Search Documents

By R. C. Buehl, M. B. Royer

A three ton per day blast furnace using blast temperatures up to 2200°F was operated to recover manganese from open-hearth slag and manganiferous iron ore. The spiegel product containing 12 to 24 pct Mn was blown in a basic converter to high manganese oxide slag as described in the paper which follows this one. HE steel industry, which uses over 900,000 short tons of contained manganese yearly, depends on the maintenance of supplies of manganese from foreign sources such as India, Gold Coast, and Union of South Africa. Domestic ores furnish less than 10 pct of the yearly requirements of metallurgical ores and, unfortunately, the United States has no large, or even moderate, grade deposits that could supply a major portion of the requirements for many years. It may be necessary to obtain manganese from low grade materials, even though the cost is appreciably higher than when imported ores are used. An American Iron and Steel Institute questionnaire prepared in 1949 revealed the startling fact that open-hearth slags contained about as much manganese as is imported annually. The quantity of slag produced each year by integrated steel plants (not including cold-melt shops) and the manganese contained in the slag follows: Flush slag, 4,500,000 net tons a year containing 408,000 net tons Mn; tap slag, 7,230,000 net tons a year containing 364,000 net tons Mn; for a total of 772,000 net tons Mn. Some of this slag is returned to blast furnaces but about 75 pct would be available for the recovery of manganese. In several decades, when many of the present sources of high manganese ores have been depleted, open-hearth slag and manganiferous iron ore may become the major source of the manganese required for steel production. In 1948, manganese-ore imports from the U.S.S.R. were 427,000 net tons or 34 pct of the foreign ore. Imports from this source were only 81,000 tons in 1949. It became evident that adequate stockpiles of manganese could not be accumulated for many years. The Bureau of Mines initiated an extensive research program on methods for increasing domestic production of manganese and entered into a cooperative agreement with the American Iron and Steel Institute for recovering manganese from open-hearth slags whereby the Institute provided additional research funds and trained operating personnel. Description of Process and Equipment Numerous pyrometallurgical and hydrometallur-gical processes and combinations of the two can be applied to the recovery of manganese from open-hearth slag and manganiferous iron ore. The process being developed at the Pittsburgh Station of the Bureau of Mines consists of: 1—Reduction of open-hearth slag in a blast furnace to recover the iron and manganese as spiegel-eisen with 12 to 24 pct Mn. 2—Selective oxidation of the manganese from the blast-furnace metal in a basic-lined converter to produce a high manganese slag with up to 60 pct Mn content, which is a synthetic ore for the production of ferromanganese. This process has the advantage over other processes in that the equipment which would be used, such as blast furnaces and converters, has been highly

Jan 1, 1953

By W. C. Hagel, J. H. Westbrook

THERE has been a recent revival of interest in the intermetallic compound AgMg as an experimental material for study of the physical and chemical properties of simple ordered structures. Studies of mechanical behaviors,1-4 diffusion,5,6 and thermo-dynamic properties7'8 have been reported. In several of these studies, heat treatments have been carried out in argon-filled silica capsules at temperatures as high as 750°C with no apparent adverse effects. The present authors were, therefore, startled to discover in the course of some yet unpublished work, that gross melting of near-stoichio-metric AgMg compositions occurred in such samples more than 100 deg below their melting point of about 800°C. This note is to report a brief series of experiments carried out to establish the reason for this behavior. Gross errors in sample composition and failure of furnace temperature controls were quickly eliminated as causes of melting. The first tangible lead came from chemical analysis of an AgMg sample which had melted during treatment at 750°C. A silicon content of 3.3 wt pct was found. Since satisfactory analyses had been obtained on the original as-cast ingot, contamination by diffusion and/or reaction with the fused silica capsule seemed a distinct possibility. A perplexing fact, however, was the apparently capricious incidence of the effect. Not only was it previously unknown, even in the experience of the present authors; but, in the early part of the present study, melting sometimes occurred and sometimes not with specimens treated under constant conditions. Indeed, one sample successfully survived a 750°C heat treatment and yet melted completely during the course of a subsequent anneal in an identical capsule at a lower temperature. To obtain evidence that silicon contamination could lower the melting point to the extent observed, the following experiment was performed. A series of ternary alloys was made up with a stoichiometric AgMg base and containing 0.1, 0.2, 0.4, 1, 2, and 4 wt pct Si. Melting was done in MgO crucibles under a cover of argon gas. After holding 10 to 20 min in the temperature range 850° to 900°C, the alloys were allowed to solidify in the crucible and the temperature during cooling automatically recorded with a Pt/Pt-10 Rh thermocouple. Results from the cooling curves are shown in Fig. 1. Checks within 2 to 5C° were obtained upon repeated melting, cooling, and freezing. The whole series of cooling curves as well as metallographic examination of the melted alloys established that the AgMg rich portion of the AgMg-Si quasibinary is an eutectic-type system. The melting point of AgMg is lowered from approximately 820°C in the pure stoichiometric binary9 to about 710°C in the saturated intermetallic phase. Since second phase was observed in all samples on cooling to room temperature, the solid solubility of AgMg for silicon evidently falls rapidly with decreasing temperature as indicated schematically by the dashed solvus in Fig. 1. It is thus established that a silicon content

Jan 1, 1963

By H. C. Gatos, J. T. A. Pollock, V. Sadagopan

PREVIOUS investigations on the effect of neutron irradiation on the superconducting properties of bulk transition metals indicated that little or no change occurred in poly crystalline disordered materials, particularly if cold-worked prior to irradiation. Only the superconducting properties of ordered intermetal-lic A15 compounds were found to be sensitive to irradiation, and the observed reduction in Tc and increased magnetic hysteresis or critical current densities were attributed to the introduction of flux pinning vacancy clusters and disorder in the lattice. Since the former would also be expected to be present after irradiation in disordered alloys, the general conclusion was that the disordering effect of the irradiation was the primary reason for the changes observed. The present note reports some unusual effects of neutron irradiation on cold worked Nb(Cb)-Ti-V alloys. Specimens with nominal composition as given in Table I were prepared by repeated arc melting, taking the usual precautions, and homogenized at 1000°C for 24 hr prior to a reduction of 15:l by cold rolling. Samples of size 1 by 1 by 25 mm were sliced from the rolled strips. The sarmples chosen for irradiating were sealed in a cadmium tube (wall thickness 1 mm) prior to exposure in a fast neutron flux of 3.7 x 1019 neutrons per sq cm in the swimming pool reactor of Union Carbide Corporation&apos;s Sterling Forest Reactor. During irradiation the temperature of the samples was maintained below 70°C. The irradiated samples were stored at room temperature for approximately 1 year allowing the radiation levels to reach a safe handling value. Tc measurements were made employing a self-inductance coil technique. Jc data at 4.2"Kwere obtained using a four lead resistivity method. The latter measurements were made at the Francis Bitter National Magnet Laboratory by setting the perpendicularly applied field and increasing the direct current through the sample until a potential of about 10-6 v was detected. Tc values for the nonirradiated samples are listed in Table I together with the change in Tc after irradiation. A decrease in Tc of 0.25 or 0.3"K was measured for three of the four samples, the exception being the Nb-30 at. pct V-20 at. pct Ti alloy which showed a decrease of 0.5K. Jc vs applied field data are plotted in Fig. 1 for the Nb-20 at. pct V-30 at. pct Ti alloy. These curves are typical of the four alloys and surprisingly indicate that a degradation occurred in all the samples after irradiation. Hc2 values, obtained by extrapolation to zero current, are 8 to 15 pct lower than those measured for the nonirradiated specimens. The reasons for the degradation of Tc and jc ob-served in the alloys on exposure to neutron irradiation are not immediately apparent. The temperature at which the samples were maintained during bombardment (<70°C) and stored (20°C) make it highly unlikely that any significant change in the dislocation density of the materials through thermally activated migration and annihilation would occur. The explanation must lie in the type of damage produced by the bombardment. McEvoy et a1. reported no change in superconduct-

Jan 1, 1970

By R. Maddin, A. Lawley

Single crystal Mo-Re alloys (99.99+ purity), grown by electron bombardment floating zone heating, were deformed in tension at temperatures from -196° to +200°C. At -196oC, Mo-6 pet Re and Mo-20 pct Re alloys deform by slip on systems of the type (101) [1ll]. Above-78oC, the operative slip system is of the type (112) [111], (101) [1ll], or (211) [1ll], depending upon orientation. Mo-39 pct Re alloys deform by twinning and slip at all test temperatures with a (112) [111] type twinning system. Critical resolved shear stress for slip and twinning is calculated as a function of composition and temperature, and the mechanical properties compared with those of less Pure polycrystalline alloys. HEXAGONAL close-packed rhenium, c/a = 1.615, is highly soluble in molybdenum. The bee molybdenum-rich solid solution extends to approximately 42 at. pet Re* at 2500°C,&apos; Fig. 1. Recent work on polycrystalline alloys has shown conclusively that the addition of rhenium to molybdenum improves both the fabricability and the low-temperature ductility.2"5 Similar behavior is observed for W-Re and Cr-Re alloys.5 Initially, Geach and Hughes2 found that the Mo-30 pct Re alloy could be cold rolled to approximately 90 pct reduction before the onset of cracking. The remarkable effect of the rhenium was later confirmed by Jaffee et al. 3-5 with an optimum condition of maximum strength combined with maximum ductility at the Mo-35 pet composition. At higher rhenium contents, the ductility was severely impaired due apparently to the presence of brittle tetragonal s phase, Fig. 1. In the Mo-35 pet Re alloy, at least 110 ppm (parts per million) oxygen could be tolerated before cold workability was reduced. By comparison, the corresponding tolerance figure in unalloyed molybdenum is ~ 10 ppm. The effect of rhenium was considered in terms of: 1) a reduction in oxygen solubility in the lattice; 2) a redistribution of intergranular oxide from grain boundary films to isolated spheres; and 3) the promotion of twinning as a further mode of plastic deformation. Paradoxically, twinning is often associated with brittle fracture in iron and the silicon irons.6&apos;7 Work to date has been restricted to are-melted and powder metallurgy polycrystalline material of ~ 99.9 pet purity. The present investigation was initiated for the purpose of determining the mode and crystallography of plastic deformation of a series of bee Mo-Re alloy single crystals over a wide temperature range from -196o to +200°C. Using high-purity zone-melted material (~ 99.99 + pet purity), the specific role of rhenium in the molybdenum lattice may be understood more fully since effects due to grain boundaries and oxide redistribution will be absent. At the same time, the study provides a comparison of single and polycrystalline deformation behavior. EXPERIMENTAL TECHNIQUES A) Preparation and Purity of Single Crystals. Alloys in the form of either are-cast and swaged or sintered and ground bar, 0.120 in. diam, were obtained from the Chase Brass and Copper Co. Alloy single crystals ~ 8-in. long were grown from the

Jan 1, 1962

By C. J. Sparks, J. C. Ogle, E. A. Starke

DEFORMATION of cold-rolled fcc metals and alloys produces one or the other of two types of rolling textures, usually referred to as the copper type or the brass type. The pure fcc metals, with the exception of silver, develop the copper-type texture when rolled at room temperature. Silver, brass, and many other alloys develop the brass-type texture. Transition from one texture type to another can also occur. Solute additions to pure copper cause a transition from the copper-type to the brass-type texture.&apos; Varying the deformation temperature also produces texture transitions. Copper rolled at -196°C developed the brass-type texture2 and silver rolled at elevated temperatures, 200°C, developed the copper-type texture.374 The work of Haessner,&apos; Smallman and Green,6 and Hu and coworkers3&apos;4 seems to have established an apparent correlation between the type of rolling texture (and the texture transition) and the stacking-fault probability. Thus materials with low stacking-fault energies are thought to develop the brass-type texture while high stacking-fault energy materials develop the copper-type texture. Mikkola and cohen7 measured by X-ray diffraction techniques the stacking-fault probability, a, in the ordered and disordered fcc alloy Cu3Au. Unexpectedly, ordered specimens showed about twice the stacking-fault probability as the disordered ones. Marcinkowski and Zwe118 also found stacking faults in ordered Cu,Au, but not in the disordered CusAu. More recently, Camanzi and coworkers9 have shown that the intrinsic stacking-fault energy of Cu3Au undergoes a considerable decrease (approximately 100 ergs per sq cm) when passing from the disordered to the ordered phase. In general, deformation reduces order&apos;&apos; but some of our measurements showed that some long-range order still remains in Cu3Au after cold reduction by rolling 80 pct. From the above considerations Cu3Au offers the possibility of studying the texture transition in fcc alloys without varying either the temperature or the composition. If the stacking-fault energy correlation is correct, an initially ordered alloy should develop the brass-type texture during rolling while a disordered alloy should develop the copper-type texture. The present communication describes some initial results of experiments designed to investigate this possibility. The rolling textures of ordered and disordered Cu3Au samples were determined after various amounts of deformation. The ordered sample had an initial long-range-order parameter of S = 1, determined from X-ray diffraction. The grain size of both the ordered and disordered samples was the same, and the initial textures of both were also identical and approximately random. No obvious differences in the deformation textures of the ordered and disordered materials were detected up to 35 pct reduction and the (111) pole figures of Fig. 1 resemble that of pure copper. However, with reduction larger than 35 pct and less than 50 pct, a marked deviation from the copper texture was noted in the ordered material. The newly developed orientation was close to the (110)[i12] ideal orientations re-

Jan 1, 1970

By John M. Kelly

New Mexico produced 38,882,342 bbl. of oil in 1943, and regained seventh place among the oil-producing states. This production was an increase of 6,968,526 bbl., or 21.8 per cent, over the figure for 1942. The maximum per-well allowable on Jan. I, 1943, was 38 bbl. daily and at the end of the year this figure had been increased to 48 bbl. Allocations as set by the New Mexico Oil Conservation Commission closely followed recommendations by the Petroleum Administrator for War and the average daily pipe-line runs were 106,476 bbl., being within 2.2 per cent of these allocations. Production for Lea County was 33,043,925 bbl.; Eddy County, 5,405,-967 bbl.; northwestern New Mexico, 432,070 bbl., and Chaves County, 380 barrels. Drilling activity for New Mexico in 1943 was only 75 per cent of that in 1942, with 255 completions. Of these completions 180 were oil wells, 10 gas wells and 65 dry holes. The ratio of dry holes to producers, more than I to 3, was the greatest in recent years. Of these dry holes, 46 were drilled within the boundaries of proven . areas while 19 were wildcats. Wildcat drilling during 1943 was responsible for the discovery of four new oil fields and one new gas field, as well as three extensions to existing proration areas. At the close of the year the New Mexico Oil Conservation Commission had designated 64 areas as proven for oil and/or gas. The Monument area was again New Mexico&apos;s largest producing oil field, with an annual production of 7,228,855 bbl. Next was Eunice, with 6,461,044 bbl., followed by Vacuum with 4,946,110 bbl. IIobbs, ranking fourth, with 3,799,114 bbl., was the leader in total recovery with an accumulated production of 104,180,53I bbl., or more than 10,000 bbl. per acre to date. Drilling activity in Lea County accounted for completion of 67 oil wells, 2 gas wells and 24 dry holes. One of these oil wells was the discovery well of a new area and three extended proven areas. The most active drilling campaign in the county was again in the Maljamar area, where 18 oil wells were completed. The Maljamar Cooperative Repressuring Agreement affected 141 producing wells, and operations were a decided success, more than 85 per cent of the gas produced being returned to formation. The new oil field for Lea County was designated as the San Simon area although boundaries have not been established to date. Discovery well for this area was the Skelly Oil Company&apos;s State U. No. I, in theNE. NE. K of sec. 5, T.22 S.,R.ssE. This well was drilled to a total depth of 4183 ft. and plugged back to 4138 ft. after encountering bottom-hole water. Initial production was 124 bbl. per day on the pump. This oil is 37.4&apos; gravity and has a sulphur content of I per cent. Productian is from Yates sand of Permian age. The Lynn area of southern Lea cbunty was extended 145 miles to the northwest

Jan 1, 1944

By John M. Kelly

New Mexico produced 38,882,342 bbl. of oil in 1943, and regained seventh place among the oil-producing states. This production was an increase of 6,968,526 bbl., or 21.8 per cent, over the figure for 1942. The maximum per-well allowable on Jan. I, 1943, was 38 bbl. daily and at the end of the year this figure had been increased to 48 bbl. Allocations as set by the New Mexico Oil Conservation Commission closely followed recommendations by the Petroleum Administrator for War and the average daily pipe-line runs were 106,476 bbl., being within 2.2 per cent of these allocations. Production for Lea County was 33,043,925 bbl.; Eddy County, 5,405,-967 bbl.; northwestern New Mexico, 432,070 bbl., and Chaves County, 380 barrels. Drilling activity for New Mexico in 1943 was only 75 per cent of that in 1942, with 255 completions. Of these completions 180 were oil wells, 10 gas wells and 65 dry holes. The ratio of dry holes to producers, more than I to 3, was the greatest in recent years. Of these dry holes, 46 were drilled within the boundaries of proven . areas while 19 were wildcats. Wildcat drilling during 1943 was responsible for the discovery of four new oil fields and one new gas field, as well as three extensions to existing proration areas. At the close of the year the New Mexico Oil Conservation Commission had designated 64 areas as proven for oil and/or gas. The Monument area was again New Mexico&apos;s largest producing oil field, with an annual production of 7,228,855 bbl. Next was Eunice, with 6,461,044 bbl., followed by Vacuum with 4,946,110 bbl. IIobbs, ranking fourth, with 3,799,114 bbl., was the leader in total recovery with an accumulated production of 104,180,53I bbl., or more than 10,000 bbl. per acre to date. Drilling activity in Lea County accounted for completion of 67 oil wells, 2 gas wells and 24 dry holes. One of these oil wells was the discovery well of a new area and three extended proven areas. The most active drilling campaign in the county was again in the Maljamar area, where 18 oil wells were completed. The Maljamar Cooperative Repressuring Agreement affected 141 producing wells, and operations were a decided success, more than 85 per cent of the gas produced being returned to formation. The new oil field for Lea County was designated as the San Simon area although boundaries have not been established to date. Discovery well for this area was the Skelly Oil Company&apos;s State U. No. I, in theNE. NE. K of sec. 5, T.22 S.,R.ssE. This well was drilled to a total depth of 4183 ft. and plugged back to 4138 ft. after encountering bottom-hole water. Initial production was 124 bbl. per day on the pump. This oil is 37.4&apos; gravity and has a sulphur content of I per cent. Productian is from Yates sand of Permian age. The Lynn area of southern Lea cbunty was extended 145 miles to the northwest

Jan 1, 1944

By J. M. Oblak, R. F. Hehemann, R. H. Goodenow

STUDIES of surface relief and growth kinetics have lead to the concept that widmanstatten ferrite along with upper and lower bainite constitute a continuous series of decomposition products.1-4 Current models4 propose that these products form as plates with a coherent or semicoherent leading edge which propagates at a rate controlled by diffusion of carbon into the surrounding austenite. There are, however, important crystallographic and morphological differences between these products—particularly between upper and lower bainite. For example, upper bainite appears to exhibit a (11lIy orientation habit, whereas lower bainite develops with a more irrational habit near {2251y.5-7 Many of the morphological features of these decomposition products are not yet well-documented. Recent studiess have demonstrated that low-carbon martensites form as sheets of closely spaced needles on {lllly planes while higher-carbon martensites form as plates with {225}? or other orientation habits. The similarity in the crystallography of these two modifications of martensite with upper and lower bainite is striking. Therefore, a study of the morphology of bainite in a series of hypoeutec-toid alloy steels has been initiated to explore these relationships further. The question of immediate interest is whether upper and lower bainite form as plates or needles. A two-surface (approximately perpendicular) metallographic method was employed to study the morphology of bainite in a variety of low and medium alloy steels. Compositions of these steels have been reported elewhere. The behavior of 4340 and 4370 was typical and will be described here. Austenitizing treatments involved 20 min at 2350°F for 4340 and at 2000°F for 4370. Isothermal transformation was conducted in molten-salt baths. Upper bainite was produced at 925°F in the 4340 steel and lower bainite at 575°F in 4370 with transformation times adjusted to produce 10 to 15 pct of the decomposition product. Many of the morphological features of upper bainite have been catalogued in the recent literature.&apos;&apos; The two principal variants observed in the present investigation are illustrated in Fig. l(a). One form appears as long, thin plates or needles and the other as small, frequently irregularly shaped particles. Both variants may occur as isolated forms but more frequently appear in groups as demonstrated in Fig. l(a). Two-surface analysis reveals that these two variants constitute different sections through a single morphological form. To demonstrate this, a number of sections perpendicular to the plane of Fig. l(a) were prepared at various positions along the length of the elongated particles. A section taken at position 1 in Fig. l(a) is presented in Fig. l(b). Here, the dark line represents the edge of the sample and the left-hand portion of this photomicrograph is that from the surface perpendicular to the original plane of polish. Since it was necessary to repolish the original surface after each sectioning, the shape of the bainite particles on this surface, right hand side of Fig. l(b), changes with each sectioning. The disappearance of plate A, Fig. l(a), in Fig. l(b) emphasizes the small cross section of these structures. The group of particles in the lower left-hand

Jan 1, 1964

By D. H. Polonis, J. G. Parr

IN a recent paper on titanium-rich Ti-Fe alloys,&apos; the hardness of quenched powder specimens was given, together with the amounts of martensitic a they contained. The values disagreed in two respects with previous determinations that Worner² made on lump specimens: 1—Some martensitic a&apos; is formed in powder specimens of alloys containing up to 12 atomic pct Fe. On the other hand, Worner reports that, although his results on quenched lumps are not conclusive, alloys containing more than about 4 pct Fe "appear to consist of retained ß&apos;&apos; although they "may not be strictly unaltered solid solutions." 2—According to Worner, quenched lump specimens show a maximum hardness at a composition about 3.5 pct Fe. Earlier -experiments by the authors showed a maximum hardness of martensitic alloys in powder form at 10 pct Fe. Accordingly, more experiments have been conducted in order to confirm these differences and to determine with more accuracy the minimum composition of quenched lump specimens that consist entirely of retained ß. Lump samples?x?x1/20 in. were quenched from 1000°C in helium and, on the whole, showed similar hardness values to the specimens that Worner water-quenched from 950°C. The hardness curve the authors obtained shows a more pronounced peak, but in other respects it is very similar to Worner&apos;s curve (Fig. 1). While it was possible to make fairly reliable measurements of the percentage of martensitic a in quenched powders (by Geiger spectrometer), the solid samples allowed only approximate estimates to be made from visual observation of line intensities on film. Retained ? begins to appear in quenched lumps containing 0.2 pct Fe; at 2.2 pct Fe there are approximately equal quantities of ß and a&apos;; in a 4.7 pct Fe alloy only a trace of a&apos; appears. These results are represented as a curve on Fig. 1. The hardness and constitution of powder samples were verified by repeating both types of quenching experiment described in the earlier paper.&apos; Identical results were obtained by the two methods, and they agreed with the figures published previously (Fig. 1). The appearance of the martensitic structure under the microscope is shown in Figs. 2 and 3. The mar-tensite needles are coarser in the lump; otherwise the structures are similar. Three conclusions are made at this juncture: 1— The properties of quenched lumps reported by Worner are confirmed, on the whole. The differences between them and the properties of powders are probably due to an effect of specimen size. Differences of behavior in various sizes of specimen have been observed previously in martensite reactions in Fe-Mn alloys3 and in Cu-A1 alloys. 2—The maximum hardness of both quenched lumps and quenched powders appears at a composition where martensite formation has all but ceased. In this respect, powders and lumps behave similarly. 3—Martensitic a&apos; has essentially the same microscopic appearance both in powders and lumps. Acknowledgment This work is part of a program sponsored by the Defegce Research Board of Canada, Project No. 425.

Jan 1, 1956

By J. P. Heller, H. B. Bradley, A. S. Odeh

A potentiometric model technique is presented for determining the areal sweep efficiency of a five-spot well pattern, at and beyond breakthrough. A sharp interface between displaced and displacing fluids is assumed. Although the prototype svstem is referred to as a waterflood operation, obvious changes in the notation and computations will adapt the results to other displacement processes. The results of the study include the following. 1. Areal sweep efficiencies for a five-spot well pattern, at and beyond breakthrough, for mobility ratios (displacing to displaced fluid) of 4:1, 2:1, 1:1 and 1:4. 2. Extension of potentiometric analysis to the investigation of the areal sweep efficiency beyond breakthrough in a five-spot pattern by the application of conformal mapping and conductive-solid models. 3. The use of layers of conductive fabric in representing mobility ratio changes in potentiometric models. 4. The development of a probe mechanism for probing conductive solids. The results obtained by conductive-cloth models agree with earlier areal sweep efficiencies at breakthrough obtained by Aronofsky and Ramey 1 on the potentiometric analyzer using electrolytic-tank models. Results beyond breakthrough differ from those obtained by the X-Ray Shadowgraph technique. Data from this study show that, for mobility ratios greater than one, water cut rises rapidly as fluid is produced after breakthrough. However, for mobility ratios smaller than one, a large increase in area swept resulted with only a small increase in water cut. INTRODUCTION In calculating reservoir performance of waterflood-ing operations and other fluid-injection programs, it is necesssary to estimate the areal sweep efficiency * before and after injected-fluid breakthrough into production wells. Influence of mobility ratio on oil-production history, before and after breakthrough for a five-spot well pattern, has been studied by X-Ray Shadowgraph techniques 2-5 and by gelatin models.6 In none of these investigations was the transition zone controlled experimentally. Steady-state anaiog techniques assume that a vertical and discrete interface exists between the displacing and displaced phase. Thus, when using a potentiometric analysis, it is assumed that no transition zone exists. To determine the areal sweep efficiency beyond breakthrough for a five-spot well pattern using the potentiometric analyzer, four principal problems had to be resolved. These were the following. 1. The laborious method of representing changes in mobility ratio in electrolytic tanks by means of contoured wooden blocks. 2. Vapcrization of the electrolyte solution during the study causing concentration changes and, thereby, variable conductivity. 3. The scale-limitation problem 7 that is accentuated by abrupt eiectrolyte depth changes. 4. A wellbore geometry problem. EXPERIhlENTAL EQUIPMENT AND PROCEDURES CONDUCTIVE-SOLID MODEL The theory, equipment and procedural techniques of the electrolytic-tank potentiometric model have been treaced excellently by Lee8 and by Muskat.9 By the use of a conductive solid to represent the fluid conductivity of the porous media, the need for contouring wooden blocks to represent mobility ratio was eliminated. It was found that a carbon-black coated fabric, Uskon D-16,** could be employed as a fairly uniform conductive media. This material, when stacked in appropriate layers and pressed together, can be used to represent changes in mo-

By A. S. Emanuel

A correlation has been developed for calculating the phase behavior of, gas-condensate systems at reservoir conditions. The correlation is based on the principle of corresponding states and has been coded for an IBM 7094. Experimental K-values were determined for several gas-condensate systems at reservoir conditions to evaluate various semi-empirical parameters of the correlation. The approximate range of application of the correlation is 150 to 300F and 1,500 to 6,000 psi. INTRODUCTION The rapid development of digital computers during the past several years has made feasible the calculation of hydrocarbon phase behavior by methods based on rigorous thermodynamic principles. Good correlationsl have been developed for low to moderate pressures, but these techniques have not yet been extended successfully to reservoir fluids at high pressures. Consequently, the determination of phase behavior of oil and gas systems at reservoir conditions is still based almost entirely on generalized data correlations or on experimental studies of the fluid in question. While these methods have been used successfully many times, they do have inherent limitations that restrict their applicability. Generalized correlations, such as the NGShlA K-charts, are limited to the range of pressure, temperature and components for which the data were determined. The accuracy of these correlations is often questionable because the effect of total system composition is not well defined. Experimental studies offer a reliable method for determining phase behavior, but usually the studies are costly and time consuming. Recently, Leland and co-workers presented a new approach to calculating phase behavior from the principles of corresponding states.6-8 Corresponding states methods determine the thermodynamics properties of a given system by comparison with a reference substance whose properties are known. The accuracy of this approach depends on close chemical and structural similarity between the reference substance and the system in question and between components within the system itself. For high accuracy, it is usually necessary to correct for chemical and structural dissimilarities. In principle, however, the corresponding states method should be no less accurate at high pressures than at low pressures, provided reference substance properties are known. This paper describes an empirical modification of the basic correlation proposed by Leland, et al.6 for the specific purpose of calculating the phase behavior of gas-condensate fluids at reservoir conditions. The modified correlation, which has been programmed for an IBM 7094, may be used for either approximate or precise determination of fluid behavior depending on the amount of analytical and, experimental data available for the system. BASIC THEORY The basic theory of the corresponding states phase equilibria correlation was first published by Leland, Chappelear and Gamson.6 Subsequently, Leland, Chappelear and Leach published methods for improving the accuracy of the original theory.7-9 The aim of the correlation is to calculate the K-value of each component of a given system as a function of pressure, temperature, and over-all composition, where Once the K-values are known, the phase behavior may be determined directly by an appropriate flash calculation. The basic equation for calculating component K-values was taken from the work of Joffe. 4 For any component i of a mixture, the K-value is given by

Jan 1, 1969

By D. C. Shelton

This paper discusses the metallurgical testing procedures and their applications at the laboratories and mills of Pima Mining Co. The author shows, using discussions and case histories, that routine sampling and evaluation of daily and monthly data can be as valuable as thorough laboratory investigations and mill test work. A great deal of valuable information can be made available this way. This paper discusses laboratory and mill metal-lurgical testing procedures and their applications at Pima Mining Co., located about 25 miles southwest of Tuscon, Ariz. The Company, incorporated in 1951 (the year the orebody was found) in California to operate the Pima mine, is jointly owned by Cyprus Mines Corp., Utah Contruction and Mining Co., and Union Oil Co. Milling started in December 1956. The main Pima orebody is a contact metamorphic vein of copper-bearing hornfels with an average dip of 45° to the south with an east-west strike. The hanging and footwalls are quartzitic pyroclastics (arkosite) containing some sulfides. Barren igneous intrusions are also present. Conglomerates and alluvial wash cover the deposit to a depth averaging about 200 ft. The principal copper mineral is chal-copyrite. Native copper, chalcocite, and minor amounts of chrysocolla and other copper minerals are also present, together with sphalerite and some molybdenite. Generally, it has been noted that the ratio of chalcocite to chalcopyrite is higher in the lower grade ores, while as the grade increases, there are only minor amounts of chalcocite. Open pit mining is employed at Pima, using both trucks and an inclined skiphoist system. A detailed description of Pima Mining Co. operations was presented by Spaulding et all. More recently another orebody to the north and east of the present pit has been discovered and will be placed in operation within a few years. This ore is of a porphyritic rather than a lode nature since values are disseminated in both igneous and metamor- phosed sedimentary rocks. The new orebody is expected to be harder and cleaner than the present deposit. The views expressed in this article are those of the author and do not necessarily reflect those of Pima Mining Co. nor of the profession in general. PlMA MILL The following outline of milling practice is presented to furnish a background for later chapters of this report wherein specific problems will be detailed and analyzed. Run of mine ore is crushed in three stages, using conventional equipment to 85% minus 1/2-in. for feed to two 10 x l6-ft rod mills operating in open circuit. Each rod mill discharge is split between two 10% x 13-ft ball mills in closed circuit with three 20-in. cyclones. In addition, a 7 x 12-ft ball mill with one 20-in. cyclone receives part of the discharge from one of the rod mills. This equipment was manufactured by Allis Chalmers and Equipment Engineers. The cyclone overflows are combined, sampled and, after joining the regrind cyclone overflow, are distributed into 12 10-cell Fagergren 66-in. flotation machines. The primary rougher concentrate produced

Jan 1, 1965

By E. Stamboliadis

Dithiophosphates are reaction products of phosphorous pentasulfide with various organic compounds such as phenols, alcohols, mercaptans, dioalcohols, amines, and nitrides. The products with alcohols are commercially known as "aerofloats" and these are investigated in this presentation. It appears that the formation of insoluble metal dithio phosphates is responsible for their collecting properties with minerals." In this aspect they are very similar to xanthates.3 The solubility of metal dithiophosphates depends on the number of carbon atoms in the organic chain of the corresponding alcohol. An empirical mathematical model is presented here. It allows one to predict the number of carbon atoms necessary to ensure that a certain metal dithiophosphate will form at a selected pH value of the water solution. The Nature of Dithiophosphates Dithiophosphoric acid is the product of the reaction of phosphorus pentasulfide with an alcohol, as shown in the following equation: [P2S3 + 4 ROH - 2 (RO)2 PS2H + H2S (1)] where R stands for a hydrocarbon chain. The acid so produced can be neutralized by a base to produce the corresponding salt as shown in the following: [(RO), PS2H + NH- (RO)2 PS, NH,. (2)] In this aspect dithiophosphates are similar to xanthates, the only difference being the substitution of the tetravalent carbon atom in the xanthate polar group by a pentavalent phosphorus atom in the dithiophosphate group. This difference implies at least two characteristics: (1) that there are two hydrocarbon chains associated with the polar group so that an increase in the number of carbons of the single chain is expected to have a pronounced effect on the flotation properties, and (2) that the bond between the sulfur and the central atom is stronger than in the xanthate group. This probably leads to a decrease in both the polarizability of the electronic cloud of the sulfur and the interaction with cations.3 However, what is lost in the dithiophosphates by having a weak polar group can be gained by an increase in the number of carbons as will be seen later. Taking into account the size of the atoms involved in a dithiophosphate molecule, as listed in Table 1, It is possible to draw an approximate diagram of its structure as shown in [Fig. 1]. It is assumed here that the length of the single hydrocarbon chain is equal to that of the corresponding alcohol. Preparation and Purification Acid dithiophosphates can be prepared, as previously mentioned, in accordance with Eq. 1. The rate of this reaction is too slow at room temperature and can be improved by increasing the temperature to about 60° or 80°C7 or by evacuating the system. In our investigation evacuation was performed by a water aspiration pump. The dithiophosphoric acid so produced is liquid and dissolves in the alcohol. At the end of the reaction the product is filtered from the remaining P2S3; and dissolved in petroleum ether. By blowing anhydrous ammonia gas into the ether phase the ammonium salt forms as a white precipitate and can be sepa-

Jan 1, 1977

By W. M. Phillips

Processing kaolin clays from the sedimentary deposits of Georgia and South Carolina is described in this article. While the major processing steps are touched on briefly, emphasis is given to the dewater-ing of the clay-water slurries (slips) formed in the processing of kaolin clays. The dewatering steps discussed include gravity settling, centrifugal dewatering, vacuum filtration and thermal drying. Particular attention is given to vacuum filtration and the variables affecting filtration of these kaolin clays. Kaolin consists essentially of the mineral kaolinite, which is a hydrated aluminum silicate (Al2O3 . 2SiO,). Commercial deposits of kaolin occur in several areas of the U. S., but approximately 90% of the kaolin produced in this country comes from Georgia and South Carolina. These deposits are of sedimentary nature and occur in a geological fall line in the Tuscaloosa formation at elevations between 300 and 450 ft above sea level. Over two million tons of kaolin clays are used by industry in the U. S. each year. A big percentage of this tonnage is used in the paper industry for coatings in making glossy and high quality grades of printing papers. In addition, large tonnages are used as pigments; as fillers for rubber, plastic and fertilizers; and in ceramics. Properties of kaolin that make it widely used in the above applications are its particle size fineness, natural whiteness, chemical stability and non-abrasiveness. In addition to these desirable properties, it is relatively inexpensive. The finer coating grades of clays range in price from $15 to $28 per ton while the coarser filler grades sell within a range of $7 to $13.50 per ton. Pure kaolin particles are small hexagonal flat platelets. Above the 2-p size, the particles usually consist of stacks of plates, while below the 2-p particle size they occur as individual flat, hexagonal plates. Since these individual platelet particles provide the most desirable coating and flow characteristics, major importance is given to particle size fractions of 2 p and smaller. Generally, coating grade clays are those with all particles smaller than 15 p and at least 70% of the particles less than 2p. These coating grades also have 50% or more of the particles smaller than 1 µ in size. The extremely fine grades of coating clay currently being produced approach the range of 100% smaller than 2p. The filler grades of kaolin have 100% of the particles passing 325 mesh but have less than 70% of their particles below the 2-p range. Fig. 1 is a schematic representation of the major processing steps involved in preparing kaolin clays for marketing. MINING All kaolin mining is open pit. The ratio of overburden to clay will average 3:1, but this ratio can, of course, be much higher depending upon the grade of the clay and the size of the deposit. Most of the commercially mineable deposits occur from 20 to 120 ft below the ground surface. Both draglines and pans are used in removing the overburden and mining the clay deposit itself. After mining, the most common method of transporting the clay to the processing plant is by blunging or re pulp-

Jan 1, 1963

By S. F. Reiter, You-Chao Liu, W. R. Hibbard

Cyril Stanley Smith in his classic 1948 Institute of Metals Lecture&apos; noted in the case of annealing twins that: "It is well known that approximately the same number of twins per grain and the same general geometry are maintained in large grains as in small ones, a fact that certainly suggests a mechanism such as the above where boundaries and twins grow proportionately together. If this view is correct, a spherical grain should have no mechanism for keeping its twins." Such a constancy of twins per grain would be of particular interest as a tool for the study of the origin of annealing twins. It has been proposed by Mathewson2 and later by Barrett3 that in face-centered cubic metals slip occurs in the {111} Plane by <112> shears which combine in pairs to produce the macroscopically observed <110> movement. This proposal is schematically inviting since <112> slip permits the atoms of one plane to move along the interatomic valleys of its neighbor rather than up the hills across the atom sites. There is strong experimental evidence? that annealing twins result from the growth of nuclei in the form of "twin faults" produced by single <112> shears. It is possible that more twin faults would form at low deformation temperatures than at high ones, because the more rigid lattice may increase the tendency to "freeze" the twin faults and prevent their dissipation in slip. This is suggested by (1) the greater resistance to slip at low temperatures and (2) greater tendency toward mechanical type twinning at low temperatures (a summary of these factors is presented by Seigle and Brick5). These considerations would suggest the following: a. Constant twin/grain ratio for specimens deformed constant amounts at a constant temperature, but annealed at various temperatures above the recrystalliza-tion temperature. b. Larger twin/grain ratios for re-crystallized specimens previously deformed constant amounts at lower temperatures. The purpose of this investigation is to test these considerations. One half in. rods of phosphorous deoxidized electrolytic copper and 70-30 alpha brass (68.36 pct Cu, 0.005 pct Pb, 0.01 pct Fe, 31.62 pct Zn remainder) were rolled to a thickness of 0.350 in., milled to specimens 0.350 X 0.437 X 2 in., and annealed at 700°C to an average grain size of 0.065 and 0.090 mm, respectively. These specimens of each metal were then rolled 50 pct reduction in thickness and annealed one hour under conditions which were all combinations of the following: Rolling Annealing Temperatures. Temperatures. °C °C -70 400 25 500 200 600 Standard metallographic techniques&apos; were used to prepare specimens. By the method of lineal analysis7 using a minimum of ten samples of fifty grains each for each specimen, the ratios of twins* per total grains, twins per twinned grain, twin families* per total grains and twins per twin family were determined. Recrystallized grain size was determined by A.S.T.M. comparison methods.8 All observations were made on the rolling plane. The results are tabulated in Table 1.

Jan 1, 1950

By Nicholas J. Grant, Italo S. Servi

THE creep and stress rupture properties of three grades of aluminum have been reported in a previous paper.&apos; It was found that the stress coefficient of the creep rate and of the rupture time changes at the transition from low temperature-type to high temperature-type deformation. The transition corresponds to the equicohesion for grains and grain boundaries. In order to support the conclusions obtained from the examination of creep and stress rupture data, the deformed specimens were observed metallographically and a few special tests were conducted. The results of these qualitative observations are given in the present paper. Experimental Procedure and Results Table I gives the types of aluminum specimens.&apos; The creep and stress rupture tests were conducted in simple tension at constant stress. Further details on the experimental techniques have been given.&apos; The test bars were electropolished in a perchloric-acetic mixture before testing and were observed after testing without any further preparation unless otherwise specified. Observations of specimen cross-sections were made after electrolytic polishing and etching. The samples were extended along a direction parallel to the longer side of the micrographs of Figs. 12 through 27. The log-log plots of stress vs. minimum creep rate for the three grades of aluminum appear in Figs. 1 and 2. The reference numbers on each curve help relate the photographs to the conditions of testing, indicating where high temperature-type deformation and failure prevailed and where low temperature behavior prevailed. Deformation of Single Crystals at Very High Temperature: An annealed, high purity aluminum specimen was slightly strained at one end and re-annealed. A large single crystal was formed at the strained end of the specimen during re-annealing; the other end remained polycrystalline (see Fig. 3). A stress of 50 psi was applied to the cold specimen to avoid loading at 1100°F. The temperature was then raised to 1100°F, kept at 1100°F for 3 hr, and lowered again to room temperature. Fig. 4 shows the appearance of the specimen after testing. The single crystal deformed by gliding along parallel planes, while the polycrystalline part deformed mainly by grain boundary flow. Some grain growth occurred in the polycrystalline part. Another high purity specimen, which had two large single crystals at the two ends and a polycrystalline zone in the middle portion, was tested at 1000 °F under a stress of 100 psi. The appearance of the sample after test is shown in Fig. 5. Even though considerable slip occurred in the single crystals, the fracture occurred in the weaker polycrystalline portion. Evidence of Grain Boundary Migration during Creep Testing: A high purity, coarse grained specimen, which had a large crystal in the middle portion (see Fig. 6) was tested at 700°F under a constant stress of 175 psi for 30 hr. The appearance of the specimen after testing (Fig. 7) indicates that the large crystal deformed by gliding along parallel planes, while the rest of the specimen deformed mainly by grain boundary flow. Microscopic examination showed clear evidence of grain boundary flow and grain boundary migration, an example of

Jan 1, 1952

By R. S. Hoch, Roy A. Bobo

Maintenance of desirable plastic flow properties of weighted drilling muds may be greatly simplified by use of centrifugal classification to control the drilled solids content. The new application of a decanting type centrifuge to separate and reject the low density solids from the weighting material results in a drilling mud of greatly improved quality with lower values of yield and rigidity. Its practicality and economy has been proven in field operation. The degree of separation of light and heavy solids is not limited by the machine, but by the particle size distribution of the solids in the mud. Removal of the low density component of drilling mud that makes chemical treatment necessary permits a marked reduction in chemicals. The main uses of the centrifugal process are the treatment of muds while drilling, the reclaiming of discorded muds, cleaning up of workover muds, and the reduction in lime content of mud for completion. INTRODUCTION Drilling mud in any circulatory system is made viscous and difficult to pump by gradual accumulation of drilled solids which pass through the shale shaker and are continually reground. In a weighted mud containing a large proportion of barite by volume, the amount of drilled solids that may be tolerated is greatly reduced. Much effort has been expended to control by chemical treatment the effects of such solids. Though chemical treatment is quite effective, the time eventually comes at deeper depths after enough drilled solids have entered the system when a portion of the mud must be discarded and replaced with water and more weighting material. Once begun, this process is generally continued at frequent intervals with resultant high maintenance costs. At the termination of drilling, mud highly contaminated with light solids and spent chemicals is poorly suited for completion operations.&apos; It is likewise limited in utility for other drilling operations. This investigation was conducted for the primary purpose of determining an acceptable mechanical means of removing the lightweight solids from weighted drilling muds in order to maintain viscosity at a minimum. A decanting type of centrifuge was selected from the various possible methods of mechanical separation. The centrifugal process has been employed in this country for this purpose in central mud reclamation systems in California in earlier years. It also was used for treatment of weighted muds on the Gulf Coast.&apos; In more recent years only sporadic attempts have been made to employ it in the field on weighted muds. DISCUSSION OF PROCESS Selection of Apparatus Two factors favor mechanical procedure for the separation and removal of drilled solids or clays from the mud circulatory system. First, the greater specific gravity, 4.1 to 4.3, of the barite would promote more rapid settling than the clays whose specific gravity range is from 2.5 to 2.7. Second, the relative coarseness of the barite particles also facilitate faster settling of this phase. A decanting type of centrifuge was preferred for this process over other possible methods for these reasons: 1. Requires no costly additives or excess dilution. 2. Centrifugal force affords greatly accelerated separation as compared to gravity.

Jan 1, 1955

By Rex E. Cheek, Donald E. Menzie

The fluid mapper, a model relatively new to the petroleum industry, was used to study the effect of various mobility ratios on the areal sweepout efficiency for two typical spacing patterns. The experiments indicated the areal sweepout for the five-spot pattern varied from 51.8 per cent at a mobility ratio of 0.093 to 89.1 per cent for a ratio of 24.4. In the direct line-drive pattern, the areal sweepout varied from 58.7 per cent at a mobility ratio of 0.089 to 92.0 per cent at a ratio of 24.8. The fluid mapper may prove useful to determine quickly the effective areal sweepout for any well spacing. INTRODUCTION The effect of the mobility ratio on the areal sweepout efficiency during primary depletion of a water drive reservoir and during secondary recovery operations has recently become more widely recognized The mobility ratio, M, is defined as: _ kjp (displaced fluid) k/u (displacing fluid) where k = effective permeability u = viscosity When the displacing fluid is miscible with the displaced fluid, the permeabilities are equal and the mobility ratio may be expressed as a ratio of viscosities: u (displacing fluid) u (displaced fluid) The mathematical analysis for calculating the areal sweepout efficiency with mobility ratio other than unity is quite tedious.5,11 An experimental method by using a potentiometric model2 in a step-wise manner and in using an X-ray shadowgraph model3,12 with continuous fluid flow has been published. Several types of models have been used to study oil and gas reservoir performance. These models may be classified as physical, electrolytic, potentiometric, X-ray shadowgraph, and fluid mapper. The X-ray shadowgraph and fluid mapper are models relatively new to petroleum engineering and have not been used extensively for specific applications. The theory of the fluid mapper indicates it may be adapted to a study of areal sweepout efficiencies for various mobility ratios as well as other complex problems in petroleum engineering. The use of the model and results obtained when using displacing and displaced fluids of equal densities but different viscosities are discussed. FLUID MAPPER DEVELOPMENT H. S. Hele-ShawV eveloped a fluid mapper model based on the hydrodynamic theory. This theory is that in the steady flow of a viscous fluid between horizontal parallel plates spaced a very small distance apart, the effect of viscous shear is of such magnitude in the vertical plane that the motion in the horizontal plane is practically undisbrted streamline flow. Techniques developed by Hele-Shaw were not expanded and no additional developments in fluid mapper models were forthcoming until A. D. Moore, University of Michigan, published a series of papers starting in 1949, which describe the construction of a flexible and inexpensive model&apos;h nd the fluid mapper technique for the solution of certain problems.&apos; The essential components of the fluid mapper as developed by Moore are::.ln 1. A base slab. made of dental stone (calcium sulphate and water). which is shaped to represent the prototype. 2. Plate glass slightly larger than the slab and spaced

Jan 1, 1956

By C. H. Samans, G. F. Tisinai, J. K. Stanley

The times at which the first detectable amount of a phase forms at temperatures between 900° and 1800°F were determined. Both X-ray diffraction and metallography were used to detect a in highly strained filings; metallography alone to detect it in annealed bulk samples of six different types of stainless steels. The a phase was found to form in accordance with the C-type reaction curve in both austenitic and ferritic alloys. In filings of types 304, 347, and 446, a formed in a few hours, and in types 316, 309, and 310, it formed in a matter of minutes at temperatures corresponding to the knee of the C-curve. Only in the bulk type 309 steel, after 500 hr, and in the bulk type 310 steel, after as short a time as 25 hr at temperature, was n detected; in both instances at approximately the same optimum temperature as in the filings. The annealing temperature affected a phase nucleation only for the filings of type 304 and 347 steels, and for the bulk samples of type 309 and 310 steels. KNOWLEDGE of both the rate of nucleation and the rate of growth of the new phase is required for a complete description of metallurgical rate phenomena. However, data on the time for nucleation alone may frequently be useful in evaluating the tendency of commercial stainlcss steels to form s under various conditions. Very little correlated information of this type is available in the literature. Shortsleeve and Nicholson&apos; indicate that s forms in ferritic 24, 27 and 30 pet Cr steels according to a C-type of reaction curve, and Emmanuel&apos;s&apos; data for austenitic type 310 steel also suggest this type of solid state reaction. In addition, significant, though fragmentary, information has been given by Binder, Dulis and Smith,4 Payson and Savage,.; Guarneri, Miller, and Vawter,8 rerichs and Clark,7 Wilder,5 Lismer, Pryce, and Andrews,&apos; Smith, Dulis, and Link,10 Dulis, Smith, and Houston," and Henry, Cordovi, and Fischer." The bearing of these data on this work is covered in the discussion. The purpose of this paper is to present such correlated data on s formation in AISI type 304 (18 pct Cr-8 pet Ni), 347 (18 pet Cr-10 pet Ni-Cb), 316 (18 pet Cr-12 pet Ni-2 pet Mo), 309 (25 pet Cr-12 pet Ni), 310 (25 pet Cr-20 pet Ni), and 446 (27 pet Cr) stainless steels. Materials and Test Methods X-ray diffraction and metallographic methods were used to determine the first appearance of the s phase in cold worked filings and in annealed bulk samples of seven steels, under various combinations of time and temperature. The rate of growth of the s particles was not determined. Commercial heats of six AISI steels and a low carbon laboratory experimental heat containing about 28 pet Cr were studied. Analyses are given in Table I. Because cold work greatly accelerates the nucleation of s particles, the relative rates of s nucleation in mechanically strained samples, i.e., filings through 120 mesh, were determined for direct comparison with those in annealed bulk alloys of the same composition.

Jan 1, 1957

By Nicholas J. Grant, Robert H. Kane, Bill C. Geissen

The platinum-rich section of the Ta-Pt Phase diagram was worked out by metallographic and X-ray techniques, using twenty alloys; solidus temperatures and solid solubilities were determined. Besides s phase, four intermediate stoi-chiometric phases were found: TaPt (high-temperatzrre phase, structure unknown); TaPt2 (ortho-rhomhic, new type); a TaPt3 (orthorhombic, TiCu3 type); ß TaPf3 (monoclinic, new type). TaPt2 and TaPt3 melt congmentlv; two eutectic, two beritec-tic, and one eutectoid reactions occur in the inuestigated range. THE Ta-Pt system was examined as part of a study of the phase diagrams and the intermediate phases of niobium and tantalum with Group VIII transition metals. Since the main scope of this work was the relation among the ordered close-packed phases occurring in the concentration range from AB to AB3 (A = Nb, Ta; B = Pd, Pt, and so forth), only the platinum-rich side of the diagram was worked out thoroughly, while spot checks were made to determine the approximate outline of the tantalum-rich portion. The system has not been thoroughly treated in the literature; Greenfield and Beck1 in their survey of refractory metal intermediate phases found a o phase between -18 and 37 at. pct Pt which coexists at higher platinum concentrations with an unidentified intermediate phase. Browning2 worked on the range between 55 and 100 at. pct Pt; however, this preliminary study did not cover temperatures >1500°C, and included no conclusive crystallo-graphic data. More recently, a study of the platinum-rich section of the Ta-Pt system has been carried out by Ray,3 while Hartley, Parsons, and steedly4 have studied the tantalum-rich section. The crystal structures of TaPt2, a TaPt3, ß TaPt3, and others have been reported in abstracted form by Giessen and Grant.5 EXPERIMENTAL METHODS The methods of alloy preparation and processing and of the metallographic and X-ray procedures follow very closely those described by Ritter, Giessen, and rant&apos; for other refractory metal-noble metal systems, and will not be repeated except where significant differences exist. Starting materials were: tantalum rod of 99.95 pct purity, supplied by National Research Corp., and platinum sponge 99.9 pct, supplied by The International Nickel Co. An oxygen analysis of the tantalum rod showed 30 ppm O; other impurities were C, N, Si, Nb, Mo, none of these exceeding 50 ppm, and 100 ppm W. Homogeneous buttons were readily prepared as follows: ingots of 5 g were weighed and arc-melted under welding grade argon, followed by two remelts after inverting the button. Between 40 and 100 at. pct Pt, weight losses during the first melt rarely exceeded 0.1 pct, in which case the alloy was rejected, and were nil on subsequent remelts. Since the vapor pressure of platinum far exceeds that of tantalum, the small evaporation loss could be assumed to consist of platinum; therefore, a corresponding amount of platinum was added on the second melt. Since it was confirmed on pure tantalum samples that no weight gain through oxygen or impurity pickup occurs (see Ref. 71, it could be assumed that the uncertainty in the composition did not exceed ±0.1 at. pct for the range 40 to 100 at. pct Pt. For the four control melts from 0 to 40 at. pct Pt, an error of ±0.5 at. pct was calculated. Microscopic examination of the whole buttons after melting showed no inhomogeneity other than local coring. This was eliminated by a homogenization heat treatment. A total of twenty-three alloys were prepared. Heat treatments were carried out in a tantalum

Jan 1, 1965