Search Documents

By A. Kenneth Schellinger

THE terms surface tension .and surface energy are well known when applied to liquids and are generally described by referring to the excess energy of the air: liquid interface as a result of unsaturated molecular forces surrounding the surface molecules of the liquid due to the presence of the air phase on one side. Such unbalanced forces produce the familiar water droplet of spherical form and are generally summed up as a surface tension measured in dynes per centimeter which can be shown mathematically to be equal numerically to a corresponding surface energy expressed in ergs per square centimeter. A specific surface energy, however, is best thought of as the energy necessary to produce one unit of new surface on a substance. Hence, in producing a bubble in a flotation cell the impeller must supply surface energy corresponding to the air: liquid interfacial area on the interior of the bubble. Inasmuch as it is relatively easy to extend or contract the surface of a liquid, there are a number of successful methods for liquid surface tension, or energy, measurement based upon surface deformation. This happy state of affairs does not, however, extend to solids, which are considered to possess surface energies for the same reasons as do liquids, i.e. because of unsaturated ionic bonds at the solid gas interface. As in the case of the flotation cell producing surface on liquids as new bubbles, it takes energy to produce new surface on solids as new particles. As every mill man knows, this surface is produced on mineral solids in a grinding mill by the action of a tumbling mass of iron balls. But here so much energy usually is wasted by the inefficient action of these balls that a large amount of heat is generated, and the surface energy production may be easily confused with the energy necessary to produce this ineffective heat. The tumbling balls and fracturing minerals ultimately take their energy from a rather large electric motor. It has been variously estimated that from 10 to 20 pct" only of this energy from the motor does not appear as heat and may be presumed to appear as surface energy on the minerals present.. Such a production of new surface on the mineral phases is accompanied, of course, by a size reduction that is inevitable as more and more mineral interior molecules become surface molecules by the fracture exposure. This size reduction of mineral particles, although the most obvious feature and perhaps the sole object of the milling operation, is from this energy viewpoint the outward manifestation of the production of surface energy only. Measurement of the characteristic surface energies of pure minerals and their various mixtures in ores would be a step towards understanding of the energetics of the commercial grinding operation. In addition, the characteristic surface energy of a mineral is probably a physical property specific for that mineral, and therefore, from a scientific standpoint, should be measured. It is interesting to note that, in contrast to the large body of work on the surface tensions of liquid systems and biological systems, the field of solid surface energies has been neglected. Prior to. 1920 it is difficult to find more than one or two references to work on solid surface energies in Chemical Abstracts. Since 1920 such references number somewhat less than 100, while those on liquid systems are numbered in the thousands. Much of this apparent neglect of the field of solid surface energies (the term is intended to be somewhat inclusive at this point and refers both to the solid: gas, and the solid: liquid interface) is because of the lack of a reliable method of measurement rather than any lack of scientific curiosity. It was, and still is, difficult to produce new surface on a solid without the simultaneous production of interior changes in the same solid which may consume part of the energy used. The extension in the surface area can be measured, but the interior crystal-

Jan 1, 1952

By E. C. Skinner

Cardox, which consists essentially of a steel tube containing carbon dioxide compressed to the liquid state, is a trade name designating a device used principally in coal mines to break down coal. The use of Cardox to break down coal was developed in the Middle Western coal fields around 1927 or 1928. At first, a large, heavy tube was used, requiring many parts. Through experimentation and technologic improvement, the weight of the tube has been brought down from 88 lb. to 20 lb. and the new, light tube makes use of larger volumes of CO2 at lower pressures than formerly was thought possible. This blasting method is extensively used today in coal mines and probably one tenth of the bituminous coal produced in the United States is prepared with Cardox. Construction and Application As used in the coal mine, Cardox looks like a piece of steel pipe 2 to 3 in. in diameter and 3 to 5 ft. long. When it is necessary to fire a shot, the tube is wired with two leg wires that are long enough so that when the tube is pushed the desired distance into the hole the wires will protrude 5 to 6 in. It has been found that No. 18 insulated copper annunciator wire is the best material for leg wires. A two-conductor rubber-covered shot-firing cable of sufficient length is then attached to the leg wires. A 2 to 6-volt current is applied, either by means of shot-firing batteries or the standard type of shot-firing generator. Upon the application of the current, the charge in the cartridge is set off. Because the breaking action upon the coal is supplied by the relatively slow physical expansion of the carbon dioxide gas rather than by the rapid chemical formation of gases as in more familiar explosives, the result is a slow heaving action, somewhat similar to that produced by black powder, rather than a shap detonating effect. Permissible powder does its work at roughly ten times the pressures in use with Cardox. The escaped gas from a Cardox shot apparently works along the planes of weakness in the coal face, such as the coal cleats, the edges of the cut, and along the top of the seam, breaking off the coal toward the free faces and heaving the mass of coal outward. Cardox tubes are manufactured in various sizes to take care of variable conditions of seam size, undercut depth, cleatage, coal hardness, and so forth. The tubes range in diameter from 2 to 3 in. (Table I) and the normal CO2 charge is from 24 to 96 oz. For any one tube size, several sizes of shear disks are available, thus excellent control of the type of shooting desired is possible. In general, local experience and experimentation dictate the size of tube chosen for any particular job. For high coal, and deeper or wider cuts, a larger size is chosen to start with, and the opposite is true for low coal, softer coal, or small cuts. After the tube size has been experimentally selected, tests are run in the mine to determine how many shot holes are needed and where the holes should be placed. The size of the disk,

Jan 1, 1944

By E. C. Skinner

Cardox, which consists essentially of a steel tube containing carbon dioxide compressed to the liquid state, is a trade name designating a device used principally in coal mines to break down coal. The use of Cardox to break down coal was developed in the Middle Western coal fields around 1927 or 1928. At first, a large, heavy tube was used, requiring many parts. Through experimentation and technologic improvement, the weight of the tube has been brought down from 88 lb. to 20 lb. and the new, light tube makes use of larger volumes of CO2 at lower pressures than formerly was thought possible. This blasting method is extensively used today in coal mines and probably one tenth of the bituminous coal produced in the United States is prepared with Cardox. Construction and Application As used in the coal mine, Cardox looks like a piece of steel pipe 2 to 3 in. in diameter and 3 to 5 ft. long. When it is necessary to fire a shot, the tube is wired with two leg wires that are long enough so that when the tube is pushed the desired distance into the hole the wires will protrude 5 to 6 in. It has been found that No. 18 insulated copper annunciator wire is the best material for leg wires. A two-conductor rubber-covered shot-firing cable of sufficient length is then attached to the leg wires. A 2 to 6-volt current is applied, either by means of shot-firing batteries or the standard type of shot-firing generator. Upon the application of the current, the charge in the cartridge is set off. Because the breaking action upon the coal is supplied by the relatively slow physical expansion of the carbon dioxide gas rather than by the rapid chemical formation of gases as in more familiar explosives, the result is a slow heaving action, somewhat similar to that produced by black powder, rather than a shap detonating effect. Permissible powder does its work at roughly ten times the pressures in use with Cardox. The escaped gas from a Cardox shot apparently works along the planes of weakness in the coal face, such as the coal cleats, the edges of the cut, and along the top of the seam, breaking off the coal toward the free faces and heaving the mass of coal outward. Cardox tubes are manufactured in various sizes to take care of variable conditions of seam size, undercut depth, cleatage, coal hardness, and so forth. The tubes range in diameter from 2 to 3 in. (Table I) and the normal CO2 charge is from 24 to 96 oz. For any one tube size, several sizes of shear disks are available, thus excellent control of the type of shooting desired is possible. In general, local experience and experimentation dictate the size of tube chosen for any particular job. For high coal, and deeper or wider cuts, a larger size is chosen to start with, and the opposite is true for low coal, softer coal, or small cuts. After the tube size has been experimentally selected, tests are run in the mine to determine how many shot holes are needed and where the holes should be placed. The size of the disk,

Jan 1, 1944

By Robert C. Stephenson

In 1954, a year when general industrial production declined, it is significant that industrial mineral products continued in high demand. Phenomenal growth of the cement industry, increase in filler-fibre markets such as for asbestos and diatomite, expansion of the gypsum industry, and the increasing production of agricultural raw materials all illustrate the vitality of industrial minerals fields. Pioneer development of new industrial raw materials-wollastonite as a current example-requires keen foresight, hard work, and tremendous intestinal fortitude. The present-day requirements of industry for rigid quality control and uniformity of raw materials have resulted in highly specialized

Jan 3, 1955

By S. Kado, G. Derge, L. Yang

Self-diffusion coefficients of silver in molten silver have been measured by means of the capillary-reservoir method in the temperature range 1002" to 1105°C. The results can be .represented by the equation D = (7.10 i 0.06) X 10-4 exp [(—8150 ± 1130)/RT]. The heat of activation agrees within the limit of experimental uncertainty with that for the viscous flow. The validity of the Eyring and the Stokes-Einstein equations are examined on the basis of the self-diffusion coefficients obtained and the known viscosity data of molten silver. MEASUREMENT of the self-diffusion coefficient of silver in molten silver was made in the temperature range 1275° to 1378°K, using the capillary-reservoir method and &"' as the radioactive tracer. The experimental arrangement is shown in Fig. 1. Silver of 99.99 pct purity (fine silver), was melted and degassed in vacuum in a graphite crucible situated inside a McDanel vacuum jacket. The crucible (4 in. tall and 1 in. ID) was protected both at the top and at the bottom with graphite shields and contained about 220 g of silver. The sample holder was a piece of graphite rod (1 in. long and 1/2 in. diam) with 4 capillaries drilled longitudinally into it. The holder was screwed onto a long graphite rod (12 in. long and 74 in. diam) which was connected to a steel disk hanging on a nylon string through a glass pulley. The steel disk kept the sample holder at the center of the McDanel tube and was heavy enough to overcome the buoyancy when the holder was lowered into the molten silver. By turning a handle connected to the pulley through a tapered glass joint, it was possible to raise or lower the sample holder without breaking the vacuum. Two such arrangements were constructed, sitting side by side in 2 Kanthal furnaces. One with non-radioactive silver in its crucible was used for the diffusion run and the other with radioactive silver in its crucible was used for filling the capillaries. To fill the capillaries with radioactive silver, the sample holder was degassed first and then lowered into the radioactive molten silver in vacuum. Purified argon gas was then admitted into the system to push the liquid silver into the capillaries. After cooling in argon, the filled capillaries were polished on emery paper to expose the top of the rod and used immediately as samples for the diffusion run which was carried out at the same temperature as that used for filling the capillaries. During the diffusion run, the samples were degassed in vacuum and lowered slowly into the nonradioactive molten silver before purified argon was admitted into the system. After a predetermined period of time, the samples were raised out of the melt and cooled in argon. The temperature of the melt was measured before and after the run with a chromel-alumel thermocouple inside a McDanel protection tube. Another chromel-alumel thermocouple attached to the outside wall of the McDanel vacuum jacket was used to indicate any fluctuation in the temperature of the furnace during the run, which was found to be less than ± 2°C for the longest run made (93 min). The temperature gradient inside the molten silver was found to be negligible. No significant difference was observed in the results obtained whether the melt was stagnant during the run or was stirred by raising and lowering the sample holder slowly a few times a minute for a distance of about 1/4 in. inside the melt.

Jan 1, 1959

By V. W. Bihlman, H. M. Williams

In the construction of internal-combustion engines, the cooling of the combustion chamber and pistons is of great importance. In certain types of engines, the adequate dissipation of heat from the bearings is also important. One of the important factors affecting heat dissipation from these parts is the thermal conductivity of the material used. A search of the technical literature shows that, in general, the thermal conductivity of the elements1 has been determined accurately by a number of investigators. The data on the industrial alloys are, however, meager. For an investigation of these alloys, the thermal-conductivity apparatus described in this paper has been constructed at the laboratory of the General Motors Research Corporation. It is desirable that an apparatus for work of this nature should give fair accuracy of results with a convenient form of specimen and a reasonable rapidity of operation. A summary of the different methods of determining thermal conductivity is given in the first volume of the " Dictionary of Applied Physics," pages 429 and 470. The method selected as best satisfying these conditions is that of Griffith, on page 443, with the addition of a guard ring similar in principle to the method used by Berget (P. 445). Briefly, the method consists of heating one end of a bar T, Fig. 1, electrically, measuring the amount of heat transmitted through the bar by a flow calorimeter J fastened to the other end, and measuring the temperature gradient along the bar. To compensate for the loss of heat laterally, the test bar is surrounded by a guard ring E, in the form of a steel pipe, which is electrically heated at the bottom and cooled at the top with a

Jan 1, 1923

By V. W. Bihlman, H. M. Williams

In the construction of internal-combustion engines, the cooling of the combustion chamber and pistons is of great importance. In certain types of engines, the adequate dissipation of heat from the bearings is also important. One of the important factors affecting heat dissipation from these parts is the thermal conductivity of the material used. A search of the technical literature shows that, in general, the thermal conductivity of the elements1 has been determined accurately by a number of investigators. The data on the industrial alloys are, however, meager. For an investigation of these alloys, the thermal-conductivity apparatus described in this paper has been constructed at the laboratory of the General Motors Research Corporation. It is desirable that an apparatus for work of this nature should give fair accuracy of results with a convenient form of specimen and a reasonable rapidity of operation. A summary of the different methods of determining thermal conductivity is given in the first volume of the " Dictionary of Applied Physics," pages 429 and 470. The method selected as best satisfying these conditions is that of Griffith, on page 443, with the addition of a guard ring similar in principle to the method used by Berget (P. 445). Briefly, the method consists of heating one end of a bar T, Fig. 1, electrically, measuring the amount of heat transmitted through the bar by a flow calorimeter J fastened to the other end, and measuring the temperature gradient along the bar. To compensate for the loss of heat laterally, the test bar is surrounded by a guard ring E, in the form of a steel pipe, which is electrically heated at the bottom and cooled at the top with a

Jan 1, 1923

By Howard Eavenson

The data given in the paper were collected to furnish an idea of the amount required in various operations of bituminous mining to produce a ton of coal, the plants selected being well-managed ones. With these are included some figures compiled from U. S. Coal Commission's report showing the average amount of labor in various classes of mines. THE information contained in the following paper was collected at the request of the U. S. Coal Commission, and is, published with the permission of that body and of the various companies furnishing the data. For obvious reasons, the names of the companies are not given. No data were gotten from States south of Virginia or west of the Mississippi River. The data about the amount of labor, in man-hours, required in producing a ton of bituminous coal have been collected with the idea of showing what is being done at some well-managed plants, and not to show the average amount required by all mines, which undoubtedly is considerably higher than the average of the figures shown.* Almost all of the figures were supplied by the various companies in reply to a questionnaire; when they were obtained from other sources the company was asked to verify them. On account of the amount of work required, the data were only requested for one or two months for each plant, and the figures represent in each case a month when the car supply was good and the work was practically steady. In the case of most of the West Virginia and Kentucky mines, these conditions were best met in May and June, 1922. The mines for which the figures are given are arranged by states and as to whether the mine operates under union or non-union or open-shop conditions. The union mines listed are generally considered to be as well-managed as are the non-union ones. The production per month in a few cases includes the amount of slate which is loaded and hauled out of the mine, as of course this requires nearly as much labor per ton as does the coal. These cases are noted:

Jan 1, 1924

By J. L. Jorstad

The hypereutectic Al-Si alloys 390 and A390 have wear characteristics superior to any of the more common aluminum casting alloys. This excellent wear resistance, coupled with good mechanical properties, high hardness, and low coefficient of thermal expansion, has made these alloys candidates for the all-aluminum internal combustion engine, the application for which they were primarily developed. A390 alloy is intended for sand and permanent mold casting, and requires a lower iron ccxltent (0.5 pct maximum) than its die casting companion 390 alloy (0.6 to 1.1 pct Fe). The 17 pct nominal silicon in these alloys provides sufficient quantities of the hard primary silicon phase to assure a high degree of wear resistance, yet little enough of this phase, to minimize the casting and m achining problems associated in the past with the hypereutectic alloys. The mechanical and physical properties of 390 and A390 alloys are competitive with the best of the common aluminum casting alloys with the exception of low ductility. This low ductility is not considered a detriment, since in many applications these alloys replace cast iron. Corrosion resistance is similar to the standard alloys 380 and 333. Numerous parts, of varying degrees of complexity, have been cast of alloys 390 and A390, including engine blocks and heads. The deviations from normal good handling and casting practices that are required for the alloys are those associated with the presence of the primary silicon. To obtain optimum strength and machinability, the molten alloys should be treated with phosphorus to refine the primary silicon phase. Care must be exercised to properly control the pouring temperature and rate in order to minimize primary silicon growth and segregation. AUTOMOTIVE engineers have for years recognized the advantages of lighter weight and better heat transfer that aluminum could offer as material of construction for engine blocks. These advantages alone, however, are insufficient justification for acceptance of aluminum engines by the automotive industry. To be acceptable, an aluminum engine first must pass all tests to which cast-iron engines are subjected, and, in addition, must represent no cost penalty in manufacturing. None of the conventional aluminum casting alloys have sufficient wear resistance to withstand the tests to which cast iron is subjected as a cylinder bore material, and recent attempts to manufacture aluminum engines with cast-in-place iron sleeves could not compete costwise with the equivalent cast-iron engine. The prerequisite to an acceptable aluminum engine seemed to be a casting alloy with a high degree of wear resistance that would eliminate the necessity of cast-in iron sleeves or liners. The hypereutectic A1-Si alloys 390 and A390 have met this challenge.' Combined with modified pistons and a patented cylinder bore surface finish,2 the performance of these alloys in more than 1300 cold start and cold scuff tests, over 3500 hr of dynamometer wear and endurance tests, and more than 350,000 miles of road tests leaves no doubt as to the feasibility of running on bare aluminum cylinder bores. ALLOY DEVELOPMENT The desirable characteristics of the hypereutectic A1-Si alloys have been recognized for some time. Their excellent wear resistance and low coefficient of thermal expansions have been used to advantage in the production of diesel-type pistons in Europe and to a limited extent in this country. The major contributor to the good wear resistance of these alloys is the extremely hard primary silicon phase in the microstructure. Although the percent silicon used experimentally has been much higher, most commercial alloys have ranged from about 14 to 25 pct. Generally, as the silicon content is increased, wear resistance increases, and the coefficient of thermal expansion decreases. With increases in silicon, however, machinability and cast-ability tend to suffer. The development of a satisfactory aluminum engine block material at Reynolds involved the testing and evaluation of many alloys, covering a wide range of silicon contents and numerous variations of iron, copper, magnesium, manganese, and other alloying additions. Castability, mechanical and physical prop-

Jan 1, 1969

By C. E. Lesher

COAL has been fighting a rear-guard action since the last World War. The battle against competitive fuels has been largely guerilla warfare with more sniping within the ranks than of organized opposition. Oil and natural gas are the fuels that over these twenty odd years have driven coal backward and out of many profitable markets. Now, somewhat timidly, the coal industry is trying a new weapon; namely, Research, or let us more properly say, Organized Research. Engineers have been designing this weapon for many years, supported by those interested in coal, including some coal producers. A part of this pioneer work has been Fundamental Research, the Ph.D. kind that is over the heads .of most of us. Another part has been aimed at immediate objectives and realizable profits, the practical, man-in-the-street sort. That is Industrial Research. Enough has been accomplished to make a fair exhibit, but whether this new weapon will have sufficient fire power to rout the opposition, whether the industry will really go into production and use it, the next few years will tell. NEED FOR COAL RESEARCH To utter "Research" is to use the modern magic word; to conjure up the miraculous-rubber from weeds; radar; magnesium from sea water; yes, even gasoline from coal. Research is a very general term. It means something different to every man. What is the coal industry seeking with its research; or what should it seek? And, specifically, how is it going about the job; and is it taking the best way? There are many who say that Coal has been asleep at the switch, while Oil and Gas have been taking the energy business. In an organized way this is true. Large-scale, privately financed research is just started in the Pennsylvania, anthracite industry, and it is still a dream for bituminous coal. What has been done so far collectively is purely defensive; as, for instance, to improve mechanical devices for burning coal so as to be able to recover markets for house-heating fuel long since abandoned to oil and gas. To appreciate just how seriously bituminous coal has slipped back in the national economy in the past 25 years, one has only to recall that, in the last war the Navy required for its operations all the high-grade, low-volatile coal that could be produced, and that anthracite was withdrawn from the middle and northwest markets to keep the eastern seaboard warm. All coal was "rationed" by zones, if not to individuals. Now the Navy, the Armed forces and the Merchant Marine are propelled by oil and gasoline. Gasoline and heating oil are rationed to individuals. Production of all coal in this country in 1918 reached the historic figure of 678,200, 000 tons, and in 1943, after 25 years, it is expected to reach a special wartime total of 660,000,000 tons. Meanwhile, production of crude oil this year may exceed 1,500,000,000 bbl., and like that of natural gas, reach four times the amount produced in 1918.

Jan 1, 1944

G. K. BURGESS,* Washington, D. C.-In the service tests, the Advisory Committee on Aeronautics considered it highly necessary, particularly for seaplanes, to find out whether or not it was necessary to paint exposed parts; reports have been obtained but have not been pub-lished at the present time. Investigations were carried on at three Navy Yards. On just a hurried examination, the inspection was made about two weeks ago and the results are now being digested an examination shows that the aluminum alloys, whether painted or unpainted, stand up very well. It apparently is not necessary to paint, which, of course, is a very important item in the question of the weight of seaplanes. We will be able to report on that, I expect, probably at the next meeting.

Jan 12, 1919

OPEN-HEARTH refractories are not merely an accessory to the furnace. They are the furnace, to all intents and purposes. The steel work of the main structure is merely an open frame which helps to support the refractories; and the regenerators, a necessary part of the furnace system, consist almost entirely of refractories. Not only do refractories constitute the essential part of the furnace, but they also carry the liquid steel all the way 'to the point where it begins to solidify. On leaving the furnace the liquid passes through a refractory runner into a refractory-lined ladle, then through a refractory nozzle closed by a refractory stopper on the end of a rod protected by refractory sleeve bricks. The liquid is sometimes sent through an additional refractory- lined tundish, a supplementary ladle, or a refractory runner for bottom pouring, until it finally enters the iron mold in which it solidifies. Even in the mold, refractory materials are sometimes used to provide a nonconducting "hot top." This series, from runner and ladle to hot top, inclusive, is often referred to collectively as the "pouring-pit refractories." REFRACTORY RAW MATERIALS The raw materials available are best classified into basic and acid types. The principal basic raw materials are magnesite, dolomite, and chrome ore. The principal acid materials are silica in various natural forms, and fireclay. Magnesite. Austria was the principal source of magnesite (MgC03) until recent years, when the Province of Quebec, in Canada, and the states of Nevada and Washington became important sources for the American steel industry. More recently these natural sources have been supplemented by the so-called "sea-water magnesite"-which is the name somewhat incorrectly given to magnesium hydroxide obtained as one of the products

Jan 1, 1951

By H. L. Talbot, A. J. Hall, R. S. Young

A METHOD for the chemical differentiation of oxidized cobalt from sulphide cobalt in complex mine and concentrator products is of considerable interest to a number of mining companies throughout the world. At Rhokana Corporation, in Northern Rhodesia, for instance, cobalt is found chiefly in the sulphide form, as carrollite, but a cobalt oxide mineral also occurs irregularly underground, and relatively small quantities in the mill feed from time to time are difficult to detect it visually at the concentrator. The oxide cobalt is not amenable to the sulphide flotation process used at Rhokana and nearly all of it passes into the tailing. The occasional. period when high tailing losses occur with no appreciable change in the cobalt content of the mill feed has naturally been disturbing to the concentrator staff, who had no means of determining whether an influx of cobalt oxide ore or laxity on the part of the mill flotation operators were responsible for these results. A procedure for determining oxidized copper minerals, based on their solubility in dilute sulphuric acid saturated with SO2, has been used for many years in the copper industry. In the presence of cuprite the procedure fails, but otherwise it gives results quite satisfactory for control purposes. Empirical methods for determining oxidized forms of zinc and lead have been proposed, but they are generally unsatisfactory except in isolated cases of a very simple ore. No published procedure for determining oxidized forms of cobalt or similar elements has come to the authors' notice. EXPERIMENTAL PROCEDURE There are obviously two alternatives in attacking a problem of this nature. One is to employ a solvent for oxide cobalt that will not dissolve cobalt sulphide. The other is, to find a substance capable of oxidizing the cobalt sulphide to sulphate, which of course is water-soluble and can then be leached from the water-insoluble oxide cobalt. A representative sample of Rhokana cobalt oxide ore was secured, ground to minus 200-mesh, and carefully rolled to furnish a standard sample for this work. The analysis of this material gave the following percentages: Co, 0.55; Cu, 1.64; Fe, 2.98; S, 0.08; SiO2, 41.42; A1203, 11.20; CaO, 13.82; MgO, 3.80. As a source of cobalt sulphide a similar large sample of carrollite was prepared, analyzing Co, 23.36 per cent; Cu, 27.32; and S, 31.13. This sample of course was not pure carrollite, but was the best obtainable in quantities sufficient for a standard intended for considerable work. It was a pure sulphide sample, microscopic examination showing only carrollite, a little bornite, and gangue, with no visible sign of oxidized ore present. A wide variety of reagents were used in an effort to selectively dissolve oxide cobalt or to oxidize sulphide cobalt to

Jan 1, 1946

By Elmer W. Pehrson

The term "survival" in the title means the preservation of a society in which men are free from the political and economic restraints that characterize totalitarian systems, be they communist, socialist or facist. It means the ability to withstand the enemy's offensives in the fields of propaganda, commercial competition and, if necessary, war. The temptation to substitute "victory" for "survival" is great but a realistic appraisal of the creeping socialism and demagoguery that pervade our time indicates that we may have to be content with survival in status quo. "Mineral strength" means assurance that adequate supplies will be available to meet all the contingencies of cold and hot wars. The overall mineral position of the U. S. viewed in the light of these premises is far from secure. It is true that we are the leading producing and consuming nation of the world, but the Soviet Union is gaining and the Sino-Soviet Bloc confronts us with a sobering potential. The emergence of the Common Market in Europe as an economic and political unit places a third independent entity into the competition. Our total mineral output continues on an up- ward trend but the reverse is true in certain strategic commodities. Moreover, consumption is moving ahead faster than production so that there is increasing dependence on imports which has significant adverse geopolitical connotations. There is widespread belief that our resources can at least maintain present levels of self-sufficiency during this critical period in world history, but social dreamers, the labor monopoly, and trade and taxation policies have discouraged aggressive activity in exploration and development, and access to essential foreign sources is threatened by a variety of circumstances. Our stockpiles, belatedly built up to achieve minimum protection against shortages in time of war, are under. political attack and threatened with partial destruction on the basis of what are at best uncertain assumptions regarding the new: look of global warfare.

Jan 11, 1962

By Sanai Nakabe

Japanese wartime economy demanded domestic cobalt production. This paper describes a process operated for two years at the Besshi mine and smelter on extremely low grade (0.1 pct Co) pyrite concentrates obtained from copper ore. 'The steps in the process were roasting, leaching, precipitation, reduction fusion to crude cobalt, and finally refining by electrolysis to 99+ pct. COBALT ore deposits in Japan are all small and of poor grade. In the past, a small amount of cobalt has been produced from the best portions of a few of these deposits, and very little production is expected in the future. In addition to these lean cobalt ores, cobalt is present in the cupriferous pyrite which is fairly abundant although of low grade, as is shown in Table I. Considerable cobalt is expected from these deposits because of their extent. Cobalt cannot be exclusively recovered economically from ore of this type; however, if means could be devised to recover it as a byproduct of copper production, a fairly large production at reasonable cost could be expected from Japanese sources. It was along this line that the research work was done. Selection of Suitable Process The process for extracting cobalt differs from ore to ore according to their composition. The difficulty in cobalt metallurgy arises from the fact that chemically cobalt resembles many such common metals as Mn, Fe, Ni, Cu, and Zn, associated with it in the ores. In the present case the most serious difficulties were: 1—Extremely low grade ore, 0.1 pct Co. 2—The large proportion of iron accompanying cobalt and its close similarity in chemical behavior. 3—The fairly large proportion of zinc and manganese and their chemical similarity to cobalt. The recovery of cobalt oxide as a byproduct of the hydrometallurgy of copper had been attempted in Japan but was stopped after a short period because it proved uneconomical. The literature disclosed no method for the recovery of cobalt from cobaltiferous copper pyrite and it was therefore necessary to devise a new process. The following basic principles were considered in selecting the process: 1—A major alteration in copper production methods should not be necessary. 2—The first step should be the extraction of cobalt leaving the large quantity of iron unaffected. For this purpose wet metallurgy would be preferred.

Jan 1, 1952

By S. B. Patterson, A.R. Amos

Log washers have been used for many years in the washing of clay iron ores, phosphate rock and manganese ores, but not until the past 15 years have they been employed to any extent in the preparation of aggregate materials and fluxing stone. For a machine of such importance where tenacious clay or soft rock must be eliminated, there are few data generally available. The purpose of this paper is to set forth the results obtained from several operations, together with a few suggestions for planning a specific installation. Where the material to be washed out consists of loose surface soil, silt, or small amounts of quickly soluble clay, there is little competition with other forms of washers, because greater power and maintenance are required for the operation of log washers, but where the foreign matter is a stiff clay, such as occurs with high-calcium limestones and in marginal gravel deposits, the ability of other kinds of washers to eliminate completely the hard clay balls is at least uncertain. Then the log washer comes into its own field, for with the breaking and churning action of the logs it will clean out the toughest clay. Even with material from the hydraulic dredge, if it contains tough clay, the log washer is desirable unless the gravel is subjected to a costly soaking and rehandling process. Recently there has been a considerable development in other types of machines to accomplish these results but it is not within the scope of this paper to make comparisons between competitive types, but to present the best obtainable data on log washers only. From the primitive design that gave it its name, a long log hewn from a tree, with paddles forged to shape from strap iron and attached by lag screws, the log washer has gradually been developed to the present all-steel type. As now manufactured, the log washer consists essentially of two built-up logs on which are mounted a series of paddles, carried by shafts fitted at the ends of the logs on bearings fastened outside the enclosing steel box, or trough, which is set at an angle of about 5" to 10" and into which the material is fed. Stuffing boxes at the places where the shafts pass through the box at the lower end are equipped with water-

Jan 1, 1938

By A. R. Amos, S. B. Patterson

Log washers have been used for many years in the washing of clay iron ores, phosphate rock and manganese ores, but not until the past 15 years have they been employed to any extent in the preparation of aggregate materials and fluxing stone. For a machine of such importance where tenacious clay or soft rock must be eliminated, there are few data generally available. The purpose of this paper is to set forth the results obtained from several operations, together with a few suggestions for planning a specific installation. Where the material to be washed out consists of loose surface soil, silt, or small amounts of quickly soluble clay, there is little competition with other forms of washers, because greater power and maintenance are required for the operation of log washers, but where the foreign matter is a stiff clay, such as occurs with high-calcium limestones and in marginal gravel deposits, the ability of other kinds of washers to eliminate completely the hard clay balls is at least uncertain. Then the log washer comes into its own field, for with the breaking and churning action of the logs it will clean out the toughest clay. Even with material from the hydraulic dredge, if it contains tough clay, the log washer is desirable unless the gravel is subjected to a costly soaking and rehandling process. Recently there has been a considerable development in other types of machines to accomplish these results but it is not within the scope of this paper to make comparisons between competitive types, but to present the best obtainable data on log washers only. From the primitive design that gave it its name, a long log hewn from a tree, with paddles forged to shape from strap iron and attached by lag screws, the log washer has gradually been developed to the present all-steel type. As now manufactured, the log washer consists essentially of two built-up logs on which are mounted a series of paddles, carried by shafts fitted at the ends of the logs on bearings fastened outside the enclosing steel box, or trough, which is set at an angle of about 5" to 10" and into which the material is fed. Stuffing boxes at the places where the shafts pass through the box at the lower end are equipped with water-

Jan 1, 1938

US 4,185,996 -- Removal of arsenic and sulfur Impurities from arsenic-containing cobalt sulfide ore. The ore is oxidized In air at a temperature of 700 to 800°C for 3 to 8 hr to drive off the bulk of the sulfur The oxidized ore 1s heated with a reducing gas at a temperature of 700 to 800°C for 2 to 6 hr to volatilize arsenic, and the final calcine 1s leached with an acid to eliminate substantially all of the remaining arsenic. A.R. Zambrano, assigned to Hanna Mining Co Jan. 29, 1980. 3 pp. (75-2). Filed. 2-13-78 (877,002).

Jan 1, 1982

By A. Rosenzweig, M. M. Karnowsky

The generalized binary diagram of the Au-Sn-Pb system is presented. The chief characteristic is the pseudobinary between lead and AuSn. On the high-gold side of the pseudobinary, four reaction isotherms were found at 363°, 274°, 225°, and 204°C. On the low-gold side of the pseudobinary, three reaction isotherms at 277°, 205°, and 176°C were found. A vertical section from the eutectic solder composition to gold was developed from the isothermal sections generated. METALLURGICAL problems arising from the intentional or accidental formation of Au-Sn-Pb alloys in soldering applications have indicated a need for information on the phase equilibria in this ternary system. The literature indicates that a complete diagram presenting this information has not been prepared. Even the recent excellent work by prince' entitled "The Au-Pb-Sn Ternary System" actually extends only to the AuSn or 50 at. pct Au range. There are more events in the 50 to 100 at. pct Au than in the less than 50 at. pct range. This article by Prince furnished much guidance in preparing this report. Initial efforts with the isopleth from the eutectic solder composition 61.9 wt pct Sn-38.1 wt pct Pb and 0 to 90 wt pct Au indicated that extensions of the work to the whole of the diagram (even if in less detail) were necessary to understand this system. In undertaking the construction of such a diagram, this study used differential thermal analyses (DTA) and metallography with verification and identification of phases by electron microprobe analyses. EXPERIMENTAL PROCEDURE The procedure began with the development of a cell which would be unreactive with lead, tin, and gold, retain its strength to 1100°C, exclude oxygen, and also furnish a suitable well for insertion and protection of a thermocouple to monitor temperature changes in the material. Such a cell would make it possible to reuse the sample should a repetition of determination be desired. Fig. 1 is a photograph of two such quartz cells as finally developed. The specimens have been run many times. The cell is made up of an inner sample bucket and an outer capsule with a thermocouple well which the sample surrounds. The DTA unit was an assembly devised from available instrumentation. The sample holder was a 3-in.-long cylinder of nickel, 2 1/2 in. in diam, fitted securely in a vertical tube furnace. Two holes 7/8 in. in diam were symmetrically located to receive the quartz cells. A dummy cell with nickel powder was used as the reference. The absolute temperature was recorded with a Pt/Pt 10-pct Rh thermocouple with an automatic Kaye ice bath compensator. (Calibration indicated the compensator to be accurate to better than ±0.5° over the 100° to 1000°C range.) The absolute temperature was measured in the sample and recorded on an L&N mul-tirange recorder with a full-scale display of 1 mv and automatic ranging of 99 mv. The differential signal between the sample temperature and the reference temperature was amplified with an L&N microvolt amplifier and recorded on an L&N Speedomax G recorder. Since two charts were obtained, the chart speeds were equalized and each event was noted on the differential chart, and the temperature at that time was obtained from the temperature record.

Jan 1, 1969