Search Documents

By Charles E. Barker

Jan 1, 1985

By C. R. Knopp

Gas-oil relative permeability ratio is an important relationship in oil reservoir predictive calculations. A correlation has been developed from 107 gas-flood k/k tests on Venezuelan core samples. The correlating parameter is based on restored-state water saturation tests and' is applicable to both consolidated and poorly consolidated sandstone reservoirs. Data of the correlation show that there are no distinguishah1e differences between the mass-data groupings for the two c1assifications A procedure is recommended for running .sufficient relative. permeability analyses to compute a geometric mean of the sample group. The geometric mean is more representative of the total core, and probably the entire reservoir. For example, while only one in four of the k,,/k,., test curves agreed closely with the resultant correlation of this report, the geometric mean curves of the 16 suites (three samples or more). showed good agreetment ill three cases out of four. INTRODUCTION The gas-oil relative permeability ratio is an important, fundamental relationship in most oil reservoir predictive calculations. Predictive calculations are made to estimate future reservoir production characteristics and ultimate oil recovery. The k1,/k2, relationship is specifically needed to relate the surface gas-oil ratio to the reservoir oil and gas saturation, and to calculate the relative movement of these phases within the reservoir whenever some of the more complex driving mechanisms are present. Laboratory k1/k2, tests are not generally run as a routine analysis. Consequently, k1/k2 data often are not available when needed because the cost of laboratory work could not be justified or the need for such data had not been properly anticipated. When laboratory k1/k2, data are available, they are often very difficult to interpret. For example, wide divergence is sometimes shown in a family of k1,/k1, tests representative of the producing horizon in a single well. With these considerations in mind, a study was made to determine if a relationship might exist between the k1,/k2, curve and some other simple laboratory test criteria. The most probable k1/k2, curve correlation for Venezuela described in this paper is the result of the investigation. The presented correlation defines the most probable gas-flood k,,/k,, curve through the medium of air-water capillary displacement and centrifuge water saturation tests. The laboratory procedures of these tests are. relatively simple, and inexpensive; test data should be. widely available- from routine analysis. DATA AVAILABLE, LABORATORY METHODS The report correlation utilized 107 gas-Hood k1/k2, tests run on sandstone cores of Venezuelan reservoirs. Table 1 is a general tabulation of data pertinent to the tests, while Table 2 summarizes the data. Thetests include 96 from Western Venezuela and 11 from Eastern Venezuela. Eighty-two- of the 107 test samples were sandstones that varied from poorly consolidated to-unconsolidated; 25 were consolidated. The average sample porosity was 26.7 per cent and the average permeability was 1,121 md; these values typify the better sandstone reservoirs of' Venezuela. The Welge gas-flood technique,' based on fundamental Buckley-Leverett frontal displacement theory, was introduced in about 1952 and is widely accepted in the industry. The laboratory procedure is relatively simple, rapid, and can be performed on small core samples. While there have been some minor variations in sample preparation and laboratory procedure in the tests used for the correlation, these tests can be generally summarized as follows. The core sample was first sol vent-extracted and dried. Connate-water saturation was restored by the oil-flushing or evaporation-blow down methods. At the beginning of gas flood the hydrocarbon pore volume was completeiy saturated with the test oil phase. Unsteady-state gas-oil displacement then began with the injection of nitrogen or helium. while the displaced oil and gas phases were incrementally metered at the out-flow face. From the test data, the k,,/k,, curve was calculated by the Welge method.' The individual oil and gas relative permeabilities were also calculated." CORRELATING PROCEDURES In attempting to establish a basis of correlation, we found that broad mid-range sections of 105 of the 107 k,,/k,, test curves could be closely duplicated by a straight line. Only two curves did not show a degree of linearity in this region. Correlation-curve definition parameters were subsequently developed from this observation of consistent mid-range linearity. Possible correlating variables were limited to the physical properties measured on core samples that (1) were widely available as common test data and (2) could be easily and cheaply obtained through future laboratory work. The more obvious possibilities were porosity, permeability and

Jan 1, 1966

By R. D. Rubright, Owen J. Hart

In the Bingham district over a span of more than 90 years, 43,947,104 tons of "non-porphyry" copper, lead, zinc, gold, and silver ore have been mined from a folded and faulted alternating series of Pennsylvanian and Permian limestones and sandstones and from some Tertiary intrusives. This ore came from six major mine areas located east, south, and west of the Bingham stock, site of Kennecott's porphyry copper deposit. The sediments were affected by varying degrees and types of metamorphism within 2000 feet or more of the Bingham stock. The intrusives consisting of the mineralized Bingham and the unmineralized Last Chance stocks and numerous dikes and sills of granite and monzonite were intruded into the asymmetrical northwest-trending and plunging Bingham syncline. Extrusives, although present, contain no ore. The bulk of the non-porphyry ore in the district was found above the Midas thrust. The primary ores are found in three major types of deposits: concordant bedding fissures, crosscutting fissures, and replacement deposits. These deposits consist of both copper and lead-zinc ore bodies that contain various amounts of gold and silver. These are in places roughly zoned both laterally and vertically and have been mined for up to 10,000 feet outward from the center of the Bingham stock and up to 5000 feet vertically below the surface. Secondary ore was of minor importance and was found in and under the oxidized zone at shallow depths. Genetically the Bingham stock, the ores, and related phenomena have had a common source.

Jan 1, 1968

By CARLE R. HAYWARDC

BEFORE discussing this subject it is necessary to define somewhat the meaning of the tern metallurgical.. When I was a student at M. I. T. ore-dressing was not thought of as metallurgy in any sense of the word, but it was considered as more closely allied to mining, enabling the miner to market an otherwise unmarketable product, or at least to market it to better advantage. Progress in ore-dressing has gradually allied it more closely with smelting, for at present the raw material received by the smelter is predominantly concentrates and smelting practice has been profoundly affected by the products of the concentrating mill. It is not surprising therefore that in many schools ore-dressing is frankly considered as metallurgy and although there may be some dissenting opinions it will be considered as such in this discussion. Twenty-five years ago at M. I. T. metallography was taught in a few optional lectures. This subject has developed rapidly and been expanded into the new and increasingly important field of physical metallurgy. To many metallurgists the -term metallurgy means only physical metallurgy. They know little or nothing about smelting and leaching and even less about ore-dressing. Having then broadened the scope of the term metal¬lurgy to cover ore-dressing, smelting, leaching and phys-

Jan 1, 1930

By Richard E. Chism

If internal commotion can be called life, the Mexicans have certainly lived more in the last seventy-five years than any other people. To the oppression of the Spanish viceroys succeeded the sanguinary tumults of the Revolution of Independence, after which the Supreme Congress bequeathed its heritage of uncertain power to the empire of Iturbide, the only one ever established by Americans upon American soil, with an American at its head. That shortlived reign mas followed by years of ceaseless, bloody, and, to the superficial observer, meaningless revolutions—the deeper political and ecclesiastical significance of which it is beyond the scope of this paper to discuss. Then came foreign intervention, the ill-fated Austrian's brief supremacy, and the final triumph of the patriot cause under rugged old Benito Juarez, who crowned the victory of arms by a series of reforms breaking forever the temporal power of the Church and ushering in the calmer era which has lasted from the first accession of Diaz to the present day. During all those troublous times, the revolutionary ocean, that rolled so deeply over all other relics of Spanish dominion, had left almost unaltered the ancient laws of Spain, still lifting themselves above the tide, like landmarks of a flooded world. Many of these laws were obsolete ; some were absurdly inadequate to the demands

Jan 1, 1886

By J. A. Herbst, K. Rajamani

INTRODUCTION Recent research has shown that popu- lation balance models hold considerabl e promise as a basis for accurate mill scale-up from laboratory batch grinding tests. It has been shown that entire product size distributions from large ball mills can be predicted from data obtained in tests in small mills with errors of less than one or two percent. This level of accuracy has been demonstrated for batch grinding scale-up (Herbst and Fuerstenau, 1980; Austin, 1973; and Malghan and Fuerstenau, 1976) and for continuous grinding scale-up (Herbst, et a1., 1976; Herbst, Rajamani and Sanchez, 1982; and Herbst, Rajamani and Lo, 1982) in commercial mills up to 14.5 x 32 feet. A procedure which has been proposed for commercial mill design using the population balance approach and specific power information is shown in Figure 1 (Herbst and Fuerstenau, 1980). Here batch grinding data (size distributions for various energy inputs) obtained in a small batch mill is input to an estimation program which determines the "best" set of breakage rate parameters from the data provided. In turn, these breakage rate parameters are input to a scale-up program along with traditional inputs such as: a) desired circuit throughput and product size b) circuit operating conditions including fraction of critical speed and fractional ball load, size distribution and % solids in feed and circulating load (if closed circuit). In addition, since the population balance approach relies on more detailed models of the grinding circuit sub- processes than the classical design methods do, it is necessary to provide input to the scale-up program on the nature of material transport through the mill (e.g. residence time distribution information) and classifier performance characteristics (e .g. selectivity functions). The scale-up program will make the design calculations including the selection of mill dimensions and drive requirements, will predict product size distributions throughout the commercial circuit and will provide information on the sensitivity of the design to errors in the design assumptions. In order to implement such a scale- up scheme it is necessary to have a computer program for parameter estimation and a program for scale-up prediction. A program which is suitable for parameter estimation, ESTIMILL, has been developed and tested on a wide variety of ores at the University of Utah. This program has been in use in

Jan 1, 1982

By Shun-ichi Satoh

The electric arc welding of cast iron has been studied by Braune Lamberton, Schimpke, Kenyon, Gale Manufacturing Co., Wedemeyer Candy, Neese, Miller, Carter, American Welding Society, Namack Lebrun, Achenbach, Jansson, Xochendorffer and others.' The write of this paper has been able to obtain a series of cast irons, from gray tc white, without using cast-iron electrodes but by coating on wrought-iron bars mixtures of carborundum (Sic) and graphite (C). In this work, he found the curious phenomenon of barium carbonate.

Jan 1, 1929

By AIME AIME

THOUGH the Annual Meeting of the Institute-officially numbered 158 on the records was delayed a bit at the start by low steam pressure on the locomotives bringing members to New York, the crowd that finally arrived more than lived up to expectations, and the technical program had few difficulties because of absent authors or lack of competent discussers. The transportation difficulties were occasioned by the fact that Monday, Feb. 15, was the third coldest day in the 72 year history of the New York Weather Bureau, the official temperature being 8 below zero. The New York Central's premier train, the 20th Century, due at 9:30 a.m., arrived about 6:30 p.m., and the Commodore, another crack train from Chicago, was about equally late.

Jan 1, 1943

By B. H. Caudle, L. G. Davies, I. H. Silberberg

This paper presents a method of predicting the recovery and performance of a five-spot steam injection project, in which a realistic approach to pattern sweepout efficiencies is made. Published methods for radial systems were modified for the five-spot pattern by approximating the stream lines with straight lines radiating from the injection well and then converging to the producing well. In each radial segment, the position of the steam front and the temperature profile ahead of the steam front were determined by heat balance equations, which included an estimation of heat losses to surrounding formations. The location of the saturations behind the cold water front was determined from a Buckley-Leverett solution to the material balance equation. Results from this program show steamflood recovery in a five-spot pattern to be considerably less than that predicted for true linear or radial flow systems. For a specific reservoir containing 900-cp oil, a steamflood in a purely radial flow system was predicted to recover more than 75 percent of the original oil in place when 2 PV of water had been injected as steam. A five-spot steamflood with otherwise identical properties was predicted to recover 10 percent of the original oil in place when 0.15 PV of water had been injected as steam and to recover almost no oil thereafter. A cold water five-spot flood in this system was predicted to recover approximately W percent of the oil in place with I PV of water injected. For a five-spot pattern in an example reservoir with 10-cp oil, steam injection similarly showed lower ultimate recovery than water injection but no improvement in recovery rule. Introduction The thermal recovery method considered in this study is steam injection in a five-spot pattern. Pattern steam injection has been given little attention in the past, possibly because of some rather obvious disadvantages. Unless steam temperature is maintained throughout the entire swept area, the process will revert to simple waterflood with all heat being lost prior to reaching the oil bank. Also, the oil viscosity reduction takes place near the steam front and not around the producing wellbore, so that low producing rates must still be endured. This is the reason for the success of the steam stimulation, or cyclic injection, in which the fluids are produced from the same well used for injection. On the other hand, steamflooding can offer some advantages. Oil displacement is by four methods: (1) mechanical displacement by the condensed water, (2) viscosity reduction of the crude oil, (3) swelling of the crude oil, and (4) distillation of the crude oil in the steam zone. Although dependent upon the crude, laboratory experiments have shown displacements up to 80 percent by steamflooding. In addition, steam is a good heat transport medium, since it is cheap and has a high heat content. Previous Investigations Previous publications have reported methods for predicting recovery in a steamflood for linear and radial systems. Since no pattern sweep efficiency is taken into consideration, the recovery even from a radial system must be greater than from more realistic geometries such as the very common five-spot patterns. Probably the broadest coverage is given by Willman who reported experimental results and offered a method of predicting recovery for a radial flow system. They concluded that both hot water and steam injection recover more oil than an ordinary waterflood, and that steam injection could yield recoveries "as much as 100 percent greater than by water flood." They also concluded that both the heat requirements for a reservoir and the residual oil remaining in the reservoir after steam injection were independent of the amount of oil originally in place, that short exploitation times were desirable, and that a high percentage of net sand in the reservoir with a high initial oil saturation was desirable. The method assumes that the flood occurs in three concentric cylindrical zones: (1) an inner steam zone, (2) a central hot water zone, and (3) an outer cold waterflood zone. Displacement in the steam zone is based on laboratory-determined residual oil saturations while the hot water and cold water zones use the conventional Buckley-Leverett equations. Although the results shown by Willman et al. are for a radial system flowing out from the well to an assumed external circular boundary, their equations did

Jan 1, 1969

By AIME AIME

THE convention which met in Washington at the call of the Joint Conference Committee was called to order at ten o'clock on Thursday morning; June 3, by Richard L. Humphrey, temporary chairman, member of the American Society of Civil Engineers, who made a brief statement of the reason for the meeting. Lieut. Col. Charles W. Kutz, Corps of Engineers, U. S. A., and Engineer Commissioner of the District of Columbia, then welcomed .the engineers composing the convention on behalf of the District of Columbia and, the Washington engineers. Although an elaborate program had been prepared on which were many well-known speakers on interesting and important topics, , it was voted to intersperse this to fill in the usual and unavoidable hiatuses in the business program of such a convention[ Calvert Townley, president of the American Institute of Electrical Engineers, was elected permanent chairman, and J. C. Hoyt, of Washington, was elected secretary of the convention. The following committees were appointed: Consti¬tution and by-laws, Richard L. Humphrey, chairman; resolutions, Philip N. Moore, chairman; and program, F. H. Newell, chairman. Then, Gardner S. Williams, member of the, A. S. C. E. and the Grand Rapids Engineering Society of. Grand Rapids, Mich., and one-time member of the American Association of Engineers, offered the following resolutions:

Jan 1, 1920

By M. E. Grimes

A method of predicting uranium extraction rate in underground bacterial leaching of as-blasted ore has been developed. The method is based on the hypothesis that extraction is directly proportional to the volume of a piece of ore that is penetrated by the leaching agent, and that each piece of ore, regardless of size, has been penetrated radially from the external surface to the same depth at a given leaching time. Consequently, given an initial size and assay distribution, extraction should be predictable for a given penetration. Two laboratory bacterial leaching tests under simulated stope leaching conditions were carried out for a periods of 89 and 96 weeks. On completion, the residual ore was screened and analyzed. The information so obtained was employed to provide an elapsed time base for the penetration model, from which predictions of future extraction were made. The finding of solubilized uranium trapped within apparently sol id ore pieces was unexpected. However, it is not recoverable except after crushing, and hence does not affect calculations of underground leaching .

Jan 1, 1974

By I. B. Cadoff, J. C. Bilello, R. Rosenberg

Diffiusion of magnesium into the surface of LiF crystals to controlled depths and subsequent heat treatments provided a wide range of surface zone harahesses and structure, The bend strength of the LiF crystals was increased by as much as an or-dev of magnitude. Ductility was achieved when dislocation generation occurred in the diffusion zone or when dislocations penetrated to the surface from the intevior. A critical surface hardness of 130 to 140 kg per sq mm was found helozu which generation could take place in the diffusion zone and ahoue which the zone was impenetrable, This hardness was obtainable by several methods, among them the aging of quenched MgF2 -LiF solutions to produce MgF, precipitation. Maximum hardness was ohtained in quenched specimens with no visihle evidence of MgF,. Diffusion-zone formation followed a parabolic rate law and an activation energy of 20.9 kcal per mole was obtained for the process. RECENTLY, the properties of ionic crystals as related to surface condition have been receiving much attention, specifically the transitions between ductile and brittle behavior. Originally Joffe 1 showed that NaCl crystals could be made ductile by immersion in water and related this to the elimination of surface microcracks. Aerts and DeKeyser 2 and Gorur 3' have subsequently shown that ionic crystals are inherently ductile and are embrittled through contact with air. Machlin and Murray4 hypothesized that a layer of NaCIO3 produced by contact of ozone with NaCl induced embrittlement by acting as a barrier to outward dislocation flow. westwood,' Rosenberg and Cadoff,9 and Bilello and cadoff' have reported surface strengthening of LiF crystals by coating with a magnesium compound and then heat treating for adherence. The major effect of the coat was to inhibit dislocation-slip lines from reaching the specimen surface. westwoods showed microcrack formation and fracture to be caused by slip-band interactions at the surface. The material presented in this paper is an extension of the work reported earlier by Bilello, Rosenberg, and cadoff'6,7 and illustrates the wide range of surface properties and bulk behavior obtainable by use of heat-treated magnesium-diffused surface regions in LiF crystals. EXPERIMENTAL PROCEDURE The LiF single crystals were obtained from the Harshaw Chemical Co. Some batch to batch variation was observed; therefore all specimens for a given test series were cleaved from the same crystal. The typical dimension used was 1 by 0.1 by 0.40 in. Surface damage resulting from cleavage was removed by chemically polishing in a 2 pct NH4OH solution. Each group of specimens was given a vacuum anneal at 700°C for 4 hr to provide a base standard for measuring comparative effects of various surface treatments. To produce the reacted surface zone, the annealed specimens were immersed in a boiling suspension of MgF, in doubly distilled HzO, agitated slbwly for 30 sec, removed, and dried at room temperature. Uniform coatings of MgF, were deposited with a thickness of approximately 5 mils. It should be noted that this technique can be modified for use with crystals which are soluble in water by using boiling absolute alcohol as the dissolving medium. This was found effective for the coating of NaCl with MgF2. The diffused surface zone was obtained by annealing the coated samples at elevated temperatures in a vacuum of lob4 mm Hg. Penetration depth was controlled by varying the annealing time from 1/2 to 28 hr. After heat treatment, the samples were tested for bend strength and hardness. Load was applied by four-point bending in a hard-beam testing jig. Four-point rather than three-point bending was used to provide a wide area of constant stress and to minimize the effect of localized inhomogenities in the specimen. The deflection rate was 8 x min-' and the distance between knife edges was 1/4 in. Load-time curves were obtained from a chart recorder coupled to the machine and converted to resolved shear stress on the shear plane vs deflection, as plotted in the figures. The unstressed portions of the sample outside of the two outer knife edges were used for the microhardness studies. Microhardness measurements were made with a Bergsman tester attached to a Reichert metallograph. All hardness impres-

Jan 1, 1964

By Donald B. Gillies

PROBABLY the most critical and difficult period in an engineer's career is that between the completion of his college work and his attainment of professional recognition and accepted status in the industrial world. Upon leaving school the young graduate breaks his immediate ties with his educational institution and in a sense finds himself adrift. At this time in his life a society like our Institute has both the responsibility and the privilege of meeting a vitally important need in his professional life. Some of these young men are Student Associates, in the year after graduation, and some are Junior Members, but all need advice and assistance. In some respects this situation will be accentuated by the war. Not only will thousands of young engineers be mustered out of military service but the process we describe generally as industrial reconversion will make necessary many readjustments in personnel. About two years ago the Institute recognized the opportunity of helping the younger member to help himself by appointing a new standing committee to be known as the Committee on Professional Development of Junior Engineers. Herbert Hoover is Honorary Chairman and it is my privilege to serve as Chairman. The name of the Committee is not entirely satisfactory but it expresses the general objective. The present article is in the nature of a progress report of the work of this Committee.

Jan 1, 1945

By AIME AIME

THE STANDARD herewith submitted is the result of several years of research and consideration by the A.I.M.E. Technical Committee on Milling Methods. In the early work of this committee it was found necessary to undertake the development of a standard laboratory method for screen testing of ores. During the research stages the desirability of having this standard, when completed, approved as American Standard was brought out. In accordance with this idea, its initiation as a project of the American Standards Association (then the American Engineering Standards Committee) was approved by the latter body and the A.I.M.E. designated as sponsor. In 1929, the A.S.A., on recommendations of its advisory committee, the Mining Standardization Correlating Committee), authorized the A.I.M.E. to be sole sponsor for this project. The personnel of the Institute's Committee on Milling Methods was then increased to make it thoroughly representative of all diversified interests in the mining field. Two years ago the standard was circulated and has been given wide distribution. Early in 1932 the committee voted unanimously, with 38 affirmative votes, that the standard be recommended to the Board of Directors of the Institute for submission to the American Standards Association for approval as American Recommended Practice. This was accordingly done, at the Feb. 1.6, 1932, meeting of the directors, and the American Standards Association approved the standard on July 6; 1.932, designating it as ASA M5-1932.

Jan 1, 1932

By E. van Walsum

Tunneling methods through rock have, since the successful development of explosives, relied almost solely on blasting. Over the last ten years, rock-tunneling machines (moles) have been developed and some major projects have been carried out successfully with the use of such machines, which rely on the destruction of rock by mechanical means rather than blasting. Various other basically new methods are presently under study, such as the use of laser beams, water jets, etc. For practical purposes, there are presently only two methods commercially available: 1) blasting or 2) tunneling by mole. A contractor would choose at present either one method or the other. Both methods have their advantages and disadvantages (Fig. 1). The thought has occurred that the next practical development in rock- tunneling technology might be a combination of the best features of the mole technique and those of the blasting technique. A preliminary evaluation of this approach indicated that there is definitely a good potential for fruitful developments along these lines. My purpose is to place on record some of the thinking and some of the ideas which were developed along these lines and to point out certain areas where development efforts are required. In trying to find an improved tunneling technique, we looked in particular for the following qualities: 1) safety, 2) continuity, 3) uniformity, 4) automation, and 5) flexibility. TUNNELING BY BLASTING Conventional tunneling by means of blasting proceeds generally in recurring sequences of events: 1) drilling, 2) loading, 3) firing, 4) mucking-out, and supplementary operations (such as scaling and lining). These four operations (drilling, loading, firing, mucking) proceed one after another.

Jan 1, 1970

By CHARLES M. A. STINE

IN fighting a war the all-absorbing intent is to win. There is little time to analyze the rush of events or to appraise their consequences beyond the war's end. The united objective is, rightly, success for our arms. Yet under the pressures of a great war there may be compressed scientific, economic and social developments that might have taken many decades to achieve under less urgent conditions. Their effects on our lives and all civilization may be more wide-reaching and lasting than any military conquest. They constitute one of the must imperative incentives to victory. No American, least of all any scientist worthy the name, conceivably could endorse war as a justifiable means to progress. The destruction of life and property wrought by the present war far exceeds the havocs of a century's earthquakes. Most of mankind is burning itself on an altar of paganism. Nonetheless, one fact is inescapable Despite the recurrent malady of war history's overall course is forward. Mankind has the habit of rising phoenix-like from its own ashes to attain greater heights. Progress is immortal.

Jan 1, 1942

By R. W. Raymond

(Chattanooga Meeting, October, 1908.) THE immense commercial value of the Gayley dry-blast process has been established beyond controversy. The testimony of practical blast-furnace managers, on both sides of the Atlantic, agrees that it reduces the cost of pig-iron about $1 per ton; but from the same testimony it appears that this direct economy does not by any means cover its commercial advantages-in fact, that under conditions frequently encountered in practice, it presents other benefits of even greater immediate financial importance. To this point I shall recur in a later part of the present paper. The history of the reception given to this invention, especially on the other side of the Atlantic, has repeated an experience familiar to American engineers. First, the reports of our practice were rejected as theoretically impossible, according to generally accepted notions and formulas; then the figures were reluctantly accepted ; and finally the attempt has been made to explain how they could have been obtained. As to the Gayley dry blast, we Americans have been for several years in the last stage of the discussion, and the rest of the professional world is rapidly coming to it. Meanwhile, the remark has been repeatedly made that, whatever Mr. Gayley's process may turn out to be worth, it was not an invention on his part, but simply the energetic and persevering execution of a procedure already proposed by others. This question I wish to discuss first in the present paper. I. WHAT DID MR. GAYLEY INVENT Realizing that this is not the place for detailed argument on an issue of patent law, I shall not undertake to quote and criticise the publications prior to Mr. Gayley's first patents. It may be admitted, without such critical analysis, that the possi-

Jan 1, 1909

By H. Hubert

THE first attempts at direct utilization of blast-furnace gas in engines were made in 1895. For a considerable time the gas had been burnt in Cowper stoves for heating the blast for the furnace, and under the boilers which supplied steam to the blowing-engines, and others serving the furnaces. It was natural, therefore, that the idea of directly employing it in gas-engines should have occurred simultaneously to several engineers, notably to Lürmann and to Lencauchez, who had pointed out the blast-furnace as a powerful -gas-producer. Nevertheless, nowhere had any attempt been made to apply it to this purpose up to the end of 1894, when Thwaite proposed it to Mr. James Riley, of the Glasgow Iron & Steel Company. About the same time investigations were being made in Belgium and in Germany, independently of Thwaite's experiments, which were not generally known on the Continent. The industrial world, which up to that time had hardly favored the idea, had thus been gradually prepared to receive it. The gas-engine, long restricted to small sizes and dependent upon the use of an expensive fuel obtainable only in large centers, now began to make headway. At the Paris Exhibition of 1889 two engines of 100 h.p. were shown and excited much interest among engineers. One had four cylinders, and was made at the celebrated works of the Deutz Company, and the other was a single-cylinder engine, exhibited by two French designers, Messrs. Delamare-Deboutteville and Malandin. In the meanwhile the design of gas-producers had made important progress, completely freeing the new engine from its

Nov 1, 1906

Edward S. Simpson, Perth, Western Australia (communication to the Secretary): In 1896 the East Coolgardie gold-field was divided into three fields, viz. : Area, square miles. Officia1 Centers. (1) East Coolgardie,. . 634 Kalgoorlie. (2) Broad Arrow,. , 588 Kurawa. (3) Northeast Coolgardie,. 22,960 Kanowna. The whole of the area embraced by the eastern gold-fields is covered with late Tertiary sands and gravel, with occasional beds of clay shales. These mostly overlay granite which occasionally shows through in small round hills. At Coolgardie, Kalgoorlie and other mining centers, belts of diorite, serpentine and highly metamorphosed sedimentary rocks appear on the surface. The rainfall at Kalgoorlie in 1897 was 4.75 inches. That the climate has not always been so arid is evidenced by the recent discovery at Coolgardie (only twenty-five miles away) in the late Tertiary formations of a thick bed of brown coal, containing numerous fossil fern-leaves. As assayer and mineralogist to the Government of Western Australia I have had occasion to examine a large amount of the Kalgoorlie ores, both in Perth and at the mines at Boulder itself. The only tellurides I have been able to determine are

Jan 1, 1899

By Edgar L. Weinberg, W. Horatio Brown

The Austinville-Ivanhoe lead-zinc deposit occurs in the Lower Cambrian Shady dolomite. This deposit is located in southwestern Virginia in the faulted and folded Appalachian Valley and Ridge province. The ore bodies resemble the chimmey and manto deposits of northern Mexico and are formed by replacement and filling. They are confined to certain favorable zones of the Austinville and Ribbon members of the Shady. Structural and stratigraphic factors combine to control the location and form of the ore bodies. In certain places secondary oxide enrichment of the zinc minerals has contributed to the economic development of the area. It is concluded that the ore is epigenetic and is deposited by hydrothermal solutions rising through the fault "plumbing." Classification is epithermal-telethermal.

Jan 1, 1968