Search Documents

By Axel Preusse

To detect improper deformations of a roof bolted roadway in order to reduce inner mine damages in the most early stage and to initiate suitable countermeasures if necessary, several different measurement systems were used for monitoring a roadway's stability on the hardcoal mine "Auguste Victoria" (DSK AG). In this paper the different convergence measurement procedures are described and their respective results are introduced. Subsequently the results of the single measurement methods and procedures are correlated with each other.

Jan 1, 2000

By Radoslaw L. Michalowski

The operation of mobile mining equipment near the crest of stockpiles and wastedumps often results in localized slope failures. The Bureau of Mines has developed a computer code based on a rigorous limit plasticity approach which determines the admissible total weight for a concentrated loading near the crest of these otherwise stable structures. The program is based on a three- dimensional analysis and provides an upper bound solution to the load that can be applied to the top of the operating distances for mobile equipment from the slope edge. This presentation will discuss the application of limit plasticity to the development of the local three-dimensional collapse mechanism, and the use of the computer code based on this approach for mining applications.

Jan 1, 1990

By Y. P. Chugh

About 60-70% of the underground mined coal in Illinois is extracted using a room-and-pillar mining method that permits extraction of about 50% of the coal. The remaining coal is left behind in the form of support pillars to control surface and subsurface movements. Illinois coal seams are typically associated with water sensitive weak floor strata whose thickness varies 0.31 - 1.3 m. The current mining geometry mostly uses pillars of constant size within a mining area. This traditional practice suffers from the disadvantage that pillars within the center region are subject to much higher loads than the pillars located on the outer edges of the panel. This results in a higher incidence of rib spalling, and roof falls, creating a potentially hazardous work environment. In addition, this concentration of loading at the center of the panel provides initiation points for floor failure to occur. The primary goal of this study was to reduce ground control problems and production costs in Illinois mines by considering alternate mining geometries. The development and subsequent field demonstration of an alternate geometry is presented in this paper.

Jan 1, 2004

By Thomas Barczak

Pumpable roof supports provide an alternative longwall tailgate roof support and have grown in usage during the past few years. Heintzmann Corporation has been installing pumpable roof supports at the RAG Resources Emerald Mine in western PA since 1998, where they have provided effective roof control in their longwall tailgates. Despite the success of these supports in this application, questions remain regarding critical design issues for optimizing the use of this support technology. The support loading profile is characterized by a high initial stiffness with peak loading occurring at less than one inch of convergence, followed by significant load shedding with a post failure capacity comparable to that of wood cribbing. Therefore, the key to optimizing the support utilization is to provide sufficient load density to prevent convergence from occurring beyond the peak loading capacity. This requires an understanding of how the supports interact with the ground conditions, hence measurement of the ground reaction curve. In order to obtain this information, pumpable roof supports were instrumented to measure support loading. Roof deformation and roof-to-floor convergence measurements in the vicinity of the instrumented supports were also made. The experimental parameters for the installation were the support spacing and water¬to-solids ratio of the grout, which controls the grout strength and ultimately the maximum capacity of the support. The study clearly shows that at this mine a 24-inch diameter support is fully capable of providing adequate ground control under depths of cover of 750 ft as only 50 pct of the available support capacity was utilized outby the longwall face. It was also shown that the 2.00 to 1 water¬solids ratio, despite providing a slightly softer support response, is sufficient for maintaining the same degree of roof control provided by the traditional 1.75 to 1 grout mix. The 10-ft spacing of the supports did not cause any ground control problems outby the face. However, inby the face the performance of the support is degraded once the peak capacity of the supports is exceeded. It appears that the large load shedding behavior, which is characteristic of this support following peak loading, allows the immediate roof to separate. When this happens, the support is unable to regain control of the roof in time to prevent failure of the immediate roof beam.

Jan 1, 2003

By D. Reddish

The combination of free standing steel supports, such as arches, and rock bolts (mixed support) has Frequently been in used in UK coal mine roadways when it is considered that the strata and/or environmental conditions would not be suitable for rock bolts solely. However, how such mixed support systems operate is not fully understood. Due to the differences in the support method provided by rock bolts and free standing steel, the total support generated is not simply a case of adding the contribution to the support of the roadway given by the two systems. This paper describes a numerical investigation into mixed support systems when used in coal mine roadways. A series of 2D and 3D geomechanical models are described and the method of modelling the rock bolts and steel supports in coal mine tunnels is discussed. The numerical models described include rock boltd only roadways, steel supported roadways and mixed supported roadways in a variety of geological and in-situ stress conditions. Conclusions are formed that allow an insight into mechanisms of strata reinforcement provided by the support systems modelled. Further to this, a review of the numerical modelling of pre-tensioned rock bolted systems is described identifying the contribution to support efficiency given by the adoption of tensioning in full column resin anchors. The results obtained highlight that the effectiveness of the pre-tensioned load is dependant on the rock mass quality and in- situ stress level at the site where it is to be used.

Jan 1, 2004

By Hanjie Chen

Mining experiences have shown that in a pitching seam, roof behavior is significantly different from a flat seam. Uphill mining usually experiences more roof problems than downhill mining. Based on a case study at RAG American Coal Company, Willow Creek Mine, this paper presents the roof control problems experienced in a high pitching seam. Then, finite element modeling is conducted to analyze the roof stress distribution for an entry developed in different directions relative to the seam strike. The results shows that seam inclination has a significant effect on roof stability in terms of tensile stress. Uphill mining experiences higher tensile stress than downhill mining. The modeling technique utilized in this analysis presents a first of kind methodology.

Jan 1, 2000

By Peter Altounyan

Goedehoop Colliery in the Witbank Coalfield of South Africa produces some 8 million tonnes of coal from fully mechanised room and pillar mining methods, using resin anchored bolts as roof support. Investigation of the quality of the installed bolts resulted in the finding that it was possible to pull out fully encapsulated roofbolts. This led to a drive to improve the quality of installation by making it easier to install a roofbolt correctly and more difficult to install incorrectly, whilst at the same time achieving high bond strength. The method of installation which was investigated, developed and implemented is known as 'spin to stall.' The roofbolt is pushed through the resin capsule to the top of the hole and then spun to mix the resin, until the increasing resistance to rotation exceeds the breakout limit on the bolt torque nut. The nut then runs up the bolt thread and is tightened to the roof as the drill stalls. This procedure is simple and avoids human factors such as non adherence to 'spin' and 'wait' times which contribute to poor installation with conventional methods. However spin to stall installation has been avoided in the past because of concerns over damage to the resin bond. This paper reports on the efforts made to investigate and understand the factors involved, and the progress made in overcoming the problem of resin damage so that the advantages of this installation method can be realised.

Jan 1, 2003

By Yong-Ming Jiang

Longwall mining systems are extremely complex and expensive and require great caution for reliable and efficient operation. In many cases, ground control problems are the primary concern in longwall mining. For example, unexpected threats such as roof falls or shield damage can cause sudden interruption of coal production and safety problems, which can originate from many parameters such as shield capacity, setting load, shield type, conditions of immediate and main roofs, pillar stability, geological anomalies, etc. However, it is difficult to correlate ground-control problems at a longwall face with the related mining and geological factors. In this paper, a method of correlation analysis, called tree classification, which permits the use of a large and variable number of features, is introduced The method provides an effective approach to produce an accurate classifier or uncover a knowledge structure, which will be used to predict future consequences depending on past and current data sets. The application of the tree classification method in longwall stability analysis is discussed, and the major procedures of constructing a knowledge structure are included as an example utilizing monitored leg pressure data in a longwall face. Also, the importance and ranking of the variables related lo longwall shield stability is discussed This is a major step towards developing an artificial intelligence system for real-time interpretation of shield monitoring data and hazard prevention.

Jan 1, 1993

By Benjamin Mirabile

"Current and emerging practices to ventilate longwall gobs are prompting increased design and analysis of standing support requirements related to longwall mining. Specifically, additional design methodologies are being employed to evaluate standing supports in the #2 entry of a 3-entry longwall system.Numerical modeling will be used to evaluate the performance of standing support in the #2 entry between gobs of longwalls in the Herrin No. 6 seam. The performance of standing support in the #2 entry will be evaluated based on the following: (1) The effectiveness of standing support in maintaining an open airway in the #2 entry; (2) The interaction of standing support in the #2 entry with standing support in the longwall tailgate; and (3) Loading conditions of longwall pillars. Initial numerical modeling activities are focused on evaluating the roof to floor convergence in the #2 Entry and using the ground reaction curve concept for support design.Numerical modeling indicates that, like standing support in tailgates, supports in the #2 entry require some type of yield mechanism to withstand initial uncontrolled convergence. Numerical modeling also suggests that support density can be lower than that used in a tailgate support application. The numerical models used for initial investigation of support performance in the #2 entry are limited in their ability to evaluate support performance. The magnitude of uncontrollable convergence can be estimated with LaModel software. Near-seam conditions have not been investigated in this research since the LaModel software does not have the ability to evaluate inelastic rock behavior.IntroductionDuring the past three decades, many researchers have investigated standing support performance in longwall tailgate entries. Very little attention was paid to the middle entry of a threeentry longwall gateroad. As longwalls retreated, no personnel would travel the #2 entry, and the entry was considered part of the longwall gob. In response to recent mine disasters, regulatory agencies and operators have devoted more attention to these entries. Prior to the Upper Big Branch mine disaster, little or no secondary support was applied in these entries. Unlike secondary support in longwall tailgates, there is little empirical knowledge or quantified research specifically applied to secondary support in the #2 entry. This paper outlines initial steps used to develop a design methodology for secondary support in the #2 entry."

Jan 1, 2015

By Thomas M. Barczak

A theoretical evaluation of the impact of horizontal load on shield support capacity is made from a static rigid body analysis of the shield structure. Parameters affecting horizontal support resistance are investigated for a typical too-leg shield design. Horizontal forces acting on a roof support element are found to be both roof-generated and shield-generated. The impact of shield-generated horizontal forces on roof strata is also discussed from a theoretical viewpoint in relation to desired ground control. A technique is described whereby horizontal loading of shield supports can be measured underground. Horizontal load measurements from two different longwall faces were found to be significant, ranging from 20-35 pct of measured vertical load.

Jan 1, 1984

By Aarao de Andrade Lima

Mechanical properties typical of coal are used in the comparisons of pillar strengths based on finite elements and the empirical equations of Holland-Gaddy, Salamon-Munro, Obert¬Duvall, and Bieniawski-PSU. A correlation among the strength parameters which are employed in the empirical equations, in Mohr-Coulomb and Hoek-Brown failure criteria is established. Emphasis is given to the important distinction between the mechanical properties of small rock specimens and those related to the rock mass. An elastoplastic version of Hoek-Brown criteria has been developed and implemented in a finite elements code. The strengths calculated using the empirical equations showed a good agreement when the ratio width by height of the pillars varied from I to 8, except for Holland-Gaddy equation which exhibited lower values. Under the hypothesis of associative perfect elastoplasticity used, pillar strength calculated using Mohr¬Coulomb yield criterion became excessively high for all the models having a pillar width by height ratio above 2. The finite elements solution based on Hoek-Brown criterion predicted strengths around fifty percent larger than Bieniawski-PSU equation when the pillars width by height ration varied from 3 to 8, showing good agreement below that range. It has been concluded that, under the hypothesis of percfect plasticity, stress analysis techniques may overestimate the strength of rock structures subjected to high confining stresses.

Jan 1, 1997

By Andre Vervoort

The roof in coal room and pillar panels is normally stratified and can be thought of as beams or plates supported by the pillar sides in the roadways and by pillar corners in the intersections Underground measurements showed the effect of the face advance on the additional total movement of the roof skin and on the relative movement between various layers in the roof. The latter consists of the opening of bedding planes and of the lateral sliding of layers over one another. Both phenomena increase locally the axial load along full column anchors. Four models have been used to come to a better understanding of the roof behavior: a beam either clamped above the pillar side or laying on the pillar sides and a three-dimensional boundary clement model with and without bedding planes. The shape ref the curvature of the roof deflection is host approached by a clamped beam: the other models overestimate the movement at the sides. The largest roof deflection for a given Young's modulus is estimated by the model incorporating bedding planes. This model estimates that the bed separation occurs close to the face (within the first meter) and within 0.2 m of the sidewalk. In some simulations, openings are even recorded just ahead of the face. Further underground measurements should focus on these findings, as the effectiveness of the support is directly related to the amount of bed separation and sliding, which have occurred prior to the support installation and which still cart occur abler installation.

Jan 1, 2000

By Khaled Morsy

Most of the available numerical codes simulating the reinforcing effect of fully grouted bolt are accomplished by a series of bar elements which are connected along their length to the host rock by shear springs and sliders. The spring-slider system represents the shear bonding effect between the bolt and the host rock. This paper describes a three dimensional finite element modeling technique for the 3D simulation of fully grouted bolt reinforcement. The proposed technique introduced a physical simulation for the fully grouted bolts. The bolt simulation is composed of a series of beam elements (representing the steel rebar) embedded in brick elements (representing the grout). Because of the complexity of the grout/rock interface, ABAQUS explicit code was used. A modification of the ABAQUS default friction model was conducted to consider the cohesion of the grout/rock interface. The interaction between the grout and the host rock is simulated by the modified friction model. To verify the proposed technique, a simulation of the pull out test we conducted. The results from the simulation were compared with former studies

Jan 1, 2004

By Collin L. Stewart

A summary of the results of a limited subsidence monitoring program at Cyprus Amax Coal Company's Shoshone Mine No. 1 in the Hanna Basin of south central Wyoming is presented. The monitoring program was designed to meet regulatory requirements for confirmation of subsidence predictions made in the mining permit. The longwall panels were 380 ft to 600-ft wide. Mining heights varied from 11 ft to 13.5 ft. Gate road development included three-entry and two-entry head and tail gates. Overburden depth varied from 150 to 945 ft. The coal seam and overburden dip at approximately 11 degrees. The overburden is very low to low strength mudstone and carbonaceous shale with low to moderate strength, silty sandstone interbeds. Panel W/h ratios varied from subcritical to supercritical. Smax was 0.9 of the mining height. The subsidence ratio was about 0.6 for subcritical width. The draw angle on the up-dip side averaged 20 deg. The draw angle on the down-dip side averaged 12 deg.

Jan 1, 1995

By Mietek Rataj

Installation of pre-tensioned Strand Bolts i.e. resin grouted cable bolts is very common now in Australian coal mines. A short historical development of this type of rock reinforcement is outlined Various systems have been developed to apply 20 to 25 tonnes of pre-load to these bolts but there are still some technical problems which have to be overcome. One of the major problems encountered is bleed off tension which is highly undesirable as required "over loading" rocks the immediate roof thus inducing fractures iii weak strata. The major reason for the loss of tension apart from the design of the tensioning jack, is the design of the conventionally used barrels and wedges. Due to a roof plate tilting during tensioning the cable moves out of the barrel centre which impedes proper positioning of the wedges and subsequent excessive return of the cable once load of the jack is released. This problem has been largely resolved by the design of a special barrel having a centralizing rim allowing for significant reduction of the toss of tension. KEYWORDS: Pre-tensioned Strand Bolts, Cable Bolts, Bleed off Tension, Tensioning Jack, Loss of Tension

Jan 1, 2002

By D. N. Cleaver

Like other influence function methods, the SWIFT subsidence prediction program, developed within the Mineral Resources Engineering Department at the University of Nottingham, requires calibration to regional data in order to produce accurate predictions of ground movements. Previously, this software had been solely calibrated to give results consistent with the Subsidence Engineer's Handbook (NCB, 1975). This approach was satisfactory for the majority of cases based in the United Kingdom, upon which the calibration was based. However, in certain circumstances within the UK and, almost always, in overseas case studies, the predictions did not correspond to observed patterns of ground movement. Therefore, in order that SWIFT, and other subsidence prediction packages, can be considered more universal, an improved and adaptable method of regional calibration must be incorporated. This paper describes the analysis of a large database of case histories from the UK industry and international publications. Observed maximum subsidence, mining geometry and Geological Index for several hundred cases have been statistically analysed in terms of developing prediction models. The models developed can more accurately predict maximum subsidence than previously used systems but also, are capable of indicating the likely range of prediction error to a certain degree of probability. Finally, the paper illustrates how this statistical approach can be incorporated as a calibration system for the influence function program, SWIFT.

Jan 1, 1995

By George Gardner

The rapid growth of highwall mining in the Appalachian coalfields has resulted in unique safety concerns. Due to the concentration of activity at the base of the highwall and the potentially destabilizing influence of the mining process, proper mine planning and continual monitoring of the ground conditions is essential to ensure a safe and productive operation. This will also help to minimize the need to recover equipment that has become entrapped underground, and the subsequent hazards associated with a recovery operation. Adequate geotechnical site investigation and rational design methods should enable mine planners to properly account for the site-specific conditions that influence web and abutment pillar, roof, floor, and highwall stability. This paper examines the growth of highwall mining, provides a general overview of the various safety concerns, and reviews the modes of highwall failure as they relate to a highwall mining operation. Gcotechnical considerations that should be taken into account before and throughout the mining operation are emphasized. The importance of closely examining and monitoring highwall conditions for subtle signs of highwall instability will be discussed.

Jan 1, 2002

By Graham Daws

The introduction of UK rock bolting technology has been applied in many large underground coal mines around the world. This paper explains the methods that have been applied for its successful introduction and discusses several case studies. It does not give fine detail but is intended to allow decision makers to gain a basic understanding of the method used to introduce rock bolting to a mine.

Jan 1, 2011

By E. Hosca

Alternative tailgate loading conditions due to conventional and conventional/yield pillar combinations were evaluated to define roof loading. In order to isolate different loading situations, the tailgate entry was considered as part of the roof-pillar-floor system, which is controlled largely by the structural integrity of each member. A data bank of case studies was compiled, which contains details of roof and floor lithology, structure, support, and mining data, including any failure modes. The range of loading conditions that any tailgate can be subjected to was identified to form the basis of numerical modeling. Numerical modeling was then conducted on tailgate openings to determine roof, floor, and rib responses, including failure modes to a variety of loading conditions. Trends developed from the numerical modeling were modified using field data to form the basis for support evaluation and application. The effects of support were modeled numerically to determine optimum load capacity and points of application for reducing the potential for entry failure.

Jan 1, 1994

By Daniel W. H. Su

Thick, massive sandstone present in close proximity of the mining horizon can create difficult longwall caving issues, which may lead to severe face loading and subsequent face roof control problems. Under deep cover, such delayed caving and overhang not only impose additional loading on the gate road pillar system, but they also increase the potential for large seismic events. Such a combination of thick, massive sandstone geology and deep cover was present over a portion of a southwestern Virginia coal mine, which was confirmed via detailed in-mine roof scoping and mapping. Large seismic events were recorded over a district of 1,000-foot-wide longwall panels. This paper presents the ground control design changes implemented to reduce longwall-induced stresses in the sandstone, to reduce longwall abutment pressures in the gate road pillars, and to reduce the magnitude of mining-induced seismic events. A series of two-dimensional finite element models were constructed and analyzed to evaluate the longwall-induced stresses in the sandstone above the gate road pillars and the abutment pressures within the gate road pillars. Results from the analyses indicated that reducing the panel width from 1,000 to 700 feet reduced the longwall-induced stresses in the sandstone by a factor of 2.0. Specifically the probability of sandstone stability improved from 29% for the 1,000-foot-wide panel district to over 95% for the 700-foot-wide panel districts. Also, the subcritical 700-foot-wide panel, coupled with a change in pillar design, considerably reduced the longwall-induced abutment pressures in the gate road pillars, which significantly increased the gate road pillar stability factor. Surface subsidence measurements conducted over the 1,000-foot-wide panel district and two new 700-foot-wide panel districts were in very good agreement with those predicted by the finite element models. In addition, results from the models indicated that wider panels with a smaller district may produce the same probability of sandstone stability. One four-panel district and one five-panel district with the new ground control design changes have been mined successfully. The panel width was found to be the most influential factor in determining the longwall-induced stresses in the sandstone and in the gate road pillars. The thickness and massive nature of the sandstone, the proximity of the sandstone, and the strength of the sandstone were also found to be important factors. Seismic monitoring over the two mining districts that employed 700-foot-wide panels confirmed the reduction of one order of seismic magnitude when compared with those measured over the 1,000-foot-wide panel district.

Jan 1, 2014