Search Documents

By C. C. Clark

This report presents the results of tests conducted by the U.S. Bureau of Mines to determine the transport characteristics of highly concentrated paste backfill mixes made from dewatered total mine tailings. The slurry concentrations of the mixes were all above 78 pct by weight with slumps ranging from 6.4 to 16.5 cm (2.5 to 6.5 in). Laboratory material property tests and full-scale pumping tests were conducted using pipe diameters of 102, 128, and 154 mm (4, 5, and 6 in) and a positive-displacement pump. The results indicated that the tested backfill mixes can be successfully transported as a stiff paste and identified the influence of and the interaction among the various mix and system variables.

Jan 1, 2010

The optimisation and validation of shearer cutting methods is a time consuming engineering task. Many different parameters, of which not all can be controlled, can vary. The easiest solution, to increase the installed power and the longwall length, is not always the best. A different cutting method can increase the capacity without the need of new machines. The Department for Mining and Metallurgy Machinery at RWTH Aachen University therefore developed ProSL, the simulation tool for shearer and longwall operations. ProSL enables the engineer to create his own cutting methods and compare it with other methods. Machine-data can easily be varied to see the impact on the method. The research shows that sophisticated longwall methods increase the productivity of the system. The paper presents the results of the calculation with ProSL and shows how higher efficiency and lower costs can be achieved.

Dec 6, 2010

By G. S. Hume

THE discovery of natural gas with naphtha in 1924 in the Upper Palaeozoic limestone of Turner Valley, 35 miles southwest of Calgary, has led to continuous developments in this field. Drilling undertaken soon after this discovery demonstrated that the anticlinal structure was in reality a major drag-fold cut off on the east side by a westerly inclined fault of large displacement. The faulted edge of the .limestone at depth determines the eastern limits of the field, which between 1924 and 1936 was shown to have a gas area 14 miles long by about 1 mile wide. Since the strata dip westerly, away from the axis of the fold, drilling becomes progressively deeper to the west and, with the advent of deeper drilling, crude oil was discovered in 1936 on the west flank of the structure but in the same porous reservoir rocks as the gas on the crest and upper parts of the fold. Since 1936, drilling has been undertaken wholly for the production of crude-oil and at present two producing areas have been found within the Turner Valley structure. The larger of these, at the south end of the field, in the vicinity of Highwood river, has a length of about 4 3/4 miles and a proved width of one mile, whereas the smaller, in the north end of the field, south of the north fork of Sheep river, has only a few producing wells.

Jan 1, 1939

By R. D. Govier

The U.S. Bureau of Mines has developed a thin-film X-ray fluorescence technique to rapidly determine Cu, Ni, Co, Fe, and Cr in super alloy leach liquors. Total analysis time per sample was less than 15 min, as opposed to several hours for traditional wet chemical methods. Precision and accuracy were checked by replicate analyses of solutions similar in composition to leach liquors, whose analyte concentrations were well known. Coefficients of variation for all elements were found to be less than 2 pet. With the exception of the results for Fe, all relative errors of estimation were also found to be less than 2 pet. Bulk liquids are not introduced into the spectrometer; thus, the potential for damage to the instrument by leakage of corrosive liquids is eliminated.

Jan 1, 1989

By P. R. Brenchley

Main ore pass systems should last the life of a mine, and too often expensive and hazardous remedial measures are required to repair a damaged ore pass in an attempt to extend its life. In order to maximize the life expectancy of all ore passes at Moab Khotsong, ?wearing blocks? and ?softer support? systems, combined with basic rock engineering principles, have been implemented. Failure of an ore pass can have severe financial implications, both indirectly because the ore pass cannot deliver the broken rock either from level to level or directly in the shaft ore pass system to the required level for tramming to take place, and directly due to the cost of the repair work that is required. Several factors need to betaken into consideration so that production interruptions are eliminated or minimized. Investigations of damaged ore passes at Moab Khotsong and surrounding mines revealed some interesting mechanisms of damage, and some innovative methods of reducing or eliminating the damage have been implemented at Moab Khotsong. The system design was based on 30 years, experience in main shaft rock passes. The design was to counteract scaling, hang-ups and dust problems associated with main rock passes, and the objective was to increase the life of rockpasses. These problems, including the initial design aspects to try and eliminate the repair measures, are discussed in detail.

Jan 1, 2006

By Donald E. Redmon

Industrial engineering departments perform staff duties and are most effective when sincerely supported by management. In accordance with the needs and desires of the mining companies involved, various industrial engineering functions have been adopted widely at western metal mines during the period 1950-60. Newly organized departments usually conduct method and equipment studies, work-measurement programs, and establish and maintain production standards. Supervisor-training programs and courses are effective in showing the relationship between supervisory responsibility and the purpose for which industrial engineering is practiced. Industrial engineering staffs of western metal mines are composed predominantly of personnel from within the companies. Experienced industrial engineers, not necessarily experienced in mining, frequently are hired by a company to help establish the department. Management consultants frequently are called upon to advise management and instruct department personnel in industrial engineering practices. Some departments have developed satisfactory industrial engineering programs without benefit of formal industrial engineering training or advice.

Jan 1, 1962

By M Furche, U Noell, C Grissemann, J A. Meima, T Graupner, A Romero-Baena

The mining residues at the abandoned copper mine site Pe±a de Hierro, located at the headwaters of the Rio Tinto, contribute substantially to the pollution of the river with high loads of Fe, As, Pb, Zn and Cu. The pH of the outflow ranges from 0.5 to 2.4 in the dry and wet season, respectively. One heap composed of alternating layers, which were deposited parallel to the slope, was investigated in detail. Unsorted blocky to fine materials including gossan material, pyritic volcanics, ashes from pyrite combustion and slate were observed here. The top of the heap has a gentle slope and a hill contouring channel-rip morphology. The initially rugged surface was smoothed by heavy rainfalls filling up the pores of the blocky material with fines. These fines are capable of storing the water for a prolonged time, providing an extended reaction time close to surface in a dry climate at extremely low pH conditions (one to four). All minerals, pyrite, mica, barite and even quartz (probably due to F released from dissolved mica) have been digested and silica gel precipitates have formed a stable and quasi impermeable 100 ¦m layer with very low porosity (<5 area per cent, estimated using scanning electron microscopy (SEM) imaging). The silica layer itself is covered by Fe-oxy-hydroxide (ie FeOOH) coating (10 ¦m) and seals a 1 - 5 mm thick stable hardpan. This hardpan covers the channels and part of the rips almost entirely, guiding the rainwater subhorizontally towards slopes and sinkholes. By geoelectrical measurements, a 3D-resistivity model of the internal structures and the bedrock relief underlying the heap was generated. Internal structures relate to lithological changes in a number of layers. Zones of low resistivity may be attributed to washed-in fines within the mega pore system, whilst zones of high resistivity close to the surface probably reflect the advanced stage of drying beneath aging hardpans. The water movement at the surface was investigated by an artificial precipitation experiment with monitoring of the subsequent changes in resistivities.

Jan 1, 2008

By Shu Xinqian, Zhou Weining, Shan Zhiqiang, Feng Jifu

"Modified calcination conditions on the extraction of rubidium resources from muscovite (KAlz[AlSi301o](OH)2) ore are systematically studied. The impact of various factors on the rubidium leaching rate is also analyzed, including the agent types, roasting time, the mass ratio, roasting temperature, etc. The results indicate that the best agent is a combination of sodium chloride and calcium chloride, its mass ratio ofmuscovite/NaCl/CaClz is 1:0.25:0.25. Calcined at 8500 for 30 minutes, the rubidium leaching rate is up to 90%. The reaction of muscovite ore with the chlorinating agent CaC12 has been studied by TG/DSC, the calcined intermediates are identified by XRD, and the surface morphology before and after leaching is characterized by SEM. Rubidium chloride products can be obtained with a purity of 92% by using t-BAMBP extraction, hydrochloric acid reextraction and purification.IntroductionRubidium is one ofrare alkali metals, which is found in 1981 by German R.W. Bunsen and G.R. Kirchhof. Rubidium includes the following features: atomic number is 37, each atom weight 85, the body-centred cubic lattice, each unit cell has two metal atoms, and the density is 1.532g/cm3. The properties of low melting point (312.46 K) and malleability make rubidium have a strong chemical activity and photoemission. Rubidium provides a main material for manufacturing phototube with a wide range oflight waves, which possess high sensitivity and stability. Efforts are being made to carry out research on rubidium ion gngine, magnetic flux generators and thermoelectric transudcer, etc. Rubidium exists in muscovite ore(KA12[AlSh01o](OH)2 (monoclinic system and hexagonal layered structure) as isomorphism and replace the large radius of the potassium atoms, as well as part of rubidium locate between structure layers. The complex components bring great difficulty in comprehensive recycling."

Jan 1, 2013

By Virgil A. Marple

It was the purpose of this contract to conduct research in several different areas of instrumentation used to determine the quantity of respirable dust in the mining atmosphere. One area of research was in evaluation of instruments including several respirable dust monitors, several types of photometers, and a QCM cascade impactor. An instrument evaluation chamber was developed to aid in evaluating the instruments in a dust atmosphere. Another area of research was investigations into new instrumentation concepts, such as a virtual impactor/photometer instrument, a new optical device which can be used as either an optical particle counter or photometer, a new personal respirable sampler, which employs an impactor instead of a cyclone as a preclassifier, and the development of a new cascade impactor, which deposits the particles uniformly on the impaction plate. Another area of research included the use of many of these instruments in two field studies, including a silica sand plant and a tungsten mine.

Jan 1, 1981

By Osvaldo A. Bascur, Curt Heftier

The lack of integrated information including the Energy/Utility Suppliers with sufficient detail for analysis causes inefficient operation in metallurgical complexes including the Energy/Utility Suppliers . Defining the right context for information use is essential for sustainable operations. This being said, what are we doing to enable people to act upon information and to be aligned to optimize the use of resources like raw materials, energy, water and consumables for an entire metallurgical complex? Collaboration between all company entities is a key component of improving efficiency. Evolution of web technology and object modeling of enterprise assets enables collaboration across the whole business. Operational troubleshooting occurs more quickly as the organization acts on issues to reduce wasteful operation. This paper presents a real time software infrastructure with tools that give users the ability to sift through available data, transform data into information for business continuous improvement and optimization. We will introduce a new technology for analyzing real time data, information and events using multidimensional analysis of information to detect anomalies based on the statistics of the data classified by time events to reduce the information into action. A new paradigm for collaboration at a local and strategic level is proposed to enable the enterprise to become proactive in dealing with wasted time and products. Three examples from the industry will presented and their benefits highlighted.

Jan 1, 2011

By M. A. Kujoana

Following on the design of good mining layouts and regional support systems, and the implementation of sound strata control practices, stope support is the ultimate strategy to combat the hazards of rockfalls and rockbursts. The primary function of stope support in intermediate and deep level mines is to stabilize the rock mass immediately surrounding stoping excavations, that is, the zone of fractured rock which behaves in elastically around stopes. Support design is a process resulting in a support system which is both practical and meets or exceeds by a factor of safety the requirements for a particular geotechnical environment. The aim of this project was to design a support system, which accommodates the factors of rockfalls and rockbursts. The pack support unit must be easily handled, less costly and can be used in stopes without any significant convergence. The project tested the structural stability of packs to their expected deformation, in order to design a height to width ratio for stopes where little convergence is expected.

Jan 1, 2009

By Brian Wilson, Megan Atkinson, Richard Diggle, Nathan Sweeney

"Ruskin Dam, located near Mission, British Columbia, was constructed in 1929 and 1930 and comprises of a concrete gravity dam structure founded on bedrock. At the right abutment, which consists mostly of dense to very dense sands and silt, the dam abuts against overburden soils, and connects to a cutoff wall system consisting of sloping concrete slabs. Significant seepage and piping issues were encountered during first filling of the reservoir in 1930. In 2012, BC Hydro, the owner of the dam, awarded a contract for the construction of seepage control measures at the right abutment, including construction of a plastic concrete cut-off wall extending upstream of the dam, a plastic concrete seepage training wall extending downstream of the dam, tie-in of the new cutoff wall to the dam, consisting of jet grouting of the soils adjacent to the dam to allow for the construction of the special cutoff connecting the cutoff wall to the dam, and construction of additional jet-grouting ground improvement downstream of the dam.Integral to the upgrade was the requirement for the special tie-in cutoff wall, consisting of a highly flexible, impermeable membrane to connect the concrete dam to the new, 1 m thick plastic concrete cutoff wall. The tie-in extends vertically into bedrock through the dam and jet grout columns constructed adjacent and beneath the overhanging portion of the dam at the right abutment. The membrane is required to survive the anticipated earthquake induced deformation between the dam and the abutment soils.This paper describes the processes used to develop a material suitable to meet the specified flexibility and permeability criteria, as well as the innovative construction techniques utilized to construct the slot and place the bituminous material within it. The final dimensions of the slot were in the order of 7 m long by 25 m deep by 0.17 m wide. The bituminous material was placed under a head of water which was required to maintain stability of the slot, and was placed at temperatures in excess of 120 degrees Celsius."

Jan 1, 2017

By Marvin E. Lane

Viburnum, located in the foothills of the Ozarks in south-east Missouri, is the site of a modern lead mining and milling operation. Two mines are currently producing a total of 5,000 tons per day and a third mine is in the final development stage, with full production scheduled for late this year (1964). These mines will supply the tonnage required to keep the Viburnum mill operating at a full capacity of 7,000 tons per day for many years. The efficient underground mining operation is completely trackless. Drill jumbos are used to break the ore in a room and pillar method of mining. Transloaders, or St. Joe shovels, and trucks do the loading and hauling. The Viburnum mill has a world-wide reputation as a most efficient operation. This is due to the extensive use of automatic process controls, and labour saving materials handling facilities. Introduction THE St. Joseph Lead Co., has operated lead mines in southeast Missouri for 100 years. These operations have been confined largely to the area called the

Jan 1, 1964

By C. J. Wilhelm

Brine produced from subsurface formations may be employed successfully instead of fresh water as a flooding, medium in the secondary recovery of oil. The feasibility of this substitution has been proved in the shallow "shoestring" area of eastern Kansas and northeastern Oklahoma, where the supply of fresh water often is limited. In this procedure all brine produced with the oil is returned to the formation and thus is prevented from contaminating streams and fresh-water supplies. This report includes a detailed description of a "flood project" in eastern Kansas studied by the Bureau of Mines. In an attempt to determine whether brine, when handled properly, can be used as effectively as fresh water in flooding oil from partly depleted, formations, an analysis was made of all .own conditions that influence flooding.

Jan 1, 1941

Jan 1, 1987

Computer applications are ideally suited to the day to day operations of grade control and short term planning on a mine site. By refining this part of the operation there is scope to increase profits by more accurately predicting ore grade and tonnage, and allowing the mining engineer more flexibility in his approach to scheduling. Large numbers of blasthole or ditchwitch samples need to be processed in a fast and efficient manner, and stored in a database for future reference. The mining engineer has to calculate tonnages and subdivide the blast or digging area into mineable areas of waste, low and high grade ore. New grade and tonnage information must be used by the mining engineer to update his short term plan. Answers must be obtained quickly and efficiently, but a high level of individual input is necessary in order that maximum use is made of the information. Geostatistical analysis of samples can be used to refine the interpolation techniques. Reconciliation between the original grade model, the newly sampled area, and the final product should be monitored continually.

Jan 1, 1989

By Michelle Stokes, Alexandra Miller, Campbell McKenzie

"The ancestral Ringarooma River in northeast Tasmania has transported alluvial tin and other heavy minerals from their onshore source of stanniferous Devonian granites downstream into what is now Ringarooma Bay. Previous exploration work has demonstrated the presence of potentially economic tin mineralisation within the palaeochannels and terraces associated with the submerged river.The offshore tin resource lies directly on the seabed or with less than 2 m of overburden, and within 5 - 50 m water depths in the wider bay area. The main river channel continues offshore for at least 13 km, with high tin grades found within the palaeochannel but also dispersed across the sea floor as a sheet wash, a result of Quaternary sea level change reworking the placer deposits. This drowned portion of the coastal plain contains a continuation of rich tin leads as low gradient anastomosing channels, and has been delineated by marine seismic and drilling activity since the 1960s. Tin grades in the Tertiary and Quaternary alluvial profiles vary from 50 - 300 g/m3, with the highest concentrations in the coarser basal horizons. A previous offshore explorer estimated a resource of 194 Mm3 at 150 - 250 g/m3.Kenex Ltd created 3D models of the paleochannels and the mineralisation with the aim of better constraining the resource estimate and identifying additional depositional areas. The modelling was undertaken with the input of geophysical data, bathymetry and geochemical sampling of the seabed surface and from historic offshore drill holes. A prospectivity model covering Ringarooma Bay was produced to target tin-bearing gravels. Predictive maps were created to represent various features of the offshore mineral system, including assessing gradient changes in palaeochannels and their sinuosity. The model identifies areas with higher potential for alluvial tin mineralisation and will be used to focus the exploration programme over tenements currently held by Kenex Ltd."

Sep 1, 2014

By Stanley A. Schwartz

In the Piedmont, heavily loaded structures are generally supported by either drilled piers or one of several pile types. The choice of drilled piers or piles is typically one of comparative costs. The cost of a drilled pier foundation is usually the more difficult to predict because of the greater impact that variable conditions and construction monitoring have on cost. Poor specifications, related to the drilling equipment, procedures and bearing level, can also result in large cost extras. In the southern Piedmont, straight shafts are typically extended down to hard rock to achieve primary support in end-bearing: when bells are required, they are often constructed manually. In some eastern and northern Piedmont locations the thickness of the decompossed rock zone is significant and considerable skin friction can be mobilized. Typically piers are constructed in holes temporarily cased with steel liners. The bottom is cleaned of loose material and water, and then evaluated by a geotechnical engineer to confirm the design bearing pressure (and friction, where appropriate) or recommend alternative construction measures.

Jan 1, 1988

By A. H. Swart

Unplanned stope panel collapses occur on most near-surface and shallow mines in South Africa. Although these incidents often occur during blasting, they pose a major threat to the safety of underground workers and the economic extraction of orebodies. Most stope panel collapses occur due to excessive panel lengths (resulting in excessive stope spans) that are not designed according to a systematic design procedure or methodology. Instead, panel lengths are often dictated by the equipment in use and by previous experience under similar conditions. Hence, a rock engineering design methodology for the design of stable stope panels between pillars is of vital importance for optimum safety and production in shallow mining operations. Using the proposed design methodology described in this paper, rock mechanics practitioners and mine planners should be able to identify and quantify the critical factors influencing the stability of stope panels. The critical factors should then be used as input to the design of stable stope panels that will provide the necessary safe environment for underground personnel working in stopes. The proposed design methodology is an iterative process, which includes aspects such as rock mass characterization, estimation of rock mass properties, identification of potential failure modes, consideration of appropriate stability analyses and other elements of the rock engineering design process. This process continues after implementation. During monitoring, new data should be included in the database and the design process repeated on a regular basis. Design approaches included in the proposed design methodology include empirical methods such as different rock mass classification methods, analytical methods such as elastic and Voussoir beam analyses, kinematic analyses, probabilistic analyses, and numerical analyses. Keywords: stability, stope panels, design methodology, hardrock mines, shallow mining operations

Jan 1, 2005

Solid. dense, air-cooled slag can fulfil most, if not all, the functions of natural stone for civil engineering purposes. The value of pumice, also, has long been appreciated, and processes for the manufacture of similar synthetic material for light-weight concretes and insulating fills have been developed in past years.Foamed slag is, in effect, blast furnace pumice and is often referred to on the European continent as metallurgical pumice. It is made by the treatment of molten blast furnace slags with a critical quantity of water during which process the slag cools and expands into a sponge-like mass. The connection between foamed slag and air-cooled slag is also considered and a basis for density control given.All blast furnace slag cannot be foamed to give a product which would comply with B.S.S.877; 1939 Foamed Blast Furnace Slag. A large proportion of the total output of molten slag lacks the necessary inherent properties. This investigation attempts to discover the conditions necessary for the production of foamed slag capable of meeting the British specification.EARLIER WORKIt was generally accepted (Parker, 1951; Gallai-Hatchard, 1955) that the spongy structure of foamed slag was caused mechanically by steam trapped in the slag when it was poured into water. It was assumed that slags which would not foam would not trap steam, because their viscosities and surface tensions were unsatisfactory, on account of temperature and/or composition. The earliest systematic investigation was made by Frisak (1923) who attempted to establish a limiting chemical composition for foamable slags. He decided that foamable slags covered most blast furnace slag compositions on the basis of silica, alumina, and lime, and further "that the replacement of lime by magnesia up to 15 per cent has no noteworthy effect on foamability, that moderate quantities of alkalis are not deleterious, that sulphur raises the foamability and that MnO is only deleterious in the presence of 1...

Jan 1, 1963