Search Documents

By Sangseom Jeong, Kyoungyul Kim, Jaeyeon Cho

"Abstract The lateral earth pressure of vertical circular shaft is investigated by using experimental tests and a theoretical analysis. The emphasis was quantifying on the magnitude and distribution of a lateral earth pressure measured by three-dimensional arching effect. A framework for determining the earth pressure distribution on the basis of both centrifuge model and full-scale field test results is introduced. Through these studies, it is found that the lateral earth pressure decreases within active displacement (dh/H: 0.2×10-2, dh: horizontal displacement, H: Height of vertical shaft) of wall at deep excavation and the arching effect is more significant for deep excavation than for shallow excavation. It is also found that the lateral earth pressure acting on a vertical circular shaft considering arching effect is 70% smaller than that calculated by Rankine theory, and thus represents a significant improvement in the prediction of realistic earth pressure for vertical circular shaft subjected to arching pressure.INTRODUCTIONIn South Korea, an increasing need for underground excavation and the application of the vertical circular wall (i.e. vertical shaft) is becoming an important issue in engineering practice. Here the vertical circular wall is generally embedded in soft or hard rocks through weathered soil varying thicknesses ranging up to 15 m. Since 1980, a number of huge excavation projects such as underground space for constructing power stations, subways, high-speed railways, and many lifeline constructions have been performed in urban areas (Jeong and Seo, 2004). Although there have been considerable advancements in construction techniques involving vertical circular wall, it is still very important for tunnel engineers to control the lateral earth pressure. Additionally, Proper estimation of earth pressures is a key factor in design of vertical circular wall. Because of three dimensional arching effects, i.e. convex arching and/or inverted arching, the earth pressure acting on a circular type of wall is less than other types. Thus, the vertical circular wall is generally used."

Jan 1, 2014

By A. W. Jolliffe

AEROPROSPECTING may be defined as the application of the air view to the search for mineral deposits. The term is suggested as a preferable alternative to either aerial prospecting (which may be confused with areal prospecting) or air prospecting. The air view may be obtained by visual observation from an aircraft or by examination of air photographs; each has its particular advantages and disadvantages. Aeroprospecting should be regarded only as an aid to, and not as a substitute for, accepted prospecting methods ( l ). The Precambrian region north of Great Slave lake consists of two well defined physiographic units, a feature first noted by J. T. Wilson (2). The boundary between these lies close to the north shore of the east arm of the lake and extends northwesterly near Spencer, Beniah, Carp, and Ghost lakes (Figure 1). South and west of this line, exposed bed-rock makes up the greater part of the land area; eskers are very rare, and overburden is largely limited to rock-walled valleys and depressions. North and east of the line, outcrops are rare or absent, eskers are abundant, and most of the surface consists of drumlin-like drift hills, elongated parallel to the direction of ice movement (Figure 2). Where this boundary passes through the area shown in Figure 1, it lies near the 1,200-foot contour and may mark the maximum extent of the lake or sea arm present in this vicinity toward the end of the Pleistocene period. For convenience, the first area may be called the 'bed-rock belt' and the other the 'drift belt'.

Jan 1, 1945

By Thomas G. Chapman

The four major steps in the production of marketable copper are mining, concentrating, smelting, and refining. In a few cases, however, leaching takes the place of concentrating, smelting, and refining, and in others ores are smelted without being concentrated. Copper ores have been milled since the early days of mining in the United States. Except in the Michigan district, most copper ores went direct to the smelter until the so-called porphyry mines were developed. At present, although considerable leaching and direct-smelting ores are produced, the bulk of the copper ore mined is concentrated. Improved methods of concentration have kept pace with the increased tonnages of ores milled.

Jan 1, 1936

By Grover Wallace

At is important for today?s mining executives and leaders not to underestimate the fact that, while the recent downturn in the economy did take its toll on balance sheets and productivity, factors such as emerging countries, aging workforces, globalization and individual knowledge growth did not lay dormant while the economy was in a lull. It is key for mining leaders to be proactive in their talent strategies. Successful mining companies are developing a clear, concise and communicated strategy and placing a high priority on recruiting the right talent in global markets that parallels their business strategy. They are focused on placing the right people in the right jobs.

Jan 1, 2011

By J. A. M. Cano

An extensive research work was developed by Samarco Mineracao S/A to study the quality characteristics of blast furnace pellets produced with high content of MgO. Comparative blast furnace simulation tests were conducted both in Samarco and foreign laboratories. The objective was to evaluate the behavior of high MgO and normal Samarco pellets in the blast furnace operation. Additives such as dolomitic hydrated lime, dunite and magnesite were used for increasing pellet MgO content. The test results showed that pellets produced with high MgO content are similar in quality to normal Samarco Pellets.

Jan 1, 1991

By William A. Sloan

"In smelting operations, finely divided material called ""flue dust"" is carried by the moving gases from the roasters and furnaces; it is partly settled and recovered in the flue system. The flue dust from copper smelters contains a high percentage of copper, usually some gold and silver, and occasionally other valuable metals. It is too valuable to throw away and in present practice is returned to the smelting furnaces for re-treatment. A part of this material again passes out with the gases and forms a circulating dust load in the system. The dust that passesout of the stacks into the atmosphere is an important source of loss in copper smelting. Loss of values also occurs by dust being blown away while in transit from the flues back to the furnace, and of course the greater the amount of rehandling the greater this loss.Dust carried in the gas currents causes corrosion of the roof arches in reverberatory furnaces. Returning flue dust to the furnace increases the quantity of suspended dust. Corrosion reduces the life of the arches and shortens the length of furnace campaigns; also the corrosion of arches limits the temperature at which a furnace may be operated. Every ton of material that must be re-treated in the furnaces reduces correspondingly the amount of new ore or concentrates that could be smelted.As the present tendency is toward finer grinding in flotation plants smaller particles will need to be treated at the smelters, increasing the difficulty of preventing losses in flue dusts. Many schemes and processes for a more economical method of treating flue dust have been proposed or tried, but in the main none of them has been successful."

May 1, 1928

By A R. Bye, T R. Stacey

Anglo PlatinumÆs Potgietersrust Platinums (PPRust) operates three open pits and plans to excavate 90 Mt of rock in 2007. With pit slopes expected to reach a height of 400 m, the geotechnical department has a key role to play. Over the last four years PPRust has successfully implemented new geotechnical strategies and tactics to reduce risk, improve safety and maximise profitability. A large database of core logging, face mapping and rock testing data has been assembled and used for failure analysis, geotechnical zoning and rock mass ratings. The data has also been used for optimising blast designs on a daily basis through the use of a geotechnical block model. This greatly improves blast fragmentation and therefore loading and milling efficiencies. The slope design process involves limit equilibrium analysis, numerical modelling, rock fall analysis and block modelling. Slope management includes comprehensive limit blasting and visual inspections, and state-of-the-art slope monitoring equipment, namely the GroundProbe radar, Riegl lasers and GeoMoS automated prism monitoring. The risk-consequence approach has been used in slope optimisation, where all the slope analyses, operational controls, costs of failure, economic analyses of various slope designs and fault tree analyses are used to determine the ideal slope designs. These activities added over $25 million of value to the operation and also ensured compliance with Anglo AmericanÆs acceptable risk level. The successful mining of the optimised slopes is to due to the greatly improved geotechnical knowledge and slope management. PPRustÆs geotechnical work is used as a benchmark for Anglo American open pit operations. The focus of the paper will be on the value added to the operation by all aspects associated with slope management.

Jan 1, 2007

By Jewel A. Gomes

Keywords: Electrocoagulation, arsenic removal, fuel cell, windmill, energy simulation, combined Fe-Al electrode assembly Arsenic contamination of well-water in different countries has caused signs and symptoms of arsenic poisoning. Although several physicochemical treatments are presently used for the removal of arsenic compounds from drinking water, an electrochemical treatment, electrocoagulation, is a promising processing technology and currently is the most efficient (above 99% removal) and environmentally friendly technique, particularly if combined with alternative energy sources. Wind and fuel cell technologies can be considered the most promising developmental clean power sources. We will discuss new insights into the materials processing mechanisms and show the coupling of electrocoagulation with fuel cells and simulated wind energy sources. Different electrocoagulation plate materials were considered, along varied currents from the fuel cell to produce maximum arsenic removal. Coupling these technologies will remove carcinogenic arsenic from water sources, and will exhibit efficient usage of these energy sources by producing pure water for human and agricultural consumption.

Jan 1, 2005

By B Poborowski, A Chen

"For some time, the Australian and Chinese underground coal mining industries have evolvedindependently with minimal infl uence on each other. Despite the fact that in recent years severaltechnologies and solutions have become common to both industries, this trend has seeminglycontinued to the point that there are still many important diff erences in legislation and hazardmanagement systems in both countries. Austar Coal Mine as an Australian based and Chineseowned enterprise has a unique opportunity to benefi t from the technology and knowledge ofboth nations. This paper compares the Australian and Chinese approach towards spontaneouscombustion hazard management in order to exchange experience, identify possible improvements and learn from each other."

Jun 1, 2012

By Jean Philippe Santos Gherardi de Alencar

O fenômeno de colagem é a formação de aglomerados de pelotas, denominados clusters, devido à sinterização do ferro gerado durante o processo de redução. O resultado disto é a elevação da perda de carga nos reatores de redução direta. Tal fenômeno vem sendo estudado por vários pesquisadores, pois as práticas operacionais dos reatores têm priorizado o uso de temperaturas de bustle gas (BG) cada vez maiores, o que potencializa o aparecimento dos clusters. Uma alternativa para controlar a colagem é por meio de utilização de agentes de coating (AC’s). Em relação às matérias primas utilizadas como AC´s, as questões que surgem agora são as seguintes: Como se comportam os AC’s em temperaturas muito elevadas de BG? Qual seria a maior temperatura possível de BG? A fim de começar a entender a melhor maneira de responder a estas questões foram realizados alguns testes de caráter exploratório e não convencionais para avaliar o comportamento de alguns materiais de coating a elevadas temperaturas de redução. Os resultados destes testes mostraram a possibilidade dos AC’s funcionarem a temperaturas maiores que a de inicio do amolecimento da carga e que, nestas temperaturas, a sua granulometria pode ser parâmetro determinante para seu desempenho. O aprimoramento dos ensaios de simulação do processo de redução em reatores de redução direta é fundamental para responder as questões que se apresentam em relação ao tema.

Aug 2, 2018

By R. F. Tenney

The performances of four anthracite-burning stokers have been observed under identical 74-hp. steam boilers. Fifty runs of 12 and 24 hours' duration were made in accordance with the test code of the American Society of Mechanical Engineers (ASME). The capacity of each stoker for burning anthracite has been determined, the heat efficiency at each fuel rate has been computed, and the various significant items of hear loss have been estimated. The operating data and results from each run are tabulated in this report in the form used in the test code. The heat efficiencies and most significant operating data for each run are also presented graphically for each stoker to establish the trends with increasing boiler outputs, The tests show that rice anthracite can be burned on stokers adapted to its use at heat-conversion efficiencies of 82 percent or more under continuous firing. These high efficiencies are maintained with fuel inputs 30 percent higher and lower than the peak efficiency rate. Moreover, a heat efficiency of 70 percent or more is obtained at 50 percent of the optimum fuel rate, even though the excess air into the furnace cannot be held below 150 percent.

Jan 1, 1960

By Thomas M. Barczak

This U.S. Bureau of Mines report examines the causes and consequences of longwall face sloughage. Theoretical relationships were developed to evaluate mechanisms that produce slough age. From these relationships, contributory factors were identified for further analysis in field efforts. A survey identified 12 mine sites with sloughage problems, and these were investigated. From these studies, it was determined that the depth of cover and mining height are the two most significant factors causing sloughage on longwall faces. Coalbed friability and cleat orientation also were found to be significant factors in promoting sloughage. It was concluded that sloughage is primarily a problem in thicker seams or seams with friable coalbeds, and that the problem is more severe as the depth of cover increases. Sloughage also was found to increase as the rate of mining decreased. Observations indicated that face slough age can increase dust generation significantly on longwall faces. Current efforts to control dust generation from longwall sloughage are described.

Jan 1, 2010

By N. B. Pundari

Proper selection of large walking draglines, based on sound engineering principles and field experience, has not kept pace with the large capital expenditures needed to buy these stripping machines. The use of large walking draglines for stripping overburden in US surface coal mines grows steadily, but equipment selection continues to pose problems. An improper size, model, make, or spoil reach selected for a particular stripping application results in additional, unnecessary coal production costs. Large walking draglines are being used to dig deeper tar sands at the Syncrude operations near Fort McMurray in Northern Alberta, Canada. This application is compared with typical deep digging operations and dragline use prevalent at typical US strip mines.

Jan 4, 1981

By N. A. Karl, D. R. Wilburn

"This summary of international mineral exploration activities for the year 2016 draws upon information from industry sources, published literature, SNL Metals & Mining (SNL), an offering of S&P Global Market Intelligence (New York, NY), and specialists in the U.S. Geological Survey (USGS) National Minerals Information Center. Three types of information are reported and analyzed in this annual review of international exploration: 1) budgetary statistics expressed in U.S. dollars provided by SNL; 2) regional and site-specific exploration activities that took place in 2016 as compiled by the USGS and 3) regional events and legislation that affected exploration activities including economic, social and political conditions, which were derived from published sources and discussions with USGS and industry specialists. Commodity and regional compilations are presented in this summary. Because multiple sources were used to develop commodity and regional compilations, statistics may vary depending on the source and type of data that are being reported. The SNL data summarize budget estimates for worldwide exploration activities in 2016 for 30 nonfuel mineral commodities and metal alloys, based on company surveys. Surveys focused on precious metals (gold, platinumgroup platinumgroup metals (PGMs) and silver), base metals, (cobalt, copper, lead, molybdenum, nickel, tin and zinc), bulk commodities (bauxite, chromite, iron ore, manganese, phosphate and potash) and other commodities (aluminum, antimony, diamond, graphite, heavy-mineral sands, lithium, niobium, rare-earth elements (REEs), scandium, tantalum, tungsten, uranium, vanadium and yttrium). Information on uranium exploration activities was included in SNL’s survey for the first time in 2007. Data on lithium, niobium, phosphate, potash, REE and tungsten were compiled for the first time in 2010, and scandium, vanadium and yttrium were added in 2014 because of their increased topical significance. Since 1999, companies with exploration budgets of $100,000 and greater were included in the SNL surveys. SNL budget estimates exclude coal, and oil and gas. The 2016 SNL mining company survey compilation was reported by SNL to include an estimated 95 percent of the world’s nonfuel mineral exploration budgets. The 5 percent that was not covered was accounted for by companies that chose not to participate in the SNL survey, private companies that do not publish their budget data and government-funded exploration activities."

Jan 5, 2017

By Tom Barry, Kameron Ray, Dr. Gavin Yuill

Imerys Talc, Yellowstone Mine in Montana faces significant geotechnical challenges such as poor wall quality and local instabilities. These instabilities are driven primarily by the characteristics of the rock mass, but are aggravated by drilling and blasting operations.

Jan 1, 2016

By H. Ozturk

In this paper, the computer program ‘SHAFT’ developed for estimation of support requirements for circular mine shafts is introduced. Theory of support design is based on the analytical solutions of circular excavations under non-hydrostatic loading (Detourney and St. John1), and Lame’s thick-wall cylinder theory (Timoshenko6). For rock mass strength property determination Hoek-Brown failure criterion (Hoek et al.2) is used. Mainly two types of support, concrete and steel are taken into consideration as a support member. Program is written in Quick Basic language. Input parameters of the program are shaft radius, number of zones having the same properties along the shaft depth, and depth, unit weight, horizontal to vertical stress ratio, GSI, and uniaxial compressive strength of intact rock of each zone, and compressive strength and safety factor of support member. Output of the program is the graphical representation of shaft with the required support member and thickness throughout the depth of the shaft.

Jan 1, 2003

By Wendy L. Naysmith

This paper deals with the various options considered and factors that influenced the final selection of the headframe, shaft layout and hoisting systems required at the Impala No 16 Shaft in order to hoist both the required 3 Mt of ore per annum, and transport men, material and equipment between the surface and the underground workings to a depth of 1640 m. The layout and construction method used for what is at present the world?s tallest concrete headframe is discussed together with the integrated hoist room foundations designed to suit multiple mechanical and electrical hoist supplier?s solutions. The mechanical components of the two tower mounted 6,5m 4 rope Koepe hoists and deflection sheaves and their layout is dealt with in detail. Various features of the bearing type, brake units and brake control system are also discussed. Installation of the mechanical and electrical hoist equipment in the headframe took place during the sinking phase of the project and placed severe restrictions on the use of the heavy lifting facilities. This required a well-managed and systematic approach to delivery of the hoist components and associated equipment, as well as close co-operation between all contractors on site.

Oct 1, 2010

By H. Kenworthy

The purpose of the study described in this publication is to develop methods for recovering simple master alloys or single metal components from discarded and scrapped S-816 alloy, The Bureau of Mines started this investigation late in 1955 after the need became apparent for a method of reclaiming high-temperature alloys from an ever-increasing accumulation of rejected and wornout jet engine turbine buckets. Laboratory studies showed the following: (1) Pyrometallurgical separations are not selective enough, (2) several methods can be used for effective chemical dissolution of the major constituents of the alloy, (3) a master alloy or complex salts of cobalt and nickel can be separated, (4) chromium, contaminated by several other metals, may be segregated, and (5) more time and effort need to be expended in separating the minor constituents and improving the purity of the major metals removed. Difficult and incomplete chemical separations were attributed to the complexity of alloy composition, as were the long tedious chemical analyses o' products. For determination of several of the metallic components, standard methods of separation and routine analytical procedures had to be considerably modified to achieve satisfactory results. The overall technical problems involved in separating S-816 components do not appear to be insurmountable; however, refinement of several of the methods used in this investigation is desirable.

Jan 1, 1961

By Jörg Fischer-Bühner

Conventional 22ct Au jewellery alloys are comparably soft in the as-cast and soft-annealed state and hardening by cold-working is the only way of giving strength to the jewellery. The paper first focuses on hardening of 22ct jewellery alloys by conventional means, i.e. solid solution hardening with base metals (aiming particularly at an increased as-cast hardness) as well as precipitation hardening by alloying with base metals beyond the solubility limits and subsequent age-hardening heat treatment. Co-additions of ~2% turned out to result in most pronounced solid solution hardening up to ~100 HV1 in an investment cast & quenched state. Subsequent heat treatments, consisting of solution annealing at 850°C for 1h followed by water quenching and ageing at 300°C ? 400°C for ~ 1h lead to pronounced age-hardening with a peak hardness of ~ 260 HV1. In contrast, 22ct Au alloyed with Ni, Fe or Sb display no age-hardening effect within the same range of heat treatment parameters. The 2nd part of the paper reports on some preliminary trials to enhance the hardening effect of the base metals by additions of suitable elements, which possess a strong tendency to phase formation with the added base metal during ageing treatments. It is shown, that the age-hardening behavior of 22ct and 990/995 Au alloyed with Co or Ni can be remarkably influenced by additions of Sb. A total of only 10wt%0 of CoSb or NiSb-additions lead to a peak hardness of ~ 150 HV1 for a 22ct Au and ~ 100-120 HV1 for 990 Au , which is obtained already after very short ageing times (20-40min) at 300-400°C after solution annealing at 700°C / 1h / water quenching. It is suggested that the age-hardening mechanism in these alloys consists in precipitation of intermetallic CoSb- and NiSb-phases.

Oct 1, 2003

By W. Dziurzynski, S. Nawrat, A. Krach

The paper presents research on the influence of the goaf methane inflow on a fire. The problem was investigated by a computer simulation of a fire developing in a goaf. A relevant mathematical model of the fire was selected, which considered both burning of coal and methane. The combustion process is very sensitive on the oxygen and methane concentrations, which was indicated on graphs of the fire temperature evolution. Examples of computer simulation for various location of the fire were considerd. Analysys of results confirms the influence of the content of the goaf methane on development of fires.

Jan 1, 2003