Search Documents

By Steven Wright

The extent and the rate of reduction of slags produced from the smelting of recycled lead batteries were investigated under laboratory conditions using graphite as reductant. Simultaneous reduction of PbO, Fe2O3, Sb2O3 and As2O3 occurred at temperatures of 1180 and 1200°C, with Sb and As reporting to the metal phase while the PbO content of the slag was above 2 wt%. Fuming of As from the metal occurred at lower concentrations of lead in the slag. Discard slags with low levels of As, Pb and Sb were produced. Arsenic levels were reduced to less than accurately measurable by ICP analysis, and Sb levels in the final slags were in the range of 0.1 to 0.2 wt%. The kinetic data obtained were analysed and compared with other measurements on lead oxide containing slags. The results showing a dependence of the reduction rate on the oxidation state and the basicity are consistent with other studies on well characterised industrial and. synthetic lead slags. These results indicate that when carbonaceous reductants are used, the rate of interfacial reactions play an important role in enabling the production of environmentally acceptable discard slags.

Jan 1, 1994

By Daniel Chen, Jewel Andrew Gomes, Venkata Palla, Sadia Afrin Jame, David Cocke, Paul Bemazzani

"Textile industries use various kinds of chemicals including dyestuffs and pigments during dyeing and finishing processes. The effluent from these processes includes suspended particles, strong color, high pH and high chemical oxygen demand (COD) that are extremely toxic and make environmental hazard. Although physical, chemical, photochemical, and biological methods are available for treating such wastewater, the electrochemical technique, electrocoagulation (EC), has emerged as an efficient, simple, and cost-effective technology in the last few decades. In this study we present the applicability of EC technique for removing dye, such as direct red dye using iron electrodes, and the optimized conditions such as dye concentration, current density and pH. The degradation of dye molecules was investigated using UV-visible spectroscopy. The EC-floe was also characterized using SEM/EDS, XRD and FTIR.IntroductionWastewaters generated by textile industries contain large amounts of toxic aromatic compounds, especially azo dyes. Azo dyes and their degradation products, such as aromatic amines, are highly carcinogenic. These effluents are also responsible for causing high levels of color. The colored wastewater released into the environment is also a source for disruption of aquatic life and aesthetic pollution as well [1].In most textile industries, dyeing and finishing are the two important processes which are generally applied. These two common processes generate significant amount of wastewater, which may contain, suspended particles, high pH, strong color and high chemical oxygen demand (COD) concentration [2]. Low pH and high temperature are other polluting factors from the waste water. Textile industries make use of about 10,000 dyes and pigments [3]. Disposal of these colored wastewaters poses a major problem for the industries as well as a threat to the environment. In textile industries, because of the low efficiency (60-90%) of dye fixing on textile fibers, substantial amounts of unfixed dyes are released in waste waters. The conventional method for treatment of textile wastewater was a combination of biological, physical and chemical methods [2]."

Jan 1, 2011

By Jiang Diao, Yong Qiao, Xuan Liu, Tao Zhang, Bing Xie

The equilibrium experiments between the FeO-SiO2-MnO-TiO2-V2O3-Cr2O3-MgO slag system and solid pure iron were performed to investigate the vanadium and chromium distribution ratio under Ar atmosphere. The influence of w(FeO), w(V2O3) and w(Cr2O3) in slag on vanadium and chromium distribution ratios were studied at 1653 K. The experimental results were compared with calculated distribution ratios based on molecule and ions coexistence theory. Both of them showed that higher FeO content in slag would improve the distribution ratios of V and Cr between slag and hot metal. The distribution ratio of Cr or V increased with the increase of Cr2O3 or V2O3 content, respectively. To optimize the oxidation of V and Cr from hot metal, a high oxidizing slag and suitable content of Cr2O3 and V2O3 in the slag were recommended. The results provided reference for the further study on the extraction of V and Cr in VTi magnetite.

Jan 1, 2016

By Robert W. Bartlett

Biooxidation of an ore heap containing only a few percent of sulfide minerals requires insertion of a very large amount of oxygen either by natural air convection, forced air ventilation or gaseous diffusion. While shallow heaps, those with lateral distances much greater than their height, are of great interest for many heaped ore processing operations, natural convection is often ineffective for oxidizing them because of inadequate lateral flow into the heap's interior. Oxygen can diffuse into a shallow heap from its upper, horizontal surface in contact with air. Oxygen diffuses through the air-filled void space within the heap, driven by the oxygen concentration gradient resulting from internal oxygen depletion caused by mineral oxidation. Oxygen diffusion, coupled with the chemical reaction kinetics oxidizing the sulfide minerals, is analyzed for conditions of rapid mineral oxidation kinetics, requiring small mineral grain sizes, and for typical ore heap biooxidation parameters. Practical limits on heap heights are presented for effective biooxidation of the sulfide minerals within times of interest for heap biooxidation of refractory sulfide gold ores, one to three years.

Jan 1, 1995

By Milton Syamujulu

In 2004, KCM Nkana Smelter commissioned a 1200 tonne per day flash dryer and associated dry concentrate transport and injection system on the existing Teniente Modified converter (CT) unit. The aim was to upgrade the existing smelting unit, increase copper output and improve energy efficiency. This paper reviews the design, installation and commissioning phases of the introduction of this new technology and also discusses the initial two years of operating results for both the flash dryer and injection system at Nkana.

Jan 1, 2006

By Matsufumi Takaya, Yukihiro Sakamoto

"Electric field emission properties from CVD diamond fabricated using pulse-modulated microwave plasma CVD were studied. Diamond was synthesized by microwave plasma CVD apparatus equipped with a pulse-modulated microwave power supply. Pulse conditions were varied from 1 to 10 seconds for pulse periods and from 0.1 to lHz for pulse frequency either. Surface morphologies of the deposits were differed by pulse frequency and duty cycle. As a result, FE properties prepared by different pulse duty cycle were different from continuous film which synthesized using continuous microwave significantly. Highest current density was obtained from the uneven morphology diamond film prepared at 17.5% pulse duty cycle.FE properties of the CVD diamond were depended on surface morphologies that related to the pulse conditions.1. IntroductionDiamond has excellent physical and chemical properties as an industrial material. Especially, hydrogen terminated diamond had the negative electron affinity (NEA) 1) and CVD diamond has this NEA property either as deposited 2). So the electron emission source to the FED is expected as one of this application of CVD diamond as cold cathode of electric devices. We studied on FE properties of various CVD diamond, pulse microwave plasma CVD diamond showed better property than those of other CVD diamond 3).This report studied on· the effect of the duty-cycle of pulse modulate microwave condition on FE properties of the diamond fabricated by pulse modulated microwave plasma CVD."

Jan 1, 2000

By Onwukamike, Onyedika G. O, Ogwuegbu M. O. C., K., Onyenehide C

A detailed mineralogical and elemental characterization of a lead (Pb) ore deposit from Ishiagu, Ebonyi State, Nigeria was carried out with XRD, SEM-EDX, and ICP-OES based mappingtechniques. The results show that the most dominant and valuable metal is lead (Pb = 95.02%, mass fraction). The main mineral is galena. Ilmenite and sphalerite occur as minors, which account for 2.71% and 0.80% respectively. Elements like Al, Ca, Mg, Ti, Na, Mn, Si and Sn occurred in trace amounts and are disseminated in the entire ore body.The surface and interrelations of the crystals were examined with x-ray mapping and the result shows the pattern of dissemination of the minerals within the ore body.

Jan 1, 2015

By Jun-ichiro Yagi

A mathematical model has been developed for simulating the blast furnace operation with carbon composite agglomerates charging based on multi-fluid theory and reaction kinetics. In this model, the behaviours of carbon composite agglomerates are considered on the basis of previously reported conservation equations and experimental research on the reduction rate of carbon composite agglomerates. A series of calculations are performed to examine the effect of charging carbon composite agglomerates. The model calculation gives two-dimensional distributions of process variables and information on the overall operational parameters. It reveals that in-furnace temperature levels significantly decrease and the reduction of carbon composite agglomerates is retarded with carbon composite agglomerates charging ratio. The furnace performance is remarkably improved with the increase in carbon composite agglomerates rate. The productivity tends to increase while coke rate and total reducing agent rate show decreases at the different degree.

Jan 1, 2006

By Chunlin Chen

Published data on thermodynamics of a number of minor elements (As, Sb, Bi, Pb, Zn, Se, Te, Cr, Sn) in liquid copper, matte and slag have been reviewed, assessed and used in development of thermodynamic solution models of melts. The behavior of antimony in alloys, mattes and slags is used as an example to illustrate the approach taken in assessment of published data and validation of the developed models with respect to the activity of Sb in condensed phases as well as the effects of matte grade, slag chemistry, temperature etc on the equilibrium distribution of Sb between melts and the gas phase. Results obtained from a comparison of different smelting processes with the modeled multi-phase equilibrium are presented and discussed. The predicted effects of slag chemistry and matte grade on the deportment of other minor elements during smelting of copper mattes will be presented and discussed.

Jan 1, 2006

By M. Misra

The volume of low-level contaminated soil at the. Department of Energy's Nuclear Weapon Sites are in the order of several million tons. Most of the contaminants are uranium, plutonium, other heavy metals and organic compounds. Selected Physical separation processes have shown demonstrated potential in COD Centratingthe radio nuclides in a small fraction of the soil. Depending upon the size, nature of bonding and distributions of radio nuclides, more than 90 percent of the radio nuclide activity can be concentrated in a small volume of fraction of the soil. The physico-chemical separation processes such as flotation in a mechanical and microbubble tall column cell have shown, promising applications in cleaning up the high volume contaminated soil.

Jan 1, 1995

By Abhishek Lahiri, Animesh Jha

"A new technique for the selective separation of rare earths and impurities from lower grade titaniferous ores has been developed which will reduce the overall reduction in the energy costs, and therefore the CO2 generation by at least an order of magnitude during the chlorination and waste handling stages of TiO2 to TiCl4 reaction. The process includes roasting the ilmenite ore with alkali followed by water washing step, which removes nearly 80% of oxides of lanthanide and actinide elements present in lower grades of titaniferous minerals. In the context of preferential separation of rare- 3+ + earth and actinide oxides, we have examined the roles of Al and K ions on the lattice structures of ilmenite and complex titanate as the product layer forms during the roasting in air in the presence of potash. The composition of the mixtures of oxides derived from the separation process shows that the mixture of rare-earth oxides m ay be a high-value co-product of the overall beneficiation process.IntroductionWorldwide the production of synthetic rutile is carried out either by the sulphate or the slag-making followed by fluidised bed chlorination of TiO2 enriched slag granules. The chlorinated gas is then re-oxidized to make white pigment grade TiO2. The waste generated by the sulphate process is predominantly iron sulphate, which has limited use in the water treatment plant. The remaining wastes from the sulphate process undergo further treatment using filtration followed by evaporation and thermal decomposition after which it is disposed into deep sea. On the other hand the chloride waste is extremely hazardous and requires special case by neutralisation, followed by impoundment in a managed pond, where it is monitored for long-term for potential contamination to the soil and ground water. Rare-earth and prelanthanide wastes often end up in the pond where they are diluted and irretrievably lost for further use or recycle. Certain parts of the world the chloride process wastes are pumped via deep boreholes into porous geological strata. The present techniques of disposal are not only expensive but also pose continued threat groundwater and soil and marine life in case of sulphate waste [1, 2]."

Jan 1, 2009

By Toshihiro Kuzuya

A hydro metallurgical process has been developed for the recovery of metal values such as Co, Ni and rare earths from the electrode materials of spent nickel metal-hydride(Ni-MH) secondary battery. MmNis_xCo. (Mm : Misch metal) intermetallic compound could be separated from the electrode materials mixture by sedimentation. A typical chemical composition of MmN5-xCox was approximately, in mass%, 56.0%Ni, 13.4%Ce, 10.6%La and 7.9%Co. The time dependency of leaching intermetallic compound with sulfuric acid solution was examined with processing factors such as sulfuric acid concentration, temperature and agitation intensity, The leaching of rare earth metals proceeded very rapidly, reaching completion in less than 1.8ks. On the other hand, the slow leaching of nickel was observed. The percent of nickel leached at 328K could only reach about 70%.

Jan 1, 2003

By Juha Järvi

Outokumpu Zinc Oy has two separate roasting lines with fluidized bed furnaces and waste heat boilers for calcine collection and heat recovery. During the last 30 years, zinc production in Kokkola plant has increased continuously and at the same time the raw materials have changed. Therefore, the waste heat boiler has been under continuous research and development. The waste heat boiler plays a significant role in the process and consequently the reliability and efficiency of the device is important for the effectiveness of the entire process. Many changes have been made to the boiler in the last decades. New radiation tube screens, tube bundles, and baffle-plate constructions have been added to the boiler and also rapping systems for the dust have been developed. The latest improvement to the boilers was a baffle wall, located in the middle of the radiation section roof in the first boiler, and baffle plates in the lower part of the convection section in the second boiler. The new boiler design and optimization were carried out using physical water and air-dust modeling as well as computational fluid dynamics. The modeling work agrees well with experiences in practice. The latest developments have increased the operating hours per year and the effectiveness of the waste heat boiler.

Jan 1, 2002

By Toshiyuki Hiranami, Keizou Uematsu

"AbstractionSpray freeze drying method was proposed to fabricate ·ceramic: powder granules for high performance ceramics. Obtained granules and their green compact were characterized by SEM and immersion liquid technique. Granules have a spherical shape of about l 00 µ m in diameter, ·and no binder segregation was found with the immersion liquid technique. The granule had sufficient strength for usual handling, while the strength was much lower than that of granules prepared by conventional spray-drying. Unlike the conventional green compacts, granule interfaces were not observed in the green body made with the spray-freeze dried granules.IntroductionIt was well kn9wn that spray-dried granules have binder segregation layer on their surfaces. The trace of this segregation layer survives in the later processes i.e. compaction and firing, and behaves as fracture origins in the sintered bodies. The origin of this problem is solvent drying process from slurry droplet surface in spray drying system. As alternative method we propose a freeze drying process for granule preparation, in which solvent is remove by sublimation though the process, binder segregation can be prevent.In this study, we applied spray freeze drying method to fabricate alumina powder granule, and characterized the obtained granules, and their green compacts and sintered bodies.Experimental procedure.Alumina powders and additives aqueous solution were mixed for 24 hours using a ball mill to· prepare the slurry for spray freeze drying. .The solid loading of the slurry was 30vo1%. Deflocculant (PAA-NH4 type) was added 0.5mass%, and the binder (PVA). 1.0, 2.0 or 3.0mass% of alumina. Obtained slurries were sprayed into liquid nitrogen to make frozen granules. The granules were freeze dried.For the characterization of the granules, immersion, liquid technique observation and single granule strength test were carried out. Strength of individual granule wa5 measured using micro compression testing machine (MCTM, SHIMADZU). Granule strength was calculated from following equation."

Jan 1, 2000

By B. C. Curson

A comprehensive simulation of .the gas handling system in BHP Copper's San Manuel smelter was developed using AFT Fathom software, with the objective of minimizing SO2 emissions while maximizing smelter throughput. Once verified with plant data, the simulation quickly revealed' the complex interactions occurring between individual converters and the flash furnace. The increased understanding provided by the simulation allowed novel, counter-intuitive control strategies to be developed and tested successfully.

Jan 1, 1999

By Khosrow Nikkhah

Increasingly ion exchange systems are being included in design of hydrometallurgical plants for metal extraction or impurity removal. Because such systems operate sequentially and are based on resins that exchange one ion for another, store it temporarily and release it to a regenerating solution, the usual steady state heat and mass balancing tools and spreadsheets cannot be used to design them successfully. This paper outlines the role of dynamic simulation in design of ion exchange systems. Examples are given for use of dynamic simulation in design and investigation of equipment based on consideration of the effect of input criteria such as expected ion loading and elution profiles. The methodology for dynamic modeling using IDEAS in design of multi column ion exchange trains operating in parallel is presented. Results shown include the non-steady state distribution of extracted metal and limitations imposed on operating conditions. These conditions include proposed sequencing of columns for loading and elution cycles, loading, elution and recycle flow rates as well as size and choice of related ion exchange plant equipment.

Jan 1, 2003

By Andreas Weber

Batrec operates a plant for the recycling of used dry batteries with a capacity of 3000 tons per year. The plant Is situated In a tourist area of Switzerland and has complied with all the strict emission restrictions. The process yields four products: FeMn. Zn, Hg and slag. No hazardous waste Is produced. All types of batteries can be treated.

Jan 1, 1995

By V. Bhagavathy

This paper describes a method for the determination of traces of rare earths using energy dispersive x-ray fluorescence spectrometry (EDXRF) after preconcentration of their oxine complexes onto activated carbon. Various parameters that influence adsorptive preconcentration of rare earths onto activated carbon viz. pH, amounts of activated carbon and oxine, time of stirring and aqueous phase volume were systematically studied. A numerical method based on simple least square procedure using fifth order polynomial with 25 consecutive values was developed for smoothing and differentiation of EDXRF data which was previously digitized and averaged. First order derivative EDXRF in conjunction with adsorptive preconcentration on activated carbon enables to determine as low as 10 ppb of each of individual rare earth elements.

Jan 1, 1989

By Jiu-ju Cai, Wen-caho Liu, Fei Liu

"With the northern cities of China as study objects, and to confirm Ground-source heat pump system of the environmental benefit and the developing direction. In this paper LCA was applied to the environmental benefit Ground-source heat pump System from raw materials acquisition to system production, utilization and disposal. The conclusion shows that Ground-source heat pump system of the environmental benefit in the northern cities of China. The result showed that Ground-source heat pump system had remarkable environmental benefit. 1. Introduction Life cycle assessment Originate in the sixties of last century, what it paid close attention to is to obtain processing from products raw materials, the processing of products produces, products transportation, products use and maintain to the influence to environment of course. It is a products -oriented environmental management style, it is the environmental management mode of meeting the needs of sustainable development strategy [1]. The research object was in the city and lie in the North of China, would undertake Beijing Olympic Games some football matches in the second half of 08, in order to improve the local environment, adjust the energy structure, reduce the heating consumption of urban coal in the centre, eliminate the coal-burning boiler under 10 tons, since 2005, the local government promotes and utilizes actively the heat pump technology in the source substitute the heating of coal-burning boiler. At present, this area is adopted the technological heating area of heat pump of source reach 20 million square meters, account for this area heat 11.2% of area always, it is estimated, by 2010, adopt the technological heating area of heat pump of source will reach 65 million square meters, the proportion of the area rises to about 30% to account for this area and always heat [2 ]. Study to the whole lifespan of heating system of heat pump of ground source of this area on the basis of LCA method, obtain the products impact on environment of different stages and environmental benefit, find out and reduce or dispel the measure of the influence, improve the environmental benefit of the ground source heat pump heating system.2. MethodologyThe research approach used in this research is the Life cycle assessment, the frame of the research approach is goal and scope definition, the inventory analysis, impact assessment, interpretation.[3][4][5]"

Jan 1, 2008

By M. Urda-Kiel

Stainless steel is increasingly used as a cathode starting sheet. It was shown earlier that even when depositing copper on copper, a substrate-influenced zone appears in the deposit structure, followed by a transition zone and finally by the electrolysis-influenced structure. On copper, the substrate-influenced zone has a thickness of twenty micrometers and on titanium, eventually more than fifty micrometers. Initial nucleation and growth have a considerable influence. In this paper, copper was deposited in a channel cell on four different 304 stainless steel substrates: mechanically polished and anodized, respectively, at 0, +400 and +800 mV/SHE in 1M H2SO4 at 20°C. Copper was deposited under electrowinning conditions after solvent extraction (SX) (40 g/l Cu++, 180 gh/l, H2SO4, 20 or 60°C). The results showed that, although Auger surface analyses of the substrates were only slightly different one from another including the oxide thickness, nucleation and initial stages of growth were very sensitive to the surface treatment of the substrate. Potential step and current step methods gave similar results : progressive nucleation followed by 3D diffusion controlled growth. The highest nucleation frequency was observed on stainless steel anodized at 0 mV/SHE, under various electrolysis conditions. The potential influence of these findings on industrial practice is discussed.

Jan 1, 1999