Search Documents

By Albert Sauveur

As director of the Division of Metallurgy of the Technical Section of the Air Service, American Expeditionary Forces, from August, 1917, to January, 1919, I devoted much time to the study of the steels best suited to the construction of aircraft. It became apparent at a very early stage of my investigation that the practice of builders varied greatly in regard to the number of different steels to be used, to the kinds of steels, and to their treatment. Some manufacturers employed as many as fifteen steels while the builder of one of the newest motors, favorably passed upon in the United States, assured me that two or, at the most, three kinds of steel were all he needed to produce satisfactory results. In the matter of treatment, the manufacturers were also greatly at variance. Some treated their steel with considerable refinement while others paid but scant attention to this feature. Some manufacturers case-hardened many parts, while others used the case-hardening process sparingly, if at all. Nickel-chromium steels were used at some works for case-hardening while at other plants this treatment was applied exclusively to carbon steels. Air-hardening nickel-chromium steel was used extensively by some and not at all by others. Considerable variance existed likewise in regard to the steels used for admission and exhaust valves. The conclusion was obvious, that no two manufacturers of airplane motors held like opinions as to the steels to be used or as to the treatment they should receive. Was it to be inferred from this that the many committees and associations that had been created, in part at least, for the standardization of aircraft steels had failed to make proper recommendations or that the manufacturers had ignored their recommendations ? Confining our inquiry to the committees and associations that had dealt with this question in England, France, and the United States, it was found that in Great Britain the British Engineering Standards Committee, now the British Engineering Standards Association, had devoted much time to the problem of satisfactory standards for aircraft steels. In April, 1918, this Association presented a set of specifications described as "British Standard Specifications for Aircraft Steels for Government Purchases in the United States of America." They included twenty-one different steels and, as the title indicates, were drawn for the

Jan 1, 1920

By AIME AIME

FEW men are better known in fuel engineering circles in the Middle West than the present Chairman of the Coal Division of the A.I.M.E. - Julian Elnathan Tobey. Now vice-president in charge of engineering of Appalachian Coals Inc., of Cincinnati, he has served that pioneer regional marketing agency since Aug. 1, 1934, when he became manager of its engineering department. His duties have included field promotion work in the interest of use of the agency's coals from eastern Kentucky and Tennessee, south western Virginia, and southern West Virginia in new plants of all types. He has been especially interested in certain industries which have shown an alarming tendency to change to natural gas or hydroelectric power; also in the development and practical application of small stokers and other mechanical equipment.

Jan 1, 1941

By T. C. Boberg, R. B. Lantz

This paper presents a method for calculating the producing rate of a well as a function of time following steam stimulation. The calculations have proved valuable in both selecting wells for stimulation and in determining optimum treatment sizes. The heat transfer model accounts for cooling of the oil sand by both vertical and radial conduction. Heat losses for any number of productive sands separated by unproductive rock are calculated for the injection. shut-in and production phases of the cycle. The oil rate increase caused by viscosity reduction due to heating is calculated by steady-state radial flow equations. The response of successive cycles of steam injection can also be calculated with this method. Excellent agreement is shown between calculated and actual field results. Also included are the results of several reservoir and process variable studies. The method is best suited for wells producing from a multiplicity of thin sands where the bulk of the stimulated production comes from the unheated reservoir. The flow equations used neglect gravity drainage and saturation changes within the heated region. INTRODUCTION This paper presents a calculation method which can be used to predict the field performance of the cyclic steam stimulation process. The calculation method enables the engineer to select reservoirs that have favorable characteristics for steam stimulation and permits him to determine how much steam must be injected to achieve favorable stimulation. While the calculation represents a considerable simplification of physical reality and the results are subject to numerous assumptions which must be made about the reservoir, it has been found that realistic calculations can be made of individual well performance following steam injection. The duration of the stimulation effect will depend primarily on the rate at which the heated oil sand cools which, in turn, is determined by the rate at which energy is removed from the formation with the produced fluids and conducted from the heated oil sand to unproductive rock. A complete mathematical solution to this problem is a formidable task, and finite difference techniques would undoubtedly have to be used. The calculation method pre- sented here utilizes analytic solutions of simple related heat transfer and fluid flow problems. The method is sufficiently simplified that it can be used as a hand calculation, although the calculations are somewhat lengthy and laborious. For that reason, the analysis was programmed for an IBM 7044 digital computer. Well responses observed at the Quiriquire field in eastern Venezuela&apos; have been matched using this program after making suitable approximations for reservoir and wellbore conditions. One of the most valuable uses of this calculation method is to assess the effect of reservoir and proc-cess variables on the stimulation response. This paper contains results of several studies made of key reservoir and process parameters. Among the most important of these is the influence of prior wellbore permeability damage. If a well is severely damaged prior to stimulation, a higher stimulation response will be observed than if it is undamaged. If a portion of this damage is removed, a permanent rate improvement will occur. THEORY I)ES(:KJJ&apos;TION OF CALCULATION METHOD The process of cyclic steam stimulation is essentially one of reducing oil viscosity around the wellbore by heating for a limited distance out into the formation through the injection of steam. Suitable modifications of the calculation technique presented here can be made so that stimulation of wells by hot gas injection or in situ combustion can also be calculated. A schematic drawing of the heat transfer and fluid flow considerations included in the calculation method is shown in Fig. 1. In brief, the calculation assumes that the oil sand is uniformly and radially invaded by injected steam. For wells producing from several sands, each sand is assumed to be invaded to the same distance radially. In calculating the radius heated rn energy losses from the wellbore and conduction to impermeable rock adjacent to the producing sands are taken into account. After steam injection is stopped, heat conduction continues and oil sands with r < ra cool as previously unheated shale and oil sand at r > r, begin to warm. The effect of warming of oil sand out beyond r, has little effect on the oil production rate compared to the effect of cooling of the oil sand nearer the wellbore than ra. Thus, in computing the oil production rate, an idealized step function temperature distribution in the reservoir is assumed where the original temperature exists for r > rn and where an average elevated temperature exists for r < rn. The average temperature in the oil sand for the region r < rn is computed as a function of

Jan 1, 1967

By N. T. Burdine

Formulas for calculating relative permeability from pore size distribution data are derived from basic laws of fluid flow ill porous media. The tortuosity factors that appear in the equation5 are described in. terms of the physical properties of tile medium and the saturations of the contained fluids. Procedures for calculating and methods for measuring the tortuosity factors are discussed. Values of relative permeability calculated by the formulas art: compared with results obtained by experimental measurements I INTRODUCTION Recently, several investigators have derived relative permeability equations from Darey&apos;s and Poisenille&apos;s Laws in which some, physical factor or factors describing the porous system appear. The factor that has caused the greatest amount of comment, and which is probably least understood, is the tortuosity of the fluid {lath ill the porous sample. Values of the tortuosity factors appearing in the equations range from a constant for all condition- of the fluid flow system to an inverse function of the pore radii. It is the purpose of this paper to compare wine experi~i~cntslly determined relative permeability curves with those calculated by a method which utilized capillary pressure infortmation. The capillary pressure data were obtained prefer.. ably from pore size distribution information as determined by mercury injection but. in some cases, in the absence of suitable mercury injection information. data were taken from measurements made by the porous semi-permeable diaphragm method. The physical significance of certain tortuosity concepts is inferred and the determinations of the tortuosity factors from pore size distribution data and by electrical measurements are discussed. THEORETICAL BACKGROUND In previously reported studies on pore size distribution in petroleum reservoir rocks. by the author and co-workers ail equation was derived relating specific permeability. k, to pore entry radii, R, porosity. . tortuosity factor. .,, and incremental pore volume. V. The equation is where being the "effective" length of the flow path in the porous sample. and L the length of the porous sample., The constant. 0.126. is a units conversion factor. (This definition of tortuosity factor X, = L L does not conform to all such definitions found in the literature. Fly similarity, in a two-phase system. the effective permeability of the wetting-phase.

Jan 1, 1953

By R. G. Davies

The activation energy for steady state creep above -500°C is observed to be independent of the applied stress although it varies from -67 kcal per mole at 2 at. pct Si to -100 kcal per mole at 11 at. pct Si due to changes in crystallographic order. The magnitude of the activation energy, by comparison with Fe-A1 alloys, indicates FeSi type of order in certain alloys. X-ray results confirmed the presence of FeSi type of order. It is proposed that dislocation climb is the rate controlling mechanism for all the alloys. It has been demonstrated that when a diffusion mechanism is the rate controlling process, the formation of a superlattice in brass,1 Fe3A1,2 Ni3Fe,3-5 and Feco6 1) increases the creep resistance, and 2) increases the activation energy for steady state creep. Furthermore, a study of creep in Fe-15 to 20 at. pct A1 alloys7 has revealed that as the alloy composition approaches the long-range order field, there is an increase in the activation energy for steady state creep which is thought to be due to an increase in short range order. Fe-A1 and Fe-Si alloys are similar in that they both form the DO3 superlattice in which aluminum or silicon atoms have only iron atoms as first and second nearest neighbors. There are, however, two important differences between the alloy systems: 1) The superlattice formation at -350°C commences at -10 at. pct si8 as compared to -20 at. pct Al,9 and 2) Fe-A1 alloys form a FeAl (B2 type) super-lattice where aluminum atoms have all iron first nearest neighbors even at 22 at. pct Al, but so far no similar FeSi superlattice has been observed. With the similarity between Fe-A1 and Fe-Si alloys in mind, alloys of iron with 2 to 11 at. pct Si were examined for variations with composition of the activation energy for steady state creep and of creep strength. The temperature range of greatest interest was above 1/2 TM (TM is the absolute melting temperature) where it is usually observed that diffusion is the rate controlling process. A subsidiary X-ray investigation of the Fe-Si system was undertaken in an attempt to define the position of the order-disorder boundary as a function of cooling rate. EXPERIMENTAL DETAILS a) Creep. Specimens whose gage length was 1.5 in. and with a cross-section 0.04 by 0.08 in. were strained in tension by a lever-arm arrangement, and the load was adjusted between each creep test to maintain constant stress. The apparatus and mode of operation have been fully described in a previous publication.7 As each test produced a creep strain of 0.25 pct, the variation in stress during the test was negligible. Creep strain was measured at the end of one of the alloy steel grips by a displacement transducer with the out-of-balance potential being recorded on a variable speed recorder. The full-scale deflection of the recorder could be varied in steps to give limits of sensitivity of between 0.1 and 0.001 pct creep strain. The alloys, Table I, were made available by the Metallurgical Department, National Physical Laboratory (N.P.L.), england,10 and by the Research Department, General Electric Co. (G.E.), Schenectady, N.Y. They were hot worked at -850°C, warm worked at 550° to 650°C, and recrystallized in vacuum at -750°C to give a grain diameter of -0.1 mm. All the alloys had a very low impurity content; those from the N.P.L., for which a complete analysis is available,&apos;&apos; show carbon less than 0.026 pct, manganese less than 0.006 pct, and oxygen plus nitrogen less than 0.0024 pct. b) X-ray Procedure. A General Electric XRD-5 X-ray set with a focussing lithium fluoride mono-chromator in the diffracted beam, and a pulse height analyzer to eliminate harmonic wavelengths of the cobalt radiation, was used to investigate the structure of several very fine grained (grain diameter <.01 mm) Fe-Si alloys after the following heat treatments: 1) Quenched from 700°C, 2) slow cooled from 650°C (-40°C per hr), and 3) very slowly cooled from 400° to 100°C (10°C per hr with a 24 hr anneal every 100°C). The method of obtaining the diffraction pattern over the range of 20 from 15 to 45 deg was to count for at least 100 sec every l/3 deg with a slit subtending 1 deg in 20 at the focus; the probable counting error was less than 2 pct.

Jan 1, 1963

By David White

THE environmental conditions under which coals are deposited are revealed by the stratigraphy of the coal basins and coal beds and by the details of the structure and the physical constitution of the coals themselves. THE LAND SURFACE Generally Low Relief or Base Level In the Paleozoic coal fields, which have longest been worked, are most important, and are best known, we find relations, in general, as follows A post-Mississippian uplift with, in most cases, very moderate deformation, followed by erosion by which the uplifted regions, especially the bolder of the new topography, were largely worn down, while the older and less deformed regions were more or less extensively base leveled. Base leveling of most of the region continued as the deposition of coal measures proceeded. Consequently, in most coal fields the Pennsylvanian, or upper Carboniferous, lies unconformably on the Mississippian or on older formations. There are but few regions in which sedimentation is seen to have been apparently continuous from the Mississippian into the Pennsylvanian ("Coal Measures").

Jan 1, 1925

By H. P. Greenwald

THIs paper brings forward a discussion that was prepared for the meeting of the Coal Division in Chicago in 1938.1 War in Europe less than a year after that meeting, followed by our defense preparations and entry into the conflict, caused general cessation of large-scale experimentation on the subject, and it is best to confine this paper to events in the United States during the five-year period since the preceding paper was written. The views of members of the Coal Division&apos;s Committee2 on Rock-dust-ing for 1943 were obtained before this paper was written and the manuscript was reviewed by them. Extent of Rock-dusting Statistics on the use of rock dust in the United States during the years 1930-1933, appearing on page 97 of Volume 139 of the Transactions are extended in Table I herein through the year 1941. The results through 1933 did not appear encouraging, but there has been improve-ment since that date. It has always been true that the larger operations were the ones that used rock dust. In 1941 only 10 per cent of the mines in the country used rock dust, but they produced 57 per cent of the coal, employed just under 50 per cent of the miners, and accounted for 52 per cent of the man-hours. Unfortunately, collection and compilation of these statistics are slow procedures, and figures dealing with the tremendous war expansion of the industry are not likely to be available for a year or more. In 1941 the five leading states in regard to percentage of man-hours worked in mines using rock dust were: Utah, 92.1; Wyoming, 79.3; Alabama, 77.4; New Mexico, 72.5; West Virginia, 65.3. The first four states were the same as in 1933, but West Virginia displaced Washington in fifth place. On the basis of pounds of rock dust used per ton of coal, the five leading states in

Jan 1, 1944

By H. P. Greenwald

THIs paper brings forward a discussion that was prepared for the meeting of the Coal Division in Chicago in 1938.1 War in Europe less than a year after that meeting, followed by our defense preparations and entry into the conflict, caused general cessation of large-scale experimentation on the subject, and it is best to confine this paper to events in the United States during the five-year period since the preceding paper was written. The views of members of the Coal Division&apos;s Committee2 on Rock-dust-ing for 1943 were obtained before this paper was written and the manuscript was reviewed by them. Extent of Rock-dusting Statistics on the use of rock dust in the United States during the years 1930-1933, appearing on page 97 of Volume 139 of the Transactions are extended in Table I herein through the year 1941. The results through 1933 did not appear encouraging, but there has been improve-ment since that date. It has always been true that the larger operations were the ones that used rock dust. In 1941 only 10 per cent of the mines in the country used rock dust, but they produced 57 per cent of the coal, employed just under 50 per cent of the miners, and accounted for 52 per cent of the man-hours. Unfortunately, collection and compilation of these statistics are slow procedures, and figures dealing with the tremendous war expansion of the industry are not likely to be available for a year or more. In 1941 the five leading states in regard to percentage of man-hours worked in mines using rock dust were: Utah, 92.1; Wyoming, 79.3; Alabama, 77.4; New Mexico, 72.5; West Virginia, 65.3. The first four states were the same as in 1933, but West Virginia displaced Washington in fifth place. On the basis of pounds of rock dust used per ton of coal, the five leading states in

Jan 1, 1944

By E. D. Gardner

INTRODUCTION OIL shale deposits have been exploited in various countries throughout the world, but generally with government aid. The oil-shale industry of Scotland perhaps is the oldest and best-known; the largest was conducted in Manchuria by the Japanese during World War II as a source of liquid fuels for military uses. In general, foreign oil-shale deposits that have been exploited are much lower grade than those in the western United States. Considerable interest began to be shown in western oil shales in 1916; the peak of activities was in 1923. The Catlin operation, near Elko, Nevada, perhaps was the nearest approach in this country to an oil-shale enterprise on a commercial scale. Over 100 companies were formed, ostensibly for exploiting the oil shale; a large number of them, however, proved to be stock promotions only, which gave the embryo industry a black eye. The Bureau of Mines operated an experimental oil-shale retort plant near Rifle, Colorado, from September 1926 to June 1927 and again from April 1928 to July 1929, after which the plant was dismantled. By this time the East Texas oil fields had come in and the country lost interest in substitute liquid fuels. During World War II the Nation again became concerned about the magnitude of its petroleum reserves. Congress (April1944) directed the Bureau of Mines to build and operate demonstration plants to produce synthetic liquid fuels from coal, oil shales, and agricultural and other products; a five-year program was authorized. As a part of this program the Bureau of Mines has built, at Anvil Points near Rifle, Colorado, a retort plant and developed an experimental mine to supply the plant with oil shale. An important part of the mining work at Rifle is to devise methods and select practices for mining the oil shale on a commercial scale at the lowest practicable cost. The product to be mined has a relatively low value, a fact that must be kept continuously in mind. The combined aim of those in charge of the mining and those in charge of retorting is to demonstrate that the shale oil can be produced at a cost per barrel corresponding to the current quotation for crude petroleum -or at least very close to it. Plans call for an uninterrupted flow of broken oil shale from the face in the mine, through crushers, through the retorts and thence to the disposal dump. The disposal of the spent shale in the Rifle area should present no unusual problem. Mining research has consisted so far of paper studies of the general phases of the problem, determination of the widest span that the roof stone will stand safely unsupported, and drilling problems. Underground development has not proceeded far

Jan 1, 1947

By J. Mizrahi, A. Brillantshtein, A. Mitzmager, O. Schächter

The separation of synthetic mixtures of heavy minerals by hindered settling classification and jigging was comparatively tested in water and five organic heavy liquids, of various specific gravities and viscosities. It was found that in the hindered settling classification process the separation efficiency was directly proportional to the concentration criterion, the liquid viscosity being a minor factor. There is therefore a decisive advantage in using heavy liquids as classification medium. In the jigging process the advantage of using a heavy liquid is masked by the detrimental effect of a higher liquid viscosity, which, in this case constitutes an important factor. Considerable interest has been aroused lately by the development of mineral beneficiation techniques 1,2 using TBE (tetrabromoethane), a heavy liquid of specific gravity of 2.96, which has been made available for industrial use by a new process3 producing TBE directly from the Dead Sea brines at a reasonable price. Most of the applications investigated until now were based on the sink-float separation of minerals in a heavy liquid of intermediate specific gravity. The TBE can be conveniently diluted with many organic solvents, and thus sharp separations are possible in a wide range of specific gravities up to 2.96. Although this maximum specific gravity is sufficient on most cases for the elimination of the bulk of the barren gangue and the production of marketable concentrates, some practical problems came up for investigation in which the separation of two (or more) minerals, heavier than TBE, was required.* *Among the cases studied in the IMI Laboratorles which fall into this category we can mention: alluvial deposits, such as heavy minerals in sea sand, tin deposits, or ground coarse-grained rocks, such as pegmatites. In such cases where, due to the petrographic structure, further fine grinding is required in order to achieve the liberation of the heavy components, the

Jan 1, 1964

By H. M. Chance

The present value of most coal properties resides largely in the cod remaining to be mined, which thus constitutes the most important asset. The object of this paper is to discuss methods commonly used in computing the value of minable coal. To distinguish clearly between such coal values and the values of other property, the several kinds of property values should be divided into classes; so as to avoid the unintentional omission of items of importance. Value op Coal Reserves Judicial decisions prescribe, and appraisers commonly accept, current sales value as the preferred means for determining the value of transferable property. With few exceptions a property is worth the sum that can be realized from its sale by a willing seller to a willing buyer, a sale in which compulsion urges neither party, and between whom there is no community of interest to fix a value; or it is worth at least as much as a responsible buyer will offer for it. Actual sales of like property or bids from responsible buyers for the property, or for substantially like property, are the best established methods for determining values. Only in the absence of such sales or bids can valuations by other methods be entertained, and only for reasons of weight can sales values be set aside. Valuation Based on Royalties Sales of coal in the ground, as customarily carried out through lease under royalty agreements, are therefore the most trustworthy means available for determining the value of coal reserves. The constantly rising value of high-grade coal in the United States can most readily be shown by the increasing royalties per ton that can be obtained for such coals under leasehold. The rising value of land containing such coal can also, of course, be proven by the price at which such properties are actually sold as compared with prices obtainable for lands containing coal of the same grade in the past. It is exceedingly difficult, however, to establish values by the prices paid for coal

Jan 1, 1927

By Arthur F. Taggart

RECENT jig practice has shown such marked departures from the pronouncements of the textbooks, particularly as to particle size recovered and size range of feed, as to make it desirable to reexamine the mechanism of jig action. This paper presents the results of such a study. The general conclusions of the paper are: I. A jig bed is a bi-functioned as well as bi-parted body. The upper layer comprises a plastic stream moving slowly in a substantially horizontal direction from feed lip to tail board. It serves to rough out tailing and light middling and to pick up heavy middling and lift it out of the jig box. The lower layer acts as the ultimate separating means by absorbing concentrate and rejecting heavy middling. 2. The separating function of the lower layer is performed in three definitely different ways, depending upon the relative sizes of the grains presented to it and those composing it. EXPERIMENTAL The experimental work consisted of close and long-continued visual observations of operating beds in a plunger jig, eccentric driven, and in determinations of the settling rates of various metal spheres through a quartz bed under various conditions of operation. Falling velocities were measured by an ingenious method devised by A. C. Dorenfeld, a student in the Mining Department at Columbia. Spheres of different metallic alloys, Y8-in. diameter, were cast with a short piece of fine copper wire frozen in to serve for suspension. A short piece of black cotton thread was looped to the top of the wire to serve as an indicator. The set-up for a test is shown in Fig. I. The thread should be boiled, if necessary, to make it freely water absorbent. The piece of clean plate glass D is supported rigidly at the proper height in a vertical position. The white scale E is similarly supported behind the glass. At the beginning of a test, D is filmed with water by holding it (best with clean rubber finger cots) under running tap water. It is then clamped in approximate position and C, already wet, is laid across it and drawn straight and vertical with the upper end at or near the top of D, and the ball A slightly above the top of the expanded bed. The water film holds the string to the glass. For a test the string is released, its upper end position noted just after the top of the ball becomes submerged, when the corresponding time is read, and thereafter simultaneous readings of position and time are taken as desired. Results of the visual studies of the bed are given at the pertinent places in the following discussion. Results of the settling tests are summarized in Figs. 2 and 3. DEFINITIONS The name bed as used herein refers to the entire mixture of solids and water filling the jig box. A layer is a stratum of a bed composed of particles of substantially the same specific gravities. A granular product is long-range when it approximates a crushed or ground product limited as to upper size only; a shorlrange product is one closely sized. A bed is loaded when operating with continuous feed

Jan 1, 1943

By R. L. Ash, R. R. Rollins, C. J. Konya

An investigation was performed to determine conditions for optimizing the spacing of simultaneously initiated multiple explosive columns. This was done by using models of mortar, dolomite, and Plexiglas with 10-grain mild detonating fuse as the explosive charge. It was desired to simulate blastholes with multiple primers initiated by detonating fuse or when high-velocity explosives are used in low-velocity materials. It was found that optimum spacing between multiple charges was strongly influenced by charge length. At less than optimum charge length, the spacing at which complete shearing was possible between adjacent charges decreased exponentially with a subsequent loss of broken material volume. For charges fired simultaneously, larger burdens and spacings were possible as compared to those necessary for single-crater charges. For each material studied, there was a characteristic optimum charge length and a maximum attainable spacing at any given burden. Proper selection of the spacing distance between charges is fundamental to successful blasting. Its value directly affects the cost of drilling and explosives used per unit of broken material. In addition, the choice of a spacing that is Compatible with a given set of blasting conditions aids in the control of fragmentation sizing, ground vibrations, overbreak, and throw which in turn, influence other production costs. For example, normally loaded blastholes that are spaced too closely invariably promote overbreak and usually give coarse fragmentation. Unless care is taken, airblast and violent flyrock will occur and under certain conditions cutoffs and misfires may result. Too large a spacing, on the other hand, frequently leads to conditions that form bootlegs or toes. The choice of a particular spacicg to use, however, is largely a matter of individual experience and judgment, usually based on trial and error. Very little is known or can be found in the literature with regard to how the spacing between charges is related to field conditions and charge geometry. As a general rule, the firing time sequence of adjacent charges and properties of a material are thought to have the most significant influence on the spacing distance best suited for any given field condition. For example, delayed initiation of adjacent charges usually always requires a closer spacing than when charges are fired at the same time. This should be expected if one considers that the energy normally dissipated and lost in the surrounding ground from charges fired independently would be captured and utilized for breaking material between charges when they are initiated together. Spacing can be extended also when charges are aligned with structural planes of a material, such as jointing, along which shearing is relatively easy. It is customary to relate the spacing (S) between charges to their common burden (B) in the form of a spacing ratio, or SIB. The burden normally is considered as the optimum depth or distance from any single charge perpendicular to the nearest free or open face at which the desired fragmentation and maximum crater yield are obtained. For production blasting, value of the ratio is generally considered to vary from 1 to 2, depending on conditions.1-6 When adjacent charges are fired independent of one another, the value varies from 1 to about 1.4, the closer amount being employed to square corners or produce craters having the ideal 90" apex angle. The larger ratio is the geometric balance value for craters having an apex angle of 135". The basic ideal crater forms in the plane of the charge diameter for charges fired independently are shown in Fig. 1. In the event charges are fired simultaneously, geometric balance in the plane of their charge diameters suggests that a spacing ratio near 2 would be appropriate, as illustrated by Fig. 2. In practice, however, some compromise ratio value must be selected to conform with the specific ground conditions. An example would be where the jointing planes tend to produce 60° or 120° crater angles, the appropriate geometrically balanced charge arrangement being given by Fig. 3. In this condition, the spacing ratio is 1.15, not 1 or 1.4 as suggested for the 90° cratering of independently fired adjacent charges. In view of the foregoing, it would seem logical to assume that whenever charges all having the same burden are fired at the same time, spacing distances always can be greater than those permitted by charges fired independently. In practice this is not the case, however.

Jan 1, 1970

By Shiou-Chuan Sun

THERE are several postulations for the mechanism of slime-coating. Ince1 proposed the electrostatic hypothesis, del Giudice2 suggested the chemical theory; Bankoff3 reported that slime-coating is inhibited whenever the surfaces of the slime particles are ionized sufficiently for Brownian movement to occur, and is facilitated when they are not. These postulations were examined by experiments involving the Burton tube, the cataphoretic cell, and slime-coating. The techniques involved will be described elsewhere in this paper. The electrostatic hypothesis, supported by migration experiments in a Burton tube, was abandoned by del Giudice.2 Experiments of mineral migration in a Burton tube, after the idea of Ince with modification, indicated that this apparatus was inefficient for accurate observation. A cataphoretic cell was constructed. The experimental data, as shown in this paper, enable the correlation and advancing of this hypothesis. Del Giudice&apos;s chemical hypothesis considered that slime particles are attached to the galena surfaces by a cement formed as the result of a metathetical reaction between the sulphide and the slime particles. Applying this hypothesis, the calcite slime particles were cemented to the galena surface by the formation of a cementing lead carbonate. In a similar way, lead silicate was considered as the cement of quartz slime coating on galena. Experiments verifying this hypothesis were carried out according to the following procedure: Fresh mineral particles selected from the central part of the broken lumps and examined first under a microscope for ascertaining a clean surface were placed in a small beaker (1.5-in. dia. by 2.5 in. deep) half filled with one kind of slime pulp. The dilution of all slime pulp was 4: 1 and the particle size of slime was minus 400-mesh. After agitation for 5 min. the specimen was removed by a sharp-end tong and washed gently three times in three separate distilled water baths. It was dried before a small electrical fan and examined immediately under a microscope. A photograph was made of the observation. With reference to the published solubilities,4 several of these experiments, which contradict the chemical hypothesis, are listed as following: I. The coating of fluorite slime on the galena surface was light but the coating of galena slime on the fluorite surface was heavy. In a similar way, the coating of quartz slime on the galena was fairly light, but the coating of galena slime on the quartz particle was heavy. According to the chemical hypothesis, using the same constituents and regardless of which is the slime, the density of the coating should be expected to be the same. This, however, as shown above, is not true. Moreover, fluorite (CaF2), having a solubility of 16 mg.[4a] per liter of water, should not be

Jan 1, 1943

By J. W. Spretnak, V. Kandarpa, G. W. Powell, R. A. Erickson

Neutron-diffraction pattens were obtained at room temperature from two austenitic manganese steels, oxc wth n carbon content of 1.23 zct PC/ and the olher 0.63 wt pct. Analysis of the data showed that the curOan atols (ions) occupy tile octaheadral site. any of the cavbon is in the tetahedral site, tile concentration is too strzall lo be detecled by tzeulr-on d$facton. AS part of a long-range investigation of eutectoid decomposition, a study of the structure of austenite has been undertaken in order to characterize as best as possible the parent phase in the Fe-C system. Austenite is a solid solution of carbon atoms in fcc iron, the carbon atoms being located in interstitial positions. Of the two kinds of interstitial sites, octahedral (0, +, +) and tetrahedral (4, a, $), in this lattice, the larger octahedral sites are usually considered as the probable position of carbon. The strain energy involved in pytting a neutral carbon atom (covalent di; ameter 1.54)&apos; into a tetrahedral site (diameter 0.56A) is considerably greater than that associated with p2tting carbon into the octahedral site (diameter 1.08A). Dayal and arkeen&apos; observed the migration of carbon in iron under the influence of an electric field indicating tha tye carbon is ionized. pe ionic radius of C&apos;4 is 0.15A and that of C" is 0.29. Consequently, it is conceivable that carbon ions could occupy the tetrahedral sites if one considers only the strain energy. Size considerations alone do not provide a complete explanation for the formation of the interstitial solid solutions, however. because metals such as copper, zinc, and cadmium do not appear to form interstitial solid solutions in spite of their large interstitial sites. Evidence which suggests partial ioni-zation of the carbon in austenite has also been obtained by Speiser, Spretnak, and alor who derived formu- lae relating the observed change in lattice parameter to the effective diameter of the solute atom. Assuming the carbon occupies the octahedral site. they computed the effective diameter of carbon to be 1.33A whereas the covalent diameter is 1.54A. petch5 concluded from powder X-ray diffraction experiments that carbon atoms occupy the octahedral sites. His conclusion was based on the general trend observed in the intensity of the diffraction lines as the carbon content of the austenite was increased. However, the major difficulty associated with application of X-ray diffraction to this particular problem is the relatively poor scattering power of carbon. Williamson and smallman&apos; utilized X-ray diffraction to study the line broadening caused by the strain field about carbon atoms inferrite: these investigators concluded that at least 85 pct of the carbon in ferrite occupies the octahedral (0: 3, B) site rather than the larger

Jan 1, 1967

By H. W. Camp

Research is defined, scientifically, as a "systematic investigation of some phenomenon, and also a search for hidden treasures." Chemists tell us that the hidden treasures of petroleum are far richer than the products which have been best known to us. However, these secrets will be discovered only through intensive and systematic, as well as scientific, industrial research. Indeed, the scope of the subject is so great that such an intensive research program should be assumed by a centralized organization supported by the petroleum industry as a whole. Such organization should assume the responsibilities for investigation of new products and development of markets for such products. Gasoline, the chief product of the petroleum industry has become a cheap commodity. The continual uncontrolled overproduction of crude petroleum, the intensive competitive condition in the marketing of petroleum products and the increase of refining efficiency and installing of cracking facilities, have all combined to lower the market value of gasoline. The purchaser has profited from the lower cost of gasoline by way of lower prices so that today the most important product can scarcely be manufactured at a profit. In other fields, manufacturing industries have diversified their products when faced by a similar situation. Thus, they have been able to widen their marketing outlook. Why cannot the petroleum industry employ the same tactics? Right now we are hearing much discussion concerning the development of a wider market for existing petroleum products and new products for existing or prospective markets. For instance, we can cite recent developments for use of propane, butane and ethylene. Butane has been found to be an efficient and inexpensive refrigerant, especially adapted to home refrigerating systems. Propane and butane fractions of natural gasoline may be shipped under pressure and may be used as a substitute for, acetylene in cutting torches in connection with oxygen. There is a possibility of substituting butane for gas oil in the carburation of coal gas, as we know that butane contains practically the gas enrichment as the same volume of gas oil and should prove to be a superior product for

Jan 1, 1928

By D. B. Robinson, C. A. Macrygeorgos, G. W. Govier

Experimental data have been obtained on the volurrletric behavior of ternary mixtures of methane, hydrogen sulfide and carbon dioxide at temperalures of 40°, 100" and 160°F up to pressures of 3,000 psia. The results indicate that the compressibility factors for this system do not agree with compressibility factors for sweet natural gases at the same pseudo-reduced conditions. The deviation increases as the temperature and methane content decrease. Discrepancies of up to 35 per cent were observed. A careful analysis has been made of the existing pUrblished data on compressibility factors for binary systems containing light hydrocnrbons and hydrogen sulfide or carbon dioxide. It has been found that the deviation of actual from predicted compressibility factors for methane-acid gas mixtures is a function of the methane content and the pseudo-critical properties,.v of the mixture. The ratio between actual compressibility factors for methane-acid gas mixtures and compressibility factors for sweet natrlral gases at the same pseudo-reduced conditions has been currelated over a range of pP,, from 0 to at least 7 arid a range of pT, from about 1.15 to at 1east 2 0 with an error not exceeding 3 per cent and over most of the range within I per cent. The validity of the correlation for mixtures containing appreciable hearvier hydrocorbons has not been fully established, but it is shown to be preferable than the use of a corretation based only on hydrocarbons. INTRODUCTION Although a relatively accurate method for predicting compressibility factors of pure materials is provided by charts based on reduced properties and the assumption that the compressibility factor is a unique function of T P and z the determination of the correct values of compressibility factors for gas mixtures is somewhat difficult. Two general methods of dealing with gaseous mixtures have been proposed. The first assumes a direct or modified additivity of certain properties of the mixture in terms of the properties of the individual components. Examples of this method are based on the familiar laws of Dalton and Amagat. The second method averages the constants of an equation of state applicable to the pure components. Both of these methods are of limited value in engineering calculations because the first usually provides reliable answers only over narrow ranges of pressure and temperature and the second is cumbersome to handle. In petroleum engineering practice accurate estimations of the volumetric behavior of natural gases arc frequently required. To fulfill this need, several generalized compressibility charts have been developed.&apos; &apos; Of these, the one prepared by Standing, el al is widely used at present. In the construction of charts of this type a third method for dealing with mixtures has been followed. It is based on correlation of pseudo-critical properties as outlined by Kay and calculated from the critical properties of the individual components in a mixture. Although these charts provide relatively accurate information on the compressibility of dry or wet sweet natural gases, they are less reliable when used for gases containing high concentrations of hydrogen sulfide or carbon dioxide or both. Thus, an experimental program, although time consuming, is the best means now available for the determination of the volumetric behavior of sour or acid gas mixtures. An increased interest in the behavior of these gas mixtures, particularly in connection with some of the fields in Western Canada where the acid gas concentration of the reservoirs may be as high as 55 per cent and where hydrogen sulfide alone may be as high as 36 per cent, provided the incentive for this study. It was the purpose of the investigation to determine the volumetric behavior of selected mixtures of methane, hydrogen sulfide and carbon dioxide over a range of temperature from 40" to 160°F and at pressures up to 3,000 psi. EXPERIMENTAL METHOD The apparatus used in this investigation was basically the same as that described by Lorenzo.&apos;" The amount of each pure component used in preparing the gas mixtures was measured over mercury in a glass-windowed pressure vessel. The pure components were then transferred individually in the desired amounts to a second glass-windowed pressure vessel where the volumetric behavior of the mixture was determined. Volume was varied by mercury injection or withdrawal. The capacity of the cell was about 125 cc. Temperatures in the cells were measured with copper-constantan thermocouples and a Leeds Northrup semi-

By Louis A. Carapella, Ralph Hultgren

WHEN F. Heusler1 found in 1898 that certain alloys containing only copper, manganese, and tin were ferromagnetic, the discovery excited a great deal of interest and led to numerous investigations. It was early found that tin could be replaced by aluminum, arsenic, antimony, bismuth, or boron without destroying the ferromagnetic nature of the alloys.2 Copper may also be replaced by silver.3 All these alloys have come to be known as "Heusler alloys." The aluminum alloys apparently were the most magnetic and have been most extensively investigated. However, no agreement has yet been reached as to the source of the ferromagnetism arising from these nonferromagnetic elements. Absence of reliable quantitative data makes speculation hazardous. The value of much of the earlier work was vitiated by lack of necessary precautions against contamination, and by lack of close control of heat-treatment. It was only recently established that in aluminum Heusler alloys" the ferromagnetism arose from a single phase, an ordered body-centered-cubic structure. With modern methods of preparation, heat-treatment, and X-ray examination, it is possible to prepare these alloys without contamination, to heat-treat them intelligently, and to determine what phase or phases are present in the finished sample. In the present investigation, a series of pure alloys in the comparatively neglected copper-manganese-tin system have been prepared, which consist of a single, body-centered-cubic structure (the beta phase) and whose compositions vary within wide limits. The magnetic saturation values of these single-phase alloys have been quantitatively determined, so that considerable data on the effect of composition on the ferromagnetism have been made available. In the course of the investigation some information on the extent of the stability of the beta phase and the nature of phases in adjacent regions of the ternary diagram has been accumulated. Anomalies in earlier data have been explained, and alloys have been prepared that are much more strongly magnetic than any previous Heusler alloys. PREVIOUS WORK In the original work of F. Heusler1 and coworkers,2 a maximum magnetic saturation value of I = 107 was found at the composition Cu6Mn3Sn, while a value for Cu2MnA1 of I = 443 was early measured. Ross and Grays found a second maximum at the composition Cu2MnSn, which was much more magnetic than Heusler&apos;s original alloy. F. Heusler6 then reinvestigated the system, confirmed their results,

Jan 1, 1941

By William E. Ford, Edward Salisbury Dana

THIS Appendix contains a series of tables, more or leas complete, of minerals arranged according to chemical composition or to certain prominent crystallograhic or physical characters. These, it is believed, will be of service not only to the student, but ago to the skilled mineralogist. The type used in the printing of the mineral names indicates their relative importance. Table I is a complete list of the species named in this book arranged fist according to the prominent basic elements which they contain and secondly according to their acid radicals. Table II is of Minerals arranged according to their System of Crystallization The other tablets make no claim to completeness, being limited often to common ah important species. For an exhaustive system of Determinative Tables based particularly upon blowpipe and chemical characters, the student is referred to the work of Professors Brush and Pen- field, mentioned on p. 330.

Jan 1, 1922

By G. J. Dickman, W. N. Thomas

The factors involved in selecting, a drive system for a grinding mill, including gearing arrangement, motor selection, and electric-supply system limitations are reviewed. Equipment costs are evaluated on a dollar per horsepower basis and starting performance is analyzed, the latter making use of a recently developed computer program. The present interest in large-diameter grinding mills and the rapidly rising cost of the drive in proportion to the cost of the mill establishes a need to explore the drive system in detail. The drive for a 7 to 8,000 hp mill will cost from $350 to $600,000 which represents nearly half the total cost of the mill package, and requires as much building space as the mill proper. Some of the drive components require a longer time to manufacture and the installation time and costs are equal to those for the mill. It is apparent that the drive has become a dominant factor in the overall mill design consideration. A new plant requires a tremendous investment in both time and money. With the high degree of competition in the mining industry, low capital cost is an exceedingly important factor in the development of a project. It is just as important, however, to insure that the equipment is going to perform satisfactorily for the anticipated life of the project without adding unplanned operating, maintenance, and replacement costs. This is the position in which the engineer or designer usually finds himself and is really one of his primary functionsestablishing a realistic compromise between cost and performance. Large primary grinding mills can represent a major portion of the cost of a plant and the drive system accounts for a substantial part of this cost. These facts justify a careful analysis of the drive requirements and all of the factors involved in ultimately arriving at the best system for the lowest cost. A number of excellent papers have been published on various aspects of mill drives. The authors have used information from these papers in making a study of a drive for a 7600-hp, 32 x 12-ft autogenous mill. This was a broad investigation, including mechanical and electrical design, layout, performance, and maintenance considerations, and overall economics leading to the selection of the optimum system for that mill. This paper was developed from the study and includes information applicable to large mills in general. For a successful and economical application, the drive must be considered as a system and all of the components analyzed to determine their effect on the system. This requires the participation of the mill designer, gear, and other mechanical component manufacturers, motor manufacturer, plant designer, and operator. A careful analysis of the mill torque requirements is first necessary to provide a basis for selection of the mechanical and electrical drive components. Because of manufacturing limitations on the size and capacity of gearing available for these low-speed applications, an evaluation of costs for various gear ratios and configurations in conjunction with motor speeds is required. Consultation with the power-supply company is necessary to determine limitations on motor-starting disturbances and to analyze operating costs on the basis of existing rate structures and low characteristics. Finally, consideration must be given to the drive arrangement and its affect on plant layout, space requirements, and location of auxiliary equipment for the selected process. There are presently three basic schemes for driving a mill. The first is a direct drive by a motor operating at mill speed with no gearing. The second is by a higher-speed motor through a trunnion-connected gear drive. The third is by a motor through the more conventional pinion and ring-gear with the option of an interposing gear box to permit greater motor speed than pinion shaft speed. [(Fig. 1.)] Several manufacturers have or are presently developing motors which drive the mill directly without the use of gears. One arrangement has the motor armature intimately surrounding the mill shell-discharge spout or extension of the trunnion journal. The motor stator is then supported independently and surrounds the shell or trunnion-mounted rotor. Another variation utilizes an independent mill-speed motor connected to the trunnion by a drive shaft and flexible couplings.

Jan 1, 1972