Search Documents

By C. W. Hall

MINE executives, as a rule, have always been willing to adopt new ideas of operation, or to listen to proposals which might increase the effectiveness of their enterprise, more especially so if they could be shown how definite results might be attained by introducing any conception suggested. In these days of high wages, high cost of supplies, and high taxes, operators are even more inclined to accord consideration to innovations or improvements, and many go so far as to employ men to conduct special investigations and make studies for the purpose of advancing production. Where a man is brought into an organization to do work of an efficiency nature, it often creates resentment among the operative heads because of having their work directly scrutinized, or investigated, and there is a tendency, if not actually to obstruct, to fa.il to cooperate; in which case the investigator is handi-

Jan 1, 1925

By C. W. Nicolson

THE Tri-State zinc and lead-mining district is in the northeast corner of Oklahoma, the southeast corner of Kansas and the southwest corner of Missouri. The area throughout which active mining has been conducted is about 45 miles long and about 5 miles wide, extending northeasterly from Commerce, Okla., to Alba, Missouri. Although the lead ores were mined on a very small scale in the vicinity of Joplin, Mo., as early as 1848, nothing of any importance was done in the district until 1870, since when both mining and smelting have been prosecuted with considerable vigor. In the beginning the lead ores only were exploited, but within a few years extensive deposits of zinc ores were found and since that time the production of zinc ore has far exceeded that of lead. Both the surface and mineral rights in Missouri and Kansas were under individual ownership by the time ore was discovered. Although some of these rights were purchased by mining companies, most of the mining has been done under leases covering small areas, usually 40 acres, although in the past many leases were given on much smaller tracts. In Oklahoma most of the mineral land had been alloted by the Government to various Indian tribes and although the title to some of these lands had been acquired by various white men before the discovery of the rich Picher field, the title to most of the land has remained with the Indian tribes and the leasing of the mineral rights has been done by the Federal Government for the benefit of the Indians. The Indian allotments were of 200 acres each and some of the mining leases covered entire allotments, although many leases were granted for only 40 acres or even less.

Jan 1, 1938

By C. M. Weld

The southeastern coast of China, from Ning-Po to Macao, represents an element in the continental mass of Asia which has at practically all times in the remote past exhibited a tendency to rise father than to subside.

Jan 1, 1915

By John E. Young

U.S. Steel Corp.'s Winifrede mine is operated by Lynch District in the mountainous region of eastern Kentucky. This region is characterized by narrow finger ridges and precipitous slopes, which present both an opportunity and challenge in the design and selection of coal-handling facilities for the movement of coal from the section belts to the railrod cars. Lynch District selected diesel-powered locomo¬tives and 100-ton articulated cars capable of negotiating sharp curves. The drop¬bottom mine cars are equipped with longitudinally hinged doors that are auto¬matically opened and closed. Lynch District selected a large-diameter steel-lined borehole for lowering the coal approximately 1000 ft from the seam level to the valley floor railroad load-out point. Taking advantage of gravity, the presized coal is "lowered" vertically approximately 720 ft to existing entries of a previously abandoned mine. The coal is then conveyed horizontally into storage. The coal¬handling facility from the mine-car dump to the railroad load-out point is fully automatic through use of tone control. TV cameras are installed along the facility to continuously monitor the strategic points. The diesel locomotives are either directly operated or remotely radio-controlled, depending on the functions Per¬formed. U.S. Steel Corp.'s Winifrede mine is operated by Lynch District in the mountainous region of eastern Kentucky. This region is characterized by narrow mountain ridges and precipitous slopes which present both an opportunity and challenge in the design and selection of coal-handling facilities for the movement of coal from the section belts to the railroad cars. The narrow finger ridges precluded use of under¬ground haulage and, thereby, presented the opportunity to use high-capacity equipment on the outside bench. The precipitous mountain slopes, steepest at the Wini¬frede seam horizon, presented a challenge to select a solution for lowering the coal approximately 1000 ft from the seam level to the valley floor railroad load-out point. It was evident from the start of planning that these two factors predominated; namely, rail haulage and coal lowering, and solutions to these would determine the final design of the Winifrede mine coal-handling facilities. The Winifrede mine derives its name from the Wini¬frede Seam which comprises the total reserve recov¬erable from this facility. The seam is 5 ft high with a good siltstone bottom and competent shale or sandstone roof. The seam is at an elevation of 2700 ft where the mountain ridges are long and narrow. This configuration of the reserve was ideal for conveyor belt installation to transport the coal from the working face to the outside bench. The preclusion of underground rail haul¬age permitted an opportunity to review the type of locomotive power and to select high-capacity equipment without the limitations associated with underground systems. Since the basic electrical design of the mine was al¬ternating current, with rectification to direct current for shuttle cars required only in the face areas, there was no point in bearing the burden of additional cost of dc trolley installation. And, since the haulage would re¬quire only a few tunnels to negotiate sharp points and to reach the back side of the reserves, diesel power was selected for the haulage locomotives. To provide stability on the almost continuously curv¬ing track and to provide the maximum width of haul¬age equipment, both locomotives and mine cars, stan¬dard railroad gage was chosen to offer the largest choice of equipment. The decision was made to select a standard 45-ton railroad diesel locomotive but to lower the cab height to reduce tunnel excavation requirements. The mine car was the next challenge. Past experience in Lynch operations indicated that drop-bottom cars would be a successful application with the free-flowing coal. The search was for a drop-bottom car within the dimensions of the locomotive to discharge the coal in the shortest time. Numerous types were considered and visits made to various sites to observe cars in operation.

Jan 1, 1972

By H. M. Beatty, T. L. Joseph, Gust Bitsianes

SUCCESSFUL blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blast- furnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO ? 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which C02 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature com- bustion of carbon above the tuyeres. Assuming that 1000 lb. of limestone is used per ton of pig iron, about 435 lb. of C02 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb. would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1942

By A. W. Gauger

SMELTING of iron ore, manufacture of steel, and the fabrication of ferrous metal products are all processes that require energy. Charcoal was adequate, to supply this energy for the relatively simple processes of the early iron-masters. In the fourth decade of the nineteenth century, anthracite and bituminous coal and later coke supplanted charcoal for the smelting of iron. So far as the chemical phases of the process were concerned, charcoal was an ideal iron-furnace fuel. It had practically no sulphur, and its ash, besides being low in quantity, consisted chiefly of lime and alkalies, thus supplying a part of the flux required for smelting the ore. The ash of coal and coke on the other hand, being largely silica, had itself to be fluxed with bases added to the charge. Physically, however, coke proved to have many advantages over charcoal, which could not be used in the furnaces of today. The chief reason, however, for the change from charcoal to coke was the impossibility of maintaining an adequate wood supply.

Jan 1, 1941

By R. H. Brown, F. Keller

Because of the extensive use of Alclad 24s alloy sheet in aircraft construction, there is much interest in the metallurgical changes caused by heat-treatment of this product.1, 2 One of these changes is the result of the diffusion of soluble elements from the core into the coating during treatment. This paper deals with the thermal treatments that may influence diffusion and with the practical effects of diffusion on the serviceability of the product. As is well known, Alclad 24s-T sheet has a core of high-strength alloy combined with surface layers of relatively pure aluminum. The microstructure of a cross section of this product is shown by Fig. I. Not only does the relatively high-purity coating have a high resistance to corrosion, and hence serves as a mechanical barrier between the core metal and the corroding environment, but in addition this coating exerts electrochemical protection over areas where the core may be exposed, such as cut edges. In addition, the coating affords electrochemical protection to projecting heads of A17s-T, 17s-T and 24s-T rivets, or attached members made from these alloys. Under some conditions of heat-treatment, however, diffusion of copper into the coating will alter the electrochemical relationship between the coating and the core to the extent that only partial protection will be obtained under some corrosive conditions. The reason for the electrochemical protection lies in the fact that the coating layers of pure aluminum are anodic to the alloy core. The addition of copper to aluminum produces alloys in which the potential is lower than that of the pure metal. Moreover, as the amount of copper in solid solution in 24s alloy is increased, the potential of the alloy becomes more cathodic. When heat-treated at 920°F. and quenched in cold water, 24s-T is about 0.16 volt cathodic to pure aluminum. However, copper will diffuse from the core into the coating, and if it reaches the surface the potential will be altered in a cathodic direction. Thus the potential difference between the core and coating may be less than 0.16 volt, depending uponIthe thickness of the coating, and the time and temperature of heat-treatment. Of the methods available for determining the extent of diffusion of copper from the core into the coating of Alclad 24s-T, two are generally used; namely, the metallo-graphic and the solution potential methods.3 Metallographic Methods Metallographic methods will reveal the progress of diffusion of copper into the coating. For instance, the diffusion zone in the coating intermediate between the coating surface and the core is shown in Fig. I. This photomicrograph is of a polished and etched cross section of 0.040-in. Alclad 24s-T sheet. Diffusion proceeds into the coating more rapidly along the grain boundaries than through the body of the grains. Consequently, the diffusion zone is not of uniform width

Jan 1, 1944

By F. Keller, R. H. Brown

Because of the extensive use of Alclad 24s alloy sheet in aircraft construction, there is much interest in the metallurgical changes caused by heat-treatment of this product.1, 2 One of these changes is the result of the diffusion of soluble elements from the core into the coating during treatment. This paper deals with the thermal treatments that may influence diffusion and with the practical effects of diffusion on the serviceability of the product. As is well known, Alclad 24s-T sheet has a core of high-strength alloy combined with surface layers of relatively pure aluminum. The microstructure of a cross section of this product is shown by Fig. I. Not only does the relatively high-purity coating have a high resistance to corrosion, and hence serves as a mechanical barrier between the core metal and the corroding environment, but in addition this coating exerts electrochemical protection over areas where the core may be exposed, such as cut edges. In addition, the coating affords electrochemical protection to projecting heads of A17s-T, 17s-T and 24s-T rivets, or attached members made from these alloys. Under some conditions of heat-treatment, however, diffusion of copper into the coating will alter the electrochemical relationship between the coating and the core to the extent that only partial protection will be obtained under some corrosive conditions. The reason for the electrochemical protection lies in the fact that the coating layers of pure aluminum are anodic to the alloy core. The addition of copper to aluminum produces alloys in which the potential is lower than that of the pure metal. Moreover, as the amount of copper in solid solution in 24s alloy is increased, the potential of the alloy becomes more cathodic. When heat-treated at 920°F. and quenched in cold water, 24s-T is about 0.16 volt cathodic to pure aluminum. However, copper will diffuse from the core into the coating, and if it reaches the surface the potential will be altered in a cathodic direction. Thus the potential difference between the core and coating may be less than 0.16 volt, depending uponIthe thickness of the coating, and the time and temperature of heat-treatment. Of the methods available for determining the extent of diffusion of copper from the core into the coating of Alclad 24s-T, two are generally used; namely, the metallo-graphic and the solution potential methods.3 Metallographic Methods Metallographic methods will reveal the progress of diffusion of copper into the coating. For instance, the diffusion zone in the coating intermediate between the coating surface and the core is shown in Fig. I. This photomicrograph is of a polished and etched cross section of 0.040-in. Alclad 24s-T sheet. Diffusion proceeds into the coating more rapidly along the grain boundaries than through the body of the grains. Consequently, the diffusion zone is not of uniform width

Jan 1, 1944

By R. G. Hudson, H. W. Paxton

The activities of iron and chromium in their binary system have been measured by the Knudsen orifice technique. The system is close to ideal at 1200- 1250 C with slight positive deviations. The effect of this on the liquidus and solidus is discussed and these are calculated for two limiting assumptions. The vapor pressure of pure iron, pure chromium, and one alloy is compared with that obtained by the Langmuir free-evaporation technique. The results agree, indicating a vaporization coefficient close to 1. HERE are no reported data on the thermody-A namic activity of iron and chromium in the solid portions of the phase diagram. It is generally assumed'.' that the liquid solutions of iron and chromium obey Raoult's law. Chen and Chipman" have inferred that the liquid solution obeys Raoult's law. The minimum' in the solidus-liquidus curves for the iron-chromium system shows that there are deviations from ideality in either the solid or liquid or both. Because of the importance of developing reliable techniques for obtaining activity data in alloy systems at high temperatures and of the data so obtained, an investigation of the activity of iron and chromium in the binary at 1200-1250 C was undertaken using the Knudsen cell. Experimental The apparatus and experimental procedures used in this investigation were described in a previous paper." The various materials used for the construction of the Knudsen cell are listed in Table I. The metal used for the determination of the vapor pressure of chromium was 99.9 pet pure, obtained from A. D. Mackay, Inc. The iron was obtained as electrolytic grade from Fisher Scientific Company. The Fe-Cr alloys used are shown in Table 11. The largest error and controlling factor in the accuracy in the experiments reported here are introduced because of temperature uncertainty, which is estimated to be ±3 deg C. This introduces an uncertainty of 26 pet in the measured pressure. Experimental Results and Calculations The vapor pressures of pure iron and pure chromium were calculated from the measurements by the Knudsen equation3 on the assumption that only Cr or Fe atoms were present in the gas phase. For metal vapors, at the high temperatures and low pressures involved in these measurements this should be a reasonable assumption. Whitman" corrections for the cells were made. The data and results of pressure calculations are presented in Table I, and are plotted in Fig. 1. In addition the heat of vaporization at the absolute zero, ?E°°, has been calculated for chromium. These calculations are summarized in Table 111. The data used in these calculations are as follows kelley13 (F° - E°°/T ) Speiser, et al H (F° - E°°/T ) 010 where F" — standard free energy at temperature T It was necessary to calculate the total pressure above the alloys from the total weight loss W of the cell during a run, because of the fact that all attempts to collect and analyze the chromium and iron vapor effusing from the cell in the apparatus available failed. The failure resulted from the re-

Jan 1, 1959

By R. Kossowsky

Structural changes in Be-Cu, Be-Ni. Be - Ag, and Be-Fc alloys pressurized in a solid medium were invesligated by resistivity measurements , X-ray diffrac lion in situ and metallogvaphic examination. Some limited tests in liquid medium were also conducted. Good correlation was oblained between diauges of slope of relative resistance us pressure and changes in diffraction pattern. Metallographic examination rez:ealed that the copper, silver, and nickel alloys lwiu heauily due to the applicalion of pressure at room temperature. Using polarized light technique {1012}, {1011}, and possible {1010} twinning planes were identified. At eleuated temperature twinning was moslly confined to the {1012} planes. Although twin-ning could be promoted by application of hydroslutic pvessure (liquid medium), it was strongly enhanced by the pvesence of a nonhydvostatic shear component due to pressurizalion in a solid medium. It was further obserced that a decrease in grain size inlnibiled twinnitzg activily. A great deal of effort has been expended in recent years to render beryllium useful for structural applications. Efforts were concentrated towards a possible phase change and to promoting other than basal deformation modes. Quenching experiments to obtain the high-temperature bcc phase have failed,' nor were alloying additions successful in improving ductility of the brittle hcp phase.2 Herman et a1.3 have reported a new {1011} twinning mode in a Be-4.4 wt pct Cu alloy oriented for a C axis compression sustaining loads to 440,000 psi. A new approach using high-pressure techniques was undertaken at Curtiss-Wright, Wright Aeronautical Division Laboratories. Marder4 reported a 25 pct decrease in relative resistance of commercially pure beryllium at 92 kbar. He proposed that this discontinuity corresponded to the bcc phase found at high temperature; however, X-ray diffraction in silu did not confirm a phase transition.5 contre6 has recently shown that the bcc transition in pure beryllium is lowered to 800°C at 80 kbar accompanied by a 50 pct increase in relative resistance. The purpose of this paper is to report on one phase of an investigation of the effects of high pressures and temperatures in beryllium alloys, namely, twinning behavior in Be-Ni, Be-Cu, Be-Fe, and Be-Ag alloys pressurized to nearly 100 kbar and temperatures up to 200°C. EXPERIMENTAL METHODS Material was obtained from Nuclear Metals, Inc., in the form of a 1.5-mm-diam wire extruded in stainless-steel cladding at 1600° F. Nominal composition of the alloys is listed in Table I, and the major impurities are are given in Table 11. Pressures to 100 kbar* were ob- tained using a National Bureau of Standards type 100/400 ton tetrahedral unit supplied by Barogenics, Inc. This type of apparatus contains a retaining sleeve with a conically tapered internal surface and four pressure-intensifying anvil assemblies with tungsten carbide tips. The 10-mm-long specimen fits into a pyro-

Jan 1, 1968

By E. J. Nielsen, P. R. Strutt

A study has been made of the progressive changes in the distribution of etch-pit structures occurring during high-temperature creep in copper + 7 wt pct Al single crystals oriented with a [113] tensile axis. The two equally stressed glide systems with the highest Schmid factor would be expected to form subboundaries of the type predicted by Kear.2 The alignments of etch-pits on sections parallel to different (111} planes consistent with these types of boundaries were not observed. However, they were consistent with planar subboundaries (on a macroscopic scale). From an analysis of Amelinckx1 it may be shown that stable cross-grid dislocation boundaries may form in the primary slip planes. These boundaries form when dislocations with a Burgers vector not in the slip plane move into the plane by combination of climb and glide. THE geometry of subboundaries formed by the interaction of dislocations of two glide systems has been analyzed by Amelinckx,1 and the particular types produced by deforming fee crystals are predicted by ear.' In this paper types of boundaries which may be formed when climb as well as glide occur are discussed as this is relevant in high-temperature creep. It is assumed in the present investigation that the etch-pits observed in Cu + 7 wt pct A1 on surfaces parallel to {111} planes delineate the sites of dislocations. Although there is no direct evidence for this previous work on a-Cu/Al single crystals by Mitchell, Chevrier, Hockey, and Mon-aghan,3 would show this assumption to be reasonable. The alignments of etch-pits which form during creep are studied on sections parallel to each {111) plane. It is then deduced that these alignments are consistent with a specific type of planar subboundary. The Cu + 7 wt pct A1 single crystals had a [113] tensile axis and Fig. 1(a) shows schematically the relation of the slip planes and slip directions (as represented by tetrahedron ABCD) with reference to the tensile axis. The two equally stressed glide systems with the maximum Schmid factor namely ß-AD and (a-BD, from the analysis of Kear,2 would be expected to form the boundaries shown in Fig. l(a) and (b), also Fig. 5(a) and (b). EXPERIMENTAL PROCEDURE The a-Cu/Al single crystals were grown and annealed in a "gettered" argon atmosphere. Chemical analysis showed the aluminum content to be uniform in each crystal and the difference between crystals was maintained to an accuracy of ± 0.25 wt pct. The initial dislocation density and mean subgrain diameter after annealing was -106 cm-2 and 250 µ, respectively. Surfaces parallel to (111) planes were produced by specially developed electrolytic machining processes. The {111} faces were next electropolished for 5 min in a solution consisting of 25 g chromium trioxide, 113 ml glacial acetic acid and 40 ml water; the applied potential was 8 v. Dislocation etch-pits were revealed using l an etchant described by 1 ml bromine, 45 ml HCl, and - 250 ml water. RESULTS In crystals strained into secondary creep at higher stresses (443 and 750 g - mm-2 at 650° C aligned rows of etch-pits parallel to slip plane traces were evident in sections parallel to the (1111, (ill), and (111) planes, see Fig. 3. As well as the longitudinal alignments in Fig. 3, well formed randomly oriented arrays indicative of an equiaxed subgrain structure are evident. At the lower stresses (100 to 230 g . mm-2) only an equiaxed structure formed during creep. The sections in Fig. 3 are from a crystal crept for 70 hr at 650°C with a CRSS of 443 g.mm-2. Two identically oriented crystals were also deformed at the same temperature and stress for 5 min and 4 hr. In the crystal crept for 5 min, the etch-pits were randomly distributed with no tendency for directional alignment, see Fig. 2(a). As shown in Fig. 2(b) aligned arrays were evident after 4 hr creep but they were not nearly so well defined as in Fig. 3. The alignments (parallel to the arrows) in Fig. 3 are consistent with the existence of boundaries in the two main slip planes a and ß. The way in which this is deduced is seen by reference to Fig. l(c), where the existence of boundaries in the a and ß planes is verified by sectioning parallel to a,ß, and d. The (111) and ß(111) planes intersect the d(111) plane along BC [101 ] and AT [011] and alignments parallel to [101] and [011] are clearly evident in Fig. 3(c) in a section parallel to the d(111) plane. Similarly the a, and ß planes in Fig. l(a) intersect each other along DC [110] and hence there will be an alignment parallel to [110 ] in sections parallel to the a-plane and the ß-plane; this is evident in Fig. 3(a) and Fig. 3(b). It is interesting to note that alignments of etch-pits consistent with the boundaries predicted by Kear2 were not observed; see Figs. l(a) and l(b). The geometry of boundaries in {111} planes as shown in Fig. l(c) is discussed later. In Fig. 4(a) the individual etch-pits are resolved and the alignments are exactly parallel to the slip trace direction [101]. However, in some areas alignments deviate away from the slip trace direction by as much as 10 to 15 deg, this is evident in Fig. 4(b), and in Fig.

Jan 1, 1969

By E. V. Crane

A TREMENDOUS volume of the metal rolled annually into sheets, strips and coil stock finds its way to a host of stamping and manufacturing plants which are the quantity production units of the country. Considerable in volume, too, are the rolled and extruded rods which go into forging and manufacturing plants for conversion into the same general line: those widely sold metallic necessities and luxuries of the household, the office, transportation, farming and building construction. Yet, in spite of its age and its importance, the stamping trade has been doing its "engineering" largely by trial and error. Its distinctive method is shearing out and plastically working metal to finished shape in a few quick strokes with high loads and expensive tools which are warranted only by large quantities to be produced. The principal operations have many features in common with rolling and wire-drawing methods. Combinations of stresses are different, however, and details of operations are infinite in variety. An engineering study of the subject begins with stress analysis, but must go back to metallurgy for its foundation. A grouping of pressed-metal working operations according to whether the metal is (1) sheared, (2) bent, (3) drawn or (4) squeezed has proved useful. All of these groups include instances of both hot and cold operations. For discussions of metal working properties, the division between hot and cold working is taken as the recrystallization range of temperature. This, of course, brings tin, lead and often zinc into the hot-work range at or near room temperature. The outstanding hot-working press field is in forging: particularly of brass; all of which is included in the squeezing group.

Jan 1, 1931

By J. N. Ong, J. P. Ratledge, J. H. Boyce

SINCE German operators opened the Tsumeb mine in the early 1900's, continuous operation has been interrupted only by enforced shutdowns during two world wars and the depression of the 1930's. Original metallurgical practice was blast furnace smelting. This was applicable only to low zinc ore, leaving large tonnages of high zinc ore to be stockpiled on the surface. A gravity concentrator using tables, buddles, and jigs operated for several years, but differential flotation of the ore did not get beyond the experimental stage. When the property was put up for sale by the South African Custodian of Enemy Property there was an estimated 434,000 tons of ore on surface dumps. The dump material, assaying 4.48 pct Cu, 15.8 pct Pb, and 10.9 pct Zn, had become highly oxidized during a stay of many years on the surface. But these dump ores had to be used in evaluating possible metallurgy because the shaft became flooded after the 1940 shutdown and underground ore was unavailable. Many companies examined Tsumeb but quickly lost enthusiasm because of the formidable metallurgical problems presented by the dump ore. However, on the basis of extensive test work, the present company decided that differential flotation would be successful and purchased the property after competitive bidding. Geology and Mineral Association is Complex The Tsumeb mine lies near the northern boundary of South West Africa at an altitude of 4200 ft. The village of Tsumeb is 335 air miles northeast of Wal-vis Bay, territorial port of entry. The orebody is a hydrothermal replacement deposit associated with an irregular intrusion of aplite cutting folded pre-Cambrian dolomite beds. In plan the deposit is a lens of 250x600 ft maximum dimensions. In section the orebody dips 55" south from the surface to 2000 ft, below which there is a reversal in dip to 75" north. Mineralization is localized in the aplite and in the adjoining brecciated dolomite. In the upper levels the ore is largely confined to a single lens, but below the 1890 level massive sulphide ore forms north and south lenses that partially enclose a pipelike body of medium to low grade disseminated ore, part of which is of too poor a grade to mine. Drilling below the 24th, or bottom level, has disclosed that a high percentage of the mineralization from the 3000 to 3300-ft horizons is comprised of copper and lead oxides. The deep oxidation may be local, since it appears due to circulating waters in a major fault cutting the orebody. Tsumeb ranks as one of the highest grade base metal deposits in the world. It is geologically and mineralogically famous for 41 copper, lead, zinc, vanadium, and germanium ore minerals, but its complex mineral assemblage is not attractive to metallurgists. In addition, there is a gradual change in oxidation intensity from the upper levels to the lowest level now operating, which is the 24th. This is well illustrated by the copper minerals. In the upper levels malachite and azurite are predominant, in the intermediate levels chalcocite, and in the lower levels tennantite. Throughout the mine there are sufficient heavy metal soluble salts to activate zinc, and large amounts of depressants are required even for so-called clean sulphide ores. When the same sulphide ore is exposed to prolonged oxidation aboveground, as was the case with the dump ores, reagent requirements become fantastic. Plant Construction First staff members arrived at Tsumeb in March 1947, and by May essential services had been restored and mine unwatering began. In 2 1/2 months company employees built a temporary jig and sorting plant for treating existing dumps to provide a saleable product during high metal prices. Meanwhile, concentrator design and construction was contracted to a South African firm, with subcon-

Jan 1, 1956

By L. E. Shiffman

W. J. Parton—Those operators faced with the problem of treating fine coal whether in bituminous or anthracite will find this paper most timely. I would like to take this opportunity of discussing Mr. Schiffman's paper and at the same time express certain views relating to our Tamaqua plant. I would like to ask the author what type of impeller and diffuser is used in the Denver cells? Screen analysis of products from individual cells indicate that coarser material resists flotation and only floats after greater retention time in the last few cells. Also, the need for a scavenger screen to reclaim non-floated coal particles further stresses this point. I have always felt that more efficient means of cleaning coal between 10-mesh and 28-mesh existed than flotation. Reagent and power costs are high for the flotation process. When floating +28-mesh particles, cell capacity is lowered and some of the particles are lost with the refuse. The Tamaqua plant of the Lehigh Navigation Coal Co. floats —28-mesh coal and capacity of recoverable coal is 40 tph for 1800 cu ft of Denver cells; or 0.05 tons per cu ft of cell. At Kimberly 7.75 tph for 600 cu ft of cell gives 0.013 ton per cu ft of cell. At Bessie 14 tph for 800 cu ft of cell gives 0.017 tons per cu ft of cell. It would be appreciated if the author would comment on what he feels is the upper size limit of particle to attain most efficient utilization of the flotation process. The dewatering screw is a very interesting development since it offers a simple way to prepare coal sludge for more complete clewatering by drainage or mechanical dewatering on screen or filters. In other words it could be used to accomplish the same thing as a thickener tank. I would appreciate having the author's comment on how he thinks such a screw dewaterer would work on a froth.* The process as used in floating coal at the Bessie and Kimberly plants may be referred to as more of a bulk oil float in contrast to a froth flotation process. Experiments on increasing capacity of cells is most interesting since we are going through such an experi- mental period at the present time. Recently a double overflow was installed on our No. 30 Denver cells. So far results are not conclusive. In reviewing this paper the following comments are made pertaining to investigation of methods for increasing capacity: Supercharging: Supercharged air in matte flotation or for that matter the use of the normal amount of air drawn in by the impeller would in all probability cause such an aeration in the cell as to destroy the buoyant effect given to the coal particles by the excessive amount of kerosine used. In other words, air creates an agitation zone throughout the cell, creating a boiling and thereby giving a lower recovery in the cell. It would be interesting to know whether the 7 pct increase in recovery was with no air being admitted to the stand pipe. Changing Impeller Speed: The speed of a receded disc impeller for a No. 30 cell as recommended by the Denver Equipment Co. is, I believe, approximately 250 rpm. At this speed and using supercharged air in excess of 8-oz pressure, we have observed a boiling action in the cells. In our flotation we endeavor to obtain some degree of froth flotation using pine oil as a frother. The boiling action as caused by increasing the amount of air added to the cells is detrimental to recovery in froth flotation. It is our belief that to obtain increased recovery from a cell in froth flotation, additional air must be introduced but at the same time this air must be dispersed throughout the pulp in the form of small bubbles and this can only be done by increasing the speed of the impeller. Therefore, if Mr. Schiffman decreased the speed of the No. 30 impellers and at the same time continued to use supercharged air, the boiling action may have been increased because larger bubbles developed. The lower recovery as reported could be due to this factor. Decreasing the impeller speed will definitely decrease the power consumed but may have other disadvantages. First, we believe it will permit "sanding" in the cell and this in our opinion will increase the wear on the impeller and diffuser, especially so, if there is pyrite and/or sand present in the feed. "Sanding" in the cell when air is used, as in froth flotation, will effect the dispersion of this air and cause boiling.

Jan 1, 1951

By L. E. Shiffman

W. J. Parton—Those operators faced with the problem of treating fine coal whether in bituminous or anthracite will find this paper most timely. I would like to take this opportunity of discussing Mr. Schiffman's paper and at the same time express certain views relating to our Tamaqua plant. I would like to ask the author what type of impeller and diffuser is used in the Denver cells? Screen analysis of products from individual cells indicate that coarser material resists flotation and only floats after greater retention time in the last few cells. Also, the need for a scavenger screen to reclaim non-floated coal particles further stresses this point. I have always felt that more efficient means of cleaning coal between 10-mesh and 28-mesh existed than flotation. Reagent and power costs are high for the flotation process. When floating +28-mesh particles, cell capacity is lowered and some of the particles are lost with the refuse. The Tamaqua plant of the Lehigh Navigation Coal Co. floats —28-mesh coal and capacity of recoverable coal is 40 tph for 1800 cu ft of Denver cells; or 0.05 tons per cu ft of cell. At Kimberly 7.75 tph for 600 cu ft of cell gives 0.013 ton per cu ft of cell. At Bessie 14 tph for 800 cu ft of cell gives 0.017 tons per cu ft of cell. It would be appreciated if the author would comment on what he feels is the upper size limit of particle to attain most efficient utilization of the flotation process. The dewatering screw is a very interesting development since it offers a simple way to prepare coal sludge for more complete clewatering by drainage or mechanical dewatering on screen or filters. In other words it could be used to accomplish the same thing as a thickener tank. I would appreciate having the author's comment on how he thinks such a screw dewaterer would work on a froth.* The process as used in floating coal at the Bessie and Kimberly plants may be referred to as more of a bulk oil float in contrast to a froth flotation process. Experiments on increasing capacity of cells is most interesting since we are going through such an experi- mental period at the present time. Recently a double overflow was installed on our No. 30 Denver cells. So far results are not conclusive. In reviewing this paper the following comments are made pertaining to investigation of methods for increasing capacity: Supercharging: Supercharged air in matte flotation or for that matter the use of the normal amount of air drawn in by the impeller would in all probability cause such an aeration in the cell as to destroy the buoyant effect given to the coal particles by the excessive amount of kerosine used. In other words, air creates an agitation zone throughout the cell, creating a boiling and thereby giving a lower recovery in the cell. It would be interesting to know whether the 7 pct increase in recovery was with no air being admitted to the stand pipe. Changing Impeller Speed: The speed of a receded disc impeller for a No. 30 cell as recommended by the Denver Equipment Co. is, I believe, approximately 250 rpm. At this speed and using supercharged air in excess of 8-oz pressure, we have observed a boiling action in the cells. In our flotation we endeavor to obtain some degree of froth flotation using pine oil as a frother. The boiling action as caused by increasing the amount of air added to the cells is detrimental to recovery in froth flotation. It is our belief that to obtain increased recovery from a cell in froth flotation, additional air must be introduced but at the same time this air must be dispersed throughout the pulp in the form of small bubbles and this can only be done by increasing the speed of the impeller. Therefore, if Mr. Schiffman decreased the speed of the No. 30 impellers and at the same time continued to use supercharged air, the boiling action may have been increased because larger bubbles developed. The lower recovery as reported could be due to this factor. Decreasing the impeller speed will definitely decrease the power consumed but may have other disadvantages. First, we believe it will permit "sanding" in the cell and this in our opinion will increase the wear on the impeller and diffuser, especially so, if there is pyrite and/or sand present in the feed. "Sanding" in the cell when air is used, as in froth flotation, will effect the dispersion of this air and cause boiling.

Jan 1, 1951

By C. G. Dunn

NUCLEI that are formed during the recrystallization of a grain following plastic deformation generally have orientations that differ from the original. This aspect of recrystallization may be described in terms of orientation changes. It was shown previously, in an investigation on recrystallization in silicon ferrite,1 that the observed orientation changes were highly improbable on a chance basis, and that some mechanism must be involved. Analysis showed that the data could be satisfactorily classified into the smaller of two subclassesf of the 36 third- order twin transformations. No attempt was made at that time to classify the data within the special class of 12 third-order twin transformations, although results did indicate a greater probability for some of them to occur. A classification of this type would be more valuable, of course, with more data on orientation changes per old deformed grain. The present work fulfills this condition to some degree and also extends the scope of the investigation to include the effects of original orientation and the amount of plastic deformation. The effect of original orientation is of considerable interest because of the known effects of orientation on plastic deformation, particularly with regard to degree of fragmentation and the formation of de- formation bands, and because the orientations produced by deformation should influence the orientations obtained through recrystallization. Barrett and Levenson2 reported that single crystals of iron deformed in the range 82 to 97 per cent could be put into three general classes; namely, crystals in class I maintained a reasonably sharp single orientation, those in class 2 transformed into two distinct orientations, and those in class 3 changed into a large number of major and minor orientations. Something similar would be expected for silicon ferrite crystals, and verification of this for a few cases of types class I and class 2 deformation has been reported elsewhere3 for single crystals of silicon ferrite cold-rolled in the range 10 to 20 per cent. As an example of class 2 deformation, it was shown that a crystal of silicon ferrite cold-rolled in a {110} plane in a < 100> direction developed two layers, or deformation bands differing in orientation. When this happens it is possible to etch away one band and leave a single structure for use in studying the orientation changes that occur during recrystallization. when preferred crystal orientations are obtained in recrystallization, it is notparticularly necessary to evaluate groups of common orientation, as was done previously (ref. I, Table 6); but an

Jan 1, 1946

By J. B. Wagner, p. Hembree

The iron tracer diffusion coefficient of umstite has been measured at 110(fC across the phase field and at a single composition at 800°C. Assuming a simple cation vacancy model the tracer diffusion coefficient was found to be a linear function of the cation vacancy concentration at 1100°C. The equation is D = 3 x 20 29 where denotes the concentration of vacancies in numbers per cc. The tracer work at 800°C was carried out to investigate the reported "pinning" of tracer to the wustite surface at low temperatures. No evidence for the "pinning" of the tracer was found at 800°C in COz-CO gas mixtures. HIMMEL, Mehl, and Birchenall,&apos; Carter and Richardson,2 and Desmarescaux and La combe3 have measured the diffusion of iron tracer in wustite at several temperatures and compositions. The present work was undertaken to extend the measurements over a large composition range at 1100°C and to resolve certain apparent discrepancies in the data, expecially at lower temperatures. EXPERIMENTAL Wustite was prepared by oxidizing rectangular iron plates* in C02-CO mixtures. The samples were •The iron was supplied by the Battelle Memorial Institute courtesy of the American Iron and Steel Institute. The analysis is presented in Table I. quenched. Due to the inward flow of cation vacancies during oxidation, the center of the sample contained a thin void. The edges of the wustite slab were sanded until the sample could be split into two parts. Each part was then sanded on the front and back flat area until a smooth surface was obtained. The specimens were then replaced in the furnace and equilibrated at llOO°C in a predetermined COa-CO mixture by methods described elsewhere.4"6 The specimens were again quenched and the surfaces were lightly sanded to remove any roughness following the first equilibration. The specimens were then reequi lib rated in the same C02-CO mixture for thirty minutes in order to relieve any mechanical damage on the surface due to the polishing. The specimens were then quenched and the tracer was applied by an electroplating technique. The work of Carter and ~ichardson&apos; demonstrated that there was no systematic difference in the iron tracer diffusion coefficient in wustite if the tracer was plated, dried, or evaporated on the specimen. In the present study a piece of filter paper was saturated with an iron chloride solution of pH <* 3 that contained the tracer FeS5. The wustite was placed on the filter paper and made the cathode. A current density of 0.4 to 0.6 ma per sq cm was passed for about five to ten minutes. The thickness of the tracer layer was estimated to be about 7 x lom6 cm. This estimate was made by considering the area plated, the current flow, and time for plating and the activity of the iron in the plating solution. Different areas of the specimen were counted using a collimator to determine the uniformity of the tracer. Any specimen which exhibited a variation from the initial count rate (about 1500 cpm) by more than 15 pct was rejected. An estimate of the time necessary to convert the thin layer of iron tracer to wustite was made using the data of Pettit and wagner." he estimated time was 1 sec at 1100°C assuming linear oxidation kinetics. The shortest diffusion anneals were 1800 sec. The samples were suspended in the hot zone of a furnace by two platinum wires. Two separate specimens were run at the same time. Only the edges of each sample were in contact with the wires. The C02-CO gas of the same composition as that used in the pre-diffusion anneals flowed freely around the samples at a linear velocity of 0.9 cm per sec. To initiate a run, the specimens were lowered from the cold zone of a furnace to the hot zone by a magnetic lowering device." bout 60 sec were required for lowering. To terminate a run, the sample was withdrawn from the hot zone to the cold zone. Time zero for the beginning of the experiment was taken when the sample blended into the red glow of the furnace and conversely for the end of the experiment. The surface decrease method of measuring the tracer diffusion coefficient was used to collect the data. This method requires that counting geometry be reproducible because the specimen is counted before the diffusion anneal and after the anneal. A special jig was constructed for each specimen so the specimen could be removed from the jig and returned to the jig such that the well geometry was reproducible.

Jan 1, 1970

By E. L. Spain

The deposits described in this paper occur over much of Wayne County and in the southeast portion of Hardin County, Tennessee, and in the northeast and northwest portions of Mississippi and Alabama respectively. The presence of tripoli in this region has been known for some time and descriptions of various occurrences in Tennessee have been made by Jewelll and Miser2, while Hilgard3, Lowe4 and Logan5 have treated the deposits that occur in the adjacent portions of Alabama and Mississippi, but there has not been a &apos;general survey of the entire field summarizing completely the geology of the deposits with respect to their origin and stratigraphic relationships. During 1934, while engaged in surveys of mineral resources through this region for the Tennessee Valley Authority, the writer collected data with this in mind, and has assembled them in this report. He is indebted to H. S. Rankin and N. A. Rose, of the Tennessee Valley Authority Geology Division, for field assistance. Location of Tripoli Deposits Fig. 1 shows the locations of deposits of tripoli in a long belt that extends from northeast Wayne County southwestward into northwest Alabama and thence passes into Mississippi, where the formations carrying it are finally covered by Cretaceous sand and gravel of the Mississippian Embayment. Occasional deposits occur also in the southeastern corner of Hardin County, Tennessee. While tripoli is found at nearly all points along this axis where the related formations are exposed, the largest deposits are grouped about three different centers. Waynesboro-Collinwood District.—In the area between Waynesboro and Collinwood, in Wayne County, Tennessee, tripoli of various grades outcrops in the valley of Green River and in tributary valleys on either side. This district is roughly 12 miles long in a northeast-southwest direction and has a maximum width of 5 miles at its northern end. Exposures are found in road cuts, highway chert pits, in the beds of some of the streams, and on hillsides. The greatest number of high-grade

Jan 1, 1938

By E. L. Spain

The deposits described in this paper occur over much of Wayne County and in the southeast portion of Hardin County, Tennessee, and in the northeast and northwest portions of Mississippi and Alabama respectively. The presence of tripoli in this region has been known for some time and descriptions of various occurrences in Tennessee have been made by Jewelll and Miser2, while Hilgard3, Lowe4 and Logan5 have treated the deposits that occur in the adjacent portions of Alabama and Mississippi, but there has not been a &apos;general survey of the entire field summarizing completely the geology of the deposits with respect to their origin and stratigraphic relationships. During 1934, while engaged in surveys of mineral resources through this region for the Tennessee Valley Authority, the writer collected data with this in mind, and has assembled them in this report. He is indebted to H. S. Rankin and N. A. Rose, of the Tennessee Valley Authority Geology Division, for field assistance. Location of Tripoli Deposits Fig. 1 shows the locations of deposits of tripoli in a long belt that extends from northeast Wayne County southwestward into northwest Alabama and thence passes into Mississippi, where the formations carrying it are finally covered by Cretaceous sand and gravel of the Mississippian Embayment. Occasional deposits occur also in the southeastern corner of Hardin County, Tennessee. While tripoli is found at nearly all points along this axis where the related formations are exposed, the largest deposits are grouped about three different centers. Waynesboro-Collinwood District.—In the area between Waynesboro and Collinwood, in Wayne County, Tennessee, tripoli of various grades outcrops in the valley of Green River and in tributary valleys on either side. This district is roughly 12 miles long in a northeast-southwest direction and has a maximum width of 5 miles at its northern end. Exposures are found in road cuts, highway chert pits, in the beds of some of the streams, and on hillsides. The greatest number of high-grade

Jan 1, 1938

Alexander N. Winchell, Butte, Mont. (communication to the Secretary): Mr. Spurr calls attention to the fact that an ore-deposit may be due to a succession of concentrations at different geological epochs. He cites an example of such a condition on Napoleon creek, a branch of Forty-Mile creek, Alaska. It will perhaps be of interest to call attention to another example of the same general character, not so remotely situated. The example referred to is located on Pole creek, a tributary of Cherry creek, in the extreme northeastern part of Madison county, Montana. An excellent geological map of this region is to be found in the Three Forks folio (No. 24) of the United States Geological Survey. According to this map, Pole creek, in its upper course, occupies the contact between the " Flathead " formation, which Peale correlates with the Middle and Lower Cambrian, and an area of gneisses and schists supposed

Jan 1, 1903