Search Documents

By Henry F. Herley

The New Orient mine, owned and operated by the Chicago, Wilmington & Franklin Coal Co., has caused a great deal of comment and interest because of its unusual features and huge daily production. It is in Franklin County, Illinois, adjacent to the town of West Frankfort. The seam being mined is the Illinois No. 6 which in this locality is 9 to 12 ft. thick and lies approximately 500 ft. below the surface. Without fear of contradiction, it can be said that this is one of the largest coal mines in the world from a daily production standpoint. During 1928, New Orient produced 2,400,000 tons, which amounts to over 10,000 tons each day the mine operated that year. The mine is built for a capacity of 12,000 tons but has actually hoisted over 15,000 tons in one 8-hr, shift. This enormous production can perhaps be better visualized if it is realized that each day's operation depletes over two acres of coal. The general features of this mine have already been fully covered in a paper by George B. Harrington,' President of the Chicago, Wilmington & Franklin Coal Co. In a paper of the nature of Mr. Harrington's, it was unnecessary to stress any particular phase of mining conditions, consequently the ventilation problems were touched upon but lightly. In this paper an attempt has been made to describe some of the problems which have been encountered in providing adequate ventilation for the mine. Ventilating Conditions The acreage allotted to New Orient mine has a length, north and south, of approximately 6 miles, and a width, east and west, of 2 to 4 miles. A number of important considerations caused the hoist shaft, air shaft and surface plant to be located near the southeast corner of the property, instead of near the center, as is usual. During the initial phase of the mine development, the mine was ventilated through these shafts, although there was a full realization that at some future date other shafts would be required.

Jan 1, 1930

L50 Adirondack L1 Alaska L2 Arizona L58 Arkansas L66 Billings Petroleum L3 Black Hills L4 Boston L5 Carlsbad Potash L6 Central Appalachian L60 Central New Mexico L7 Chicago L8 Cleveland L9 Colorado L57 Colorado Plateau L10 Columbia LII Connecticut L55 Dallas L12 Delta L65 Denver Petroleum L13 Detroit L14 East Texas L15 El Paso Metals L71 Evangeline L45 Florida L54 Fort Worth L16 Gulf Coast L61 Hobbs L62 Hugoton L68 Illinois Pet Basin L17 Kansas L18 Lehigh Valley L52 Lou-Ark L47 Mexico L19 Mid-Continent L20 Minnesota L56 Mississippi L21 Montana L22 Nevada L64 Niagara Frontier L23 New York L67 New York Petroleum L25 North Pacific L24 North Texas L26 Ohio Valley L27 Oklahoma City L28 Oregon L63 Panhandle L29 Penn -Anthracite L30 Permian Basin L51 Peru L31 Philadelphia L32 Pittsburgh L33 St Louis L34 San Francisco L59 San Joaquin L35 Southeast L36 Southern Calif L69 Southern Calif Pet L53 South Plains L37 Southwest Texas L48 Southwest Alaska L38 Southwest N Mex L44 Spindletop L39 Tri-State L40 Upper Peninsula L41 Utah L70 Venezuela L42 Washington, D C L43 Wyoming L49 West Central Texas L46 Philippine

Jan 1, 1956

By J. D. Lubahn

Prior tests by Dorn, where the strain rate in a tensile test was suddenly changed, have shown a small, but definite rate-history effect to exist. If this effect is neglected in the calculation of creep behavior from tensile results, an error should occur. This paper shows that this error is smaller than experimental scattering, and may be neglected. DORN1 has found a small but definite rate-history effect in the aluminum alloy 250 at liquid-nitrogen temperature using tensile tests with an abrupt rate change. Such an effect is to be expected from pre-viously known2-6 temperature-history effects, together with general experience that effects produced by changing the strain rate a large amount are simi-

Jan 1, 1959

By AIME AIME

OPPORTUNITY may not be knocking but it, at least, is waiting for you, your family and your friends in that amazing republic south of the Rio Grande. For the first time we are able to publish the official itinerary for the forth-coming Mexico City meeting of 1936. As shown on Page 351, the deluxe special train leaves St. Louis on Thursday. Nov. 5 at 5:30 p.m., returning to St. Louis on Nov. 18 at 8:15 a. m. The schedule provides seven days and six nights in Mexico City with numerous excursions to nearby towns and resorts. The oldest surviving city in' North America is Mexico City, dating back at least to the twelfth century. It was the Aztec capital when Cortez arrived in 1519. The famous cathedral still standing was built on a foundation of sculptured Indian images and the remains of a great Aztec temple. Today it is a city of romance.

Jan 1, 1936

By R. B. Walker, R. Palmer, L. C. Bryner

The purpose of this investigation was to further study some of the factors affecting the air oxidation of sulfide minerals. Data obtained from laboratory studies on the effect of temperature, concentration of iron salts, pH, and other catalysts on the biological and nonbiological oxidation of sulfide minerals are presented. The oxidation of copper sulfide minerals and subsequent leaching of the soluble copper has long been a profitable operation. The chief oxidizing agent is oxygen from the air. This reaction is influenced by a number of different factors such as temperature, light, hydrogen ion concentration, oxidizing agents, and various catalysts. Sullivan1 found that copper sulfide minerals are slowly oxidized by the air and that dilute sulfuric acid and iron (111) increased their solubility. At that time it was not known that bacteria were involved in the oxidation of the sulfide minerals. It has been shown that pyrite, molybdenite, free sulfur, and the copper sulfide minerals found in the waste rock dumps in Bingham Canyon, Utah, are largely oxidized by chemosynthetic autotrophic microorganisms found in the leaching streams.2-6 Similar organisms have been isolated in other mining areas7,8 and from the effluents from coal rnines.9 The following are some of the questions that have arisen regarding the mechanisms of the reactions involved in the leaching process. How dependent is the leaching operation upon the biological reactions? How does the temperature effect the biological and non-biological reactions? How does the concentration of iron (II) and (111) effect the rate of oxidation of copper (II) sulfide? Does the iron act as a catalyst? Does activated carbon act as a catalyst on the oxidation of sulfide minerals? What effect does the hydrogen ion concentration (pH) have on the above reactions? The purpose of this paper is to report the results of laboratory studies on these problems. EXPERIMENTAL The apparatus used in this investigation was an air lift percolator described in our earlier work.' The percolator consisted essentially of an air lift which enabled the leaching solution and microorganisms to pass freely through a suspension of mineral (substrate) in Ottawa sand. The air lift served the additional purpose of maintaining an ample concentration of oxygen and carbon dioxide in the nutrient (leaching) solution. (See Fig. 1.) The percolators were so constructed that they could be immersed in liquid constant temperature baths for temperature studies. The thermostats were controlled to +0.5°C. The reactions were all run in the dark. The percolators were charged with one to three g of mineral, dispersed in 100 g of Ottawa sand and 100 ml of nutrient or leaching solution. The sand was purified to remove traces of iron by digesting with concentrated hydrochloric acid and washng with distilled water until free from chloride. After drying, the sand was ready for use. The compressed air supply was regulated to 5 psi and bubbled through an aerator containing distilled water, which was maintained at the same temperature as the bath used. The air was filtered through cotton plugs to maintain sterile conditions. The tops of the

Jan 1, 1968

By Howard Eavenson

THE low-volatile, or smokeless, coal field of southern West Virginia is in Fayette, Raleigh, Wyoming, Mercer, Summers and McDowell counties, in the extreme southern portion of the state, and extends into the adjacent counties of Tazewell and Buchanan in Virginia. McDowell County is the largest producer, with Fayette and Raleigh counties next. The total area of the field (Fig. 1) is approximately 1600 square miles, or 1,024,000 acres. The percentage of volatile matter in the various seams ranges from 15 to 26 per cent. The upper limit of true low-volatile coal is usually considered to be 23 per cent volatile matter; above this point, the coal usually is classed as medium volatile. This limit will be used in this paper.

Jan 1, 1931

By E. G. Bailey

PLANTS that normally burn coal now able too obtain a substantial increase over their normal supply for their greater power needs, and also additional tonnage for extra storage against the uncertainties of the future. Many plants previously burning oil or gas have already been converted to coal, and those which must yet change to coal will undoubtedly be able to obtain ample tonnage of coal of standard quality at reasonable prices. What a contrast this is to the conditions of 25 years ago, when the shortage of coal and transportation led to prices of $5 to $6 per ton at the mines, and degradation of quality, until the already overburdened railroads were called upon to haul 100,000 ton per day of extra ash alone. This was the result of a runaway market and the loading of gob, slate, and sub-quality coal amounting to an estimated increase in ash of 5 per cent of the total tonnage hauled. The problem of getting increased steam output from inferior coal caused unbelievable reductions in the low normal boiler efficiency of that time and untold labor in firing the hand- and stoker-fed furnaces of that day.

Jan 1, 1942

By Best W. N.

Discussion of the paper of W. N. BEST, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1527 to 1537. WILLIAM A. WILLIAMS, San Francisco, Cal.-I would like to ask whether .Mr. Best ever had any experience with an oil burner that used neither air nor steam? W. N. BEST, New York, N. Y.-Yes. This type is commonly known as the "mechanical spray burner" and uses oil heated under high pressure to above its vaporizing point. These burners are not as efficient as the atomizing type for the following reasons: 1. They produce a round flame which; as with any other type of burner, must pass over a flat surface. A round flame cannot fit a flat surface. 2. They do not evenly distribute the heat, resulting in localized heat. 3. The outlet through which the fuel passes is very small; so all gravities of oil, especially oil containing sand, cannot be burned. 4. Their construction is such that they must be cleaned frequently, as the residuum in the fuel clogs the burner. 5. The oil opening being small, the capacity of each burner is small, so that many burners must be used in a boiler or furnace. (The fewer burners there are, the more accurately they can be regulated.) In marine boilers, these burners are largely used, because they do not require either steam or air for atomization. However, there are other methods by which this objection to other types can be eliminated, such as by the use of a rotary blower and steam turbine engine, the exhaust front the engine passing into the engine condenser, thus obviating loss of water. Mechanical burners are rarely used in shops. I know of but one power plant using them. With mechanical burners, the fuel must be maintained at a high pressure. On board naval vessels, some mechanical burners demand an oil pressure of from 100 to 6001b. It is advisable to reduce the pressure as much as possible, as fractured pipes or fittings are particularly dangerous, for the heated oil escapes as a vapor. In such cases there is liability of an explosion caused by spontaneous combustion.

Jan 12, 1915

[†Aaronson, Alfred E., Oil Producer, Pres., Tuloma Oil Cc Tulsa, Okla. '18 ¦Abad, Leopoldo F., College of Min., Univ. of California Berkeley, Cal. '23 ¦Abadilla, Quirico A., Geol. Dept., Cia. Mexicans de Petroleo "EI Aguila," S. A., Edifico "El Aguila," Esq., Calles Aurora y Comercio, Tampico, Tamps., Mexico. '20 ¦Abbey, Robert Graham, Student, Case School of Applied Science Cleveland, 0. '21 Abbott, Clarence E., Gen'l Supt., Iron Mines Div., Tenn. Coal, Iron & R. R. Co., 1405 Minnesota Ave., Bessemer, Ala. '04] [ ]

Jan 1, 1925

The General Committee met in the Treasury Building at Washington on Oct. 6 and 7. At the first meeting, Cornelius P. Kelley was appointed chairman, and Paul Armitage, secretary. Sub-committees were ap-pointed on Invested Capital, Mine Valuation, and Depletion and De-preciation. On Oct. 7, the reports of these committees were submitted to the General Committee and were referred to the Executive Committee. A motion was carried that the Executive Committee he constituted a permanent committee to continue the work of the Committee, with full power to acid to and increase its membership, that. as thus increased, it should constitute a permanent organization to act- and cooperate with the Treasury Department in matters of mining taxation under the Federal Income and Excess Profits Tax Laws. Thereafter the Executive Com-mittee met and formed a permanent committee as follows: Cornelius F. Kelley, chairman, 42 Broadway, New York City. J. L. Darnell, office of the Commissioner of Internal Revenue, Wash-ington, D. C. J. Parke Channing, 61 Broadway, New York City. Walter Douglas, 99 John St., New York City. R. V. Norris, 542 Second National Bank Bldg., Wilkes-Barre, Pa. J. E. Spurr, Engineering and Mining Journal, 10th Ave., and 36th St., New York City. W. G. Swart, 808 Selwood Bldg., Duluth, Minn. J. P. Finley, 45 Cedar St., New York City. W. A. Williams, Bartlesville, Okla. F. S. Peabody, Peabody Coal Co., McCormick Bldg., Chicago, Ill. Matthew C. Fleming, 71 Broadway, New York City. H. B. Fernald, 54 Wall St., New York City. William G. Mather, Cleveland, Ohio. Walter Fitch, Eureka, Utah. Arthur Thacher, 900 Security Bldg., St. Louis, Mo. John P. Gray, Coeur d'Alene, Idaho. Paul Armitage, secretary, 233 Broadway, New York City.

Jan 12, 1919

F. E. Thompson, Pottstown, Pa.: If Mr. Webster's endeavor to open up the subject of cast-iron should prove as prolific of results as did the discussion on " The Physics of Steel," he must certainly feel richly repaid. His remarks concerning the secretiveness and conservatism of the average foundry-man recall to my mind an instance of a blast-furnace which, for the last year, has been producing much foundry-iron. The manager, believing that much more of his product could be used in the foundry than the foundry-men were will-

Jan 1, 1896

By George Straghan, Ralph Thomas

OIL production in Kentucky in 1941 was 5,191,024 bbl., one barrel less than in the preceding year. The total completions for the state numbered 714, of which 256 were gas Manuscript received at the office of the Institute Feb. 26. 1942. * Geologist, .Kentucky Weal Virginia Gas Co., Ashland, Ky. † Geoloneist. Inland Gas Co.. Ashland. Kv. producers, 220 oil wells, and 227 dry holes. The total number was 95 more than in 1940. No new important oil or gas pools were discovered. The number of dry tests was large, although many of the dry holes could be considered wildcat tests. In western Kentucky, 365 wells were drilled, of which 145 were oil producers,

Jan 1, 1942

By Ralph Thomas, George Straghan

OIL production in Kentucky in 1941 was 5,191,024 bbl., one barrel less than in the preceding year. The total completions for the state numbered 714, of which 256 were gas Manuscript received at the office of the Institute Feb. 26. 1942. * Geologist, .Kentucky Weal Virginia Gas Co., Ashland, Ky. † Geoloneist. Inland Gas Co.. Ashland. Kv. producers, 220 oil wells, and 227 dry holes. The total number was 95 more than in 1940. No new important oil or gas pools were discovered. The number of dry tests was large, although many of the dry holes could be considered wildcat tests. In western Kentucky, 365 wells were drilled, of which 145 were oil producers,

Jan 1, 1942

Page The Cobaltchromium Binary System (paper by A. R. Elsea, A. B. \Yesterman, and G. K. Manning, Met. Tech. June, 1948, Mechanism of Precipitation in a Permanent Magnet Alloy (paper by A. H. Geisler and J. B. Newkirk, Met. Tech. Aug. 1948, Tp 2444)................................................................................................. 300 Some Effects of Applied Stresses on Precipitation Phenomena (~aper by W. L. Finlay and W. R. Hibbard, Jr., Met. Tech. Sept. 1948, Tp 2470)....................................................................................... 301 Diffusion of Carbon in Austenite with a Discontinuity in Composition (paper by L. S. Darken, Met. Tech. Sept. 1948, TP 2443) 304 An Electron Diffraction Study of Oxide Films Formed on Nickelchromium Alloys (paper by J. W. Hickman and E. A. Gul- bramen, Met. Tech. June 1948, Tp 2372)..................................................................... 305 An Electron Diffraction Study of Oxide Films Formed on Copper-nickel Alloys at Elevated Temperatures (paper by J. W. Hickman and E. A. Gulbransen, Met. Tech. June 1948, TP 2391)................................................ 307 Decarburization of Chrome Nickel Alloys by Their Surface Oxides in High Vacua and at Elevated Temperatures (paper by E. A. Gulbransen, W. S. Wysong, and K. Andrew, Met. Tech. Sept. 1948, TP 2438)................................ 307 Fractographic Study of Cast Molybdenum (paper by C. A. Zapffe, F. K. Landgraf and C. 0. Worden, Met. Tech. Aug. 1948, TP 2421)................................................................................................. 308 Effect of Composition on Grain Growth in Aluminum-magnesium Solid Solutions (paper by L. J. Demer and P. A. Beck. Met. Tech. June 1948, TP 2374)............................................................................. 309 Effect of a Dispersed Phase on Grain Growth in Al-Mn Alloys (paper by P. A. Beck, M. L. Holzworth and P. Sperry, Met. Tech. Sept. 1948, TP 2475)................................................................................. 310 Statistical Rate Theory of Metals—Mechanism of Flow and Application to Tensile Properties (paper by J. W. Fredrickson and H. Eyring, Met. Tech. Aug. 1948, TP 2423)............................................................... 315 Nucleation of Slip Bands (paper by J. G. Leschen, R. P. Carreker, and J. H. Hollomon, Met. Tech. Sept. 1948, TP 2476) and.. 318 Transient Plastic Deformation (paper by R. P. Carreker, J. G. Leschen, and J. D. Lubahn, Met. Tech. Sept. 1948, TP 2477).. 318 Plastic Deformation of Large Grained Copper Specimens (paper by W. R. Hibbard, Jr., Met. Tech. Sept. 1948, TP 2469). ... 323 Plastic Flow in Anisotropic Sheet Steel (paper by L. R. Jackson, K. F. Smith, and W. T. Lankford, Met. Tech. Aug. 1948, TP 2440)................................................................................................. 323 The Effect of Thermal-mechanical History on the Strain Hardening of Metals (paper by J. E. Dorn, A. Goldberg, and T. E. Tietz, Met. Tech. Sept. l948, TP 2445)....................................................................... 325 The Room and Elevated Temperature Properties of Some Sand Cast Magnesium-base Alloys Containing Zinc (paper by T. E. Leontis, Met. Tech. June 1948, TP 2371)..............................................................., 327 The Low Temperature Properties of Tin and Tin-lead Alloys (paper by H. S. Kalish and F. J. Dunkerley, Met. Tech. Sept. 1948, TP 2442)............................................................................................335 Thermal and Electrical Properties of Ductile Titanium (paper by E. S. Greiner and W. C. Ellis, Met. Tech. Sept. 1948, TP 2466).................................................................................................... 335 Property Changes during Aging (paper by A. H. Geisler, Met. Tech. Aug. 1948, TP 2436)............................... 337 Factors Affecting the Tensile Notch Sensitivity of Magnesium Alloy Extrusions (paper by I. Cornet, Met. Tech. Aug. 1948, TP 2419)................................................................................................. 338 Effect of Grain Size on Tensile Strength, Elongation and Endurance Limit of Deep Drawing Brass (paper by H. L. Walker and W. J. Craig, Met. Tech. Sept. 1948, TP 2478)............................................................. 339 A Copper-base Alloy Containing Iron as a High-strength, Highconductivity Wire Material (paper by W. Hodge, R. I. Jaffee, J. G. Dunleavy, and H. R. Ogden, Met. Tech. Aug. 1948, TP 2422).............................................. 340 A High Strength-High Conductivity Copper-silver Alloy Wire (paper by W. Hodge, R. I. Jaffee, J. G. Dunleavy, and H. R. Ogden, Mel. Tech. June 1948, TP 2366)...................................................................... 340 The Effect of Chronlium on the Ma Point (paper by J. B. Bassett and E. S. Rowland, Met. Tech. Aug. 1948, TP 2417.... 341 The Kappa Eutectoid Transformation in the Copper-silicon System (paper by W. R. Hibbard, Jr., G. H. Eichelman, Jr., and W. P. Saunders, Met. Tech. Sept. 1948, TP 2441).............................................................. 343 Stabilization of the Ausknite-martensite Transformation (paper by W. R. Harris, Jr. and M. Cohen, Met. Tech. Sept. 1948, TP 2446)................................................................................................ 344 Secondary Hardening of Tempered Martensitic Alloy Steel (paper by W. Crafts and J. L. Lamont. Mel. Tech. Sept. 194,8, TP 2439)................................................................................................. 345

Jan 1, 1950

By Joseph T. Singwald

INTRODUCTION THE purpose of this chapter is to present the diagnostic features (geologic, mineralogic, chemical, and physical) of the principal types of hypogene ore deposits recognized in current genetic classifications, and to classify the ore deposits of the western United States into those types. The genetic divisions used and the criteria determining them are essentially those followed by Lindgren in his Mineral Deposits. Deviations from Lindgren represent either changed conceptions since 1928 (the date of the third edition of Mineral Deposits) due to advance in knowledge or the inevitable differences of opinion between experts in active fields of investigation. Though nineteen economic geologists have been given free hand in presenting their particular topics, there are no fundamental departures in the chapter from the principles set forth by Lindgren. It would be entirely beyond the capacity of a single chapter to give a comprehensive geologic description of all the ore deposits of the western United States. Descriptions of individual deposits have been restricted to those features that are of most diagnostic genetic value. All of the more important deposits receive that much attention. Deposits of lesser economic importance and those inadequately known geologically are treated more briefly or merely cited under what seems to be their proper genetic assignment. The geographic limits of the descriptive matter are the Black Hills and the United States between the Rocky Mountains and the pacific Coast. Capacity of the chapter has made it necessary to impose these geographic limits.

Jan 1, 1933

Division of Geology, State of Tennessee, 401 Seventh Ave, North, Nashville, Tenn. Walter F. Pond, State Geologist A selected list of Bulletins available: Bulletin 1(B), Bibliography of Tennessee geology (1911); 2(A) Outline introduction to mineral resources (1910), 2(D) Marbles (1911); 2(G) Zinc deposits (1910), 16, Red iron ores of east Tennessee (1913), 22, Geology and natural resources of Rutherford County (1920), 24(A) Geology and oil possibilities of parts of Overton, Clay, Pickett and Fentress counties (1920); 24(B) Oil and gas resources of northeastern Sumner County (1920), 26, Mineral resources of Waynesboro Quadrangle (1921); 28, Marble deposits of East Tennessee (1923), 29, Magnetic iron ores of east Tennessee (1923), 31, Zinc deposits of east Tennessee (1923), 33, Tennessee coal fields, 37, Geology and mineral resources of Hardin County, 38, Stratigraphy of the Central Basin (in press), 39, Brown iron ores of the Eastern Highland Rim (in press) From 1911 to 1919, inclusive, volumes were issued annually on The Resources of Tennessee Only a few of the separate papers contained in those volumes are now available Vol. 2 (1911): No 1, Explosions of coal dust in mines, and other papers, No. 4, Lignite and lignitic clays in west Tennessee, and other papers; 5, The growth of knowledge of Tennessee geol¬ogy; 9, The valley and mountain iron ores of east Tennessee, 10, The iron industry of Lawrence and Wayne counties, and other papers; 11, Barite deposits in the Sweetwater district, and other papers, 12, The iron ore deposits in the Tuckalioe district, and another paper Various oil maps (15 to 40 cents each) and traverse maps of counties (25 cents and 31 each) can be had, as well as pertinent U. S topographic maps.

Jan 1, 1933

[ ]

Jan 1, 1942

By W. N. Best

Crude oil attracted attention because of its excellence as a fuel for openhearth furnaoes; for making crucible steel and brass; for melting copper, lead, tin, zinc, nickel, silver, malleable iron, gray iron; and for the production of steam in all sizes and types of boilers. For heating furnaces, mold-drying ovens, core ovens, ore roasters, calciners, hotair furnaces, sand drying, asphalt road work, etc., its superiority over other fuels is due to the fact that the heat is at all times under perfect control, so that a constant temperature may be attained and maintained at the will of the operator. This mcans a maximum amount and uniform quality of work. Crude oil is of two kinds, paraffine base and asphaltum base, and varies from 11 to 46 gravity BaumB. The light-gravity oil does not require heating before use; but oil of less than 20 gravity Baumé should be heated to just below its vaporizing point, in order to reduce its viscosity and to obtain the highest efficiency of combustion. Heavy California oil vaporizes at 230". F., Mexican crude oil at from 175" to 210" F., and Beaumont, Texas, oil at 142" F. Fuel oil vaporizes at 130" F. Scientific Installation Essential The burning of oil is an art based on science, and the "rule of thumb" should never be employed, especially in heating heavy crude oil. Thermometers should be used on both suction and supply pipes so that the fireman or smith will at all times know the temperature of the fuel. The indicators on such thermometers should be large enough to be readily seen by the operator, night or day. It is necessary to have an unvarying pressure of steam or air through the burner, to atomize the fuel. Also, the air used to support combustion should be delivered through a nozzle under the burner at a constant pressure. The oil pressure must not fluctuate; under no eircumstances should it vary more than 1 1b. The oil pump, which should be brass-lined, with the aid of the pulsometer and superheater, will insure a constant

Jan 1, 1916

By S. H. Ash, J. J. Forbes

Probably the newest thing in mining safety, or safety for mines, is the apparent dissatisfaction on the part of the mineral industries, as represented by both management and labor, and the general public of the Nation, with the safety record of the mining industry. This is reflected by published comments and papers in the technical press;l-9 in labor periodicals,10,11 in popular journals and periodicals,l2, 13 and in the daily press; also by discussions of the Safety Committees sponsored by the National Safety Council,9, 14-15 the American Mining Congress,l.l6 the American Institute of Mining and Metallurgical Engineers,2,4 the Mine Inspectors' Institute of Amerthe Coal Mining Institute of America,5 19 the American Standards Association, and others.20.21 Mining safety is a joint problem of management and the individual workman. Safety is not attained and will not be attained solely by laws, decrees, and commands because, if it could be done in this manner, acceptable mining safety would have been achieved long ago by the individual states in our Nation and by the nations abroad. The best safety performance is found at plants where management provides a safe environment for the workers; where supervision is efficient and super- visors, others concerned with promoting safety, and the individual worker know through training, experience, and personal contact the safe and unsafe practices of their field; and where the trained individual worker has become safety-minded by experience, quiet influence, unconscious suggestion, and personal guidance. Despite what may be said to the contrary, progress has been and is being made in mining safety. This is shown in Fig 1 to 4. It is beyond the scope of this paper to give possible reasons for the valleys and peaks in the fatal-injury rates. Some recent factors that appear to be contributing to the improvement in these rates are briefly discussed. Aside from mining equipment, "what's new in mining safety" for some mines has been in effect or was tried by others long ago. A safety pro- gram is a living thing; as such, it must be vitalized and continuously fed with enthusiasm, constructive action, and improvements. Because safety is concerned with human conduct, it is necessary to practice safety at all times; if not, it is soon forgotten, and accidents occur. Mining-safety Records The large employment and production concerned with anthracite contribute much to the mining-safety records of the mineral industry. Approximately 81,000 persons are. employed in this industry having mines concentrated in an area of 480 square miles in northeastern Pennsylvania. Because of the achievement of the anthracite industry in safety during 1948, the other branches of the mineral industry can profit by a study of what has been done to achieve that record. Where one mineral is produced by other large groups having methods of mining that are similar in many respects to the anthracite-mining methods, an achievement in such a large industry is important. Salient factors concerned with safetye in the anthracite industry are: no radical change has occurred in the mining-safety regulations pertaining to anthracite mines. Because anthracite mining is a branch of the coal-mining industry,

Jan 1, 1950

By W. E. Field

In the Coast Mountains approximately 110 miles north of Vancouver, the gold mine of Bralorne- Pioneer Mines Ltd. lies at an elevation of 3500 ft. The deepest or 41 level in the mine is at an elevation of 1400 ft below sea level, and the rock temperature on this level is 122.5°F. The thermal gradient is 1 "F increase in temperature for each 67.5 ft increase in depth. The mine produces between 500 and 600 tons per clay, utilizing an adit two internal shafts, and one service shaft from surface. The Queen shaft, extending from the 26 to the 41 level, IS the deepest, and most production now comes from this area. Stoping in by cut and fill using mill tailing hydraulic backfill.

Jan 12, 1963