Search Documents

By Yousef Mohassab, Manoranjan Misra, Monalisa Panda, Eman Wahbah

This work studies the removal of arsenic (V), arsenate, and arsenic (III), arsenite, from aqueous solution using calcined Quintinite-3T. The two adsorbents Quintinite-3T was prepared, calcined at different temperatures, and characterized by XRD, BET, and SEM. The surface area of the calcined Quintinite-3T was 193.4 m2/g. The particles size ranged from 12 to 56 nm for the uncalcined Quintinite-3T and from 24 to 42 nm for the calcined Quintinite-3T. Kinetic analysis, adsorption isotherm, and factors affecting the adsorption were investigated. Calcined Quintinite- 3T retained As(v) and did not release it back to water even after an entire month.

Jan 1, 2016

By W. G. Davenport

Chapters 19 and 20 examine direcHo-copper flash smelting and flash converting. This chapter compares the two processes and suggests which is likely to be 'the more economic for a given concentrate. It: (a) uses Chapter 19's direct-to-copper industrial oxygen and oil requirements (b) adds the energy required for electric furnace recovery of Cu from direct-to-copper slag (Czemecki et al 1999) (c) combines Chapter 20's, flash converting calculations with Chapter 18's flash smelting calculations to determine their combined industrial oxygen and hydrocarbon fuel requirements (d) adds the energy required to granulate, crush and dry flash smelting matte for the flash converter (e) adds the energy required to granulate and dry flash converter slag for recycle to flash smelting (f) compares direct-to-copper and flash smelting/flash converting in terms of their total equivalent hydrocarbon ener.gy requirements.

Jan 1, 2001

The results of laboratory, large-scale laboratory and commercial scale investigations regarding the process of slag melts cleaning by oxidizing-reduction gas mixtures with a wide range of Po2 and the use of matte of various compositions as an extracting phase are presented. The copper, nickel and cobalt behavior during the cleaning process has been studied based on SEM and x-ray Microprobe of the quenched slag melts. The general cleaning mechanisms have been found. On the basis of the obtained data the most efficient cleaning methods have been proposed.

Jan 1, 2003

By Xiaodi Huang, Matthew Andriese, Zheng Zhang, Jiann-Yang Hwang, Zhiwei Peng

"The thermal decomposition and regeneration behaviors of wüstite were investigated by in situ high temperature X-ray diffraction (HT-XRD) under non-isothermal condition at heating rate of 4 K min-1 in vacuum ranging from 294 K to 973 K. Wüstite on heating decomposes to magnetite and iron up to 823 K, above which it exhibits marked tendency to regenerate. Investigation of thermal stability of the reaction system shows that the decomposition proceeds under kinetic reaction control while the regeneration is under thermodynamic control. Kinetics study based on the Coats-Redfern integral approximation method indicates that the decomposition reaction follows a Komatsu-Uemura model-based diffusion-controlled kinetics with activation energy of 32.860 kJ mol-1. The thermodynamics analysis of regeneration reaction demonstrates that wüstite regenerates at lower temperature than stoichiometric ferrous oxide.IntroductionOwing to its importance in preparing various magnetic ceramic/metal nanocompostites or nanocrystals with high values of coercivity for the application as recording media, wüstite (non-stoichiometric ferrous oxide) has been attracting the attention of scientists over a long period [1-6]. The thermal behavior of wüstite was investigated by several researchers and phase transformations due to thermal decomposition and regeneration of wüstite during the heating in a specific temperature range was observed [7-9]. In spite of wüstite being found to dissociate to magnetite and iron at temperatures lower than 848 K and then regenerates at higher temperature, a clear understanding of the reaction mechanisms is clearly lacking [9]."

Jan 1, 2012

By W. Dresler

Design details of a 100 kVA DC electric-arc reduction furnace are described. The furnace is equipped with a 610 mm (24 inch) diameter graphite crucible hearth. A 76 mm (3 inch) diameter top graphite electrode is used as a cathode. The current passes through the bottom of the crucible and is carried to a bottom plate (the anode) by conductive magnesia carbon bricks. The furnace can be operated up to a maximum of 120 V, 1800 A, and presently 100 kW. The start-up operating experiences and metallurgical results of one reduction test with a Montana chromite containing 38% Cr2O3 are discussed.

Jan 1, 1994

By Shiwei Sun, Hongxu Li, Xiangxin Hao, Xie Yang

"Environmental impact assessment of copper metallurgical processes will soon become a compulsory activity in the future. The goal of this work is to analyses the copper metallurgical processes including pyro-metallurgy and hydrometallurgy based on the life cycle assessment method implemented in GaBi software. The evaluation indicators such as global warming potential (GWP), acidification potential (AP), photochemical ozone creation potential (POCP) and human toxic potential (HTP) are taken into account. The results show that the major environmental impact phase in pyro-metallurgy derives from beneficiation because of the largest material and energy consumption. It is also shown that copper hydrometallurgy has significantly lower environmental impact than pyro-metallurgy. Based on the evaluation results, some corresponding optimization methods are recommended to reduce environmental impact.IntroductionCopper is an important metal in modem society due to its wide variety of uses, including electrical wiring, heat exchangers, piping and roof construction and increasingly consumer electronics. Demand for copper has increased dramatically over the past decades, driving production rates almost exponentially. Annual production of copper was estimated to be 20 million tonnes in 2012 with Chinese production at about 6.06 million ton in 2012P1. The production process of copper has environment impacts that often go unnoticed by the producer. Higher production, coupled with declining ore grades, is placing increasing pressure on the natural environment.Sound environmental management helps producers improve their manufacturing technique. LCA is a well-established tool for assessing environmental impact potential and can be readily adapted to map impact potential over time, which can be used to quantify the environment impacts of a product or a process [21. This is achieved by creating an inventory of all the energy and material flows used in the process's life cycle. The results of an LCA can be used to improve the operation of a process so that they have less impact on the environment."

Jan 1, 2014

By Antrekowitsch Jürgen

The recycling of residues from metal producing by-products has become a main field of interest in metallurgical investigations. Forced by a stricter environmental legislation and the resulting increase of landfilling costs, combined with the aim to recover as many valuable metals as possible, a lot of different processes have been developed in the last two decades. Because of the high yearly tonnage residues from the iron and steel industry like slags, dusts and sludges have moved in the center of interest. Dusts from the steel mill, containing heavy metal oxides and halides did not play a considerable role as secondary raw materials for a long time. They even contain a huge amount of leachable elements and compounds which cause noticeable problems in case of a dumping. Nevertheless, the implementation of a new landfilling regulation, including a prohibition of aboveground dumping without inertisation, caused a rising interest concerning recycling technologies for such residues. In addition, the zinc content of these dusts became higher and higher and began to play the most important role for the economy of dust recycling.

Jan 1, 2006

By John J. J. Chen, Barry J. Welch

"As in many industrial processes, the detailed mechanisms involved must first be understood before being able to redesign, or to carry out improvements or optimisation of the process and equipment performance. In a great majority of metallurgical processes, visual observation and actual measurement of process variables are either very difficult or near impossible. Often, the cost and effort involved are prohibitive. Consequently, physical modelling is often used to provide some understanding of the process and for the validation of computer numerical models. In this paper, we summarise some of the work carried out at The University of Auckland on the modelling of the Hall-Héroult electrolytic cell, the in-line melt treatment process, and the steel casting tundish. IntroductionIn any industrial process, it is essential to understand the underlying mechanisms before any optimization or process improvement can be carried out. In many metallurgical operations, the processes are conducted at elevated temperature and under rather hostile environments. Consequently, it is often difficult, and sometimes impossible, to observe the actual processes occurring, or conduct measurements which are pertinent. In some situations, it is possible to formulate mathematical equations purported to describe the process, and obtain the solutions numerically. However, in this latter case, the validity of the simplifying assumptions made are often uncertain. Physical modelling may provide the necessary information for the validation of such numerical models. Furthermore, through an application of the principle of similitude, it is possible to apply data obtained from physical modelling to actual metallurgical processes. This paper will summarise some the work carried out at The University of Auckland on the physical modelling of gas-induced flow in the Hall-Héroult electrolytic cell, an in-line melt treatment unit, and the flow in a steel casting tundish.Gas-Induced Flows in a Hall-Héroult CellIn an aluminium cell, the effects due to electro-magnetic forces have been addressed and various design modifications such as magnetic shielding and the positioning of risers have been carried out to control or lninimise the effects of magnetic fields'. Consequently, the effects of gas-induced flows are now becoming significant providing the impetus for the study of the gas behaviour in the bath. Furthermore, the shape and size, and the rate of evacuation of the anodically generated gases affect the cell voltage affecting the energy efficiency; at the same time, the back-reaction between the anode gas and the metal produced is the predominant cause of the loss of current efficiency. Figure 1 shows a cross-section of a conventional cell in which the gas evolution occurs directly under the anodes, and the gas induced flow is confined mainly to the region occupied by the bath"

Jan 1, 1994

By cheng Peng-fei, TANG Hai-yan, guo Xiao-chen, LI Jing-she, Liang Yong-cang, Zhao Baojun

In the process of oxygen blast furnace, the lower coke ratio and the higher coke load make the skeleton coke more important. To understand the dissolution of coke in melting and dropping zone, the influence of FeO content, temperature and reaction time on the dissolution of coke with slag were studied by single-factor experiment. Meanwhile, the three factors and three levels orthogonal were conducted. The dissolution degrees were characterized by the weight loss ratio and diameter variation. The results showed that the weight loss ratio increased and the diameter decreased with the increase of FeO content, temperature and time. The three factors and three levels orthogonal test showed that time was the most significant factor on coke dissolution, FeO content of the second, and finally the temperature. The microstructure of coke after reaction indicated that the dissolution occurred on coke surface.

Jan 1, 2016

By Jie Li, Thomas A. Rawdanowicz, W. J. Collis, S. Venkatraman, S. Iyer

"InSb being the lowest band gap. material amongst the 111-V semiconductors with low effective mass has long attracted research interest, due to its potential application in far infrared devices and for high speed circuit elements. In this paper, we report, for the first time, Te-doping of InSb on GaAs substrate using SnTe doping source with molecular beam epitaxy (MBE) technique and its electrical characterization. The undoped epilayers are n-type in the temperature range of 10 K to 300 K investigated. The room temperature (RT) mobility as high as 64,810 cm2/V·s (1.9x1016 cm-3) have been measured on a 4.8 µm thick epilayer. Sn Te doping at different doping levels were investigated. 5. 7 µm thick doped layers with RT carrier concentrations ranging from 2x1016 cm-3 to 3.2x1018 cm-3 with corresponding full width at half maximum (FWHM) of x-ray (400) rocking curve varying from 170-200 arc-seconds have been achieved. The Hall mobility of 20,000 cm2/V·s at 1.3xl018 cm-3 carrier concentration was obtained indicating that SnTe is a good candidate as source material for n-type doping of InSb.IntroductionThe thin films of InSb and InSb-based alloys have found considerable interest because of potential applications in III-V semiconductor-based infrared optoelectronic devices1• In addition, the advantage of the small effective mass and the consequent high mobility can be utilized in high frequency and high-speed circuit devices2 InSb can also be used in magnetoresistive sensors for position sensing3. Epitaxial InSb films grown by MBE may be doped n-type with Si or Sn, or with the group VI elements, namely, S, Se, or Te. Of the group VI elements, Te may be advantageous because of its relatively low vapor pressure. However, the vapor pressure is high enough to have sufficient memory effect during MBE growth. Hence different telluride compounds such as GaTe45, PbTe6 and Sb2Te37 have been used as the dopant source for Sb-based compounds. SnTe has also been used as a successful n-type dopant in the MBE growth ofGaSb8 But, to our knowledge, there is no report on the investigation of SnTe doping of InSb. In this paper, we report the first doping characteristics of SnTe in InSb layers grown on GaAs substrate."

Jan 1, 1998

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Luciana Harue Yamane

"The present work investigated the effect of inoculums volume on bioleaching to recover metals from printed circuit boards using Acidithiobacillus ferrooxidans-LR. Printed circuit boards from obsolete computers were mechanically processed by comminution followed by magnetic separation, and the obtained non-magnetic fraction was used in the bioleaching experiments. A shake-flask study was carried out on the non-magnetic fraction samples using a rotary shaker at 30°C, 170 rpm and different volumes of oxidized culture solution as inoculums (%v/v): 5, 10, 20, 30, 40, 50 e 60. The oxidized culture solution was prepared inoculating pre-adapted bacteria Acidithiobacillus ferrooxidans-LR (5%v/v) in 200mL T&K medium. Leaching in acidic ferric sulphate was also performerd. The analyzed parameters were pH, ferrous iron concentration and metals analysis (AAS). The results showed that using 10%v/v of inoculums were extracted 99,2% of copper and 60% of aluminum by bioleaching. Zinc, lead and tin extraction were not influenced by bacterial leaching and extractions rate were obtained by chemical leaching promoted by acid medium. Ferric iron leaching extracted less copper (35%) than bioleaching. SEM analysis shown surface difference between samples of non-magnetic fraction before treatment and after bioleaching, showing corrosion pits formed by the bacteria contact.IntroductionWaste of electrical and electronic equipments (WEEE) has been target of discussion due to environmental, political and economical issues involved. Around 17 million of computers are discarded annually in the world due to malfunctioning equipment or because technologies become obsolete [1,2]. In contrast, only the central processing unit (CPU) of computers weights around 3kg. From this data, it can be calculated that 51 million kilograms of CPU waste are discarded yearly. This calculation was performed considering only the CPUs, disregarding the cathode ray tubes and liquid crystal displays of monitors [3,4]. Because of the amount that has been accumulated, e-waste has become a global problem but also can be an alternative source to recover valuable materials [5,6]."

Jan 1, 2012

By M. A. Gimenes

The utilization of chlorination in extractive metallurgy and advanced ceramics areas has been widely investigated as a preparative route in order to obtain intermetallic compounds, which are used as precursors in the development of new materials and process. The major processes of decomposition of rare-earth ores use sulfuric acid and sodium hydroxide at high temperatures, however there is not much work concerning chlorination. In this work, a systematic study of the reaction between xenotime (REPO4), chlorine and carbon has been performed. Particular emphasis was on kinetic studies to establish optimized conditions for the reaction. The kinetics of chlorination of xenotime raw material by rare-earth elements/compounds has been studied over a temperature range from 600°C to 950°C. The influence on the rate of conversion of xenotime to RECl3 on temperature, partial pressure of chlorine, carbon content, and particle size were investigated. A global rate equation that includes these parameters has been developed. The results show that the process follows the unreacted core-shrinking model with a formation of a porous product layer. The powder X ray-diffraction technique corroborated this model showing clearly the patterns related to the formation of yttrium oxychloride (YOCl), indicating that the reaction mechanism involves the presence ofan intermediate step before the formation of lanthanide chloride.

Jan 1, 2000

By LeoJ. Miller

Exploration for an ore deposit commences with an outline of the regional ore controlling environment and is followed by the application of tools to focus the target area. One of the most essential focusing is the mapping of the mineral assemblages within the area of the ore. Key elements of mineralizing fluids, either epigenetic or syngenetic, enter into mineral assemblages that extend far beyond ore deposits. Portions of these assemblages may consist of new matrix minerals or alteration of previously existing minerals. Today, ore deposits are divided into genetic classes and each class is d8fined by a specific geological environment. Ore deposits within a given class are associated with a mineralogy, that is characteristic of the ore deposit class. So faithful is the mineral assemblage surrounding, or within an ore deposit, that recognition of the assemblage may be sufficient to define the class. Porphyry copper deposits have long been noted for their halos of alter-ation minerals. The outermost ring of chlorite, epidote and calcite extend thousands of feet away from the main ore zone. The mineral associated with porphyry copper deposits have been well documented by our distinguished speaker Paul Kerr, at Santa Rita (1), and Silver Bell' (2), and by excellent papers from S. C. Creasey, 1959 (3), Sales, 1948 (4), T. S. Lovering, 1949 (5), our Co-Chairman John Guilbert, 1970 (6), and many others. Several recent porphyry copper mines have been discovered in recent years by utilizing the mineral assemblage model described by Lowell and Guilbert, 1970 (6). Dave Lowell applied his own model of mineral halos for the discovery of Kalamazoo at San Manuel (7), Arizona, and Casa Grande West, Arizona. The purpose of this paper is to outline the application of mineralogy for discoveries of deposits other than porphyry copper mines and in particular, to ore discoveries in which mineralogy has played a key roll.

Jan 1, 1981

By Zhijing Zhang

The management of hazardous wastes is important in a society which is increasingly concerned with environmental issues. Incinerators such as the slagging rotary kiln are widely used in the treatment of hazardous wastes. However, in order to assure a smooth operation of the rotary kiln, the melt should have both a low melting point and high fluidity. In this study, the fluidity of various hazardous waste rotary kiln slags was measured in terms of length of flow using the crucible test technique. It was found that the slags have melting points ranging from 1372 to 1424°C while their fluidities varied from 61-102 mm. The effect of addition of oxides on the fluidity of a slag containing 47 wt% SiO2 was also investigated. For this slag, additions of SiO2 (up to 56 wt%), FeO and Na20 increased fluidity, whereas the addition of CaO and A1203 resulted in lower fluidity values.

Jan 1, 2002

By S. P. Mathew

The ISASMELT Lead Process is a continuous two stage process for the production of crude lead from concentrate. It is based on the use of a top entry submerged Sirosmelt lance to produce turbulent baths in which high intensity smelting or reduction reactions can occur. The process involves oxidizing the concentrates in the first stage to produce a high lead slag. This slag is tapped continuously and transferred down a launder to a second furnace where it is reduced with coal. Crude lead and discard slag are tapped continuously from this furnace through a single taphole and separated in a conventional forehearth. Process and engineering design work for a commercial scale Lead ISASKELT plant designed to produce 60000 tpa crude lead has been completed. This plant is planned to be operational in 1991.

Jan 1, 1990

By I. Gaballah

About forty percent of the SOx emissions are generated during the processing of metal sulfides of Cu, Pb, Zn, Ni, etc. Although new technologies for metal sulfide's smelting allow the production of H2S04 with a reasonable cost and decrease the emissions of sulfur oxides, the generated quantity of SOx is considered as a serious threat to environment. This paper suggests alternatives for low temperature processing of complex sulfide ores or concentrates 'CSO or CSC' under neutral, reducing and chlorinating atmospheres or their combination. At T > 400 "C, The neutral and reducing treatments allow the decomposition of pyrite and the partial recovery of sulfur as So and H2S. At 300 "C, the chlorinating treatment of CSC is fast, exothermic and allows the separation of FeC13 from the valuable elements' chlorides. It also generates SyCIx that can be either reduced by H2 or hydrolyzed in presence of sodium sulfide. The recovery rate of elemental sulfur with respect to the sulfur input exceeds 90 %.

Jan 1, 1999

By Adrien Antenen, Didier Villette

CITRON has developed a new process for the recycling of hydroxide sludge, household batteries, catalysts, automobile shredding residues, grinding sludge and other metal containing organic and inorganic waste. A pilot plant with a capacity of 1,000 tons per year has started operations in April 1998. In August 1999, an industrial plant became operational with an initial treatment capacity of 23,000 tons.

Jan 1, 2000

By Satu Strömberg

Four different nickel concentrates were oxidized in a laboratory scale laminar flow furnace in simulated flash smelting conditions. The major nickel- and iron-bearing minerals in the con- centrates were pentlandite, violarite, gersdorffite, and pyrite and pyrrhotite, respectively. Thermal decomposition, ignition and oxidation behavior of nickel and iron sulfides were examined by using optical and scanning electron microscopy. General reactivity of the concentrates was monitored with sulfur removal which was most effective in violarite-based concentrate. Pentlandite-concentrates needed higher experimental temperatures for complete desulfurization and gersdorffite-based concentrate contained 5 - 10 % of the original sulfur even in the most oxidizing conditions studied (1 100°C, 50 vol-% 02). The reactivity of the iron minerals was found to depend on the other minerals present in the concentrate. In this paper, the observed re- action products and mineralogical changes are presented and preliminary conclusions of possible reaction mechanisms of nickel-bearing minerals are discussed.

Jan 1, 1997

By Jürgen Antrekowitsch, Thomas Griessacher

The recovery of valuable metals from residues like dusts and sludges is nowadays state of the art. Depending on the complex constitution, a recovery of different metals can – in the majority of cases – only be performed with considerable energy input in high temperature processes together with insufficient yields and newly generated residues. Often, the behavior of the dust or sludge in the process during melting or reduction is unknown. In this work, a detailed characterization of selected residues like steel mill filter dusts, cupola furnace dusts and leaching residues is done. The different steps of getting from solid particles into a homogenous liquid phase were investigated. Although high temperature processing leads to high reaction speeds, the complexity of residues keeps the system away from thermodynamic equilibrium. With this research program, some basics are generated to understand smelting and reduction and the gap between thermodynamical calculations and real behavior can be explained.

Jan 1, 2008

By M. C. Esposito

Seven pyrite samples purified from coal sources and one ore source pyrite (for comparative purposes) have been characterized by chemical and mineralogical analyses, inherent floatability, apparent specific gravity, surface area, semiconductor type, optical anisotropy, dissolution and oxidation rate. The data clearly demonstrate that pyrites from various coal sources differ not only from ore pyrite but from each other as well.

Jan 1, 1987