffracting volume with changes in 9. A11 intensities I reported in this paper are corrected diffracted intensities; they are propor-

Jan 1, 1960

By Harry C. Gatos, Frank J. Bachner

It was shown through high-pressure experiments that tin loss by volatilizatim is necessary for the degrada-tion of the superconducting transition temperature of Nb,Sn associated with high-temperature annealing. Crystallochemical analysis of the degraded Nb3Sn showed that it constitutes a new phase with ordered niobium-site vacancies, created by the migration of niobium atoms to vaccnt tin sites. This new phase was found to form when 4 pct Nb-site vacancies were present. It has a transition temperature of 6'K and a lattice parameter of 5.283A. A similar degradation effect was observed in Nb,Al. Its superconducting transition temperature dropped from 16.5" to 8" K following a high-temperature annealing. The superconducting temperature degradation in these 0-tungsten structure compounds is attributed to the disruption of the interchain d bonding by the periodic interruption of the niobium atom chains. By annealing the degraded Nb, Sn at 1000 C in nitrogen its normal superconducting behavior is restored most likely due to the incorporation of nitrogen atoms causing the elimination of the ordered vacancies. HANAK et al.' have observed low superconducting transition-temperature values (T, - 9"K) in some NbsSn samples deposited from the vapor phase. They attributed such low T, values to disorder in the 0-tung-sten structure. Much lower T values (down to 5.6"K) were reported by Reed et al.zC for NbsSn samples annealed at high temperatures. These authors also attributed this degradation effect to disorder (random occupation of the A and B sites by niobium and tin) but pointed out that such disorder could be brought about (by high-temperature treatment) only in samples containing niobium in excess of the stoichiometric composition NbsSn. Both groups reported that the normal superconductivity behavior could be rever-sibly restored by appropriate heat treatment. Courtney et al., also found that degradation in NbsSn requires excess niobium brought about by the loss of tin during the treatment. However, these investigators proposed that the degradation is due to niobium-site vacancies resulting from the migration of the niobium atoms to the vacated tin atom sites. They did not consider the reversibility of the effect. The present study attempts to establish the nature of the above degradation phenomenon. EXPERIMENTAL PROCEDURES All compounds prepared for this investigation were made from the powders or filings of the elements which were intimately mixed, cold-pressed into a cylindrical pellet at approximately 50,000 lb per sq in., and then submitted to the desired heat treatment. The samples annealed under high pressure were placed in a MgO sample container which was mounted in a pyrophyllite tetrahedron designed for a tetra-hedral-anvil press. Details of the experimental arrangement are given elsewhere. This setup allowed heating at 1800°C or above under pressures in excess of 30kbars for 3 hr. The samples annealed in a vacuum were prepared in a high-temperature vacuum furnace which could reach temperatures up to 2400°C under a pressure of 2 x lo-' Torr. For annealing in a reactive atmosphere, a quartz tube was placed in a clamshell furnace and the desired gas ambient passed through the tube. Lattice parameters were determined using a Debye-Scherer 114.6-mm camera. Cohen's method, programmed for the IBM 7094 computer, was used to calculate the lattice parameter from the measured d spacings. X-ray integrated intensity measurements were made on several samples. These samples were ground to -400 mesh and the powder mixed with a solution of collodion in amyl acetate. The mixture was poured into a depression milled in a bakelite disc. When the mixture dried, the surface of the disc was ground flat leaving a diffraction surface defined by the face of the disc. The disc was mounted in a Philips rotating specimen holder which allowed the rotation of the sample in the plane of the diffraction surface and the integrated intensity measured using a scintillation counter and a pulse-height analysis sys-tem. The superconducting transition temperatures were determined by means of self-inductance techniques.' EXPERIMENTAL RESULTS AND DISCUSSION The Role of Tin Loss in the Degradation of Super-conductivity. The loss of tin during high-temperature annealing can be effectively suppressed by annealing under high hydrostatic pressures. Accordingly, a series of experiments were performed under pressures of approximately 30kbars. This pressure was the minimum under which high-temperature experiments could be safely performed in the particular pressure apparatus employed. Experiments were also designed to test high-pressure effects on the superconductivity behavior of NbJSn. The results of the high-pressure annealing experi-ments are summarized in Table I. All samples were prepared as described earlier. They were reacted and homogenized at 1000°C for 24 hr under argon at-

Jan 1, 1967

By Nathan C. Rockwood

LIME is a very general term applied to products of limestone, in popular treatises often incorrectly, including ground or pulverized limestone used in agriculture. When used without qualifying adjective, the term usually means burned or calcined limestone, or quicklime, or calcia. The corresponding calcined product of magnesite is magnesia. If the calcined rock is relatively pure calcium carbonate, the resulting lime is a "high-calcium" lime; if the rock is dolomite, or a combination of calcium and magnesium carbonates, the lime is a "dolomitic" or a "high- magnesium" lime. There are various grades in between, depending on the percentage of magnesium carbonate and other ingredients in the raw rock. For some industrial purposes only high-calcium limes are suitable; in other processing-as, for example, neutralizing acid wastes -the relative percentages of magnesium and calcium carbonates in the raw material are not important. Limestone is burned (roasted or calcined) in furnaces known as lime kilns by direct exposure to the hot gases and flames. When heated to incandescence, the carbon dioxide content of the rock is expelled, leaving calcium and magnesium oxides, according to the formula usually written: [ ] This thermal reaction is reversible, which requires that the lime be withdrawn from the "calcining zone" of the kiln about as fast as made. Pure calcium carbonate would lose 44 pct of its weight in the calcining process; dolomite, 48 pct. Generally, the lime will retain the approximate size and shape of the piece of rock from which it is made but some few limestones tend to break down into granules or dust. Hence lime (quicklime) comes from the kilns in lumps or granules and normally is packed in water- tight containers in these forms, or is pulverized after calcination.

Jan 1, 1949

By D. J. Weintritt, J. C. Cowan

Methods of studying oilfield mineral .scale deposition in the laboratory do not work for barium sulfate because only small nonadhering crystals ore formed. On the other hand, barium sulfate scale found in down-hole or surface equipment is strongly adhering and may contain very large crystals. Results suggest that most of the difference derives from the extremely low .solubility of barium sulfate. Firm adherence of scale and the consistent development of oriented crystals 100 microns and larger suggest a relationship between scale adherence and crysta1 growth. Data from this study indicate some reasons for barium sulfate's occurring as a deposit in oilfield waters. The unique characteristics as well as the associative properties of barium sulfate scale as related to calcium carbonate and calcium sulfate ere shown. INTRODUCTION The first observed deposition of barium sulfate scale in oilfield production equipment is unknown but probably coincides closely with the beginnings of the oil industry itself. Moore' described barite oolites in some producing wells in the Saratoga field, Tex., in 1914. Currently, positive identification of barium sulfate deposition is recorded in most of the major oil-producing areas of the United States. As efforts continue to identify the composition and functions of the materials found in scale deposits, the geographic and economic importance of the part played by barium sulfate will become even more important. This belief is based on the following Facts. 1. Many oil fields in the U.S. are in or entering their mature phase and the volume of produced water is increasing; thus, the cumulative effects of low-solubility minerals become more significant. 2. Secondary recovery techniques and increased emphasis on waste disposal systems require controlling the behavior of all constituents of water to prevent formation plugging. 3. The more general use of instrumental analysis has reduced the time and improved the accuracy of complete scale and water analysis. 4. Once formed, barium sulfate scale is resistant to present methods of chemical removal; therefore, costly mechanical methods are necessary. Thus, new methods of prevention and control will require specialized chemical techniques and better knowledge of the causes of scaling. Consider the results of some simulated field deposition studies illustrating this need (Fig. 1). The studies utilized a Scale Deposition Test Cell* and each coupon was exposed to 8,000 ml of a 300 me/liter solution of the various types of mineral scale. All tests were conducted at 140F. Only the calcium sulfate and calcium carbonate deposited scale. The solution containing 300 me/liter of barium sulfate exhibited copious amounts of precipitate, but none of the precipitate adhered. The fluids from the effluents were also allowed to impinge on glass slides. Fig. 1 shows the relative adherence of the three types of scale on unetched glass. The barium sulfate failed to deposit in the same manner as the calcium carbonate and calcium sulfate solutions.

By W. H. Herrnstein, J. B. Clark, E. C. Utley, A. J. McEvily

The ratio of the endurance limit (10' cycles) to tensile strength of age-hardened aluminum alloys is approximately 0.3, whereas the ratio for annealed alloys is about 0.5. The lower value for the age-hardened alloys has been associated with the instability of coherent precipitate during cyclic loading, but it has not been definitely established whether this instability is due to overaging or reversion during cyclic loading. The results of the present investigatzon support the reversion viewpoint. In this work specimem of 2024-T4 aluminum alloy were aged for 16 hr at 150°C after cycling for 10 pct of the life at 25.000 psi. These specimens were then tested to failure and exhibzted a marked increase in fatigue life. It is proposed that during the early stages of fatigue in this alloy dislocations cut through the coherent precipitate and bring about the reversion of the precipitate. Subsequent aging at 150ºC induces reprecipitation in the precipitate-free zones so that the weakened regions are strengthened and the fatigue life is extended. It Is recognized that the fatigue strengths of precipitation hardened aluminum alloys are unusually low relative to their tensile strength.'-= This feature is illustrated in Fig. 1 where it can be seen that age-hardened alloys have lower fatigue ratios (the ratio of the fatigue strength to the tensile strength) than those in the annealed or cold worked state. Further, as shown in Fig. 2, the more an alloy is dependent upon precipitation hardening for its total strength, the lower is the ratio of the fatigue strength to the tensile strength. This state of affairs has been associated with an instability of the metastable metallurgical structure of precipitation hardened aluminum alloys during cyclic loading. Evidence2 in support of this view is that the fatigue ratio increases in these alloys as the test temperature is lowered, thereby indicating that thermo-mechanical instability, rather than some other factor such as a non-uniform distribution of precipitate, is the factor responsible for the low fatigue ratio at room temperature. Two mutually exclusive proposals have been ad- vanced to account for this instability. Hanstock has proposed that overaging takes place during cyclic loading, and in support of this view, Broom et a1.2 have indicated that an overaging process might be promoted by the large numbers of vacancies which are created during cyclic loading. The creation of vacancies by radiation4 has been shown to lead to rapid overaging. Hanstockl obtained visual evidence of overaging in an aluminum alloy after cyclic loading, but in this instance it has been pointed ou? that because of the high frequency used (60,000 cpm) the observed effect may have been due to normal high temperature precipitation around energy dissipating cracks. Efforts to discern visual evidence of overaging in this alloy at lower test frequencies were not successful.3 The alternative postulate3 is that reversion takes place during cyclic loading and leads to localized soft spots at which fatigue cracks are readily initiated. Evidence for this process has recently been provided by Polmear and Bainbridge5 who demonstrated metallographically that regions depleted of precipitate were created during cyclic loading of an aluminum alloy. Inasmuch as precipitate particles bordering the depleted region had not grown in size, it was concluded that the solute atoms which had constituted the missing particles had gone back into solution. No mechanism for the reversion process was presented. The present study was undertaken to investigate further the conditions leading to instability during cyclic loading, and to determine whether reversion or overaging had taken place as a result of cyclic loading. BACKGROUND AND TEST PROCEDURE In order to differentiate between the processes of reversion and overaging, rest periods at an elevated temperature, which ordinarily would insure additional precipitation, were used in this investigation. It was expected that after a period of cyclic loading an elevated temperature rest period would result in a decrease in the remaining life of the specimen if overaging were occurring during cyclic loading, whereas in the case of reversion, reprecipitation would occur and the fatigue life would be extended. Such an expectation is based on the assumption that the crack-nucleation phase is a significant portion of the total fatigue life, and that such a treatment is of influence in the crack-nucleation stage and is relatively unimportant thereafter.

Jan 1, 1963

By M. C. Dow

INTRODUCTION BELT conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stonecrushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. GENERAL RELIABILITY It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 1/2 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. LOADING THE BELT It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined conveyor to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1947

By Fulton B. Flick

The micrography and macrography of aluminum and its alloys present certain difficulties. Many of the difficulties attendant on the micrography have been removed by methods developed during the past few years, notably those of E. H. Dix, Jr.1 The development of grain size in aluminum and its alloys may be equally troublesome, yet comparatively little detailed attention appears to have been given to it. Satisfactory reagents are available for the development of such structurcs in ferrous and most non-ferrous metals, but those applied to aluminum and its alloys, i. e., alcoholic or aqueous solutions of sodium hydroxide or hydrofluoric acid are not entirely satisfactory. Hanson and Arch-butt,2 in speaking of these two reagents, state that "These two reagents give fairly satisfactory results, but they sometimes produce badly tarnished surfaces from which the surface deposit is difficult to remove." It has been our experience that neither of these reagents is to be entirely relied on for developing structures suitable for study or photography. This means that when the etch fails to produce satisfactory results the specimen must be repolished, through the 000-paper at least, and then etched with another reagent. This procedure entails a considerable loss of time, and the final results may not be all that might be desired. However, the reagent to be described, although not a panacea for all etching troubles, has improved results so markedly that it is felt that it & worth offering as a grain-size etch generally applicable to aluminum and aluminum alloys. Czochralski3 in 1915 mentioned the application of a solution of 10 to 20 c. c. concentrated hydrofluoric acid in 100 c. c. absolute alcohol, etching in this reagent being followed by dipping in concentrated hydrochloric acid soliltion.

Jan 1, 1925

By N. A. McLeod

BALL wear in wet grinding mills has been the subject of considerable discussion in the last few years. Its importance to millmen is obvious in view of the fact that ball wear may cost from 2 to 4¢ per ton of ore for the more fortunate operators and many times this cost when a refractory ore must be reduced to a fine state of comminution. Consequently, any factual information that may be obtained on the nature of ball wear may be applied to introduce changes leading to lower ball consumption and therefore also to lower costs. In 1940, while employed with the Britannia Mining and Smelting Co., Britannia Beach, B.C., I had occasion to investigate factors that might affect ball consumption. We performed a number of tests, which will be briefly described. These tests originated as a result of changing from a 3 1/2-in. ball to a 2-in. ball of different type of manufacture and were motivated by the desire to obtain the best possible type of 2-in. ball. Our testing was helped by the fact that the company operated a one-ton electric furnace, so that it was quite easy to make steel changes. It should be emphasized at the beginning that these tests produced results that in their general application to milling should be interpreted qualitatively rather than quantitatively. As will be evident in the description of the method used in testing, the balls were subjected to an intermittent batch grinding treatment, which may have produced results in rate of steel wear that may not have an accurate correlation with steel consumption in full-scale mill operation. However, with this fixed and rather arbitrary method of testing, results were obtained that may be of some interest and may stimulate further work on this subject. Unfortunately, owing to pressure of war work, our tests, which we had intended to repeat on a continuous grinding operation, had to be discontinued. METHOD OF TESTING Tests were made in a small cylindrical mill, rotating at 72 r.p.m. Internal dimensions of the mill were 10 1/2-in. dia. by 9 in. The cylindrical inner surface was lined with rubber and the two ends were formed by steel plates. A charge of 2000 grams dry feed and 2000 c.c. of water was added every 2 hr., the mill being drained of pulp before the addition of each charge, by tilting and sluicing with water. The mill was run on afternoon and night shift for daily periods of about 15 hr. total grinding time, and each test lasted from 60 to 150 hr. This batch method of testing involved a higher average pulp temperature in the mill, which undoubtedly affected comparative results in some of the tests. HARDNESS OF BALL VS. WEAR In these tests, special "eutectoid" steel balls were used, some of which were chill-cast and quenched, some sand-cast and quenched, and some sand-cast and annealed to a dead soft condition. The results obtained, using as mill feed an ore containing considerable free quartz and

Jan 1, 1945

By E. J. Ripling

TUBES may be produced by a large number of forming processes, the most common of which will be discussed analytically in this paper. In no case will the stress analysis for any given tube producing process be derived formally for where such analyses are available, they may be referred to readily. Rather, emphasis will be placed on the interpretation of the theory of the different processes, few of which are developed to a state that will allow rigorous mathematical analyses, in an attempt to give a rational description of the effects of the different variables involved in each method. Tube producing methods can be divided into two groups: Those used to form shells, and those used to further work these shells into a shape more suitable for their final use. Among the first group are included roll piercing, extrusion and cupping for seamless shells, and bending with welding for welded tubes. The re-forming processes include sinking, drawing with a plug, and drawing with a rod. Only the plastic forming operations will be discussed here; other forming processes such as casting shells will not be considered. PRODUCTION OF SHELLS Shells for Seamless Tubing Piercing: The extremely important process of forming an axial hole in a billet by oblique rolling never has been analyzed satisfactorily, although a certain amount of experimental work relating to this process has been conducted. There are a number of factors that make piercing difficult to analyze; one of these is the fact that piercing is not a problem in plasticity, but one in fracturing, and the laws of fracturing are even less well understood than those of plasticity. If, however, it is assumed that fracturing occurs on a surface as a result of tensile stresses acting normal to this surface, piercing can be analyzed qualitatively by examining the stresses established in the oblique rolling process. To determine the origin of the tensile stresses that are thought to effect piercing, it will be necessary to know the angular relationships between the maximum stresses that are established in piercing. These angles quite frequently can be determined in a plastic deformation process by an examination of the deformed product. For example, consider the stresses established when a tensile test is conducted on a rectangular cross-sectional specimen of pearlitic steel. When stretched, this material first flows plastically, exhibiting the well-known yield jog on a stress-strain curve. The formation of the slip areas that give rise to the yield jog can be detected during the straining, since these flowed areas cause depressions on the specimen surfaces which can be seen if the surfaces are polished highly. The plastically strained areas also can be found after the specimen has been stretched to a strain not exceeding the yield jog, by sectioning the test piece and. etching these sections with Fry's etch. With this etchant, it is possible to dis-

Jan 1, 1951

By C. H. Mathewson

MicrOscopic metallography has been exploited quite well enough to bring about a very general understanding that the typical metal or alloy is composed of minute crystalline particles blended into a coherent rnicrostructural rnosaic. One does not have to be a specialist in metallography to realize that the properties of such an aggregate are essentially a summation in appropriate form of individual effects derived from the shape, size, placement or orientation and cohesive characteristics of the component particles. It is clearly of great importance to consider the various forms of discontinuity which may occur at the boundaries between these crystalline particles. When a number of particles each possessing the same orderly arrangement of atoms are brought together into a close-fitting system of purely haphazard contacts, not unlike a handful of snowflakes compacted into a snowball, the particles are said to possess random orientation. There are no generally accepted views concerning the arrangement of the atoms or the constitutional reaction between atoms where one crystal meets another, but these contact regions are characterized by strength rather than weakness and it is customary to require the presence of many rather than few boundaries in preparing metal for useful service. Under certain circumstances all of the particles in a metal may be nearly alike in orientation. Other general tendencies of orientation may be associated with particular forms of mechanical and thermal treatment. In contrast with these cases of fortuitous or statistical diversity of orientation, we often find adjacent particles united along a plane which possesses a grouping of atoms belonging equally well to both structures. This, of course, determines a fixed relationship between the two orientatjions and it is always possible to derive one from the other by some form of- rotation or reflection prescribed by the symmetry of the crystal structure under consideration. Particles united in this manner are known as twin crystals although the term refers to the form of association rather than the number of individuals concerned.

Jan 1, 1928

By Milton E. Wadsworth, John N. Ong, W. Martin Fassell

The temperature and oxygen concentration dependence on the reaction of sphalerite in oxygen at pressures from 6 to 640 mm Hg have been investigated in the temperature range 700° to 870°C. Sphalerite has been found to oxidize linearly over this entire temperature and pressure range. At higher rates, considerable self-heating was observed. The dependence of the oxidation rate on the oxygen concentration may be expressed by: Rate = k' where k' is the specific rate constant and 0 = K1[O2]/(1 + KI[O2]), where K1 is the equilibrium rate constant for the adsorption of oxygen on sphalerite. Values of the activation energy and the enthalpy of adsorption were found to be 60.3 and —59.6 kcal per mol, respectively. Data have been presented that indicate conditions under which either a sulphatizing or an oxidizing roast may be obtained. ROASTING processes have been employed in the metallurgy of a great number of basic metals in use today. Until recently, however, little attempt has been made to deduce the fundamental mechanism by which oxidation takes place. Structural changes upon oxidation have been investigated1 = and thorough work has been performed with regard to the reaction products and the thermodynamics of the oxidation reactions. The objective of this investigation was to determine the rate of oxidation of sphalerite and to apply the absolute reaction rate theory in the theoretilcal interpretation of the experimental results." "O Description of Apparatus The apparatus contains the following features: 1—a furnace with gas system, 2—an autographic weighing system, and 3—a temperature control system. Furnace With Gas System—The furnace was mounted by a yoke on each end and was free to travel up and down on steel guide rods, permitting the introduction and removal of samples from the apparatus with minimum difficulty. The furnace was heated by three sections of Kanthal wire wound externally on a zirconia tube and insulated with Fiber-frax. Pure gases or mixtures of gases were introduced into the lower end of the furnace through two flowmeters, a mixing chamber, and a gas-tight sparger, Fig. 1. The gaseous products of the reaction and the unused gases were prevented from escaping to the atmosphere by maintaining a small negative pressure on the system. This procedure permitted air from the outside to enter through the small an-nulus around the quartz suspension fiber and prevented the escape of the internal gases. Autographic Weighing System—The autographic weighing system consisted of an adapted gold balance, a photoelectric circuit, and a weight recorder, Fig. 2. The sample was suspended from one end of the balance beam by means of a platinum chain outside the furnace and a long thin quartz fiber on the inside of the furnace. On the other end of the balance beam, the necessary weights were added to counterbalance the sample. In addition, a calibrated chain was added to the balance which was linked directly to the weight recording unit. Control was effected by means of a photoelectric circuit." A parallel beam of light from a strong source was directed onto a small front-surfaced aluminum mirror mounted in the middle of the balance beam and then to a front-surfaced mirror mounted on the ceiling of the room. The beam was then reflected onto a front-surfaced right prism at a distance of 9 ft from the balance

Jan 1, 1957

By Earl S. Bardwell

The determination of suitable and safe annealing temperatures is one of the most important problems arising in the operation of a copper rolling mill. Certain of the larger mills have worked this problem out for themselves and in these mills the operation has become more or less standardized. In some of the mills pyrometers are used to measure the temperature of the annealing furnaces and careful watch is kept to see that overheating does not take place. In a considerable number of the mills, however, dependence is placed entirely on the judgment of the operator. The almost total lack of literature bearing on this subject seems sufficient warrant for the publication of this paper. ' The discussion of this subject naturally divides itself into two parts: (1) The effect of annealing temperature on physical properties; and (2) changes in the microstructure of refined copper due to cold rolling and annealing. I. The Effect of Annealing Temperature on Physical Properties For the purpose of investigating this phase of the subject six test bars were selected, varying in oxygen content between the limits of 0.036 and 0.070 per cent. The chemical composition of each of these test bars was as follows: Bar Number 1 2 3 4 5 6 Copper + silver...... 99.95 99.92 99.945 99.94 99.95 99.93 Oxygen.............. 0.041 0.070 0.046 0.050 0.036 0.058 As + Sb............. 0.0038 0.0038 0.0038 0.0038 0.0031 0.0031 The bars were heated in an electric muffle to about 1,650" F. and rolled into rods. The rods were annealed, pickled, and drawn to No. 12 B. & S. gauge wire. The wire which was to be used for the annealing test was cut into 38-in. lengths and each length made into a coil 6 in. in diameter. The separate coils were marked so that they might readily be identified

Jan 1, 1915

By J. S. Bowles

THE martensite transformation in lithium, dis- covered by Barrett,' has been studied extensively by X-ray techniques by Barrett and Trautz,² and Barrett and Clifton.V he present paper reports the results of an investigation into the metallographic characteristics of lithium martensite. Such an investigation has not been carried out before. The spontaneous transformation in lithium consists of a change from a body-centered cubic to a close-packed hexagonal structure with the hexagonal layers in imperfect stacking sequence." As far as is known at present, this transformation can be regarded as being crystallographically equivalent to the body-centered cubic to close-packed hexagonal transformation that occurs in zirconium,5 although stacking errors have not been reported in zirconium. From a study of the orientation relationships in zirconium, Burgers5 as proposed that the martensite transformation, b.c.c. to c.p.h., occurs by a heterogeneous shear on the system (112) [111]. The crystal-lographic principle underlying this proposal is that the configuration of atoms in the (112) plane of a b.c.c. structure is exactly the same as that in the (1010) plane of a close-packed hexagonal structure based on the same atomic radius. The pattern in 2v2 both these planes is a rectangle d X 2v2d where v3 d is the atomic diameter. Thus a close-packed hexagonal structure can be built up from a body-centered cubic structure by displacing the (112) planes relative to each other.* This mechanism leads to orientations that can be described by the relations: (110)b.c.e. // (0001)c,p.h.; [111]b.c.c. // [1120]c.p.h Observations confirm these relations. In zirconium, Burgers' measurements indicated an angle of 0" to 2" between the close-packed directions, while Barrett's measurements on lithium indicated an angle of 3". According to the Burgers' mechanism, the martensite habit plane for this transformation would be expected to be the (112)b.c.c. plane, for this plane would not be distorted by the transformation. One of the purposes of this investigation was to find out whether the observed lithium habit plane agrees with this prediction of the Burgers' mechanism. Experimental Procedure Materials: The lithium was from the same purified ingot used by Barrett and Trautz.² The Bridgman technique was used to produce single crystals. To maintain a temperature gradient in the melt, during the production of these crystals, it was necessary to use a steel mould with a wall thickness of only 0.015 in. Metallographic Techniques: Lithium specimens could be given an excellent metallographic polish by swabbing them gently with cold methyl or ethyl alcohol.? The best results were obtained with methyl alcohol saturated with the reaction product, lithium alcoholate. With higher alcohols the reaction became progressively slower and the attack became an etch pit attack rather than a polish attack. Butyl and amyl alcohols were used for macroetching. After polishing, it was necessary to remove all traces of alcohol from the specimens; otherwise, on subsequent quenching in liquid nitrogen, the alcohol froze to a glassy film. The alcohol was removed with dry benzene. The benzene in turn had to be removed before quenching, but since it does not react with lithium it could be allowed to evaporate. The specimens could then be quickly quenched before they began to tarnish. This operation could be carried out in air on all but excessively humid days when it was advisable to use an atmosphere of dry nitrogen or argon. For examinations at room temperature, the specimens could be transferred directly from the benzene bath into a bath of mineral oil. In mineral oil the specimens oxidized slowly by the diffusion of oxygen through the oil but the structure remained visible for about an hour. Lithium Martensite: Specimens prepared in the manner described above transformed spontaneously to martensite with an audible click when quenched into liquid nitrogen; i.e., M, was above the boiling point of nitrogen (77°K). The disparity between this result and the M, temperature of 71°K, found by Barrett and Trautz, is probably to be attributed to the large grain size and freedom from mechanical deformation of the specimens used in the present work. The relief effects produced by the transformation did not disappear when specimens were quenched from liquid nitrogen into mineral oil at room temperature. This permitted the microstructures to be studied at room temperature where, of course, the martensitic phase was no longer present. Typical micrographs of lithium "martensite" made at room temperature are reproduced in figs. 1, 2, and 3. As anticipated by Barrett and Trautz, the microstruc-

Jan 1, 1952

By H. A. Kuhn

THE Pittsburg coal field in western Pennsylvania, is conceded to be the most important in the world. To measure its importance it is necessary to understand the extent of its service in the various industries of the country. Probably 90 per cent. of the pig iron manufactured in the United States up to the present time has been made by using coke manufactured from the Pittsburg coal seam in western Pennsylvania. This coal field is the foundation on which the city of Pittsburg rests and is the reason for the great growth of the iron industry in the Pittsburg district. Iron ore is brought to this district, not because Pittsburgh is a. natural location, over other locations, for the iron and steel industry-as its position places the manufacturer at the mercy of the railroads-but the ore is brought 1,100 miles to meet the fuel. It can be said that the illuminating-gas industry in the United States has used this coal exclusively to the same extent that the pig-iron maker has used it. It may be also said that 20 to 25 per cent. of the fuel used on railroads in the United States conies from this coal field. The Pittsburg coal field is unquestionably the center of the industrial population of the United States, for in addition to the industries of the district and those closely adjoining, it has tributary to it all the cities and industries along the Great Lakes and practically all of Canada with the exception of the extreme western and eastern ends. It supplies the industries and population west of Duluth and Superior many hundreds of miles. This coal is floated down the Ohio and Mississippi rivers, supplying the towns en route, and is delivered in New Orleans, a distance of 2,200 miles, for approximately SO to 90 c. per ton transportation cost. It is delivered on the docks of Superior and Duluth at a cost of transportation 50 c. a ton less than the cost of transporting the same coal from Pittsburg to a local consumer in Philadelphia. With other Appalachian coals it has large markets east and along the seaboard, especially for byproduct-coke making and the illuminating-gas industry. It is considered the premier railroad fuel of the world on account of the fact that this coal in a given-sized locomotive will probably haul more cars than any other coal in the

Jan 10, 1914

By R. Haynes

ON the basis of compositional changes of a phase observed in a eutectoid Cu-Al alloy1 it has been suggested that mechanisms for the decomposition of the ß phase proposed by earlier workers2-5 were incorrect. These data are reinterpreted in conjunction with lattice parameter data obtained on an alloy containing 12.2 pet Al, whose isothermal transformations have been reported elsewhere.5 The a Lattice Parameters of a 12.2 Pet A1-Cu Alloy—~iffraction patterns of completely transformed specimens were obtained in a back reflection camera using copper Ka radiation. Lattice parameters of

Jan 1, 1959

By Ali M. Heidarieh Zadeh, Raghu N. Singh

The paper presents a stability investigation of shaft intersections and pit bottom roadways in the vicinity of upcast and downcast shafts at a colliery in the U.K. Aschemeof instrumentation was aimed at monitoring the strata displacement surrounding the pit bottom roadways and shaft intersections with a view to ascertaining the origin of the strata movement and effectiveness of the control measures. The bore- hole instrumentation results together with a theoretical analysis suggested that the cause of instability could be attributed to the drivage of a roadway within the shaft pillar. A semi-empirical technique was used to calculate the amount of support resistance required to reinforce the pillar to take additional abutment load. A rock bolting system was designed to provide a required increase in thrust capacity of the roadway support. The results indicated that roadway closure was effectively controlled after installation of bolts indicating efficacy of the control measures adopted.

Jan 1, 1982

Teamwork: The famous first sentence of an essay en- titled Aphorisms, by Hippocrates, is as follows: "Life is short, the Art long, opportunity fleeting, experience treacherous, judgment difficult." The future of science does not depend so much on the number of scientists or the number of colleges, but rather on the individual qualities and the degree of perfection of a limited group of leading scientists and colleges. These are individual factors which require inherent talent which in turn is a condition evolved after generations of culture. Thus, very elaborate higher education for indiscriminate masses of humanity or students may not necessarily show the expected results. In other words, it is possible that higher specialized education should be given only to the few talented individuals, and their capacity and worth should be judged by as highly qualified and talented teachers. Quality is the greatest of all competitive aids. An essential qualification that must be possessed by a quality mineral industries college is a high caliber teaching staff, for the mineral sciences will advance in the coming years only if the leading minds of today are made avail- able as the mental springboards for our scientists of tomorrow. Mineral industries schools are finding it increasingly difficult to maintain a high caliber staff of instructors and administrators in competition with private business and governmental demands for similar

Jan 1, 1950

By C. E. Sims, G. A. Lillieqvist

The following presentation is more a summation of observations made and conclusions drawn over a period of three to four years than a report of experiments made with a definite objective. Tests were made, of course, to verify hypotheses, but the large mass of data was collected incidental to other work. Lack of space forbids the presentation of more than a few of those data. On the other hand, it is unfortunate that some of the most illustrative examples are not available. The work is admittedly incomplete but is presented in the hope that it will stimulate further work along a similar line. The answers to many of the questions left unanswered by this paper will be found only after long and painstaking study, such as is scarcely possible in a commercial laboratory where problems of immediate importance consume most of the time. It is also hoped that this study will in some measure throw light on some of the dark spots of steelmaking, and help to clarify some of the annoyingly vague references to "good practice." Only cast steel was studied and the conclusions apply to cast steel, but it is the authors' opinion that the quality of rolled or forged steel is largely dependent on the quality of the ingot, which is a casting. Although this discussion deals almost entirely with inclusions, it is important that the reader understand that only those natural inclusions which owe their origin to the solubility of certain materials in steel and to the chemical reactions of steelmaking are considered. Accidental inclusions, such as entrapped particles of slag, nozzle, runner, or mold arc outside its province and are not considered. Such accidental inclusions are always dangerous and should be carefully avoided. Relation between Ductility and Nonmetallic Inclusions In September, 1928, an acid electric furnace was put into operation at the Indiana Harbor plant of the American Steel Foundries. Following the usual practice, aluminum additions were made in order to obtain sound castings. Immediately the problem of low ductility arose. Previous to that time, only open-hearth steel was produced, and, aluminum being used rarely in that steel, there had been practically no trouble with low ductility in the lower carbon range.

Jan 1, 1932

By W. T. Hicks

Visual observation of the oxidation of columbium shows that the protective behavior noted previously in gravimetric work in the early stages of the reaction below 600°C and throughout the reaction at 640°C is associated with an adherent oxide. The fact that the oxide is seen to move outward from the metal at temperatures from 550° to 935°C implies that the reaction takes place at the oxide-metal interface throughout this temperature range. THE work described in this paper further clarifies the complex oxidation kinetics of Cb revealed, for example, by the continuous gravimetric studies of T. L. Kolski.1 Time-lapse motion picture studies reveal details of the reaction not provided by a study of the combustion products. EXPERIMENTAL PROCEDURE Cb specimens were prepared from material with the following typical analysis: 0, 0.03 pct; N, 0.002 pct; C, 0.006 pct; Ta, 0.04 pct; Fe, 0.01 pct; Ni <0.003 pct; and Cr <0.003 pct. Arc-cast ingots were swaged and cold rolled into slabs. These slabs were machined into blocks 7/16 by 7/16 by 7/16 in; 1/16-in. holes were drilled through the large face of the blocks for suspension. The samples were then de-greased and annealed 1 hr at 1200°C in vacuum. The sample was suspended by a platinum and Pt 10 pct Rh thermocouple inside a 1-in. quartz tube in a Kanthal wound furnace (2 in. OD by 4 in. long) equipped with windows 1/2 in. sq. A Cine-Kodak Special II 16 mm motion picture camera was trained on the sample through a Spencer microscope adjusted so that a magnification of X1.5 resulted on the film. Super Anscochrome film was used to record the events in color. Argon was flushed through the furnace while the sample came to temperature. The argon was then replaced by a stream of dry oxygen at 1 atm. Pictures were taken at the rate of eight per second for about 20 sec during the change of atmosphere. Then by use of a Stevens time-lapse device pictures were taken at the rate of four per minute starting within 1 min of the initial oxygen flow. In this manner continuous visual records of the oxidation of pure Cb

Jan 1, 1962