Search Documents

By K. O. Fagerlund

Theoretically and experimentally determined copper matte settling rate in iron silicate slag has been discussed. Separation and settling rate measurements of sand, homogenised slag and 25%Cu concentrate, 63%Cu industrial, and 71%Cu synthetic copper mattes were carried out by mixing crushed slag and matte samples with silica sand in an alumina crucible and melting at 1300-1350°C. Two different types of slag compositions were employed, with Fe/SiO2-ratio 1.4 and 1.7. The separation rate was followed by taking samples from the .melt. As expected, the settling rate of copper matte in fayalite slag depended on the slag composition, where the increasing silica decreased the matte settling rate. Microanalysis of solidified slags showed that the rate of separation of low grade matte was low compared with high grade matte and the presence of a very small size fraction of matte droplets in slag remained unsettled in stagnant fluid. The production of sulfur dioxide gas inside the molten bath was found to be possible up to a certain iron sulfide content in the matte. Also, copper matte settling rates in industrial furnaces have been discussed.

Jan 1, 1999

By Shize Jin

Effect of four polyols, namely ethylene glycol (EGL), glycerol (GCL), propanediol (PDL), butanediol (BDL) and three organic acids, namely oxalic acid (OA), malonic acid (MA) and succinic acid (SA) on the current efficiency (CE) and the cell voltage during zinc electrowinning was studied. Galvanostatic polarization was conducted in a supporting electrolyte (SE) containing 180 g dm-³ H2SO4, 60 g dm-³ Zn2+ and 8 g dm-³ Mn2+ at 38°C with magnetic stirring. The imposed current density was 50 mA cm-². The anodes were made of a Pb-Ag alloy and the cathodes were made of an aluminum alloy. The results showed that all the polyols tested in this study decreased the current efficiency and the cell voltage, but the decrease of the cell voltage was not important. Oxalic and succinic acids decreased the current efficiency to a less extent than the polyols, but did not decrease the cell voltage much. The only compound that increased the current efficiency was malonic acid, and its capacity of decreasing the cell voltage was the highest within the seven tested organic compounds.

Jan 1, 2003

By Mariola Saternus

The quality of the liquid metal has the biggest influence on the quality of the final products. In the metallurgical industry, and especially in aluminium production the refining process is the important technological stage. Today the most popular are refining reactors with impellers like URO ? 200, which can generate small gas bubbles. A rotary impeller also makes the metal bath to be stirred well. There are two basic hydrodynamic parameters: the flow rate of refining gas and the mixing of refining gas (impeller rotation) that influence metal stirring and generating small gas bubbles. The paper presents the influence of the flow rate of refining gas on the hydrogen removal process from aluminium (final hydrogen concentration), taking into consideration the refining process of AlSi7Mg alloy and using URO - 200. The mathematical model of this process is also presented. The equation needed for calculation of the final hydrogen concentration as a function of the equivalent bubble diameter is shown. Basing on this equation the calculations of bubble diameter and optimal refining time are done. This paper presents the physical model (the water one) of aluminium refining process and the gas dispersion taking into account the fact that the gas flow rate is changing from 2,5 to 17,5 l/min and the impeller speed is changing from 0 to 400 rpm. Schemes of gas dispersion in liquid metal in comparison with the model data are shown and the optimal values of the gas flow rate and the impeller speed are chosen.

Jan 1, 2006

By Wenliang Cao, Jidong Li, Mingjie Zhang, Yiyong Wang

In CaC12-CaF 2 System, we studied the electrode process and discharge mechanism of preparation of Al-Ca alloys by fused salt electrolysis with CaO as raw material. The change of back electromotive force after adding CaO was measured by continuous pulse oscillograph method and the discharge process mechanism was also investigated by cyclic voltammetry. The finial results indicate that back electromotive force decreases by 0.6V after CaO of 1 % is added and there was a peak of oxidation current ahead of the potential at which the negative chlorine ions precipitated. According to thermodynamic calculation, it was determined that current peak was caused by the CO2 produced by 0 2 - ionic discharge due to CaO addition.

Jan 1, 2014

By Chen Zhang

Polycrystalline Ti-rich NiTi thin films have been deposited from a single NiTi target using a DC magnetron sputtering system. Free standing film was obtained by using a single crystal silicon substrate. Thickness ofthe thin films is controlled at around 12 pm. In this investigation, the effect of deposition temperature on the microstructure and transformation temperatures of the thin films is studied. Influence of post heat treatment temperatures on the properties of the thin films is also investigated. Transformation temperatures of the thin films are determined by differential scanning calorimetry (DSC). The surface microstructure of the thin films is studied using a scanning electron microscope (SEM), and the crystallinity is determined using x-ray diffractometry. It is found that the thin film deposited on a hot substrate is crystalline even when the substrate temperature is as low as 300°C, while the normal crystallization temperature for an amorphous thin film is around 500°C. The microstructure of the film deposited on a hot substrate shows a very fine grain size. The grain size increases with increasing substrate temperature during deposition. The effect of post deposition heat treatment on grain size is minimal.

Jan 1, 1999

By M. Z. Mubarok

Effect of single addition of a lignin-based biopolymer additive, DP 2782, at various dosages as well as in combination with thiourea on cathode polarization during copper deposition was investigated by performing potentiodynamic and galvanostatic measurements using a potentiostat. The result of electrochemical measurements was compared with the behaviour of cathode deposition with glue and thiourea additives. Surface micro-appearance of the copper deposit after 1 h galvanostatic scan under current density of 330 A/m2 and various additive type and dosage was evaluated by scanning electron microscopy (SEM) examination. It was found that the addition of 2.5 mg/l biopolymer gave sufficiently polarizing effect of copper deposition. SEM examination of the cathode surface after galvanostatic scan revealed that the combination of the biopolymer with thiourea (2.5 and 3.5 mg/l) resulted in a compact deposit which is comparable with that resulted from the test with glue and thiourea.

By Nan Wang

Based on the commercial computational fluid dynamics software, Fluent, a three dimensional finite-volume model has been established, and the fluid flow and heat transfer in the super-wide slab mold (cross section 3250mm×150mm) of Nanjing Iron and Steel Company has been simulated. The basic feature of flow and temperature field in a super-wide mold has been analyzed, and the effects of mold width, the submergence depth of SEN, outlet angle of SEN, casting speed, superheat and cooling rate on the flow and temperature field have been investigated. The results by comparing several simulated calculations for 3250mm×150mm slab show that a more proper fluid flow and temperature field in the super-wide mold can be obtained with 15°outlet angle, 120~150mm submergence depth of SEN and 1.2~1.4m/min casting speed. The results through numerical simulation provide a theoretical basis for optimizing the configuration design of SEN and choosing reasonable processing parameters for the continuous casting mold of super-wide slab.

Jan 1, 2009

By Tangstadm Merete, Eli Ringdalen

"This paper presents an overview of results from The Norwegian Research Institution SINTEF and the Norwegian University of Science and Technology, NTNU regarding new and ongoing research in silicon production. The main studies are related to condensation of SiO gas and cavity formation. If SiO gas condensation is increased at the top of the furnace resulting in SiO content in the off-gas closer to equilibrium, the Si yield will be increased significantly. Experimental work, simulating a cavity under industrial conditions, has shown that the cavity grows downwards from one layer. Physical appearance of zones in industrial furnaces, and selected reactions in these, are discussed based on results from excavation of industrial furnaces and results from laboratory experiments. Experimental studies of reaction rates for the formation of SiO are presented. Quartz properties are demonstrated to vary between differing quartz types and the effect of this is discussed.Introduction Both the theoretical and industrial issues associated with the production of silicon are described in detail in the textbook written by Schei et al [1]. This book covers the knowledge of silicon production process up to 1998. Together with the work by Myrhaug [1] and by Aasly[2], this is the main basis for this paper. Recent and ongoing research at SINTEF and NTNU focusing on production of Si and SiO in the high temperature zone, dissociation of SiO and condensate and cavity formation will be discussed."

Jan 1, 2012

By T. C. Tseng

Austenitization is a critical stage in heat treatment of steels. The available kinetic data in reference to various initial microstructures are very limited, particularly at high heating rates. In this study, integrated experimental and computational approaches have been conducted to quantify the progress of austenitization and the attained microstructure. In particular, the study is concentrated on cementite and carbide dissolution in two steel grades. Various computational methods are developed to facilitate the study: (l) an algorithm for direct determination of kinetics data as well as progress of transformation from high-rate dilatometer tests; and (2) a suite of mesoscale computational models for particle dissolution, elements diffusion, mechanics, thermodynamic and the resulting kinetics of transfonnation. Critical exprimentation is carried out using advanced techniques in microstructure characterization, chemical analysis, and Gleeble thermal-mechanical simulator on specimens of well-controlled initial microstructures. Keynotes: Cementite, Carbite, Dissolution, Steels, Austenitization

Jan 1, 2003

By Osarnu Inoue

In Mitsubishi Continuous Copper Smelting and Converting Process, smelting, slag-matte separation and matte converting are continuously carried out in series in three furnaces connected by launders. As a result of this operational configuration of the furnaces, influence of the change in operating condition in upper stream, such as variation of feeds in the smelting furnace, propagates to down stream with some delay. In order to achieve stabler operation, process control algorithm based on the dynamic characteristics of each furnace would be very effective. In this study, the dynamic process simulation model was developed for the smelting furnace. The model consists of two mathematical modules, i.e. the thermodynamic module and the mixing module. The calculation results using operating data obtained at Naoshima Smelter showed good agreement with the actually observed change in temperature, composition and flow rate of matte and slag at the outlet of the furnace. In addition, operation parameters such as reaction efficiency of oxygen and coal, dead volume of melts were estimated.

Jan 1, 1999

By R. Ghisleni, R. E. G. Bohrer, L. Radtke, R. M. C. Santana

"The major source of environmental pollution in urban areas is the transport sector and its impact on human health and the greenhouse is preoccupying. In many works of literature is monitored the pollutants in urban cities, however in specific areas such as universities, they are scarce. Therefore, the aim of this work is to monitorate the gaseous pollutans in a bus terminal at Santa Cruz do Sul University-UNISC and to develop a control framework of the air quality. Six points were selected for monitoring, being one of them inside a bus. The monitoring of CO, HC and CO2 were carried out on arrival and departure of the bus. Preliminary results conducted in a day of spring showed that the most critical condition was during the night shift, where the concentration of CO (200 ppm) was the highest, caused by the vehicles increase, due to the larger number of students.IntroductionThe first major global assessment of climate change science in six years has concluded that changes in the atmosphere, the oceans and glaciers and ice caps show unequivocally that the world is warming. The report released on February 2, 2007, the first of four volumes to be released this year by the IPCC, also confirms that the marked increase in atmospheric concentrations of greenhouse gases is the result of human activities.The transport sector has become by far major source of environmental pollution in urban areas. The continual traffic growth has raised concerns over the impact of traffic emissions on human health and urban environmental quality, and has fuelled the demand for a coherent regulatory framework for the management of traffic, air quality and emission at urban level, as well as at regional and national scales.In Greater Metropolitan São Paulo, Brazil, fossil fuel combustion in the transportation system is a major cause of outdoor air pollution (Miraglia&El Kouri, 2007). In China several studies on gaseous emissions are being conducted by F. Costabile&Alegrini, (2007), developed a study on the pollutants in the city of Beijing suggesting methods for the control of pollution.The results obtained from the estimation of the atmospheric pollutants emitted monthly in Campo Grande/MS, Brazil, by buses and minibuses, which employ diesel, biodiesel or natural gas as fuels showed that the substitution of diesel by biodiesel would diminish the emissions of pollutants (Kozerski&Hess, 2006)."

Jan 1, 2008

By R. D. Pehlke

The history and present status of continuous casting of steel are reviewed, including a genera 1 description of current processes. Plant layout, process development and elements of machine component design are outlined, and key steps in integration into a stee-1 production system are detailed. Recent productivity advances and improvements in quality are described. Process developments are reviewed, and some future avenues for this technology are considered.

Jan 1, 1985

By Toshiyuki Kozuka

CdTe semi-conducting materials have been expected as solar cell materials because its theoretical energy conversion ratio is very high. The actual efficiency still low, however, many research works have been done in order to improve the efficiency. And crystal orientation is one of possibilities for that. In this work, a new method using intense magnetic field for a control of texture of CdTe crystals will be proposed, where the CdTe film was electro-deposited under an intense magnetic field. CdTe is less affected by magnetic field, because of its cubic structure, but Cd or Te has hexagonal structure, which is sensitive for magnetic field. In this paper, crystal orientation of Cd or Te film, which can be utilized as basic layer for CdTe deposition, will be developed.

Jan 1, 2006

By W. Persson

The first installation at a copper smelter of a Semtech OPC System for continuous, on-line production control of copper converting in PS converters took place in 1994. At present OPC systems are installed at 19 PS converters. The technology presents to the operator real-time information on the progress of the process he is controlling in the form of optical process parameters, thus facilitating dynamic process control. The optical process parameters are based on time- and wavelength resolved registrations of the light emitted by the off-gas flames and identification of correlation between these parameters and characteristic metallurgical process data. The present paper provides a description of the technology as seen by the furnace operators and a summary of operating experiences made during five years of full-scale, operation at various smelters, reviews influences from the technology on smelter operational practises and comments on recent developments as regards new applications of the technology.

Jan 1, 1999

By G. White

Traditional atmospheres used for Aluminum annealing have been air, exothermic gas, and cryogenic purity Nitrogen. Air and exothermic gas have several problems associated with them such as surface discoloration, toxic emissions, and explosion hazards. High Oxygen levels can cause Magnesium streaking and oil staining, and therefore pure Nitrogen has been the atmosphere of choice for high quality Aluminum coils. A comparative study was made on key Aluminum alloys annealed in Nitrogen with different Oxygen concentrations to determine the effect on surface quality. The atmosphere composition inside the furnace was analyzed during the purge and heat cycle to determine its effects on purge times and exhaust emissions. The Aluminum coils after annealing were visually inspected for surface staining before and after rolling. The lab study revealed that Nitrogen with up to 1.0% Oxygen is acceptable, and did not adversely effects the surface quality or any of the other processing variables. However it isbelieved that higher Oxygen concentrations are acceptable depending on the rolling oils and alloy systems.

Jan 1, 1996

The resist profile simulation is carried out using the combined data obtained. The nematic liquid crystal is clear only when a long range order exists, in the whole medium. using the Jones matrix method. Director can change from point to point and is, in general, a function of space. Details of the lens structure and of the devices fabrication and performance are described. Light from conventional light source or laser is passed through a polarizer and then incident on the specimen At the nematicisotropic, transition temperature, the medium becomes isotropic and looks clear and transparent. The transition can be approached by changing the impurity concentration or, indirectly, by tuning the temperature since the pinning strengths of the random and crystal potential have in general a different temperature dependence.

Jan 1, 2006

By Finn Olesen, Melina Garcia, Mark William Kennedy

"Furnace resistance is a function of the complex interrelationship between many factors including: operating practice, slag conductivity, temperature, power intensity, and geometry (electrode shape, diameter, spacing, immersion, slag depth, etc.).Accurate prediction of resistance is critical for success of the overall furnace design. The sizing of electrodes, columns, bus-bars, and transformers are all impacted. Estimation of minimum and maximum resistance or maximum operational current, as well as the maximum operating voltage are of fundamental importance.Various mathematical tools have been developed to assist designers with the selection of furnace dimensions and the prediction of resistance. Elkem found the methods of Downing and Urban 1965 and Westly 1975, to be particularly useful.In the current paper, comparisons are drawn between data from spent aluminum pot lining (SPL) demonstration testing at Elkem Bjolvefossen and predictions based on these classical tools and 3D finite element modeling (FEM) with COMSOL.®"

Jan 1, 2012

By Laurentiu Nastac

"The importance of investigating solute redistribution during the unidirectional solidification of multi-component alloys is broadly discussed in the literature. A previously developed analytical model that was experimentally validated for Al-Cu, Sn- Bi and Fe-Si dilute binary alloy systems is used in this article to study in detail the solute redistribution, the liquid/solid interface stability based on an extended transient constitutional undercooling criterion and the size of the initial transient region during the unidirectional solidification of Ti-6-4 and Ti-17 alloys. A comparison between Ti-6-4 and Ti-17 alloy systems with respect to interface stability and the size of the initial transient region is also provided. The effective partition coefficients of the alloying elements in these alloys were determined based on specially designed experimental measurements.IntroductionThe importance of investigating solute redistribution during alloy solidification is broadly discussed in the literature [1-5]. One of the relevant applications of this study would be the mathematical modeling of equiaxed and columnar solidification of multicomponent alloys. This includes the instability of the solid/liquid interface. There are several mass and heat transfer processes that involve the calculation of solute redistribution during directional solidification such as industrial directional solidification processes, continuous casting, remelting processes, Czochralski crystal growth technique, floating zone techniques, etc."

Jan 1, 2012

By Debbie Marshall

Process water is an important consideration in the development of a nickel laterite project. Depending on the location of the ore body, sufficient fresh water may not be available and it may be necessary to use seawater (or saline groundwater) for ore preparation. This introduces various species, which have major effects on materials of construction and leaching chemistry. This paper summarizes batch testwork completed at the Falconbridge Technology Center. The leaching behaviour of eleven different laterite ore samples were compared using seawater and fresh water. For brevity, six of the eleven samples are reported here-the other five samples showed similar results. Each ore type was leached under identical conditions in both freshwater and seawater and the leaching chemistry compared. The batch test results were confirmed in a continuous pilot plant, and leach kinetics for the two systems were compared. Keywords: high pressure acid leaching, laterites

Jan 1, 2004

By Linping Yu

A simplified ED process was developed for organic acids recovery from cyclohexanone waste in this paper. In this regard, the one-stage ED was investigated directly without pretreatment, such as ion-exchange or nanofiltration to removal of foulants. The current efficiency and the energy consumption in the ED process for the recovery of carboxylic acids from cyclohexanone waste is theoretically analyzed and experimentally tested. The concentration of recovered carboxylic acid is related to many parameters and still needs more work to be determined.

Jan 1, 2009