Search Documents

By Paul M. Tyler

MUCH has been said in print, and much more that was unprintable, about burdensome controls, taxation, and multiplying restrictive, regulatory, or taxing activities of the Federal Government, but not so much has been said about ways and means whereby the Government can and does render economic assistance. Economics has been defined as the study of men earning a living, and economic assistance to industry as well as to individuals properly should take the form of helping enterprisers to help themselves rather than charity. Proposals to have the Government play Santa Claus must be examined carefully if -only to avoid undue favoritism to politically important persons and downright venality by potentially crooked public officials. Thomas Jefferson is credited with the remark that the best government is the one which governs least. Paternalism is abhorrent to most Americans.

Jan 1, 1947

By H. Akbari

Ordinary portland cement (OPC) is the key pozzalonic component of the concrete mix widely used as a construction material worldwide. B illions of tons of OPC are used in the construction industry each year. However, calcinations of limestone and silica that produce OPC also produce almost an equal amount of C O2 during the cement manufacturing process. Thus, OPC production accounts for nearly 7% of all anthropogenic C O2 emissions each year. The main objective of this study was to develop a geopolymer-based composite to be used as a substitute for OPC in concrete application to significantly lower the carbon footprint of the construction industry. A waste material produced during the coal combustion process was used as the main raw material for the geopolymer-based composite. It was mostly the nonmetallic content of the F-type fly ash produced from the combustion of bituminous coal. The authors envisioned extracting some of the valuable metal oxides from fly ash prior to using the major nonmetallic portion of the fly ash for geopolymer concrete application. The results obtained from this study showed that the compressive strength of geopolymer concrete compares favorably with that of conventional concrete prepared using OPC.

Dec 1, 2013

By Robert Thurner

The underground car park "Admonterhof in the historical centre of Graz is an example for the technical and economical success of a complicated structural design using a concept on the basis of the observational method. The intention to built a 20 m deep excavation beneath a protected monument was accompanied by some essential issues: the preservation of the existing state avoiding extensive displacements by means of a girder grid of reinforced concrete, its support on large bored piles and small steel-tube piles with possible active compensation of differential settlements, the excavation support in none built-up areas with secant bored piles, the underpinning of existing buildings with different structures by means of jet grouting. Furthermore the hydraulic gradient and the permeability of a rock formation in a part of the excavation had to be explored with the purpose to control the inflow of groundwater with a level difference of more than 10 m.

Jan 1, 2006

By AIME AIME

THE twenty-second annual meeting of the Canadian Mining Institute was held at the King Edward Hotel, Toronto, on Mar. 8, 9, and 10, and was followed on the 11th by an all-day excursion to the International Nickel Refinery at Port Colborne. The meeting was very well attended and dealt with some of the most important matters, both technical and economic, that have ever come before the Canadian Institute. The question of licensing engineers is before the Canadian members as it is before our own in this country and the attitude of the mining engineers across the border is like that of the American mining engineers, opposed to the licensing of the mining. engineer, however they may feel toward the licensing of other branches of the engineering profession. It was well pointed out that such a law, had it been in existence in the last decade or two, would probably have prevented the rapid development of Canada's mines. Whereas one civil engineer can run a line of survey as well as another, perhaps, it is only a question in his case of whether he can or cannot survey. In the case of a mining engineer employed by a man with capital to invest in a development project, unless the man with the money has confidence in the judgment of his engineer the fact that he is a professional man would carry little weight in inducing a large investment toward the development of Canada's resources. It was also pointed out that although the Institute as a whole had not passed on the matter, it would probably be opposed to legislation aiming only for self-interest, but would be heartily in accord with legislation which could be shown to be for the service of the community at large.

Jan 1, 1920

By C. M. McCulloch

A geologic study of Mines 32 and 33 in Cambria County, Pa., was conducted as part of a methane control research program. Areas of high methane emission and roof instability are encountered which are related to the structural and stratigraphic features that characterize the geologic setting of these mines. Locally the folds trend N 20° E ±2°, the direction of the butt cleat in the Lower Kittanning coal. The face cleat strikes at N 69° W ±2° and the systematic rock joint in the surface bedrock strikes N 67° W ±2°. This suggests that a directional stress oriented N 70° W produced the folds and influenced the directions of coal cleat and systematic joint sets. Analysis of SLAR indicates three directions of prominent regional lineation: N 39° E, N 31° W, and N 70° W. Little gas was encountered during development mining; large volumes of gas are encountered when roof falls. Most of the gas comes from strata above the mined coal; therefore, to control methane, roof instability must be controlled. Roof falls and high rates of methane emission are most likely where less than 30 feet of many thin layers of limestone, shale, and sandstone occurs between the Lower Kittanning coal and the next coal and in zones along the margins of a sandstone channel.

Jan 1, 1973

By E. D. Gardner

Ore and concentrate are transported on, the surface at western mining districts by (1) railroads, (2) surface trams, (3) aerial trams, (4) trucks, and (5) wagons, and (6) on the backs of animals. The daily and ultimate tonnage to be moved is the principal factor governing the selection of the method of transportation. Railroads are preferred when large tonnages are to be hauled over relatively long distances. The mine-haulage system may be extended or surface trams built to the mill or shipping point if a practical track grade is possible and if the distance is relatively short. Aerial trams have a special field of usefulness for transportation over steep or excessively rough terrain.

Jan 1, 1936

By Bernard Lewis

This report summarizes fundamental research end technical studies conducted in the Explosives and Physical Sciences Division, Region VIII, of the Bureau of Mines in the 2 years July l, 1950, to June 30, 1952. It is the fifteenth of a series of, ordinarily, annual reports whose aim has been to provide the reader with a resume of the research results that have appeared in published form during each fiscal year under the authorship of members of the staff. These are referred to throughout the report. ACKNOWLEDGMENTS Acknowledgments art, made to the following members of the Division wider whose mediate supervision the described studies were carried out. Stuart R. Brinkley, Jr., chief, Mathematical and Theoretical Physics Section, and special assistant to the chief of the division.

Jan 1, 1953

By J. E. Hoffman

The operation of the U .S Metals Refining Company, USMR Co. is defined below by the description of a variety of unit processes and operations the author encountered during his tenure with the operation, 1955 - 1978. The operations discussed include: sampling and sweating of radiators, processing of Indian Coin, treatment of insulated wire, baghouse and converter dust treatment, blast furnace and converter operation, the electric arc furnace, antimony control, selenium and tellurium products, electrolyte liberation with soluble anodes, and the precious metals refinery. These operations, although peripheral to the primary copper production circuit, were critical to the company's technological and economic base.

Jan 1, 2000

Jan 1, 1882

By D. A. Barr

High-grade gold-silver mineralization associated with electrum and argentite was discovered in a quartz vein at the Chappelle property, 273 km north of Smithers, B.C., in 1969 following a regional geochemical reconnaissance program in the Cassiar-Omineca Mountains. Subsequent exploration resulted in the discovery of numerous quartz veins with associated precious-metal values in a belt 17 by 3 km in area centrally located within Toodoggone Group volcanic and sedimentary rocks of Lower to Middle Jurassic age and a window of Takla Group volcanic rocks of Upper Triassic age. More detailed investigations, consisting principally of 5677 m of surface drilling in 57 holes and crosscutting, drifting and raising on Chapelle Vein A, has outlined a high-grade gold-silver-bearing shoot with a strike length of 200 m, an average width of about 3 m and extending to an average depth of about 40 m below surface.

Jan 1, 1978

By J. J. Jakosky

THE method of electrical mapping of oil structures to be described possesses certain limitations, as well as certain definite advantages. It, in common with other geophysical methods, is not a panacea for the solution of all subsurface geological problems. It operates on differences in electrical conductivity of the geological strata, whereas the other most-used methods operate on (1) differences in magnetic properties, (2) differences in gravimetric properties, or (3) differences in seismic properties. This modification of the resistivity method is therefore able to obtain subsurface information under conditions not favorable to the other methods mentioned. Where the other methods have been employed with ambiguous results it may act as a complementary method.

Jan 1, 1936

By W. A. Gibson, A. D. Trujillo

The Santa Rita copper deposit first served as a source of native copper for Indian implements and weapons. In 1801 Santa Rita copper, trans- ported by mule train to Chihuahua, began to be used commercially for making coins. It was a small- scale operation made difficult by Indian raids, transportation costs and depletion of the higher grade ores. There was, moreover, no known method for economically extracting copper from the under- lying low grade sulfide ores. Originally, copper and copper oxide ores were mined by underground methods, but there was virtually no development of the deposit-which became United States territory after the Treaty of Guadalupe Hidalgo in 1848-for almost a hundred years. A number of small underground mines had been started during that time, but it was not until 1873 that all the principal claims were consolidated under one control.

Jan 1, 1966

By Dupuy. Leon W., R. T. C. Rasmussen, W. A. Calhoun

"INTRODUCTION For many years it has been known that low-grade manganese deposits occur in the bluffs along the Missouri River Valley. Frequent attempts have been made to develop the ore and to produce a marketalble commodity but they have had little success. Under pressure of the war emergency and the shortage of manganese, the attention of the Federal Bureau of Mines was directedtoward the deposits.Manganese-bearing shale occurs from a point near Pierre, S. Dak., down the river to the Rosebud bridge near the Nebraska line (1).5/ The Bureau of,confined its work to the more accessible central portion of the deposits near Chamberlain, S. Dak. The ore occurs principally as concretionary nodules in the form of iron and manganese carbonates (manganosiarite and perhaps some manganocalcite; rhodochrosite has not been identified). At the surface the carbonate is often broken down so that the oxide of manganese gives the nodules a black The matrix or host rock is generally known as Pierre shale, composed of ""interbedded layers of bentonite, an altered volcanic ash, and dissemi¬nated bentonite particles,"" (2) and montmorillonite-beidellite clay minerals (3). The shale weathers to the very sticky gumbo characteristic of South Dakota and well-known to hunters and travelers in the area.The area selected for the experimental mining and pilot-plant work discussed in this report lies about 8 miles westerly from Chamberlain and is a few hundred feet north of U. S. Highway,16, on land owned or controlled,by M. Q. Sharpe of Kennebec, S. Dak., and the General Manganese Corp."

Feb 1, 1946

By A. Pellegrino, F. Collin, C. Guiducci, R. Charlier

A numerical approach for modeling coupled Hydro-Mechanical fracture behavior in 2D is presented in this paper. This approach accounts for the strong dependence of the flow characteristics on fracture apertures and offers an anisotropic description of the flow propagation in the fracture. An interface finite element and a constitutive model are developed . In order to validate the applicability of the model to general geomechanic problems, 2D simulations were performed. Results show the good application of the mathematical model and the fundamental hydraulic role played by the fractures. In diesem Beitrag wird ein Stoffgesetz vorgeschlagen um hydromechanisches Kluftverhalten numerisch zu Modellieren. Dieser Vorgang nimmt die starke Abhängigkeit der Fliesseigenschaften von der Kluftöffnung mit in Anbetracht. Ein Interfaceelement und ein Stoffgesetz wurden entwickelt. Zum validieren der Anwendbarkeit dieses Modells wurden 2D Simulationen durchgeführt. Ergebnisse haben gezeigt dass das mathematische Model anwendbar ist und dass Klüfte eine fundamentale hydraulische Rolle spielen. Une approche numérique pour la modélisation du comportement couplé hydro-mécanique des fractures en 2D est présentée dans ce papier. Cette approche prend en compte la forte dépendance des caractéristiques du flux de fluide sur les ouvertures des fractures et présente une description anisotrope de la propagation du flux dans la fracture. Un élément fini d'interface et un modèle constitutif sont développés. Dans le but de valider l'applicabilité du modèle à des problèmes généraux de géomécanique, des simulations 2D ont été réalisées. Les résultats montrent la bonne application du modèle mathématique et le rôle hydraulique fondamental joué par les fractures.

Jan 1, 2003

By Hernán Parra

Las pruebas cerradas de flotación (ICFT) son necesarias para el diseño de plantas a niveles de prefactibilidad y factibilidad, ya sea en proyectos greenfield o brownfield. Estas pruebas se realizan después de haber hecho un estudio previo de flotación batch y se usan para simular un circuito continuo. En este trabajo se reseñan los estudios sobre el tema, se busca establecer la manera adecuada de ejecutar la práctica de laboratorio y de evaluar los resultados experimentales, con el propósito de introducir mejoras en el diseño de plantas.

Aug 30, 2017

By Craig Hartley

? A helper stands beside a continuous miner as the operator is at the controls. The operator means to push the stop button but hits the drum rotation start button by mistake. The drum begins to turn and the bits catch the helper's clothing. He is thrown violently to the ground and suffers multiple contusions. ? A farmer's wife helplessly watches her husband drawn into the claws of farm machinery while she frantically and unsucessfully searches for the control to stop the machine. ? A mechanic on the night shift replaces plugs in the lubrication systems of all three engines of an airliner following routine maintenance. In doing so', he fails to notice that "0" ring seals have not been mounted on the plugs. A few hours later, as the fully loaded airliner is cruising high over the ocean, oil pressure on one engine drops precipitously. The pilots quickly shut down the engine and turn for home. Almost immediately, the two remaining engines lose their oil and fail.

Jan 1, 1983

By Christopher Haycocks

Because of growing pressure from government and consumers to produce more coal, the mining industry must improve existing techniques and devise more efficient mining methods. Mining of the thicker, shallower and geologically superior coal seams in the western United States is being subjected to increasing pressure from environmentalists; and so in order to meet the demand, the coal industry is exhausting the more accessible surface seams and beginning to mine seam of over 1,000 feet in depth and less than. 30 inches in thickness. The longwall mining system is the natural choice for extracting deep and thin coal seams, as it operates almost independently of the overburden rock stress. Due to the added fact that longwall mining is an inherently more productive method than room and pillar mining, many coal producers are looking to it as a means of increasing productivity without a corresponding cost increase. The consistent rise in application of longwall mining in the United States in the last decade illustrates the excellent potential of this technique for the future. American mining conditions are geologically different from those in Europe where longwall mining has been highly developed and extremely successful. Although numerous successes have been recorded in the U.S. with this mining system, a substantial number of failures have also occurred. These failures are due primarily to roof control problems usually over the face, in the tail entry, or both. Another problem area for American operators contemplating the use of this method has been correct selection of equipment, which should be custom fitted to local mining conditions for optimum productivity. It is essential that correct estimates for chock resistances, support densities, supported and unsupported roof spans, as well as rates of advance and length of working faces be provided to optimize mining conditions. Unless extensive pilot projects are planned engineers must choose their equipment correctly at the outset. A typical investment in longwall equipment will amount to several millions of dollars.

Jan 1, 1979

By Peter K. Kaiser

Planning and design of deep underground mines involves a process of complex three-dimensional data integration utilizing information from exploration (geology, rock mass characteristics), engineering (mining method, excavation geometry, stress) and operations (time, in the form of sequencing). As new logging and monitoring technologies are being developed, the amount and data complexity becomes overwhelming and decisions are often made based on only a small part of the available data. Recently, Laurentian University opened a state-of-the-art Virtual Reality Laboratory (VRL), a Mining Exploratorium that is unique in the world of mining and offers an exceptional data interpretation environment for mine planning and design. The Mining Exploratorium combines a large format spherical stereoscopic projection system, equipped with high definition projection providing the highest resolution of active stereo in the world today, with advanced features of earth modeling software. Combined, this creates the first virtual reality facility geared specifically to the interpretation of mine geometry, geology, geochemistry, microseismicity, geomechanics and mining data sets. This paper demonstrates how value can be added to the mine planning and design process by utilizing this unique tool in the mining decision-making process via better comprehension of spatial relationships of data and by interpreting the data in a collaborative immersive virtual reality environment.

May 1, 2002

By R. E. Murray

"It is a gloomy moment in the history of our country. Not in the lifetime of most men has there been so much grave and deep apprehension; never has the future seemed so incalculable as at this time. The domestic economic situation is in chaos. Our dollar is weak throughout the world. Prices are so high as to be utterly impossible. The political cauldron seethes and bubbles with uncertainty. Russia hangs, as usual, like a cloud, dark and silent, upon the horizon. It is a solemn moment. Of our troubles, no man can see the end." By now you, no doubt, are asking, 'Where did Murray get this bit of philosophy?' Well, I obtained it from an editorial entitled. "The Worst of Times", which was published in the Harper's Magazine in 1847. That's right, 1847! The parallelism between the situation in our country at this time and in 1847 is un- canny. But wait, there is one major exception the size of government. To my knowledge, the citizens of 1847 were not stifled by the extreme governmental excesses that we are experiencing today.

Jan 1, 1980

The U.S. Bureau of Mines has been concerned for many years with the general problems of underground coal mining and the particular problems due to the methane content of the coal. The Bureau and others have worked diligently to improve the health and safety conditions for underground coal miners. It has been recognized for many years that the methane in coal would have some value if it could he recovered and used, Also its removal before coal mining began or during the mining cycle itself would make mining safer and more economic due to a potential saving in ventilation costs. The work covered in this report was carried out to review methods of removing methane from active and inactive regions of operating coal mines and to determine how the methane could be concentrated and utilized economically.

Jan 1, 1975