Search Documents

By Miaoyong Zhu, Sen Luo

"A two-dimensional CAFD model was developed for simulating the solute diffusion-controlled dentritic growth in the low Peclet number regime. Mass conservation and local equilibrium at the solid/liquid interface were solved to determine the growth velocity of interface with consideration of constitutional and curvature undercooling. The modified decentered square growth proposed by Wang et al was adopted to capture the first eight neighboring cells. The comparison between the classic Lipton-Glicksman-Kurz (LGK) analytical model for steady state tip variables and the simulated values showed that the present model was capable of quantitatively determining the dendritic growth, and the simulation tests demonstrated that the effects of the mesh anisotropy in growth kinetics and crystallographic orientation were eliminated. The numerical simulations were performed to the dendritic growth ofFe-0.6%C binary alloy in undercooled melt, and the results showed that the present model could predict the dendrite morphology with artificial growth orientation in acceptable level.IntroductionDuring the solidification of metals and alloys, the dendrite grows from the substance or the undercooling melt and solute redistributes between the dendrite and the interdendritic liquid. The solidification microstructure is close related to the phase and solute evenness and has a close linkage with the properties of final production.In the past few decades, various kinds of deterministic and stochastic models have been developed to predict the evolution of microstructures in solidification, with the fast development of computer power. Among these methods, Phase Field (PF) model [1, 2] has been known as one of the most adequate deterministic models for directly simulating the dendritic growth. However, there is a vital drawback that the PF method requires considerable computation time and is limited to simulate very small domains with a few dendrites [3]. On the other hand, stochastic models, such as Monte Carlo (MC) method [4, 5] and Cellular Automaton (CA) method [6-8], have been usually applied to predict the solidification microstructure evolution. Comparing with the MC method, the dendritic growth kinetics is explicitly integrated in the CA model, while the MC model doesn't. Therefore, the CA method is more reasonable to predict the dendritic growth during the solidification of melt."

Jan 1, 2013

By C. H. Quan

Solvent extraction tests were carried out on a rare earth chloride solution derived from monazite processing to determine the effect of extractant and diluent on the distribution coefficients between organic and aqueous phases, and the separation factor between rare earths. The extractants were 20% by volume di-2-ethyl-hexyl phosphoric acid (DZEHPA) or 2-ethyl-hexyl phosphonic acid (Ionquest® 801). Four Shellsol diluents were tested ranging from nil to 100% aromatic content. D2EHPA gave the highest rare earth extraction for a given pH but was less selective than Ionquest. The geometric mean separation factor between adjacent rare earths varied from 2.41-2.56 for D2EHPA to 2.62-3.01 for Ionquest. The nil-aromatic diluents (Shellsol 2037 and 2358) gave better separation factors in Ionquest but, in D2EHPA, were slightly inferior to the 100% aromatic diluent Shellsol AB. Yttrium behaved as a pseudo-heavy rare earth with a distribution coefficient lying between Ho and Er, as expected from its ionic radius.

Jan 1, 1992

By Guozhu Ye

Hydrometallurgical zinc recovery from EAF dust has several advantages compared to pyrometallurgical alternatives in terms of low temperature operation, lower energy consumption and higher flexibility. Many hydrometallurgical processes have been suggested and tested over the years without success. The main reasons are: -Low leaching yield of zinc due to the fact that a high fraction of ZnO in the EAF dust exists in the zinc ferrite structure which makes selective leaching of ZnO not possible -Many of the proposals could not handle the halide in the EAF dust To eliminate these two disadvantages, two zinc ferrite elimination concepts have been tested and developed in the REZIN project of the EU 5th Framework Programme. The two concepts for zinc ferrite elimination could be shortly described by the following chemical reactions: A. ZnOFe2O3 + 2CaO = Ca2Fe2O5 + ZnOfree B. ZnOFe2O3 + C = Femet + CO/CO2 + ZnOfree These two concepts were investigated in details in combination with a subsequent leaching step using the novel EZINC process for recovery of zinc from EAF dust. Leaching of pretreated samples has shown great increases of a zinc recovery yield. A zinc recovery of over 90 % could be reached, as compared to about 50 % for no-pretreated samples. This paper will describe the two concepts in details.

Jan 1, 2006

By D. J. Sellmyer

This paper is Intended to review recent developments in the application of rare earth-transition metal alloys as high density, rewritable data-storage media. First generation magneto-optic media are based on amorphous Tb-FeCo or GdTb-Fe alloys which are adequate but could use improvements In certain respects. A very difficult materials-design problem is encountered because of the following requirements: a sufficiently large Intrinsic uniaxial anisotropy, a Curie temperature in the range 100-300°C, a sufficiently high coercivity, a sufficiently high optical absorption, a high Kerr rotation, reflectivity and high carrier-to-noise ratio, a high storage density, a very fine and homogeneous nanostructure, long-term stability, and inexpensive production. , Fundamental issues such as the relationships between the nanostructure and perpendicular magnetic anisotropy, and electronic structure and Kerr rotation are discussed. Attempts to tailor the properties by rare-earth alloying and by preparing compositionally-modulated, nanostructured multilayers are outlined. Challenges and opportunities in competitive materials such as garnets, ferrites and Co/Pt multilayers are briefly discussed.

Jan 1, 1992

By Srinath Viswanathan, Zhijing Zhang, Ramana G. Reddy

"The viscosity measurements were carried out on melts of 380 aluminum alloy containing 20 volume % SiC particulates under various shear rates at different temperatures using a Brookfield viscometer. Results showed that viscosities of the melts increased with decreasing temperature and decreased with increasing shear rate. These results were compared with those of 356 alloy and it was found that the temperature had a more significant effect on viscosity of 356 alloy than that of 380 alloy containing SiC particulates. Based on the present experimental data an empirical viscosity model, which considers the effects of both solid fractions in the melt and shear rate, is proposed.IntroductionDiscontinuously reinforced metal matrix composites materials (MMCs) such as aluminum alloy containing SiC particulates have considerable potential for applications in the automotive industry because of their superior stiffness, higher specific mechanical properties, better dimensional stability and strength retention at elevated temperatures when compared to their monolithic counterparts. They have a great advantage in the specificity of their properties, meaning that specific materials can be engineered for specific applications. With such freedom of design, materials engineers have to accumulate a very large database of mechanical properties. Among these properties, the viscosity of alloy slurries is very important for producing, casting and forming process of metal matrix composites materials because viscosity has a decisive influence on fluid flow. The understanding of the rheological behavior of alloy slurries is necessary for these materials to become economic reality. Therefore, a study was carried out to measure the viscosities of 380 aluminum alloy containing 20 volume % SiC particulates under various shear rates and temperatures. In addition, a viscosity model representing the primary features of the alloy slurries was developed."

Jan 1, 1999

By Dachun Liu, Yifu Li, Baoqiang Xu, Yongnian Dai, Bin Yang

"The removal of impurity arsenic from crude tin is one of the major problems in the process of tin refining. Through a thermodynamic analysis on vacuum refining process of crude tin, the vapor pressure of impurity arsenic under different temperatures can be obtained, which demonstrates that it is possible to separate tin and arsenic by the vacuum refining process. This paper attempts to verify the behaviors of impurity arsenic. The experiment result shows that through vacuum distillation, crude tin with 0.16% arsenic can be refined from crude tin with 0.96% arsenic, and about 50% impurity arsenic can be collected in the form of metallic arsenic.PrefaceThe crude tin obtained by the reduction process is insufficiently pure for most applications, even smelting from tin concentrate. Arsenic is a common impurity in crude tin and also one of the predominant elements to affect tin performance. Arsenic is a poisonous metal that has long been linked to an increased risk of cancers, diabetes, thickening of the skin, diseases of the liver and digestive complications, so there is a mandatory limit on the amount of arsenic (<0.015%) in tinfoil wrapper and tin layers for food packaging. Arsenic causes a poor appearance and plasticity, and increases viscosity. The impurities content of crude tin fluctuate over a wide range; a lot depends on composition of tin ore concentrate, treatment method and technological process before reduction smelting. And the content range of arsenic is usually 0.5~4%, but it is higher in some factories."

Jan 1, 2012

By María Cristina Ruiz

Hematite precipitation is a convenient alternative for the removal of iron from leaching circuits because of its chemical stability, high density and high iron content. The precipitation of hematite from ferrous sulfate solutions was studied in a batch reactor. The precipitation occurs by two sequential steps: oxidation of the ferrous to ferric ions followed by hydrolysis of the ferric to hematite. The main objective of this study was to determine the effect of the main operating variables on the rate of two steps of hematite precipitation. The variables studied included: stirring speed (100 to 600 rpm), temperature (160 to 200 ºC), concentration of sulfuric acid (1 to 10 g/L), initial iron concentration (1 to 15 g/L), and partial pressure of oxygen (1 to 6 atm). The sulfur content and the particle size of the solids that precipitated under various conditions were also determined. The results showed that at low temperature and high acid concentration the rate of Fe3+ hydrolysis is the step that controls the overall process. The variable that affects most the rate of Fe2+ to Fe3+ oxidation and the rate of hematite precipitation is the temperature.

Jan 1, 2008

By Tam Tran

Most new gold mines in Australia are required to treat tailings to reduce cyanide levels before they are discharged to storage ponds to meet the stringent environmental management guidelines set by government statutory authorities. In New South Wales, the average level of weak acid dissociable cyanide allowed in open tailings dams is now limited to 20 ppm, As stringent environmental guidelines continue to be enforced in Australia as well as in other parts of the world, the management of cyanide wastes has emerged as a key issue for the gold mining industry. This paper provides a critical evaluation on technical aspects related to the use of ion exchange resins and affiliated processes in cyanide management and tailing treatment. Particular attention is given to the use of ion exchange resin technologies in the processing of mixed gold-copper ores, where cyanide usage is the highest. Information presented in this paper is heavily drawn from the experience on the application of ion exchange resin processes at May Day mine, in New South Wales, Australia and associated pilot plant test programs. Issues related to the management of thiocyanate, especially with respect to the recovery of cyanide from thiocyanate are also discussed.

Jan 1, 1998

By David K. Melgaard

Electroslag Remelting (ESR) is a complex process used to produce high quality specialty alloy materials. The quality can be directly correlated to variances in melt rate and immersion depth. Conventional ESR furnaces control these quantities using two independent control loops using proportional changes in current for melt rate and driving the electrode up and down to match a voltage set point for immersion depth. However it is well known that the control loops are highly coupled, i.e. changing the current to account for melt rate deviations changes the voltage depth relationship and vice verse. In addition the noise in measurements of the ESR process can be considerable, forcing conventional controllers to use highly damped responses. A new model-based controller has been developed to embody the coupling and improve responsiveness by using estimates from a reduced-order linear ESR model and the typical process measurements to control melt rate and immersion depth simultaneously. Kalman filtering is used to optimally combine the model estimates of eight process states and the measurements of voltage, current, position and mass to estimate the instantaneous melt rate and immersion depth. Several ESR melts under steady state and transient conditions were conducted to evaluate the performance of the new controller. This paper will discuss the design of the new ESR model and controller and will present experimental results demonstrating its much improved control and responsiveness. While this controller was developed for the ESR process, the effectiveness of model-based control in managing such a complex process with relatively simple equations suggests the approach could be employed for many other processes as well.

Jan 1, 2006

By X. Jay Gao

A fast high-temperature carburizing process integrated with materials design and optimization via a systems design approach was developed to significantly reduce process cycle time. Process experiments were focused on boost cycles to obtain a robust boost process and investigate surface reaction kinetics, primary carbide formation and dissolution. Weight gain and microhardness were measured, all showing evidence of non-monotonic time evolution for longer boost times at higher temperatures. Optical and electron microscopy and other techniques have been used to identify possible carbides, their location and types. These results assist the picking of first boost time with least variation rate in terms of content of case carbon and carbides, dissolvable in subsequent diffuse if any. The results also provide critical information to properly formulate surface reaction kinetics and diffusion and formation kinetics of carbides modeled using DICTRA. Keywords: high temperature vacuum carburizing, partial pressure carburizing, heat treatment, process development, carbide, case hardening, microstructural analysis, over carburizing

Jan 1, 2003

By E. R. Vance, D. R. M. Brew

"Historically, Ordinary Portland cement has been the preferred medium to immobilise arsenic. However, arsenic in cement gives rise to calcium-arsenic phases and their known decomposition to calcium carbonate and arsenic trioxide via atmospheric carbonation raises serious questions about the long-term suitability of cement for arsenic immobilisation. Alternative matrices such as low-temperature ceramics (LTCs) potentially offer superior resistance towards carbonation owing to the absence of calcium. Consequently, the potential for arsenic immobilisation using LTCs has been investigated. Both AsIII and AsV have been incorporated and samples assessed according to a standard leaching protocol. AsIII persists in the porewater of alkali-bonded LTCs as sodium arsenite rendering them unsuitable for immobilisation. Thermal treatment of these LTCs to consolidate the microstructure and reduce open porosity resulted in sodium-rich cryptocrystalline matrices that leached arsenic and sodium readily. The omission of sodium in acid-bonded LTC formulations resulted in leach data that were close to the target value of 5 µg/ml in Toxicity Characterisation Leaching Protocol tests.IntroductionArsenic is a carcinogenic substance and its adverse effects of on humans, flora and fauna have been well documented [1-5]. As a consequence, many papers have been written on the prospective handling of arsenic-bearing waste. These can largely be divided into: (a) cleanup of arsenic-contaminated water using bacteria, precipitation, and/or UV irradiation to generate arsenic-rich sludges for subsequent immobilisation; (b) cleanup of arsenic-contaminated soil via chemical extraction for immobilisation of the As concentrate; and (c) immobilisation of industrial waste contaminated with As."

Jan 1, 2008

By Takamitsu Nakasuga, Haiping Sun, Kyushu University, Katsumi Mori

"The kinetic behavior of reduction of chromite ore by liquid iron containing carbon and silicon has been investigated under various experimental conditions to clarify the reduction mechanism. It was found that the reduction rate of chromium ore by liquid Fe-C alloy was very slow. In addition, when carbon and silicon coexisted in the iron melt, silicon was found to preferentially oxidized to form silica, which favored for the fonnation of liquid slag and the rate of reduction was considerably accelerated. The similar effect was obtained by the addition of some fluxes, such as SiO2, Na2B407, CaO-SiO2, which also promoted the formation of a liquid slag and thus the reduction rate in the early stage also increased.IntroductionThe reduction of Cr2O3 is a basic reaction for production of ferro-chromium from chromite ore and for chromium recovery from the slag fonned during the decarburization period of a stainless steel-making process. The reduction of chromite ore consumes much energy and its reaction rate is not so high. Thus, in order to increase the reduction efficiency, it is strongly desired to clarify its reduction mechanism from the practical and the theoretical points of view."

Jan 1, 2000

By Javier Antoñanzas, Juan Carlos Múgica, Lourdes Yurramendi

The gasification of wastes containing an organic fraction is usually performed at low-medium temperature using different kind of catalysts. The off gas obtained is a mixture of carbon oxides, mainly carbon monoxide, and hydrogen and can be used for different energetic applications. The main problem is the production of tars in the off gas that has to be separated from the valuable gas flow and, finally, treated separately. An interesting alternative is the partial or total treatment of organics at high temperature. In this case, the off gas contains a higher content of hydrogen and elemental carbon as particulate matter. The energetic source to obtain a temperature in the range of 1,000 - 1,200 ºC is obtained by a plasma torch. In order to make de process attractive, an important issue to be considered is to commercialize the carbon obtained for different industrial applications.

Jan 1, 2008

By F. Mucciardi

While flash smelting and converting are capturing a greater share of the market, injection through circular injectors will remain with us for the foreseeable future. The use of top lances for injection is a key feature in several processes (e.g. Mitsubishi, Ausmelt). Tuyeres, on the other hand, are incorporated into a number of processes (e.g. Noranda, Peirce-Smith). To date no lances or tuyeres are cooled by an external source. The reagent provides the bulk of the cooling. With limited cooling, it is normal to have substantial wear on the nozzles - especially in the case of lances. To overcome the issue of wear, a new patented injector (lance or tuyere) has been developed by Noranda and McGill University. This novel unit is based on heat pipe technology. It can operate for an extended period of time without wearing. Enhanced lance/tuyere life is achieved by operating the injector at a low enough temperature that promotes the formation of a thin frozen layer on the outer body of the unit. The vaporizing and condensing substance within the unit acts to cool&apos; the high heat flux portions and dissipate the heat to areas of low heat flux outside the vessel. A fairly large number of tests have been conducted with a prototype unit. The tests have shown that the heat pipe lance is a viable unit. In this paper is detailed a test which illustrates how the lance functions when pure oxygen is injected into copper matte. In addition, the findings from a basic study of a heat pipe in high heat flux environments are also presented.

Jan 1, 1999

By Nozomu Uchida, Uematsu Keizo, Daisuke Shouji

"Grain orientated microstructure was developed for the improvement of ceramic characteristics. Novel polarized light microscopy was developed to examine the grain orientation quantitatively. The degree of grain orientation was estimated from the retardation determined with a Berek compensator. The method was essential to determine a minor grain orientation, which could not be analyzed by means of conventional X-ray measurements. The data were favorably related to ceramics characteristics. The comparis of the ceramics with various degree of orientation was very important to explain the change of ceramic characteristics with processing.IntroductionMicrostructure with grain orientation has a high potential for greatly improving characteristics of ceramic. However, there has been strong restriction on processing and material for developing this structure. It has been crucial to apply forming methods involving high shear such as injection molding1). Grains must have an elongated shape.In recent years, much attention has been paid on the effect of high magnetic field on diamagnetic materials2)3)4), Many ceramic materials are known to be diamagnetic. High magnetic field has a high potential to orient grains. The principal driving force for grain orientation is the magnetic anisotropy of material, which is generated by non-cubic crystal symmetr5). This method of grain orientation is not restricted by grain shape, and can be applied to all materials having non-cubic crystal structure.This study uses alumina as raw materials, and produces alumina ceramics with orientated grain in high magnetic field (10T). Alumina has a magnetic anisotropy due to hexagonal crystal structure. The degree of grain orientation in the green and sintered bodies will be examined and their relevance to magnetic field will be discussed."

Jan 1, 2000

By Yoshimasa Oda

The tank house of Tamano Smelter has adopted a high current density electrolysis operation applying PRC (Periodic Reverse Current) method and before 1991, it had materialized both high production capacity of 161,000 tons/year and high labor productivity. However, recent rapid rise of Japanese currency in foreign exchange market has urged us to further exert our efforts in reduction of labor cost. In order to achieve this goal of labor cost reduction, we have completed, in 1994, our phase four production expansion project which incorporated significant re-structuring of the organization and we have accomplished annual production of 191,000 tons/year. This project can be outlined as increase of number of cells for electrode exchange per day in the commercial electrolysis process to meet the increased number of cells and increase of the capacity of impurity treatment process. These improvements were done with minimum installation of new equipment and facilities and with achievements in efficiency and manpower saving of the existing facilities. Together with these improvements, rationalization in the starting sheet section was carried out by changing the material of mother blanks as well as changing their maintenance procedures. At the same time, the crane in this section was modified to enable automatic operation by a fuzzy control. As a result, we were able to save manpower equivalent to 5 operators in this section. With these improvements, the production capacity was increased by 18% and labor productivity by 25%.

Jan 1, 1996

By J. P. Ibáñez

The uptake of copper from extremely dilute aqueous solutions by alginate in the form of protonated dry alginate beads was investigated. Barium was used to cross link the alginate forming the beads. The effect of various experimental parameters such as pH and metal ions concentration on the uptake of copper were studied. The uptake was strongly dependent on the Cu-bearing solution pH up to a value of 4.5. A removal of 100% o was achieved when the initial concentration of copper was as low as 8.0 mg/L. The maximum uptake, i, e., the loading capacity, was found to be 167 mg of copper per g of beads. The mechanism governing the removal of copper was found to be ion exchange between protons of the alginate beads and cupric ions of the solution. For this ion exchange process a molar ratio, d[H+]/d[Cu2+], of 2.0 was determined. EPMA-EDX analysis of the Cu-loaded beads showed a uniform distribution of the ions throughout the structure of the alginate, regardless the solution pH. This may suggest that this sorbent material is a porous ion exchanger having high permeability and capacity. The uptake of copper and of the heavy metals cadmium and zinc by this sorbent is compared.

Jan 1, 1999

By Jun Iwai, Osamu Takai, Yasushi Inoue, Hiroyuki Sugimura

"Infrared reflection absorption measurement was performed during plasma-enhanced chemical vapor deposition of silicon dioxide films at room temperature. Hydrocarbon contaminants adsorbed onto growing film surface are oxidized by oxygen radicals in plasma resulting functional groups which include C=O and C-O bondings. These groups exist only near the surface and are hydrolyzed rapidly after exposure to air.IntroductionRecently low-temperature silicon dioxide (SiO2) deposition has been in a growing industrial demand in pa1ticular, polymelic substrates such as polycarbonate and polyethylene telephthalate, which have poor heat resistance, need low process temperature (near room temperature) in coating of SiO2 which is a suitable material to improve optical and mechanical properties of polymenc products. Plasma enhanced chemical vapor deposition (PECVD) using organosilicon reactants is one of the most promising technique for lowering process temperature, so that it has been extensively studied1-12. In the present; however, hydrocarbon contaminants and a plenty of Si-OH termination in Si-O-Si networks tend to exist in the films, which degrade mechanical, optical and electrical properties of the films. It is necessary to understand the deposition mechanism at, low temperature in order to solve the problems. We have studied the low-temperature PECVD of Si02 by spectroscopic diagnosing techniques such as optical emission and mass analysis6-7, 11- 12Infrared reflection absorption spectroscopy (IR-RAS) has been a well-established technique for characterization of thin films on metals as· well as on semiconductors and insulators13-17. In this paper, we report on' the surface reaction of room-temperature PECVD of Si02by using in situ IR-RAS."

Jan 1, 2000

By M. Potesser

After the primary or secondary lead production the bullion lead is remelted and charged into a vessel with following refining process. The removing of arsenic, antimony and tin takes place by salt slags or oxidizing gases like air or pure oxygen. Due to the increasing lead price, Messer Austria GmbH in cooperation with the institute of Nonferrous Metallurgy at the University of Leoben have developed a new process named OXIPOT for the refining of tin, arsenic and antimony. The OXIPOT process is in principle based on purging technology with a ceramic or steel purging device. This leads to an increased retention time of the refining products due to the deeper bath level and an optimized specific reaction volume concerning the bubble size. This paper describes the process, pilot plant, and thermodynamic calculations for the optimization concerning the selectivity of element removal.

Jan 1, 2008

By Cevat Serdar Kucukkaragoz

The kinetics of prereduction of Chromite by carbon was studied under argon atmosphere at temperatures between 1000°C and 1300°C . The compacted and agglomerated specimens were reacted by using a TGA system. The mixing characteristics and the degree of compaction of the chromite and coke particles were the main parameters influencing the reduction kinetics. The reduction rate increased with temperature reaching to 81% reduction at 1300°C. The metallization started as the metallic nucleation around the particles which was first observed at 1100°C. The particles were surrounded by the metallic phase at approximately 40 % reduction obtained at 1200°C. At 1300°C, the reduction proceeded with a high rate during initial stages and with a low rate at final stages. The reduction was found to proceed in the sequence of Fe3+to Fe2+, Fe2+ to Fe(metal) and Cr3+to Cr(metal) with the formation of carbides.

Jan 1, 2006