Search Documents

By P. E. Fitzgerald

SOME readjustments in the research programs of most of the oil companics and petroleum engineering schools have been made necessary by the war. The most obvious change has been the conversion from production engineering to problems more closely related to the nation's was effort. Many laboratories now devote much of their time to studies on products to be derived from petroleum. such as synthetic rubber, toluene, and substitutes for critical materials. Others are working to improve motor fuels including high-octane gasoline and the special lubricants required by the wide geographical range of the present conflict. Of great importance is the experience of the geophysicists, who are now devoting a great percentage of their time on instrument research and production or special apparatus required by the armed forces.

Jan 1, 1943

By Warren W. Jamar, Philip D. Pearson

IN recent years, there have been many changes in mining operations in the Lake Superior district. To follow these trends on the Menominee Range of Michigan, information has been assembled from all of the iron informatior]mining operations in the area. There are 15 operating underground mines in the Iron River-Crystal Falls area of the Menominee Range. Within the past two years, two idle properties were reopened pasttwoyears,and are now producing, and a third and fourth are being reopened. Also, there are two siliceous openpits operated by independent companies outside this immediate area. Six companies operate the underground mines, employing some 1850 employees. Table I shows pertinent facts about these properties. During 1949, the largest mine in Iron County shipped 571,287 tons, and one of the newer mines shipped 39,378 tons, with a range total to 3,535,-373 tons. Since the Menominee Range was opened in the 1870's, the mines in Iron County have shipped 85,890,922 tons. From an operator's viewpoint rather than a geologist's, the ore is' classified as semi-hard, composed of hematite and limonite. It is not as soft as the ores of the Marquette Range nor is it as hard as the hard ores of the Marquette and Vermillion Ranges. The ore bodies have slate hanging walls and slate footwalls. In most cases the hanging walls and footwalls are soft and high in sulphur. The sulphur comes from pyrite, and these slates will ignite when piled more than 6 to 8 ft high. Ore is mined on this range by: 1—Sub-level stop-ing; 2—Shrinkage stoping; 3—Sub-level caving; 4— Block caving; 5—Top slicing. The predominance of these methods is in the order named. Underground drilling is important in the mining cycle. Some changes made and trends toward future changes fall into four categories: Drill bits, drill steel, drill machines, and compressed air pressures. Several types of bits have been tried and are in use. They include the detachable tungsten carbide, insert bit; the intraset steel bit, which is a conventional steel rod with tungsten carbide insert; the one-use bit; and the multiple-use bit. For many years, detachable multiple-use bits have been standard. In tests conducted recently to im- prove drilling efficiency, this bit was used as the basis for comparison. Under existing conditions, a multiple-use bit can be resharpened about three times before it is discarded. A thorough test of 2-in. tungsten carbide threaded bits was conducted under various ground conditions. 1—The drilled footage ranged from 48 to 600 ft per bit; averaging 357 ft per bit. Under these same conditions, a multiple-use bit ranged from 8 to 80 ft per bit. 2—The bit cost was greater for the insert bit in each case. 3—The average drilling speed for the insert bit was 12 in. in 62 sec and for the multiple-use bit was 12 in. in 64 sec. In a second test, 2V4 -in. tungsten carbide bits with the large 1 3/16-in. thread were used in moderately soft ground on a 152-lb drifting drill on a long feed jumbo. 1—The drilled footage ranged from 450 to 5000 ft per bit, averaging 1810 ft per bit. Under these same conditions, a multiple-use bit averaged 64 ft per bit. 2—The bit cost was reduced by the use of the insert bit. 3—No increase in drilling speed was recorded. 4—Minimum footage obtained was caused by thread failure. To improve the thread life, thread size on the rod was increased and the bit was attached to the rod with a pipe wrench. After this, bits failed in equal proportions because of cracked skirts, broken inserts, and gage loss. Tungsten carbide bits are now used in the operation where this second test was conducted because labor costs were lowered as a result of reducing the number of bits being changed by the miners. At the same operation and under the same conditions as the second test, 1Y4-in. insert bits with standard 1-in. threads were used. These bits did not drill much more than 300 ft before thread failure and were then welded to the rods and used until total failure. Sometimes this footage was considerable, sometimes it was not. Chisel-type 2%-in. insert bits were

Jan 1, 1952

By Arvid E. Nissen, Knox Taylor, John H. Hall

Some months ago one of the authors was asked to write a paper on the heat treatment of steel castings that would be more comprehensive than other matter he had published; this is an attempt to present in condensed form the results of experimental work and actual practice carried out for the most part in 1907, 1908, and 1909. It is not a laboratory research and the work done was carried out for the express purpose of putting in practice the processes discovered as fast as possible. Most of the tests are the result of commercial practice and not of bars annealed in our laboratory; most of the micrographs were made for our own records and not for publication. Certain of the micrographs, therefore, are not as clear as we may wish but they were good enough for our purpose at the time they were made. The tests and micrographs are selected from several thousands in our files. All of these micrographs are magnified 60 diameters. These experiments were conducted almost entirely on steel made in a 3-ton bottom-blown converter, and most of the steel illustrated analyzes about 0.05 in phosphorus and sulfur. Unfortunately, a certain number of specimens are shown of which we do not have the complete analysis, but in most cases in which the phosphorus and sulfur vary much from the figure just given that fact is noted. For purposes of comparison, we have included a certain number of micrographs and tests of steel made in the electric furnace, some of which were from specimens made in other shops and some in our own shop, and some tests of acid open-hearth and tropenas steel. A brief examination of the tests in Table 1 shows that certain treatments of, for instance, 0.30 per cent, carbon steel are not represented by any test data. Had this been a laboratory research, this information would undoubtedly have been furnished, but as this work was done for commercial purposes the omissions are due to the fact that, at the time the work was done, we saw no advantage in trying every composition of steel with each treatment discussed in the paper.

Jan 1, 1920

By J. A. Clum, R. W. Heins, T. D. Tiemann

The use of Na-montmorillonite clay hinders (Western Bentonite) in the pelletizing of iron ore concentrates is well established as is the idea that alternative binders must be found. 1-6 This note summarizes work done7 in evaluating a Wisconsin montmorillonite clay binder. The clay occurs in irregualr beds overlying the Prairie du Chien Dolomite and the St. Peters Sandstone near Hersey, St. Croix County. The raw Wisconsin clay contained 65% quartz and 35% clay minerals. The Na20to CaO ratio was 0.234. Suspension viscosity tests of the raw clay gave results only slightly better than water alone, even after treatment with activator materials. Sedimentation treatment reduced the quartz in the decantate to 5% after 240 min (four hours). Twenty minutes of sedimentation produced a decantate with 27.5% quartz which was found as effective as the 5% quartz decantate in pelletizing behavior. The 20 min decantate was used in subsequent tests. The decantate was filtered and dried at 110°(230°F). The minus 200 mesh portion of this was added directly to the magnetite concentrate. Pellets were made in a laboratory sized disc pelletizer from pastes consisting of ore concentrate, balling water (9%) and binder (clay, or clay + resins, or resins). The pastes were premixed in a Waring blender. The binders were: (1) 1% of a commercially used Western Bentonite; (2) 1 % or 3% of the Wisconsin clay (raw, or 20 min decantate); (3) 20 min decantate washed with activator solutions, (to exchange Na for Ca in the clay); (4) decantate with activator added in the balling water; (5) decantate with organic resins; (6) organic resins. Measurements of the 0.46 m (18 in.) Green Drop Number, the Dry Strength and the Fired Strength (fired at 1260°C (2300°F) for 30 min) were made. The dry and fired compressive strengths were determined on an Instron testing machine using a C-load cell and a F-load cell, respectively. The cross-head speed was 0.004 m/sec (0.1 in./min) for both. The results of each measurement were averaged for 15 pellets. A summary of those results is presented in [Table 1]. More detailed results and procedures are presented in another report.7 In addition to the effects on pellet strength due to various binders the effect of varying magnetite concentrate characteristics is noted in [Table l]. There, a few comparative data are shown for Cornwall, PA Magnetite, which has a generally liner particle size than the Black River Falls magnetite which was used for most of the tests.

Jan 1, 1979

GENTLEMEN : Herewith are submitted reports for the calendar year 1933 of your Treasurer and the Chairmen of the following standing committees: Finance, Admissions, Membership, Papers and Publications, Library, and MINING AND METALLURGY. TO these reports you are referred for additional details of the year's activity. Finances.-Income for 1933 from all sources totaled $121,690 com- pared with $138,331 in 1932. Incidentally, this exceeded the income as estimated in the budget by $7,190; the largest item being a "surplus" of $3,316 over the budget expectancy as to member dues. As compared with 1932 the most important items of shrinkage in income were $9,000 from dues and initiation fees; $5,500 from the magazine, MINING AND METALLURGY; and $2,500 from sales of publications other than the magazine.

Jan 1, 1934

Abbey, Robert Graham, District Mgr.. The W. W. Sly Mfg. Co., 50 Church St.. New York, N. Y. '21 Abbott, A. N., Mines Supt., Mazapil Copper Co., LtdConcepcion del Oro, Zac., Mexico. '28 *Abbott, Argyle Campbell, Dev. Dept., E. I. du Pont de Nemours & Co., Wilmington, Del. '29 Abbott, Clarence E., V.P., Charge of Raw Materials, Tenn. Coal, Iron & R. R. Co., 1242 Brown-Marx Bldg.. Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr., Elkhorn Div., Consolidation Coal Co., Jenkins, Ky. '16 Abeel, George H., Jr., Cons. Min. Engr Box 427, Santa Monica, Cal. '18 Abel, Albert E., Asst. to Pres., Valley Mould & Iron Corp Hubbard, Ohio. '19 Abel, Raymond L., Asst. Prof., Dept. of Pet. Refin., Univ. of Pittsburgh Pittsburgh. Pa. '28 Abeel, Leo M., Research Engr., Sullivan Concentrator Chapman Camp, B. C., Canada. '31

Jan 1, 1929

By Mark R. Lamb

THE various methods of treating pulp in air-agitation tanks offer problems for experiment and study which are fascinating as well as practical. The usual method heretofore has been to fill each tank in turn, agitate the mixture the required period and then discharge the treated pulp into a storage-tank, from which it. is drawn to the filter as required. A later method is to run the pulp from the tube-mill, classifier, thickener, or settler into the first of a set of tanks, and thence continuously or in series through the remaining tanks, finally drawing off the pulp to a continuous filter, or to a pulp-storage tank if the filter is of the intermittent type. It is this method which I propose to discuss here in a preliminary way, with the idea of going exhaustively into the examination of the results of a series of experiments in a later paper. It may be of interest to note that the design of a cyanide-plant has recently been completed in which the estimated cost of the agitation-tanks, storage-tanks, and pumps was 30 per cent higher for the charge-agitation arrangement than for the series plan. The first question in studying the series method is, "What is the actual period of treatment undergone by the pulp?? One first supposes that by chance some of the pulp may get through with little or no treatment, while other portions may stay in the tanks a needlessly long period. The former is not probable or even possible, and the latter is, practically, true to only a limited extent. The greater the number of tanks the greater is the percentage of chance that all the pulp will be treated equally. Without going into the mathematical analysis of the problem (which is of little value, since it is based on problematical premises), its important terms may be clearly grasped by thinking of, or " visualizing," the conditions when,

Jan 1, 1910

By AIME AIME

MINERALS and mineral resources are recognized as one of the things that nations are prone to quarrel about. The territory that was arbitrarily incorporated into the Polish Republic after the World War produces a variety of essential minerals on a substantial scale. The accompanying table has been compiled to give some idea of the relative importance of this production. Poland, before the recent war started, had an area of 150,000 sq.mi., just a little larger than the State of Montana. Its population was 32,000,000, equal to that of New York, New Jersey, Pennsylvania, Connecticut, and Massachusetts. Though not a highly industrialized country it nevertheless has important mines, steel plants, petroleum refineries, and sundry metal-fabricating manufactories. Coal, petroleum, iron and steel, zinc, lead, pyrite, potash, and salt are produced in excess of the country's domestic consumption. It has no appreciable production of copper, chromium, tungsten, nickel, tin, mercury, manganese, aluminum, magnesite, fluorspar, or graphite.

Jan 1, 1939

By C. S. Smith, L. H. Beck

KNOWLEDGE of the Cu-Zn constitution diagram was critically examined in 1944 by G. V. Ray-nor,1 who suggested the diagram reproduced in Fig. 1 as the best evaluation of available data. No pertinent work on the constitution has been published since that time, although a number of authors have discussed transformation kinetics and theory. Despite the large amount of work that has been done on the constitution of these industrially important and scientifically interesting alloys, minor uncertainties still exist. For example, it is still not possible to say definitely whether a two-phase region exists between the ordered and disordered forms of the 8 phase. A careful re-examination of the phase boundaries in this part of the diagram was therefore undertaken. Two methods were selected for the new investigation—quantitative metallography for the higher temperatures and precision lattice parameter measurement for lower temperatures. Because of the relatively narrow two-phase regions flanking the ß phase in these alloys, quantitative metallography is particularly suited for their examination, since the relative amounts of the two phases are very sensitive to their compositions. The method, however, is useless below about 350°C because of the inadequate resolution of the two constituents. Below 400°, however, the X-ray diffraction method is applicable, although it is of somewhat lower sensitivity in this system. The changes of composition that occur during quenching from above about 500°C entirely vitiate X-ray measurements at room temperature though they do not affect metallographic area measurements. The two methods overlap and supplement each other admirably. Both methods depend on the attainment of equilibrium composition of the two phases in a more or less intimate mixture and thus avoid the difficult problems of nucleation and long range diffusion involved in the conventional metallographic bracketing method. The alloys were melted from a master alloy made from re-electrolyzed cathode copper and Horsehead 99.99 pct Zn. Melting was done under a cover of either borax or charcoal and the alloys cast into a 7/8 in. sq graphite mold for the a-ß alloys or a 3/8 in. diam cylindrical graphite mold for the ß-? alloys. The a-ß alloys were rolled at 750°C to 5/8 in. sq; annealed for 24 hr at 800°C and quenched; then rolled and swaged at 200°C to 3/8 in. diam rods, annealed 24 hr at 200°C, quenched and cold rolled 2 pct reduction. This treatment was intended to obtain a small grain size and to produce many nuclei of the minor phase for growth on subsequent heat treatment. The unworkable ß-? alloys were given preliminary treatment by sealing in Vycor tubes in vacuum and annealing for 4 hr at 800°C followed by cooling in air. Samples of homogenized alloys were checked spectrographically for impurities, but the principal components were determined on samples subsequent to heat treatment. The impurities analyzed averaged approximately as follows: Ag, 0.0002 pct; Fe, 0.004; Si, 0.0008; Cd, 0.005; Mg, 0.0002; and Pb, 0.002. For metallography, samples of appropriate composition were cut into rods 5/8 in. long, sealed in pyrex tubes in vacuum and annealed for eight weeks at temperatures of 470°C and below, two weeks at 480°, 500°, and 600°C, and 4 hr at 700°C, followed by quenching in cold water. Temperatures were accurate to ±2°C. The cylinders were then machined to 8.7 mm diam and a slice weighing 1.5 g cut with a thin saw transversely from the center of each. This

Jan 1, 1953

By N. V. Melnikov, L. N. Marchenko

The latest theoretical and experimental study of physical processes initiated by explosions in solid media have made it possible to obtain a deeper insight into the mechanism of the energy transfer to ambient rock from char es of explosives interspersed with various air gaps. As shown in (17, high explosive action causes excessive fragmentation of medium in the vicinity of the charge, while expansion of the process into the massif is negligible. A theoretical outline of a more rational application of explosion energy was given with a view of obtaining more uniform fragmentation of rock convenient for loading and transportation. The proposed idea proven by experimental study consisted of the possibility of explosion control based on redistribution of explosion energy. Practical realization of the above idea was proposed (1) involving charges with air gaps for rock fragmentation. Since the Rolla Symposium on Mining Research (USA, 1961) (2), borehole charges with air gaps have become common practice. This method of rock blasting is applied in open cast and underground mines working the hardest and viscous, hard, medium hard and soft rocks (ore, quartzites, granites, 1 imes tones, sandstones, coals, etc.) as well as at enterprises for extraction of building materials and raw chemical minerals of any strength. Application of charges with air gaps results in an increase of the degree and uniformity of fragmentation (up to 94 percent of the blasted rock mass consists of fragments not exceeding 400 mm), the average fragment size decreases by 1.5-2 times and the amount of lumps is reduced by 2-10 times (in some cases there are no lumps at all ). Besides, the amount of operation for filling boreholes with tamping material is reduced, the specific consumption of explosives

Jan 1, 1971

By E. W. Dewing

The solubility of A14C3 in cryolite melts has been determined by holding the melt with aluminum in a graphite crucible for 4 hr at temperature, quenching the crucible in water, and analyzing the frozen salt by CH4 evolution. The solubility is given by log(wt % Al4C3) = 1.298 -1.l74 (wt ratio NaF/AlF3) independent of temperature in the range 985" to 1080°C. Additions ofA1203, .NaCl, CaF2, or LiF up to 10 wt pct do not affect the solubility, provided that LiF and CaF2 are replaced by equivalent NaFin calculating the ratio. The variation with ratio can be accounted for quantitatively on the hypothesis that the Mechanism of solution is Al4C3 + 2AIF3 = 3Al2CF2 since the solubility varies as (aAIF3) 2/3; Mechanisms involving C", C2- , AlC- , A12C2+, and Al2CF+are re-jected. At ratios above 1.5 truces of c;- are also present. It was noticed some years ago in this laboratory that carbon specimens made cathodic in a cryolite bath decrease in diameter over a period of time.' It was also found that cryolite which had been melted with aluminum in a graphite crucible was sometimes yellow, and that A14C3 could be seen intimately embedded in the cryolite crystals. CH, could be recovered by acid attack. There was thus reason to believe that A14C3 had a genuine solubility in molten cryolite, and the object of this work was to measure it. EXPERIMENTAL AND RESULTS A graphite crucible, 2 in. ID and 2.5 in. deep with a close-fitting lid, contained about 150 g of cryolite (plus additives) and about 20 g of 99.99 pct pure Al. It was placed in a vertical Inconel furnace tube, covered with refractory brick to provide thermal insulation, and the top of the tube was roughly sealed with disks of asbestos paper. An alumina tube led argon down to the level of the top of the crucible to expel air, and an alumina sheath with a Pt-10 pct Rh ther-mocouple inside was positioned between the crucible and the wall of the Inconel tube. The tube was heated in an electrical resistance furnace for the desired length of time; the refractory bricks were then removed, and the crucible was lifted out with tongs and quenched in water. After such a crucible was broken open it could be seen that its inner surface was yellow owing to the presence of A1,C3, and sometimes needle-like crystals could be observed (at X75 magnification) growing out into the nielt. It was concluded that Al,C, had been present as a separate phase when the crucible was at tenlperature and that the melt had been saturated: in

Jan 1, 1970

By Herbert Clark Hoover, Lou Henry Hoover

IN the last book I have explained the methods of delimiting- the meers along each kind of vein, and the duties of mine officials. In this book1 I will in like manner explain the principles of underground mining and the art of surveying. First then, I will proceed to deal with those matters which pertain to the former heading, since both the subject and methodical arrangement require it. And so I will describe first of all the digging of shafts, tunnels, and drifts on venae profundae; next I will discuss the good indications shown by canales2, by the materials which are dug out, and by the rocks ; then I will speak of the tools by which veins and rocks are broken down and excavated ; the method by which fire shatters the hard veins ; and further, of the machines with which water is drawn from the shafts and air is forced into deep shafts and long tunnels, for digging is impeded by the inrush of the former or the failure of the latter ; next I will deal with the two kinds of shafts, and with the making of them and of tunnels ; and finally, I will describe the method of mining venae dilatatae, venae cumulatae, and stringers.

Jan 1, 1950

By N. H. Mannakee

SINCE the publication of the paper of Mr. Scholz, The Effect of Humidity on Mine-Explosions,' I have undertaken a study of the meager available data of barometric and temperature conditions it times of mine-explosions, and have arranged these data in a manner which may be of interest to other students of mine-explosions. This study covers the period from 1898 to 1909, during which an ever-increasing percentage of collieries has been ventilated by fans giving air-currents of high efficiency. Previous to 1898 this percentage was smaller than at any time since. The vari¬ous States have become, from time to time, more exacting in their demands upon poorly-ventilated mines. This general im¬provement in ventilation throughout the Appalachian field has undoubtedly brought about a condition which is annually the cause; .or a very important attendant, of the high percentage of fatalities in mine-explosions, through the daily passage of from hundreds to thousands of gallons of water, invisibly suspended in the air, carried out of the mines by the ventilating-currents during the existence of certain temperature- and humidity-conditions. There is a wide-spread opinion that these conditions exist from November 1 to March 31; but it is more likely that they have a much wider range, which varies from year to year. Certain years show an increase or decrease of rain-fall from the mean ; the daily temperature may fall far below or rise far above the mean established by a record of a period of years; and the daily humidity varies likewise. If mine-explosions are influenced by a lack of moisture in the mines, certainly it may be expected that the influence will be felt at times when the

Nov 1, 1909

By G. F. Loughlin

MORE than 20 years have passed since the publication of Lindgren and Ransome's report on the Cripple Creek District,1 which was made when the district was much more active and prosperous than in recent years. They concluded that the output of the district, which had reached its maximum of about $18,200,000 in 1900, would gradually decline, and their conclusion has been confirmed by records of subsequent production. Between 1905 and 1915 annual declines were partly compensated by encouraging increases, especially in 1908, 1914, and 1915; but a rapid continuous decline followed, due largely to the war and its after effects, until in 1922 the value of output was only slightly more than $4,000,000. It rose to nearly $5,000,000 in 1924, but declined again in 1925 and in 1926, when it was about $4,400,000, and represented ores mainly from deep levels in the Cresson and Portland mines. The profitable operations of these two mines were the principal factors leading to a study of ore at deep levels in the district by the U. S. Geological Survey in coopera-tion with the Colorado Metal Mining Fund. The principal reasons for Lindgren and Ransome's conclusion were three: (1) the greater cost and difficulty of deep exploration; (2) the decrease in the number of veins with increasing depth, and (3) the probability that the telluride ore, believed to have formed at comparatively low temperature, would not persist indefinitely -in depth. Operations since they made these statements have verified the first two, but call for some modification of the third. Rich telluride, ore is being mined at a profit in the Portland mine 3000 ft. below the present surface, or 5000 ft. below the original surface of the Cripple Creek volcano, as interpreted by Lindgren and Ransome. The question arises, therefore, as to the number and extent of such deep deposits, and the answer, so far as it can now be given, must be based mainly on structural data, supplemented by data on the processes of ore deposition. Presentation of these data based on a study of deep mines in the southeast quarter of the district, the only

Jan 1, 1927

NEW MEMBERS The following list comprises the names of those persons who became members during the period Nov. 10, 1916 to Dec.10, 1916. BARNSDALL, THEODORE N., Treas. & Mgr., Highland Gas Co., 24 West Corydon. St., Bradford, Pa. BEASLEY, FRED E., Asst. Supt., Copper Refinery, Consolidated Mining & Smelting Co., Trail, B. C., Canada., BREWSTER, THOMAS T., Vice Pres., Gen. Mgr., Mt. Olive & Staunton Coal CO., 1012 Federal Reserve Bldg.,-St. Louis, Mo. BRINDLE ARTHUR ST. C.... Mining Recorder's Office, Trout Lake, B. C., Canada. BULLOCK, Harry E., Pres Kentucky-Jewel Coal Co., Lothair, Ky. BUTLER, PERCY BENNETT, Mine Operator :..P. 0. Box 335, Joplin, Mo. BUTLER, ROBERT S Supt., Three Johns Mining CO., ,Joplin,.Mo. CABOT, Godfrey, L., Carbon Black Maker, Gas Engr., 940 Old South Building Boston Mass.

Jan 1, 1917

By E. L. Kinsella, F. S. White

Solids fluidization utilized in two ways for the commercial production of lime is described. Crushed —6 mesh limestone is dried and dedusted in a single bed reactor, then calcined in a 5-stage reactor. Construction, operation, and results obtained with both processes are given. THE solids fluidization process brought out by the Standard Oil Development Co. in the early forties for catalytic cracking of petroleum enabled rapid transfer of large quantities of heat from gases to solids under closely controlled temperature conditions. As the technique developed, it was natural that applications for the process outside the petroleum industry would be sought. The calcination of limestone to quicklime requires the transfer of a large quantity of heat at high and closely controlled temperatures. For these reasons, this possible application was one of the first to be investigated. Laboratory work conducted by the Dorr Co. indicated that lime produced by solids fluidization would be of exceptional quality. Calculation of theoretical heat balances showed that savings in fuel could be expected. Accordingly, a pilot plant of 10 tons per day capacity was erected by the New England Lime Co. at Adams, Mass., to substantiate the process. Operation of the pilot plant, previously described,' showed that excellent lime could be produced with a saving in fuel. The work also indicated the necessity of preparing feed to remove the finer fractions if dust losses were to be held to a tolerable level. A single-stage fluidized solids drier-stripper was developed to accomplish this sizing.' Subsequently a commercial lime reactor was erected at Adams, beginning operation in June 1949, followed by air sizer facilities completed in November 1951. This paper will describe these two applications of solids fluidization. The raw material for preparation of lime by the fluidizing process is a high calcium crystalline lime- stone having the approximate chemical composition shown in Table I. The stone is first prepared by crushing and grinding in conventional equipment to pass a 6-mesh sieve. After crushing, the material is sent to the FluoDry unit for drying and dedusting. Fluidized Drying and Sizing As shown in Fig. 1, the FluoDry unit consists of a -in. cylindrical steel shell, 9-ft ID by 22-ft 6-in. overall height. Attached horizontallv at the bottom is a 6-ft diam combustion chamber, approximately 7 ft 6 in. long. A refractory constriction dome, consisting of first-quality fire brick shapes, partitions the inside into two sections. The lower section is called the windbox and the upper the bed compartment. The vertical wall of the shell is lined with 6-in. first-quality rotary kiln blocks. In the bottom of the windbox a hoppered section is formed with castable refractory to permit the windbox to be readily cleaned via a 6-in. screw conveyor. The combustion chamber is similarly lined with refractory shapes. On the 6-in. diam section, 4 in. of insulating brick, HW-26, are used. The inner combustion chamber is lined with 4-in. Korundal brick to withstand the high flame temperatures encountered. An 8-in. steel feed pipe, entering vertically through the top and fitted with an air-operated cone valve,

Jan 1, 1953

By F. S. White, E. L. Kinsella

Solids fluidization utilized in two ways for the commercial production of lime is described. Crushed —6 mesh limestone is dried and dedusted in a single bed reactor, then calcined in a 5-stage reactor. Construction, operation, and results obtained with both processes are given. THE solids fluidization process brought out by the Standard Oil Development Co. in the early forties for catalytic cracking of petroleum enabled rapid transfer of large quantities of heat from gases to solids under closely controlled temperature conditions. As the technique developed, it was natural that applications for the process outside the petroleum industry would be sought. The calcination of limestone to quicklime requires the transfer of a large quantity of heat at high and closely controlled temperatures. For these reasons, this possible application was one of the first to be investigated. Laboratory work conducted by the Dorr Co. indicated that lime produced by solids fluidization would be of exceptional quality. Calculation of theoretical heat balances showed that savings in fuel could be expected. Accordingly, a pilot plant of 10 tons per day capacity was erected by the New England Lime Co. at Adams, Mass., to substantiate the process. Operation of the pilot plant, previously described,' showed that excellent lime could be produced with a saving in fuel. The work also indicated the necessity of preparing feed to remove the finer fractions if dust losses were to be held to a tolerable level. A single-stage fluidized solids drier-stripper was developed to accomplish this sizing.' Subsequently a commercial lime reactor was erected at Adams, beginning operation in June 1949, followed by air sizer facilities completed in November 1951. This paper will describe these two applications of solids fluidization. The raw material for preparation of lime by the fluidizing process is a high calcium crystalline lime- stone having the approximate chemical composition shown in Table I. The stone is first prepared by crushing and grinding in conventional equipment to pass a 6-mesh sieve. After crushing, the material is sent to the FluoDry unit for drying and dedusting. Fluidized Drying and Sizing As shown in Fig. 1, the FluoDry unit consists of a -in. cylindrical steel shell, 9-ft ID by 22-ft 6-in. overall height. Attached horizontallv at the bottom is a 6-ft diam combustion chamber, approximately 7 ft 6 in. long. A refractory constriction dome, consisting of first-quality fire brick shapes, partitions the inside into two sections. The lower section is called the windbox and the upper the bed compartment. The vertical wall of the shell is lined with 6-in. first-quality rotary kiln blocks. In the bottom of the windbox a hoppered section is formed with castable refractory to permit the windbox to be readily cleaned via a 6-in. screw conveyor. The combustion chamber is similarly lined with refractory shapes. On the 6-in. diam section, 4 in. of insulating brick, HW-26, are used. The inner combustion chamber is lined with 4-in. Korundal brick to withstand the high flame temperatures encountered. An 8-in. steel feed pipe, entering vertically through the top and fitted with an air-operated cone valve,

Jan 1, 1953

By G. G. Brown

Enthalpy-entropy diagrams are presented for natural gases of 0.6, 0.7, 0.8, 0.9, and 1.0 gravity over the pressure range of 5 to 10,000 Ib. per sq. in. and temperature range of 32º to 700°F. The charts indicate directly the work requirement and temperature rise for adiabatic compression or temperature change for free emansion of natural eases. Computation and Uses of Charts The Mollier diagram (Fig. 4), in which the enthalpy (heat content) is plotted against the entropy with lines of constant temperature, pressure,, and in some cases volume, has been found most convenient when dealing with the compression, expansion, and flow of fluids. In dealing with the flow of fluids, the sum of the increase in the enthalpy, AH, plus the increase in kinetic energy, AM —, plus the increase in potential energy, ?MZ, representing the total increase in energy of the fluid in flow, is equal to the sum of the heat q, and work added, —w, to the fluid while flowing between the entrance and exit of the flow system. AH + AM— + ?MZ = q-w [1] In cases where there is no significant change in potential energy or in kinetic energy (velocity), it follows that the increase in enthalpy is equal to the total energy supplied to the fluid. Under such conditions' the changes in the property of the fluid as it flows through a throttling valve, choke, or any other similar arrangement, may be read directly from the enthalpy-entropy diagram by following a horizolltal line between the known pressures' When compressing Or expanding a gas by means of a Or or engine in which no heat is added to or subtracted from the gas, but only work done, the changes in the properties of the gas may be determined along a vertical line of constant entropy between the entering and exit pressures. The power required for the compression of the gas may be readily determined by converting the increase in enthalpy into the desired units. The enthalpy-entropy diagram for natural gases is to the gas engineer what the steam diagram is to the steam-power engineer. For this reason it would be extremely convenient if a reasonably satisfactory enthalpy-entropy diagram could be prepared as a function of the gravity of the gas. A careful study of the known properties of natural gas indicate that this is possible. The effect of temperature upon the enthalpy at constant pressure is expressed as the "heat capacity" or "specific heat" of the gas. The best available data for natural and petroleum refinery gases indicates the relationship shown in Fig. I. From this it is clear that the specific heat of natural gases is a function only of the gas gravity and the temperature at atmospheric pressure. The effect of pressure on the enthalpy of natural gases is dependent upon the pressure-volume-temperature relationships,

Jan 1, 1945

By Strathmore R. B. Cooke, Marcus Digre

That calcium will activate quartz for flotation with anionic collectors such as soaps has been known for a number of years,12'3 and the method has been applied to the concentration of various iron ores4 5 6 as well as to other materials. Clemmer gives the permissible pH range for the activation of quartz by calcium as between 9.5 and 12.5 with an optimum value of 11.0, and Hertzog7 has determined the calcium abstraction of iron ores and of Ottawa sand, but otherwise little quantitative data are available. The purpose of the present investigation was to determine those conditions under which dilute solutions of calcium chloride will activate quartz for anionic flotation and to determine the amount of calcium ion adsorbed by quartz. Those variables, the influence of which was primary, such as calcium, sodium, and hydrogen ion concentrations, were studied. Other factors which influenced the results are discussed in the description of the experiments. Three different experimental methods were used to determine the activation of the quartz. The first method was to treat a sample of ground, deslimed quartz with solutions of calcium chloride and sodium hydroxide, and to determine the calcium adsorbed by chemical analysis of the solution. Advantages are that a direct value for the amount of calcium adsorbed is obtained, and introduction of a collector which may affect the adsorption is avoided. The difficulty is to determine the extremely small differences in the calcium concentrations before and after the abstraction. The second method was to determine the activation of the quartz by observing the contact angle obtained on pressing an air bubble against the polished surface of a piece of quartz immersed in a solution of calcium chloride, sodium hydroxide, and sodium oleate. This is the well-known "contact angle" method. The third method was to determine those conditions under which an air bubble will pick up quartz particles immersed in a solution of the desired reagents. Disadvantages common to the sec- ond and third methods are that introduction of a collector is necessary to obtain bubble contact with the mineral; very small quantities of contaminant can give erroneous results; and no information is obtainable concerning the amount of calcium adsorbed. Advantages are that tedious analyses, which at best give approximate results, are avoided, and the conditions, especially for the third method, closely simulate those of actual flotation. Although the most consistent results were obtained with the third method, this paper describes the techniques used and the results obtained from each of the three methods. Distilled water and analytical grade reagents were used throughout except where otherwise stated. Between tests all glass articles were cleaned with a chromic-sulphuric acid mixture and sodium hydroxide. Abstraction Method The raw material for the tests was Ottawa sand sized between 14 and 28 mesh. Batches of 500 g of this sand were dry ground for 1 hr in an Abbe porcelain mill with 2700 g of quartz pebbles. The batches were split down to samples weighing approximately 30 g, and the weight of each sample was adjusted to exactly this value.

Jan 1, 1950

The American Society of Mechanical Engineers extends an invitation to members of the Institute to participate in an exceedingly interesting excursion on Saturday, November 11. Permission has been secured for a visit to the plant of the Electric Boat Co. at New London, Conn. There will be run a special-test on a high-power 8-cylinder, 4-cycle Diesel engine. A large number of submarine and other engines in various stages of construction will be seen, also the boring of torpedo tubes, cylinders and other equipment for submarines. The drafting rooms and foundry mill also be open for inspection. The party will have an opportunity to see at close range the submerging of several submarines, and an attack on a vessel on the surface, an exhibit which is being arranged by courtesy of Rear Admiral A. W. Grant, who is in command of the submarine forces of the United States. The Boston members will leave South Station on train No. 7 at 8.30 A. M. Those from Providence will board this train at 9.36 A. M. The Worcester members will leave on train No. 745 at 8.36 A. M. The New York contingent will leave the Grand Central Terminal at 8.31 A. M. on train No. 8. This train will leave New Haven at 10.30 A. M. Upon arrival at New London, each group will go directly to the Mohican Hotel, where a "get-acquainted" luncheon will be served

Jan 10, 1916