Search Documents

IN the irregularly shaped ore-bodies of the North Mount Lyell mine by overhead stoping, the method of filling the is a special feature.The situation of the mine two miles from the smelter and mill at an devation of 1000 ft. above the latter, precluded the economical use of granulated furnace or the mill tailings, even if these materials were as suitable for the purpose as the rock nowquarried at North Lyell methods at Mount Lyell have already been described in Proceedings of the Institute.*The breaking the ore in large dome-shaped stopes is still the rule, but the slope or "rill" is much flatter now than formerly. Owing the greater fluidity of the filling now in use, it is sometimes necessary to resort to square-sets, both at the ground floor and above, the roofs and walls are generally enough to permit stoping without timber, except for ground and occasional stacks on the rills.Sufficient area of ground floor has been beaten out to start overhead stoping, the dome back is partly formed, with its apex a rise which connects with the mullock-pass reticulation.(Sce 1 showing this reticulation in diagrammatic form.)

Jan 1, 1927

By J. T. McCartney

The Bureau of Mines has developed an automated reflectance scanning microscope system, primarily for determination of volume proportions, size distribution, and mode of association of the physical (petrographic) components of coals. The process, which is potentially more rapid and objective and less tedious than a visual microscopic procedure, involves magnetic tape recording of several millions of reflectance readings on micro-meter sized areas of polished coal surface and computer analysis and interpretation of some characteristics of the coal components. The system was tested in a study of pyrite distribution in steam coals. The application was essentially successful, but defects in polished pyrite surface characteristics and problems in adequate sampling prevented completely satisfactory results. Pyrite con-tent and coal-pyrite particle association could be determined nearly as well as by visual microscopy, but size distribution data were less acceptable.

Jan 1, 1969

By B. K. Shibler, W. G. Sandell, G. M. Potter, H. D. Snedden

"INTRODUCTION During the course of the investigation of the occurrence of manganese deposits in the western United States, examining 'engineers of the Bureau of Mines collected samples from seven manganese properties in Grand and beery Counties, Utah. These were supplemented by five samples submitted by property owners. Since all of the ores were too low-grade for use in producing ferromanganese for steel manufacture, some means of beneficiation was required to produce marketable concentrates, and metallurgical studies were made on each of the samples.Most of the ores Investigated are similar in one respect: At least part of the 'manganese oxide areas contains minute inclusions of gangue. This occurrence materially enhances the complexity of the ore, partly by .increasing the complexity of mineral association, but largely through making manganese-quartz liberation more difficult. In such ores, there is a marked tendency for the manganese minerals to be retained as shells or coatings on the surfaces of quartz particles when crushed. Particles of this type represent considerable loss of manganese in tailing, if gravity-concentration methods are employed, or tend to' float, thus carrying an appreciable quantity of gangue into the concentrate, if treated by flotation.Plus 48-percent manganese sinters were made from some of the ores tested, but, in general, intimate association of manganese minerals with silica limited the degree of beneficiation attainable."

Dec 1, 1947

By C A. Feebrey, R A. Duncan

The Ebor Volcano in north eastern New South Wales is an eroded example of a central-type intraplate volcanic-intrusive complex. It is of Miocene age (19 - 20 Ma) and has similarities to other central-type volcanoes in eastern Australia which may represent manifestations of sub-lithospheric hotspot activity. Thick lava flows are exposed around the Great Escarpment and are dominated by a tholeiitic basaltic suite, ranging from ol-tholeiite to qz-tholeiite to icelandite with ages of 19.2 - 19.6 Ma. On its western edge, the tholeiitic lava suite probably overlies remnants of basanite flows belonging to the Eocene (~48 Ma) Doughboy province, but elsewhere, minor alkaline basaltic lavas may be coeval with the tholeiitic suite. Several felsic bodies were emplaced into the volcano at ~19.0 - 19.2 Ma and include subalkaline and peralkaline types. The Crescent Complex is a Miocene-age, strongly differentiated mafic to felsic intrusion in basement rocks and centrally located in pre-erosion reconstructions of the Ebor Volcano. It is interpreted to be a major feeder for the tholeiitic lavas based on age and composition. Evolution of the dominant tholeiitic suite proceeded from a parental ol-tholeiite magma, through qz-tholeiite, icelandite and small volumes of felsic rocks by fractionation of plagioclase, olivine, clinopyroxene and titanomagnetite, accompanied by enrichmentof SiO2, SFeOlMgO, alkalies and HFSE.

Jan 1, 1995

By D. Song

In this paper, the differential equations governing the mass transport and the electrochemical reaction in a cathode catalyst layer of polymer electrolyte membrane fuel cells are solved based on the polynomial series expansion method. Explicit expressions for the polarization curve as well as for the distributions of oxygen, current density and overpotential are obtained when a quadratic, cubic or quartic polynomial is employed to approximate the oxygen concentration distribution. These kinds of explicit solutions are desirable for MEA design and diagnosis purposes. The comparison between the conventional numerical approach and the explicit solution approach proposed here shows that satisfactory accuracy can be reached by the first four terms of the polynomial series. The effect of the catalyst layer thickness on the accuracy of the obtained explicit polynomial solutions is also discussed.

Jan 1, 2005

By Jan M. Mutmansky

Simulation is a general term which commonly appears in the technical literature and which can have different meanings to different people. One interesting definition (9)* applicable in an engineering context is the following: "Simulation is the use of a model to study a problem." In most cases, the model referred to in the above definition is a simulation model constructed in a computer language and implemented on a computer in order to solve the problem under consideration. The application of computer simulation models to the study of problems in materials handling and earthmoving has been successful in the past. Generally speaking, this method has been used where the system to be studied has many variables and where the ability to predict the outcome of the system under different sets of conditions is difficult. The prime reason for using such a model is to evaluate the numerous likely ways of operating any particular system without the necessity of actually conducting full-scale field tests. The simulation model presented here is such an application made to the process of tunneling and, in particular, to the process of tunneling with a boring-type tunneling device. At first glance, the process of tunneling may not appear to be particularly complex and susceptible to study by a computer model. However, a close analysis of the tunneling process will reveal that it is rather complicated as a result of limitations placed upon the system by restricted space in the tunnel, geologic variations along the tunnel

Jan 1, 1972

By W. R. Reed, G. W. Luxbacher

As directed by the MINER act of 2006, the NIOSH Office of Mine Health & Safety Research (OMSHR) has annually awarded contracts to enhance mine safety and health. OMSHR has a history of research that focuses on both respirable coal mine dust and respirable crystalline silica (or quartz) dust, and contracts have been awarded since 2010 in support of our intramural research efforts. In 2018, a National Academies of Science consensus study report recommended expansion of respirable dust research. As a result, beginning in 2018 through 2021, eighteen contracts were awarded focusing on this area. These contracts can be grouped in three topic areas: characterization of coal/dust, development of real time monitors, and improvement of respirable dust controls. This paper summarizes the outcomes of completed contracts and the progress of current contracts.

Mar 2, 2022

By Frank E. Chase

Clay veins, also referred to as clay elastic dikes, have been responsible for numerous underground injuries and fatalities. These hazardous structures are also responsible for increased production costs during all phases of mining. For these reasons, the Bureau of Nines has investigated the physical characteristics of and roof instability problems associated with clay veins in order to make support and other mining recommendations. In addition the occurrence and origins of clay veins were examined to determine whether or not the structures could be projected into unmined portions of the coalbed. This investigation included portions of the Arkoma, Illinois, Northern Appalachian, Southern Appalachian, and Uarrior Coal Basins. Virtually a11 clay veins observed or documented occurred in the Illinois and Northern Appalachian Basins. Observed clay veins ranged in sire from 1 inch to 16 feet In cross-section and were found under shale, siltstone, sandstone, and limestone roof rock. Individual clay veins were predominantly composed of claystone; however, limestone. siltstone. and sandstone infilled clay veins do occur. Clay vein formation has been associated with the infilling of fissures which result from compressive, tensile, or shear ground failures. These gaping fissures were propagated by compactional processes and/or tectonic stresses active during and subsequent to coal iff cation. Associated fault, fracture, and slickenside planes commonly parallel clay veins and disrupt the lateral continuity of the immediate and, sometimes, main roof. When clay veins parallel or subparallel the direction of face advance the roof is segmented into cantilever beams causing unstable conditions. Therefore, the strata on either side of the clay vein must be bolted and strapped together to form a beam.

Jan 1, 1984

By Willem Le Roux

1.1 Section 47(1) of the Mine Health and Safety Act, 29 of 1996 (?the MHSA?) establishes a Mine Health and Safety Inspectorate which is administered by the Chief Inspector of Mines. The Mine Health and Safety Inspectorate is part of the Department of Mineral Resources. The Chief Inspector is appointed by the Minister of Mineral Resources (see section 48(1) of the MHSA). 1.2 The Chief Inspector must, amongst other things, ensure that the provisions of the MHSA are complied with and enforced, and that all the duties imposed upon the Chief Inspector and the other Inspectors of Mines in terms of the MHSA and any other law are performed. The Chief Inspector of Mines must appoint Principal Inspectors of Mines and Inspectors of Mines to assist him/her to discharge his/her duties (see section 49(1)(a) and (c) of the MHSA).

Jan 1, 2011

By Armin W. Stuedlein, Youssef Bougataya

Early stage design of driven piles primarily relies on static analysis based on one or a combination of total and effective stress approaches, the latter known as the method to estimate axial capacity. A database of 85 piles driven in the Puget Sound Lowland region and monitored at End of Driving (EOD) and Beginning of Restrike (BOR) was compiled along with capacities estimated using the CAPWAP procedure. Established soil profiles based on borings with standard penetration tests (SPT), cone penetration tests, and geologic maps were matched with their corresponding unit shaft resistance profiles from the CAPWAP procedure and resulted in more than 1,200 observations. In this study, eight new models were developed to predict the coefficients at EOD and BOR, based on the corresponding USCS categorization. Each coefficient model is formulated using a three-parameter exponential function, calibrated to capture the profile of coefficients with depth. These models could benefit the designer by providing them with a simple, empirical model that accounts for soil type and setup in a smooth, continuous function with depth. A parallel analysis was performed to assess the accuracy and variability of the formulated prediction models to facilitate implementation in load and resistance factor design (LRFD). INTRODUCTION The design of the axial capacity of driven piles during the planning stages of a project is typically based on a static analysis approach. The goals of this approach are to predict the components of capacity, consisting of the shaft and toe bearing resistances, and to assess project concept feasibility and preliminary lengths. In most cases, this analysis is based on empirically-developed methods, such as the total stress method, also known as the method (Tomlinson 1987) or the effective stress method known as the method (Esrig and Kirby 1979; Fellenius 1991). Many other methods, such as those based on in-situ test results exist and rely on correlations of blow counts from the standard penetration test (SPT), and cone tip and sleeve friction resistance from the cone penetration test (CPT), to shaft and toe pile resistances (Schmertmann 1978; Meyerhof 1976; Nottingham and Schmertmann 1975; Nordlund 1963; Eslami and Fellenius, 1997; De Ruiter and Beringen 1979). Although these methods were generally developed using data from specific geological regions, they are often recommended in national design manuals (e.g., FHWA, Hannigan et al. 2006).

Jan 1, 2018

By Andrew Port, Ali Ghandeharioon

Nonlinear seismic deformation analyses using the finite difference program FLAC were performed for a wastewater treatment plant to estimate foundation displacement and performance of two proposed trickling filters during the 2475-year event design earthquake. The effective stress based constitutive model UBCSAND, which captures the cyclic behavior of both the “sand-like” and “clay-like” materials, was used to model the dynamic response of the soil strata. Dynamic analyses of the site indicated that in absence of ground improvement or deep foundations beneath the proposed trickling filters, those structures would undergo horizontal displacements in excess of 1 m and short-term differential settlement gradient of about 400 mm over 50 m as a result of seismic and post-seismic settlements. Three mitigation options were considered for limiting the seismic displacements and differential settlement gradients of the proposed trickling filters. These alternatives include vibro-replacement stone columns, vibro-replacement stone columns plus supplementary cutter soil mixing (CSM) configurations, and pile foundations. Various layouts for each mitigation option were considered including the lateral extent of the ground improvement, CSM walls and pile spacing. Seismic horizontal and vertical displacements of the proposed structures as well as post-earthquake consolidation settlements due to dissipation of excess pore water pressures in soil layers were assessed in all the analysis alternatives. The analyses indicate that all the alternatives considered have the potential to provide a comparable level of seismic and post-seismic performance. However, for similar performance levels, the ground improvement options need to extend well beyond the edges of the proposed structures, while the piles can be limited to just beneath the footprint of the structures. INTRODUCTION Annacis Island Wastewater Treatment Plant (AIWWTP) is owned and operated by Greater Vancouver Sewerage and Drainage District and services a population of approximately 1 million people in Vancouver, British Columbia. Wastewater is generated by residential, commercial, and industrial sectors and the treated effluent is discharged to Annieville Channel of Fraser River on the south side of Annacis Island. AIWWTP is located on a 51-hectare site and was commissioned in 1975 as a primary treatment plant, but has had two major expansions to meet the population growth needs, and to improve the treatment process efficiency through the provision of secondary treatment of the liquid stream. The current expansion includes construction of additional solids contact tanks and secondary clarifiers. Future expansions include the construction of proposed additional trickling filters. New expansion structures are required to be designed for post-seismic operation after the 2475-year event design earthquake.

Jan 1, 2018

By Eric R. Bauer

The U.S. Bureau of Mines, in cooperation with a southwestern Pennsylvania coal mining company, BethEnergy Inc., Mine No. 60, Eighty-Four, PA, recently assessed the feasibility of using pre driven recovery rooms (open entry recovery) when longwall mining to increase the productivity of the coal extraction process. Two recovery entries, one 200 ft long and another 600 ft long, were supplementally supported with bolts, channels, and wire mesh, and either fly ash-cement piers or fiber cribs, then mined into by the longwall face. The recovery entries showed little deterioration as the supports provided adequate resistance to the front abutment loading. Compared with conventional recovery methods, the fullface recovery room allowed for panel extraction to be completed nearly 17 days faster and to reduce face equipment move time by 1-1/2 days. The potential productivity increase accompanying recovery rooms is greater than the cost of supporting a fullface recovery room. The fullface recovery room provided over 18 additional production days and the opportunity to mine nearly 68,400 st of coal per year per panel mined.

Jan 1, 1989

By William H. Pomroy

Fire on surface mining equipment is a serious hazard to life and property. The Bureau of Mines, through a program of contract and in-house research, has developed and in-mine demonstrated reasonably priced, reliable automatic fire protection systems to deal with this problem. This report reviews the development and subsequent testing of systems for haulage trucks, front end loaders, coal augers, dozers, drills, and shovels. A variety of fire sensors, extinguishing agents, and control systems arc discussed in the context of mine equipment designs and operating environments

Jan 1, 1980

By John A. C. Fortescue

There is a need for better communication between scientists who plan and carry out mineral exploration research in glacial terrain and the exploration geologists who look for mines. In this paper, four ways in which workshops could be used to close this communication gap are described and discussed in relation to the solution of this problem in Canada.

Jan 1, 1973

By J. Björkvall, S. Ångström, L. Kallin

In this paper results from industrial trials of CaC2 injection during stainless steel production in an electric arc furnace at Sandvik Steel is presented. The main purpose of the investigation was to analyse the effect of the injection on slag foaming and final chromium oxide concentration in slag. The results show that both an increase in slag foaming and a decrease of the final chromium oxide could be obtained during the charges with CaC2injection. On the basis of the results, the economical requirements are also discussed. Both the technical and economical requirements could be achieved for steels alloyed with Mo. In order to secure the economical requirements for all steel grades of interest, the injection technology must be further developed. It would also be important to utilize the positive effect of the slag foaming on the electric energy consumption. The work has been performed as a part of MEFOS frame research programme with participants from Sandvik Steel, AKZO Nobel and Avesta Polarit. Keywords: stainless steel, EAF, slag foaming, injection, CaC2

Jan 1, 2004

By M R. Stevens

An approach of geological mapping and descriptive criteria has been used to identify hydrothermal eruption breccias, named the Onemana Breccia. These in part mantle a gold bearing fossil hydrothermal system located on the eastern side of the Coromandel Peninsula, New Zealand. Whilst eruption breccias are documented from active and recent geothermal centres within the Taupo Volcanic Zone and in Northland their recognition at Onemana is the first confirmed discovery for this lithotype within ancient hydrothermal systems of the Coromandel Volcanic Zone. At Onemana the widespread occurrence of silicification, sinters, volcanic lake sediments, eruption breccias and advanced argillic alteration allows classic hot spring epithermal modelling. The geological setting, distribution, lithological characteristics, hydrothermal alteration and trace element geochemistry of the Onemana eruption breccias are described. These breccias are closely comparable with hydrothermal eruption deposits elsewhere, particularly those in active ore forming hydrothermal systems. Consideration is given specifically to the role of the Onemana Breccia in an exploration strategy for discovering epithermal gold-silver deposits.

Jan 1, 1991

Individual specimens of sphalerite from the Broken Hill lode vary considerably in manganese and iron contents, even within the same orebody, so that study of the overall variation of manganese and iron content of the sphalerite calls for the analysis of a large number of specimens. This difficulty has been overcome by analysing a series of recleaned zinc concentrate products, prepared from stope samples and their equivalents, from most of the developed sections of the lode. The analyses reveal that during the formation of the sphalerite the concentrations of iron, manganese and zinc in the mineralizing solutions varied independently of one another from place to place in the forming orebodies, and also in time.The overall pattern of variation of the iron and manganese contents of the sphalerite in the several orebodies of the lode bears a general resemblance to the overall pattern of distribution shown by several other elements, notably, cadmium, lead, bismuth and arsenic. The iron content of the sphalerite indicates that it was formed at a temperature of 6000 C. or higher, but the variation in its iron and manganese contents demonstrates that Kullerud's method for determining the temperature of formation of sphalerite from its iron content must be used with caution if only single specimens of sphalerite are available.INTRODUCTIONThe four chemical analyses available of specimens of practically pure sphalerite from the Broken Hill lode (Table 1) reveal that the manganese content of the sphalerite varies considerably, and that there is a significant variation in its iron content. The variations revealed between individual specimens within the same orebody in the same mine suggest that specimen material is unsatisfactory as a basis for studying the overall manganese and iron contents of Broken Hill sphalerite, unless a great number of specimensis analysed.

Jan 1, 1956

By E. Matinde

Poor phase separation and fine dissemination of the desired components within congruous slag phases are key challenges limiting the recoverability of values from slags by conventional beneficiation methods. Slag microstructure conditioning is a pragmatic approach to increasing themvalue-in-use of discard slags, especially when integrated with the broader smelter infrastructure. Although not yet tested on oxide slag systems, this paper explores the potential application of magnetohydrodynamic principles to the crystallization behaviour of bulk slags. Integrating the slag microstructure conditioning infrastructure to the existing smelter infrastructure is key to unlocking the economic value of slags because it is most economic to condition the properties of molten slag directly after tapping. A new business model that integrates smelting units to transversalmeconomic activities, such as cement production and suppliers of construction aggregates, canmsignificantly increase the circularity of metallurgical slags.

Oct 9, 2024

By Edward Thomas

Note. - Securing mine roof through consolidating thin or otherwise incompetent strata to increase overall thickness of the immediate roof beam is a new method of roof support and control which has aroused great interest amongst mining engineers and which is now being experimented with and thoroughly investigated by the United States Bureau of Mines. A paper on Roof Bolting, illustrated by photographs and motion-picture films, will be presented by Edward Thomas, of the U. S. Bureau of Mines, at the forthcoming Annual Meeting of the Mining Society of Nova Scotia. In the following pages, Mr. Thomas describes the methods used in roof bolting as illustrated by the photographs that accompanied his paper. The photographs are supplied through the courtesy of the United States Bureau of Mines, whose willing cooperation with miners and mining engineers in Canada is very well known and even more greatly appreciated. This method of publishing Mr. Thomas's paper is adopted because few, if any, Canadian mining engineers have actually seen installations of roof bolts and it is felt that the best possible presentation of such an interesting subject through the medium of the Bulletin will be attained by publication of the photograps over explanatory captions. - Ed.

Jan 1, 1950

By Peter A. Anderson

Innovative solution management is being used at Coeur-Rochester Inc. to increase bullion production and decrease overall costs. New operating programs call for reduced solution application rates to the heap that increase pregnant stream values at a lower and less costly plant flow rate. Silver and gold extractions are equal regardless of leach solution application rate. Solar heating is used in the summer months to increase the core temperature of the heap for use in the winter months to enhance the silver extraction rate. The Coeur-Rochester silver and gold mine, located in central Nevada, is an open pit, heap leach operation that has been in production since late summer of 1986. The facility produces about 15.4 kt/d (17,000 stpd) of -13 mm (-0.5 in.) ore to a leach area consisting of more than 37 hm2 (4 million sq ft) of 80 ml HDPE liner. Crushing is accomplished with a 1220x 1520-mm (48- x 60-in.) jaw crusher. This is followed by a single 2.1-m (7-ft) standard cone crusher and is completed with four 2.1 m (7 ft) short-head cone crushers. Agglomeration is not required for the crushed ore, which contains less than 10% -75. µm (-200 mesh) material. The ore contains 53 g/t (1. 55 oz per st) silver and 0.377 g/t (0.011 oz per st) gold. It is end dumped over previously leached material, leveled, and then ripped with a bulldozer. Drip emitters at 810 mm (32 in.) spacings on 910 mm (36 in.) centers are used to apply barren solution to the heap. A portion of the emitter lines are buried I m (3 ft) deep during the winter months and are placed on the surface the remainder of the year. The leach solution contains 0.75 g/L (750 ppm) sodium cyanide solution at a pH of 10.5 - 11. Dissolved oxygen averages 8 ppm in the pregnant solution. Cyanide consumption for the ore to date is just under 0.2 kg/t (0.4 lb per st). The pH control is accomplished by adding I kg/t (2.0 lb per st) 0-10 mm (-0.4 in.) pebble lime to the ore at the tertiary crusher. The pregnant solution is processed by a conventional closed circuit Merrill-Crowe system. The pregnant solution is clarified through three 158 L/sec (2500 gpm) US Filter Auto-jet clarifiers. This is followed by deareation through a

Jan 1, 1989