Search Documents

By Jose Carlos D’Abreu, Edelink Efrain Tinoco Falero, Mauricio Marcos Otaviano, Helio Marques Kohler

Nowadays the most important Direct Reduction - DR processes in shaft furnaces has to deal with carbon fines precipitation and DRI carburization issues. Based in a cooperative research program joining Catholic University (PUC-Rio) and SAMARCO Mining Co, a project dealing with pellets reduction and those two phenomena was established. This work analyzes kinetically the three reactions mentioned before, considering typical values for the operational variables temperature, flowrate, pressure and gas composition, parameters commonly used to control the DRI formation in the Reduction Zone - RZ of the shaft furnaces. From laboratories experimental results, the kinetic equations for those reactions were established and, using the superposition principle, generated a specific global kinetic model for the iron oxide reduction and the soot formation. Finally, using those experimental results and applying a planned statistical factorial analysis for the experiments, the numerical coefficients for each equation were calculated and the correlation factor determined for the proposed global kinetic equation.

Jan 1, 2015

By Victor Stancovski, Uday Pal, Stephen C. Britten

"An in situ electrochemical technique for measuring the concentrations of easily dissociable oxides in slags at temperatures between 1200-1600°C is being developed. The technique utilizes a partially-stabilized-zirconia solid electrolyte (PSZ), which conducts oxygen ions, to separate a reference-gas compartment from the slag of interest. Three types of measurements are currently under investigation which yield different information concerning the slag phase and hence will be combined into a single amperometric device for monitoring the properties of easily dissociable slags.Type I utilizes an open-circuit-voltage measurement between the reference gas and the slag phase. Type II utilizes a potentiostat to apply a direct current potential step or sweep between the inner and outer compartments of the electrolyte, driving oxygen ions from the slag into a reference gas. With the use of open-circuit-reference electrodes, the resulting current-potential profile reveals the dissociation potential and concentration profile of dissociable oxides such as those of iron, manganese, and chromium. Information on the transport properties of the cations can also be generated from these measurements. Type III utilizes a potentiostat with reference electrodes to carefully electrolyze a known volume of slag by removing large quantities of oxygen ions from the slag to the reference gas. The coulombs of charge removed at different applied potentials can be used as a direct indication of the concentration of each dissociable oxide species present within the slag."

Jan 1, 1997

By Olga Slavkina

A new technology of bacterial leaching by means of the Thiobacillus ferrooxidance bacteria is proposed. The equations of reactions that describe of the first and the second stage of bacterial leaching of sulfide raw materials containing non-ferrous metals are given. The theory is analyzed and the technology of processing of some complicated substandard concentrate containing copper and zinc is proposed. The main technological operations including a two-stage bacterial leaching and stages of copper and zinc recovery in the form of marketable product are described. The results of the experimental validation of the main technological parameters of the first stage are given. The main possibilities of a more complete zinc and copper recovery at the second stage of bacterial leaching are discussed in comparison with single-stage leaching process.

Jan 1, 2003

By Olli Järvinen

The capacity of the Outokumpu Pori refinery is today about 125 000 mt in 1998. The anode slime amount is about 700-800 mt. The copper is removed with pressure leaching. Selenium roasting is done with the gas roasting. The doré smelting in the furnace is done with the tilting rotating converter with oxy-fuel burner (TROP). Doré anodes are treated in the silver electrolysis. Gold is recovered from the gold mud with the quick hydrochloric acid leaching process. The important point in the leaching is to get into contact the solid copper with the oxygen and liquid. Outokumpu has an efficient agitator for this purpose. The GLS-agitator (GLS=gas, liquid and solid) is powerful for mixing oxygen, liquid and solid together. The current production in Pori plant is 40000 kg of silver, 5000 kg gold, 40000 kg of selenium and one hundred kilograms of platinum-palladium concentrate.

Jan 1, 2000

By C. A. Landolt

Inco pioneered the use of tonnage oxygen in non ferrous metallurgy when it commissioned the first .industrial oxygen flash smelting process for the treatment of copper concentrates in the early fifties. This technological innovation was followed by other applications of technical oxygen. Inco is currently implementing a Sulfur Dioxide Abatement Program designed to reduce S02 emissions from the smelter by 60% in 1994. The new flowsheet includes new equipment for the oxygen flash smelting of Cu-Ni concentrates and for flash conversion of chalcocite. Oxygen smelting and converting technology will lead to a substantial decrease in use of fossil fuels and to generation of high strength S02 off gases suitable for efficient fixation in a new acid plant.

Jan 1, 1992

By M. D. Light

An intelligent control system (ICS) is being developed for ferrous iron oxidation by Thiobacillus ferroxitdans. The ICS provides computerized data acquisition and' control of process variables (temperature, Eh, pH, dissolved oxygen arid carbon dioxide concentrations and dilution rate) to maintain the ferrous iron oxidation at the highest possible rate. The ICS uses fuzzy logic for analysis of data inputs and implementation of control strategies. T:his paper provides preliminary information on the development of the ICS and? its operation.

Jan 1, 1991

By William K. Tolley

The U.S. Bureau of Mines (USBM) is investigating hydrometallurgical processing techniques to recycle metals from semiconductors and other advanced materials. Cadmium and tellurium were recovered from mixed CdTe/CdS scrap produced in the manufacture of thin-film photovoltaic devices. Cadmium and tellurium dissolution was achieved using hydrogen peroxide in dilute sulfuric acid. Leaching the scrap in 2.2 N H2SO4 yielded 99% Cd extraction and 98% Te extraction. Sulfur remained in the leach residue primarily in the elemental form. Elemental tellurium was precipitated from the leach liquor by adding Na2S2O5. Cadmium sulfate was recovered by evaporation. A preliminary process evaluation suggests that the process may have economic potential. Alternative recovery schemes are discussed.

Jan 1, 1995

By W. K. Connor, O&apos

The U.S. Bureau of Mines, in cooperation with the Idaho National Engineering Laboratory (INEL), conducted over 30 hours of melting tests to vitrify simulated low-level radioactive wastes from the INEL Radioactive Waste Management Complex (RWMC). Five separate waste compositions were investigated, each consisting of noncontarninated soil from the RWMC and surrogate materials used to simulate the actual buried wastes. The RWMC soil and five waste compositions were melted in a 50-lb, single-phase electric arc furnace with a water-cooled shell. These tests were conducted to determine melting parameters in preparation for a large-scale melting campaign to be conducted in the Bureau's 1-metric ton (mt), water-cooled-wall, 3-phase electric arc fumace. Bulk chemical composition was determined for each of the feed materials and for the slag, metal, fume solids, and offgas furnace products, and distributions were calculated for the key elements. The material balance for the furnace operation indicates that from 63 to 84 pct of the feed reported to the slag. Cerium, used as the surrogate for the radionuclides in the wastes, demonstrated an extremely strong affinity for the slag product. Although slag temperatures as low as 1250° C were recorded when melting the RWMC soil, temperatures in excess of 1600° C were necessary to achieve the fluidity required for a successful slag tap.

Jan 1, 1994

By T. C. Goel, A. Venna, R. G. Mendiratta

"Processing of ferrites has gained tremendous importance in recent times to meet the high performance demands on ferrites in keeping with the fast emerging· technologies. The quality of ferrite powders has strong influence on ·the performance of final device. Fabrication· of high performing ferrite components requires starting ferrite powders of precise stoichiometry, purity and microstructure. It is difficult to obtain these attributes by the conventional ceramic method. The key to obtaining quality powders lies in the· solution techniques. With this in view soft ferrites have been prepared by a wet chemical process, known as the citrate precursor method, which involves the formation of citrate complexes of the constituent cations. The advantages of this process are the ease of preparation and close control of composition, homogeneity, purity and particle size. Electrical and magnetic measurements on lithium ferrites have shown resistivity higher by more than two orders of magnitude compared to that observed for samples prepared by the conventional ceramic method, and low magnetic losses, making the ferrites specially suitable for high frequency applications.IntroductionProperties of ferrites are known to be sensitive to .their processing technique. A small deviation in the compositional stoichiometry of the ferrite affects its properties greatly. Soft ferrites such as Ni-Zn, Mn-Zn and Mg-Mn. are well known ferrites covering wide-ranging applications [1,2]. Lithiiim ferrites have also assumed technological importance for microwave applications and are potential substitutes for the expensive garnets [3]. Lithium ferrites are often doped with zinc to tailor the saturation magnetization required at high frequencies. Lithium and lithium-zinc ferrites, however, present difficulty to processing due to the volatile nature of both the cation components, namely Li and Zn. These ions are volatile at temperatures > 1000°C which makes their processing difficult. One of the main considerations of high frequency performance of ferrites is the high eddy current losses which prevent the interaction of the magnetic field with the ferrite component and hence impair device performance. These losses can be reduced by having a material of high resistivity. Electrical conductivity in lithium ferrite has been attributed to electron hopping [4] between the two vaience states of iron, Fe2+ <=> Fe3+, on octahedral sites. Maintaining the + 3 valence state of otahedral- Fe ions is thus a prerequisite for achieving high resistivity. The resistivity of ferrites is normally found to be low when processed by the conventional solid-state or the ceramic method [5]. This is attributed to (a) extensive ball-milling employed in the method to mix the component oxides results in non-stoichiometric compositions due to introduction of additional Fe ions on abrasion of steel balls during milling, (b) high processing temperatures involved which result in significant volatilization of Li and Zn ions creating thereby oxygen non-stoichiometry which results in reduction of Fe3 + to Fe2 +, (c) large and non-uniform grain sizes. In the present work, preparation of Li and Li-Zn ferrites by a non-conventional method known as a citrate precursor method [6, 7] which requires lower processing temperatures and duration is reported. The method gives stoichiometric compositions on account of homogeneous atomic-scale mixing of the constituent cations via the formation of metal-citrate complexes mixed in solution state. The method is also capable of giving small grain size which aids the oxidation ofFe2+ ions."

Jan 1, 2000

By Ben Q. Li

An efficient numerical algorithm for solving steady state heat transfer and solidification problems is described. The algorithm is of boundary integral type and is based on the formulation of the field variables along the boundary of the domain of interest. Compared with the familiar domain-based methods, such as the finite element and finite difference (or finite volume) methods, this boundary-based method has an advantage of solving fewer unknowns and hence has a potential for reducing computational time significantly. Another and yet more important advantage of the present algorithm is that it is a stable scheme and is not prone to numerical oscillations resulting from convective effects, as often encountered in the domain-based methods. Therefore, no numerical or artificial diffusion (such as streamline upwinding) is necessary. Numerical examples are presented that are drawn from processing systems for producing aluminum-based materials.

Jan 1, 1994

By Susana Caballero, Lourdes Yurramendi

Air Pollution Control (APC) ashes from Municipal Solid Waste Incineration (MSWI) plants need to be treated prior to landfilling due mainly to their heavy metals content. This research evaluates the capacity of the APC residues to sequester carbon dioxide, while the ash becomes stabilized for storage. It has the benefit of using two wastes, with no addition of any raw material. APC samples from different MSWI plants were treated by gas/solid accelerated carbonation at different temperatures and carbon dioxide concentrations to evaluate the residue behaviour to the process. The extent of carbonation was evaluated by means of weight gain upon carbonation and by the measurement of the final carbonate content. The APC residues were analyzed before and after the treatment in order to know their composition and their leaching behaviour according to the criteria for the acceptance of wastes at landfills established by the European Council Decision 2003/33/EC.

Jan 1, 2008

By F. E. Wagner, L. J. Cabri, Y. G. Safonov, N. S. Bortnikov, A. D. Genkin, J. Friedl, G. N. Gamyanin

"A multidisciplinary investigation (including INAA, SIMS, EPMA, and Mossbauer Spectroscopy) was used to characterize gold in four of the largest Siberian mesothermal sulfide gold deposits. These are the Olympiada (""'750 metric tons gold) and Veduga (estimated at 75-100 metric tons gold) deposits in the Enisei Mountain Range and the Nezhdaninskoye (z500 metric tons gold) and Sentachan deposits in the Verchoyansk-Kolyma area. It was found that some of the mineralization is refractory in all four deposits, largely due to the occurrence of ""invisible"" gold in arsenopyrite as well as within pyrite, but with a lesser concentration. The gold concentration and its distribution varies considerably both within and between arsenopyrite grains, with implications for processing options such as heap leaching. The ore most likely to be amenable to heap leaching is the oxidized ore of the #4 orebody of the Olympiada deposit, but further quantitative mineralogical investigations are recommended for this orebody's sulfide ore and for the ores of the Nezhdaninskoye deposit. Following a full mineralogical characterization, it is possible that economic viability will depend on a combination of pre-concentration with or without pre-treatment, followed by heap leaching of some tailings products.Acknowledgements· The Russian authors performed this study under an ""Eco res"" Project which was financially supported by the Ministry of Science and New Technology of the Russian Federation. C.J. Stanley wishes to thank John Spratt and Terry Williams for help with EPMA. F.E. Wagner acknowledges the Deutsche Forschungsgemeinschaft for a grant supporting the Mossbauer studies. L.J. Cabri is grateful to the following: M. Beaulne, D. Carson and J.H.G. Laflamme for technical support, K.E. Haque for technical comments, and D.M. Hausen and W. Petruk for editorial suggestions."

Jan 1, 1997

By Banqiu Wu

Zirconium carbide powder has been synthesized from zircon concentrate and methane using a high temperature plasma reactor, a non-transferred DC plasma torch was used as heat source. A high temperature filter consisting of graphite felt was designed, built and operated to separate the zirconium carbide from silicon carbide during the process. Characterization of the collected powders was done by wet chemical analysis using Atomic Absorption (AA), Scanning and Transmission Electron Microscopy (SEM and TEM) and by X-Ray Diffraction (XRD). It was found that the zirconium carbide purity was around 95% with silicon carbide being the primary impurity. The powders had particle sizes between 30 and 80 nm. The effect of several experimental variables are presented as well as temperature and velocity profiles calculated in the reactor.

Jan 1, 1997

By Wei Liu

A new process for extracting cadmium from the electric precipitated dust produced by ISP process was studied. A leaching rate of 89.1% of cadmium was attained by leaching the dust with NH3?H2O-(NH4)2SO4 system under the best leaching conditions: ratio of liquid to solid(l:s)=2.5, c(NH3):c(NH4+)=3:5, total concentration of ammonium and ammonia=8 mol?L-1, leaching time= 1.5h, temperature=35. The most troublesome impurity of lead could be deposited from the leached out solution automatically after put it static more than 15h when the total concentration of zinc and cadmium was up to 45gL-1 , and the final concentration of lead was 0.0047 gL-1, which meant 99% of it was removed. Metallic cadmium which contained cadmium more than 99% was prepared by electrowinning under the conditions: current density=750Am-2, total concentration of Cd2+ and Zn2+>25gL-1. The current efficiency was about 87% and the energy consumption for every ton of cadmium was about 548KWht-1. Main impurities of the metallic cadmium were copper and zinc and all of they could be got rid of in the following pyrometallurgical refining step.

Jan 1, 2006

By Qian Li, Haiyan Leng, Kuo-Chih Chou, Haoyuan Xiao, Zhigang Yu

Magnesium borohydride and Magnesium alanate were synthesized by mechanochemical metathesis reaction. The thermal decomposition behaviors of Mg(BH4)2-nMg(AlH4)2(n=0.5,1) systems were investigated as potential hydrogen storage materials. The results showed that the systems started to desorb H2 at 120 ℃ and desorbed 3.9 wt. and 4.9 wt.% H2 below 300 ℃ when n equals 0.5 and 1, respectively, while individual Mg(BH4)2 started to desorb H2 at 250 ℃ and desorbed only 0.82 wt.% H2. Because of the exist of the Mg(AlH4)2, the isothermal desorption kinetics of Mg(BH4)2 in the Mg(BH4)2-0.5Mg(AlH4)2 systems was 50% faster than that of pristine Mg(BH4)2. In addition, the re-hydrogenation rates also increased 49.4% and 37.9%.

Jan 1, 2015

By David Tisdale, Phillip Mackey, Nagendra Tripathi, Matthew Kreuh, Pascal Coursol

Xstrata Nickel’s Sudbury smelter operation is based on fluid bed roasting of Ni-Cu sulphide concentrate, followed by electric furnace reductive smelting and Peirce-Smith converting to produce a Bessemer matte for electro refining, along with sulphuric acid produced from smelter gas. While the site dates back to the 1930s, the present smelter configuration has been operational since 1978, and currently has a nominal capacity of about 67,000 tpy of contained nickel and is investigating options to expand in future up to 85,000 tpy. As part of a review of plant capacity options, a new metallurgical model of the plant was developed in order to examine a number of processing alternatives. Based on the METSIM™ platform, the present model includes the ability to examine the impact of a number of plant parameters on potential plant performance including; for example, the following: percent of sulphur elimination in roasting, matte grade, degree of matte metallization, temperature, coke requirements, sulphuric acid production, CO2 emissions and overall energy requirements. The process model also includes a number of special features adopted; for example, approaches to effectively model the complex Ni-Cu-Co-Fe-S-O matte system. This paper provides a description of the model and gives an overview of the results. As well as presenting the results of the present study, the applicability of this modeling approach to pyrometallurgical systems in general is also briefly discussed in the paper.

Jan 1, 2009

By E. Daniel Baker

"The term ""oxide disseminated gold deposits"" refers to near surface, gold-bearing veins, faults, and shear zones that typically contain appreciable amounts of oxidized ore or gossanous material, resulting from oxidation of sulphides.The concept of oxide gold deposits underwent a dramatic change after the discovery of the Carlin gold mine in north-central Nevada in the early 1960's. Now the term implies large tonnage, low-grade bulk minable deposits that are processed by milling and/or heap leach methods.Oxide gold deposits may now be classified into two types: (1) primacy ores derived directly from the effects of hydrothermal alteration on host rocks, and (2) secondary oxide ores derived from the supergene oxidizing effects of circulating post-mineral meteoric waters on gold-bearing sulphides. Each type of deposit has unique diagnostic mineralogic and metallurgical characteristics that must be addressed to achieve successful exploration strategies and viable metallurgical exploitation.The author would like to thank the management of Newmont Metallurgical Services and Newmont Mining Company for allowing presentation of this paper. Thanks are due Sevkett Acar, Donald M. Hausen, Jerry R. Odekirk, and D. Erik Spiller for their critical review of the manuscript. Also, thanks are extended to all those cited and uncited whose hard work and dedication have led to the discovery and exploitation of near-surface oxide gold deposits. Our knowledge would be greatly limited without the dedication and research of many others."

Jan 1, 1997

By Ryokichi Shimpo, Akio Fuwa

"The process-measurements of copper smelters in Japan were investigated for the summary of the latest technique and for the fundamental study of process control. The smelters investigated are those employing flash smelting furnace and P.S. converter, one reverberatory furnace and P.S. converter, and one continuous smelting converting furnace (M.I. process). Respective process is then considered, consisted of several reactors of different functions. The measurement methods were summarized in each reactor, including the measurement points. The methods of chemical analyses of the samples in each reactor were also investigated.IntroductionAn investigation on the process measurements, chemical analyses, and system control in copper smelters in Japan were carried out for understanding and summarizing the technique of the pyrometallurgical copper smelting operations. The typical seven processes in six copper smelters were investigated in the period from 1985 to 1987. The smelters investigated were Touyo Smelter of Sumitomo Metal Mining Co., Ltd., Kosaka Smelter of Dowa Mining Co., Ltd., Saganoseki Smelter of Nippon Mining Co., Ltd., Tamano Smelter of Hibi Kyodo Smelting Co., Ltd., Ashio Smelter of Furukawa Co., Ltd. and Naoshima Smelter of Mitsubishi Metal Co., Ltd. They include five flash smelting furnace and P.S. converter systems, one Mitsubishi continuous smelting and converting process (M.I. process), and one reverberatory furnace and P.S. converter system.The investigation was performed by making inquiries about the measurements, chemical analyses, system control, and their future prospects to the engineers in each smelter and by summarizing up in each item. The system control and future prospects were summarized in another paper titled ""Process Control Scheme of Copper Smelting Processes in Japan and Future View."

Jan 1, 1989

By G. Scavino

A 0.5 wt.% C, 22 wt.% Mn austenitic steel, recently proposed for fabricating automotive body structures by cold sheet forming, due to favorable overall strength and ductility, exhibits plastic localizations during uniaxial tensile tests, whereas no localization happens during biaxial Erichsen cupping tests. Full-thickness tensile and Erichsen specimens, cut from as-produced sheets, were polished and tested at different strain rates. During the tensile tests, the plastic localization phenomena consist first of macroscopic deformation bands traveling along the tensile axis, and then of series of stationary deformation bands, each adjacent to the preceding ones; both types of bands involve the full specimen width and yield macroscopically observable surface relief. No comparable surface relief was observed during the standard Erichsen tests. The stress state being known to influence plastic localization phenomena, reduced-width Erichsen tests were performed with 10 to 30 mm width polished specimens, in order to explore the transition from biaxial to uniaxial loading.

Jan 1, 2009

By Somayeh Dashti, Ehsan Vahidi, Fereshteh Rashchi

"The main goals in zinc electrowinning process are decreasing of power consumption and increasing of current efficiency. In this study, the electrowinning of zinc in the presence of different additives in electrolyte were established and Arabic Gum, Gelatine, sodium lauryl sulphate and l-hexyl-3-methylimidazolium hydrogen sulfate in the five levels using Taguchi method was examined. In our previous researches, using orthogonal array, effect of zinc electrowinning parameters such as anode type, current density, sulphuric acid concentration, temperature and zinc ion concentration was studied and the optimized conditions for zinc electrowinning was obtained. Anode composition: Pb-Ag 0.5%-Sn2%-Sb1%, current density (A/m2):500, acid concentration (g/1):165, temperature: 60°C, zinc ion concentration (g/1):70. The main goals in zinc electrowinning process are decreasing of power consumption and increasing of current efficiency. ln this research, the effect of four additives: Gum Arabic, Gelatine, sodium lauryl sulphate and an organic material in the four levels with Taguchi method was examined. ln fact the effect of electrolyte environment and determining the best electrolyte under the optimized conditions is the main aim of this study.IntroductionDue to its low cost and abundance, zinc is widely used in the production of brass, galvanized steel, sacrificed anodes and primary and secondary batteries [I]. Some 80% of world primary zinc production is derived via roast-leach-electrowinning processes [2-4]. In the electrowinning process to both improve final product quality and current efficiency the leachate should be purified [5].To produce zinc a current method is to extractit from acidic zinc sulphate solutions by electrolysis with aluminum cathodes and insoluble lead-based anodes [6]. Though the electrolytic processing of zinc has been performed for many years, there are still current efficiency problems in the cathodic process. These low efficiencies (88- 93%) have a serious impact on the costs associated with the energy consumption. On the other hand, these low efficiencies increase energy consumption and decrease the quality of the surface morphology [7- 8]."

Jan 1, 2012