Search Documents

By Paul Riches

LR Process Expert is a cost-efficient process automation system for all types of long rolling mills, including, rod, bar, section, rail, reversing mills, and flat blocks. The system performs a wide range of tasks for optimized operation – from suggesting pass schedules to calculating and downloading optimized mill settings according to the availability of rolls. LR Process Expert also monitors and collects data from the raw material stage through to the finished product. It delivers valuable mill reports to the operator staff and management so they can easily assess a plant’s performance and optimize production. Defined Key Performance Indicators (KPIs) help to assess a plant’s performance; this system is not limited to one plant but can enable plant-toplant performance at corporate level.

Aug 16, 2017

By Michael Windhager, Karl H. Ziehenberger

ULTIMA® are high performance, centrifugal cast, double poured (CC duplex) work rolls. This paper describes the principle of the ULTIMA® roll concept and its wide range of usability. The ULTIMA® concept provides a solution for rod and bar mills to increase performance and output, even under harsh rolling conditions. The main focus is on highly loaded mill stands that require both high wear resistance and resistance against thermal fatigue, like pre-dog bone, dog bone, slitter. Specific case studies of quite different mill configurations and rolled product mix prove the positive impact on production yield, mill and roll shop operations, and profitability in terms of TCO (total cost of ownership).

Oct 1, 2019

By Alberto Tremea

In this period a great attention is put on roll cost and the differences in roll behavior in very few situations move the existing balances. Among many variables that are taken into account to evaluate the roll there is the consumption which is normally calculated according to the tonnage rolled. In this work there is a review of some approaches that are used to evaluate the roll efficiency together a description of a new method to make this. The main purpose of this calculation method is to help the comparison of roll results used in different mills. There is the need to have a clear and univocal reference when it’s time to think about innovative products. At now there are available roll grades with excellent technological properties but it’s necessary to have the right tools for a careful evaluation of roll behavior to take a good decision.

Jul 30, 2018

By Mirko Jurkovic, Thomas Hueper, Jens Kempken

The high competition scenario pushes the steel producers business. Zero defect requirements from customers force the operators for additional efforts in process control and quality management. PQA® has been developed as an advanced process and quality management assurance solution. It is focusing on the analysis of process data, equipment information, inline quality measurement devices and trend analysis. The paper describes the structure of the advanced process and quality management assurance solution PQA®; it gives insights on the expert know-how, process and quality evaluation and points out the benefits like cost reduction, improvement yield and customer satisfaction increase.

Oct 1, 2019

By Andrea Zanon

Slitting processes have been used for many years to increase the productivity of smaller diameter deformed bars, without making major investments in the rolling mill. This technology is used mainly for the production of reinforcing bars (7-20 mm diameter), but successful applications exist also for round bar production. The multi-slitting process enables to produce up to 5 bars starting from one billet, thus increasing the productivity of the smaller products. Danieli Morgårdshammar, world leader in the supply of rolling mills for long products, has been a front-runner in slitting technology since its first applications and has recently developed, first in the world, the technology to produce 5X8mm rebar. This process has been recently applied in BRSM steel, a company based in Bangladesh which is a worldwide benchmark for slitting technology performances. This paper presents the necessary modifications which need to be considered when developing a 5-strand slitting project (and multi-strand slitting projects in general), as well as the results obtained at BSRM Steel when the process was implemented in 2016, the first rolling mill in the world rolling 5X8 mm slit rebars.

Oct 30, 2017

By Peter Fajfa, Heinz Palkowski, Jakob Kraner, Matjaž Godec

The study of asymmetric rolling on the AA 5454 aluminium alloy plates was carried out. The plates were taken directly from the industrial hot rolled sheet. They were cold rolled on the laboratory mill with different rotation speed of the upper and the lower work roller with the strains around 33 % and 44 %. To get closer to the industrial conditions the maximal dimensions of the rolled plates for laboratory rolling mill and the special industrial lubricant were used. After deformation the plates were annealed to the soft condition. This research was focused on all possible effects of asymmetric rolling: The reduction of rolling force, the increase of strain at same set roll gap, bending of workpiece, finer microstructure, more heterogeneous textures and as a consequence of that better mechanical properties. The asymmetric rolling with favourable mechanisms in the deformation zone has created the material with the homogeneous hardness in the cross section and with lower anisotropy, which is crucial for improvement of formability properties of aluminium work hardened alloys and to get closer to properties of steels. In the presented paper the general impact and different effects of speed difference of rollers was investigated on cold rolled aluminium alloy. Obtained and analysed results explain the function of asymmetry in rolling process and the options to implement the asymmetric rolling in industrial plant.

Oct 1, 2019

By Sébastien Gérardin

Developed for more than 30 years, continuously improved, cored wire is nowadays a reliable solution for the improvement of sustainability, safety, health and doing quality and cost saving. Cored wire allows the addition of ferroalloys and treatment of liquid steel, especially concerning the calcium treatment. Amongst all the processes in secondary metallurgy, calcium treatment is certainly the most critical one before casting. Besides the traditional CaSi and CaFe wires, new types of wire have been designed for becoming the new reference in calcium treatment. PapCal (calcium insulated wire) and HDx (high density calcium wire) are a very versatile range of products. Indeed, according to the steelmaking process parameters (steel grade, treatment temperature, ladle size, calcium content targeted in tundish and even injection conditions), their technical specifications may be adapted in order to optimize the calcium treatment as high as possible.

Aug 16, 2017

By Jörg Schwelberger

Government regulations around the world concerning environmental care are becoming more stringent, also including regulations and restrictions of depositing and use of dust, sludge and slag generated in the iron and steelmaking process. With this scenario, by-products such as iron containing dust, sludge, oxide fines, mill scales and slag, become a valuable resource and recycling may be a profitable activity within a plant. Up to ten percent in mass of the total steel output of dust, sludge and mill scale by-product materials and more than 40% of slag by product are generated within an integrated steel plant with an iron content ranging from 50% to 65% for fines and up to 25% for BOF-slag. Slags are being widely recycled and used in the cement industry, as is the case for BF slag, and in the construction industry in the case of BOF slags and EAF slags. However, value of BOF unmodified slag is typically low and environmental regulations limit the usage of the unmodified BOF slag. This paper describes innovative solutions for recycling of fines using cold briquetting technology and the modification and granulation of slag from steelmaking that increase the value of the by-product and yield a marketable product.

Aug 16, 2017

By Rafael Abreu Fraga, Carlos Noberto Paula da Silva, Emanuelle Garcia Reis, Daniel Bojikian Matsubara

Since 2016 Gerdau Ouro Branco has been producing steel plates of various qualities and grades. However, it was not until 2018 that the first plates produced by accelerated cooling process were made available for external testing, in this case for large diameter UOE pipes manufacturing. Recent line pipe and OCTG specifications are showing that the oil and gas market still consumes regular API grades, such as X60, X65 and X70, however with increasing wall thicknesses, reaching values up to 1.5 inches. These specifications also demand longitudinal and transverse tensile guarantees and drop weight tear tests in temperatures as low as -40°C. Projects with these types of mechanical properties present process requirements as challenging as those necessary for higher API grades in lower thicknesses. This paper shows the steel design concepts and rolling routes for achieving the necessary properties for X70 steel plates in 28.15 mm. The microstructural features were also investigated and associated with the production process and the tensile and toughness results. Finally, challenges such as tensile anisotropy and DWTT abnormal fracture are presented.

Oct 1, 2019

By Francisco Morganti

Weight reduction is the main target of all carmakers, which results in a continuous development of new steel grades. Latest 3rdgeneration advanced high-strength steel grades (AHSS) are complex materials with special chemical compositions and multiphase microstructures. The pickling, annealing and galvanizing processes of these grades aresomewhatdifferent due to the changed chemical compositions and microstructures. Therefore, these innovative steel grades place new demands on the plant technology of pickling, annealing and galvanizing lines. The most significant challenges for the pickling process are sludge occurrence during pickling, varying pickling times, weld ability of the materials, changed visual appearance and required high surface qualities. The most important topic concerning annealing line is a precisely controlled and very flexible heating and cooling process in the furnace.One of the new requirements in galvanizing linesis the prevention of surface faults caused by bare spots, which can occur since these materials feature a higher content of alloying elements like silicon or manganese. Prevention is possible with the special pre-oxidation technologies.Due to the higher strength of the material also the mechanical equipment has to be designed differently in these lines. This paper describes the influences of the changed chemical composition and material characteristics of modern steel grades on the pickling, annealing and galvanizing process and gives an overview about the technical solutions.

Oct 30, 2017

By Jovanir Francisqueto, José Fagundes, Nayara Neves Coutinho, Marco Túlio Costa

The purpose of this project is to increase the visibility of which will be daily produced on the hot strip mill (HSM). The forecast was performed through the implementation of an automated tool for weekly HSM production planning. The project was started with the definition of the weekly planning process, through the determination of the main business objectives, like as: priorities of service (customers and delivery date), definition of HSM’s rules and restrictions of operating resources. Using a sophisticated mathematical model, through the computational simulation is possible the experimentation of various production scenarios, allowing the visualization of volumes by type of sequence, clients / priorities, mix to be produced, cylinder change quantity forecast, better forecasting of the productivity of the HSM, consumption of utilities, within others. Main benefits: sequencing which production orders should be produced, reducing unforeseen stops due lack of material, improving the quality of the stock which allows the reduction of the aging of slabs in the slabyard and the vision of customer services. Computational simulation as a weekly planning tool achieve, with other benefits, to present alternatives for better decision making.

Oct 6, 2019

By Arnaldo Forgas Júnior

Three techniques for ferrite quantification were applied in a duplex stainless steel UNS S31803 solution treated at three different temperatures, 1000, 1100 and 1200°C, in order to verify their compliance with the results from ThermoCalc® prediction. It is verified that only austenite and ferrite phases are present in the samples and that an increasing in solution treatment temperature led to the increase of the volume fraction of ferrite. It is also observed that quantitative stereology technique shows absolute values closer to ThermoCalc® predictions. On the other hand, measurements by ferritoscope and XRD show significant deviations, probably due to texturing effect imposed by the rolling process.

Aug 16, 2017

By Alexandre Rizek Schultz

Silat, Siderúrgica Latino-americana, selected Russula as the main engineering contractor for their 700,000 tpy Greenfield steel plant dedicated to long and flat steel production. The project is currently under construction in the district Guararu in Caucaia in the metropolitan region of Fortaleza. The project will be developed in two phases. First phase: 600,000 tons per year rebar mill and 60,000 tpy steel mesh line; Second phase: 700,000 tpy melt shop (90 ton/hr EAF and 4 strand continuous caster for billets up to 180 mm x 180 mm).

Aug 16, 2017

By Uazir Bezerra de Oliveira, Günther Staudinger, Michael Skorianz, Edo Engel

Oct 1, 2019

By L. Martins Demuner, D. Burzic, V. Cunha Aranda, F. L. Lourenço, G. Romeu Trindade dos Santos, F. Ramstorfer

For many years, Dynamic Soft Reduction has been regarded as a proper method in improving internal quality of slabs. Even though processes models improved significantly over the past years, the efficiency of Soft Reduction was always limited by the discretization error, which inherently exists if segment rollers cannot be positioned individually. The recently developed SRD segment type allows for an individual roller positioning within the mushy zone by avoiding any discretization deviation from the optimal gap. This paper provides a detailed technological overview of the SRD segments as well as operational results at their very first implementation at Ternium Brazil.

Oct 1, 2019

By Henara Lillian Costa

This paper aims to investigate the effects of a possible incorporation of ethanol to the lubricant during engine use on friction and lubricant film thickness, by adding small amounts of ethanol to Group I base (with and without an organic friction modifier) and to formulated oils. Film thickness was measured using ultrathin film interferometry. Friction tests were carried out using a mini-traction machine to obtain Stribeck curves. The film thickness measurements showed that in the region of low speeds, where the elastohydrodynamic film is very thin and therefore boundary lubrication may prevail, the addition of ethanol produced some boundary film, which was not present for the base oils. For the base oil with an organic friction modifier, the presence of ethanol increased the thickness of the low friction boundary film. For the formulated oil, the addition of ethanol reduced film thickness in all lubrication regimes. The friction tests showed some friction reduction due to addition of ethanol to the base oil, in particular at low speeds. For the formulated oil, the addition of ethanol reduced friction at high speeds, which was associated to a reduction in the viscosity of the lubricant, but at low speeds, the presence of ethanol reduced the formation of a boundary layer, increasing friction. For the base oil containing an organic friction modifier, the presence of ethanol increased the range of speeds for which low boundary friction occurred.

Jul 31, 2018

By Jean-François Stumper, Mario Moser, Mark Kruessmann, Volker Langer, Daniel Bastos Martins Cruz, Claude Meisch

The latest generation of probes and casthouse machines provide a wealth of data that has not been available a few years ago. The evaluation of this data gives direct feedback to improve the blast furnace efficiency, the equipment maintenance and design and it allows the early detection of critical or deviating process situations. A stable operation with lower operation and maintenance costs are the final customer benefits.

Oct 1, 2019

By Wagner Viana Bielefeldt, Vinicius Cardoso da Rocha, Augusto Lachini Pereira, Antônio Cezar Faria Vilela

A minor change in the chemical composition and temperature affects the slag viscosity, which has a great extent of the physical properties in regarding refining slags. Optimizing those parameters may affect the steel cleanliness. The viscosity measurement process is considered expensive, so the cost-effectiveness does not favor the measures at high-temperatures. Alternatively, it is possible to apply mathematical models or thermodynamic softwares to obtain viscosities for a given range of chemical composition and temperature of slags. The present work contemplates a validation of the experimental data, collected in the literature, with a calculated data and proposes an accurate representation of iso-viscosity curves applied for secondary steelmaking slags, covering the composition ranges: 0–100 wt.% CaO, 0–80 wt.% SiO2, 0–77 wt.% Al2O3 and 0–15 wt.% MgO (CSAM) system at 1500ºC. The viscosity representation fields include fully liquid and a partially liquid slags in the CSAM system and the viscosities were calculated using the FactSage 7.2 (for Liquid Phase) and the Roscoe-Einstein equation (for Phase mixture) for a total of 5976 slags. The preliminary results indicated that there is a great convergence between the calculated and experimental viscosities data, promoting an efficient approximation of the iso-viscosity curves for the CSAM slag system in the high-temperatures.

Nov 1, 2019

By Enrique Francisco Somolinos Garcia-Morales

In this paper we will discuss the benefits of a very innovative way of introducing MgO in the blast furnace operation through the sinter, using mini lumps of dunite. By changing the traditional way of using an MgO bearing material in fines form (particle smaller than 5 mm), most of the MgO inserted material behaves as inert during the sintering process, with the effect of having the following parameters (among others) improved: productivity at the sintering bed, permeability inside the blast furnace, energy consumption, stability of the operation.

Aug 1, 2018

By Breno Totti Maia

In these hard days for Brazil steel market, all steel shops want to achieve the same goal, work with: productivity, low costs and high performance. In this scenario the Slagless® technology (which is applied into BOF converter) was important to reach these targets. After use has been reduced the number of times of tip exchange in more than 04 times. Was reduced too, the time to remove lance skulls. Lance keeps clean during all his life with record number of the life 1255 .Blow keep stable due strong measure control at the nozzles and more improvements are planning.

Oct 30, 2017