Search Documents

By Vincent Scovazzo

Cost-effective underground mine configurations have been designed in highly fractured rock masses where the stone possesses a high material strength. A limestone mine in the eastern United States is used to demonstrate procedures for the geotechnical design of one such operation. The mine discussed is located in both limbs and the axis of a recumbent fold that fractured the rock mass. In a highly fractured rock mass, where the host rock has high strength, a design can be developed to alleviate intact rock failure. This is possible because in most cases as the stress levels needed for intact failures are approached, the stresses are quickly dissipated due to movement along discontinuities, which represent planes of weakness. As a result most underground failures in highly fractured rock are due to sliding or toppling. Even when intact rock fails in a highly fractured rock mass, it is the movement along an existing joint or other weakness plane that often initiates or causes this failure. It is therefore important to obtain the characteristics of weakness planes that are the discontinuities within the mass. The required information on weakness planes, geology, and strength of materials is discussed and recommendations for obtaining this information are presented. A discussion is provided on failure modes and the use of developed information for their evaluation. The impact on geotechnical design is demonstrated through pillar sizing procedures; however, this approach can also be applied to mine roof and pillar foundations.

Jan 1, 2002

By Hamid Maleki

Results of geologic investigations, in-mine instrumentation, and numerical modeling are presented for two longwall mines in which pillars with large width-to-height ratios (8 to 9) are used. These investigations revealed that wide pillars unload when subjected to sufficient stress and that pillar unloading is influenced by geologic conditions. Field measurements in mine 1 clearly indicated load transfer from the longwall area toward the gate roads, resulting in pillar failure near the margin of a fluvial channel. Loads were shown to transfer to a harrier pillar (width height ratio equal to 9), contributing to progressive failure of this pillar. Unloading of the barrier pillar was associated with significant load transfer to the two-seam submains to the north of the harrier, contributing to roof falls, floor heave, and rib spalling within the submains. Stress analysis results addressed pillar peak strength and unloading behavior that was in agreement with the measurements and underground observations. Underground observations and stress analyses were completed before and after longwall mining near a six-entry submain in mine 2. This submain was intended to he used as a temporary bleeder and tailgate for a small longwall block consisting of one to two panels, depending on the development schedule in other areas of the trine and observed ground conditions. Numerical modeling using both elastic and inelastic pillar behavior for submain pillars with a width-to-height ratio of 8 was completed before mining began. Results indicated that pillar unloading was likely. During retreat of the first longwall panel, pillars unloaded. as evidenced by progressive rib spalling along the cleats, This behavior was mostly confined to the immediate face area, an observation that was in agreement with the modeling results,

Jan 1, 2000

By John Cassie

The condition of roadways in the Deep Main seam at Asfordby mine, operated by RJB Mining (UK) Ltd, is strongly dependant on drivage direction relative to the maximum horizontal stress. The mine is laid out with gate roads driven approximately parallel to the maximum horizontal stress giving favourable drivage conditions. This has led to particulary difficult conditions for face installation headings which have to be driven to an increased width and at a high angle to the horizontal stress. A solution to the formation of face headings is described making use of stress relief with the face heading being driven in the zone of reduced stress surrounding a previous heading. In implementing this solution use was made of results from computer modelling and detailed monitoring of roadway behaviour. High reinforcement densities including cable bolts were used in supporting the headings. The experience provides an example of a traditional technique being applied more scientifically. The results obtained demonstrate the effect of stress relief and reinforcement methods in altering drivage conditions and suggest possible alternative strategies for the formation of future face headings in these conditions.

Jan 1, 1997

By Alan Campoli

Approximately 100 million fully grouted rebar roof bolts are installed each year in the United States, 80% are B-Series (5/8 inch fully grouted rebar in a one-inch borehole). The lesser used more expensive A-Series (3/4-inch fully grouted rebar in a one-inch borehole) maximizes resin performance. Standard B-Series provides only 60% of the pull out resistance of A-Series. The Eclipse System was developed by Minova USA Inc. and marketed with Excel Mining Systems to improve the performance of B-Series. A 1/8-inch offset bolt head combined with a specially formulated Eclipse Lokset resin cartridge results in increased mixing efficiency and more uniform resin anchorage. Over two million units have been sold to date; the majority of these Eclipse bolts have been sold to coal mines in the Illinois Basin. Pull testing has demonstrated that a Grade 60 Eclipse bolt provides equal or superior pullout resistance as compared to a Grade 40 No. 6 rebar. Short encapsulation pull tests have yet to consistently demonstrate the superior pullout strength of Eclipse to standard B-Series, however 12 inch Eclipse grouted columns have successfully held in excess of the bolt yield load. The successful substitution of Eclipse bolts for A-Series has significantly reduced the primary roof support costs by approximately $0.18 per foot of bolt. Recent over coring analysis of various anti-gloving methodologies performed in New Zealand has confirmed the superior mixing of the Eclipse system (5).

Jan 1, 2004

By Marc T. Filigenzi

Two of the major ground control safety issues confronting underground mine operations today are shaft pillar stability and the failure of rock around active mine openings. Failure of a mine shaft can lead to the entrapment of workers. Failure of rock around active underground mine openings can lead to roof falls, which in turn can result in worker injuries and fatalities. Finite-element analysis has proven to he a reliable method for predicting stresses and displacements around underground mine openings. However, this is a complex and time consuming technique and is not used as often as it could be in mine planning. The purpose of this paper is to demonstrate one technique developed at the Spokane Research Center that allows the user to create a finite-element model of a two-dimensional section of an underground mine in a relatively straightforward manner. This model is then used to calculate stresses, displacements, and safety factors around mine openings. With this information, mine planners can evaluate the stability of mine openings as well as the stability of pillars and mine shafts. This analysis will help develop mining sequences and layouts that minimize stresses in that section of the mine. This, in turn, should minimize the occurrence of shaft failure, roof falls, and other hazards associated with underground mining.

Jan 1, 1997

By Y. P. Chugh

The paper discusses laboratory and field studies to analyze time-dependent deformation behavior of immediate weak floor strata in an Illinois coal mine. In the laboratory, core samples of the immediate floor strata were subjected to incremental creep tests under unconfined compressive stress. Both axial and lateral creep deformations were recorded. Time-dependent behavior was reasonably characterized by a Burger model with one Kelvin-Voigt unit. The elastic and viscous parameter8 of the model were found to be stress-dependent, but in the range of 40% to 80% of the failure stress, the effect of stress was relatively small. Therefore, a linear visco-elastic model was developed to represent the laboratory time-dependent behavior of immediate floor strata. Such a model may be acceptable for the design of partial extraction mining systems having extraction ratios of 40% to 60%. Field observations of roof-floor convergence (floor heave) at the mine also indicated a time-dependent behavior similar to that observed in the laboratory. Field time-dependent behavior was also characterized in terms of a Burger model with one Kelvin-Voigt unit to obtain scaling factors between the field and laboratory parameters. This approach should help in predicting likely floor heave in the mine based on laboratory creep tests. It was concluded that additional studies in the field are required to arrive at more reliable correlations between the two sets of parameters.

Jan 1, 1987

By Steven Derycke, Stephen C. Tadolini, Anand Bhagwat

"The tensile and shear strength of intrinsic bolting support systems has always been a major concern of designers. A comprehensive laboratory testing program was designed to evaluate the tensile and shear strength of individual wires and completely wound PC-strand cables. PC-strand cables with smooth wires and the recent anchorage enhancement innovation of indentation were evaluated and compared. The testing protocol detailed in ISO Standard 15630 utilizes a mandrel system that was investigated at 3 different diameters which alters the wire to mandrel ratio from 2:1 to 9:1. The results demonstrate that the difference between smooth and indented wires is statistically insignificant when larger diameter mandrels are used, and that indentation does not adversely affect strand properties and performance. Insight into the shearing mechanism and evaluation techniques are discussed with the introduction of triaxial loading to describe the PC-strand tensile and shearing mechanisms. Another important result indicates that the shear strength of PCstrand cable bolting systems has a greater shear strength value than traditional steel bar bolting systems.INTRODUCTIONPC-strand cable bolts have proven to be a global cost effective ground control solution in metal/non-metal and coal mines. The inherent strength to weight ratio of cable supports, combined with flexibility has been used in underground entries that range from 20 to less than 1.2 m in height (65 to 4 ft). In coal mining, the systems are used as primary and secondary support installed both passively or actively with installation tensions that range from 38 to over 178 kN (8,500 to 40,000 lbs) . While cable can be specified in several diameters, the most predominant sizes in the US remain 15.2mm (0.6 in) and 18mm (0.7 in). The capacity of the systems defined in the ASTM 432-13 is 90% of the minimum strand strengths of 260 kN (58,600 lbs) and 320 kN (72,000 lbs), respectively.Cables are not only suitable to support vertical loads, but are also often used to effectively support fractured and jointed materials and can be exposed to shear forces across the wound PC-strand structure. In fact, Goris et al. reported that cable bolts placed across jointed surfaces could more than double the shear resistance. These results were duplicated for both smooth and rough jointed surfaces (Goris et al., 1996). An example of tensioned cable bolts used to support a fractured and sliding roof in a longwall tailgate entry is shown in Figure 1."

Jan 1, 2015

By Quanzhong Gu

Stability of a pre-exnacted recovery room plays a vital role when longwall face approaches and during a longwall face move. In an attempt to extend the application of pumpable cribs into recovery room support and to limit roof bolt installation when a longwall face approaches the recovery room, yieldable and cuttable pumpable cribs (YCPC) were employed in the recovery room at the northern West Virginia mine. The YCPC consists of two layers of materials with different strengths. This allows considerable deformation from the floor and/or roof by sacrificing the soft layer while maintaining relatively high load capacity under mining¬induced front abutment loads. The thickness and stiffness of the soft layer, installation and quality control are the key factors when using the Yieldable and Cuttable Pumpable Crib to stabilize longwall recovery room- Underground observation and monitoring results show that the Yieldable and Cuttable Pumpable Crib is a viable solution to insure stability of the recovery room and can save at least two days for a longwall face move at the mine.

Jan 1, 2004

By Thomas L. Hutchinson

The mechanical design of a roof support is basically a matter of a statics and dynamics problem, assuming of course, that the imposed loads and mining conditions are known. Here in the Appalachian coal fields the general conditions are known well enough to allow the majority of the proposed new faces of longwall to be furnished with standard commercially available supports equipped with suitable variants and options. While not trying to negate the primary importance of thoroughly investigating a potential face and the selection of the correct equipment for that face, it still becomes clear that an equally important aspect of the design of an adequate ground control program has in the past too of ten been overlooked, having been overshadowed by the ?endless? selection process of the roof supports proper. The equally important aspect which this paper discusses is the overall design of a mining system, which design incorporates not only the size and capacity of the equipment but the following points as well, namely: Equipment adaptability to mining scheme, Equipment va. human constraints, Operation at the designed levels, and Coordination of operation, maintenance and support design. Unless the coordination of these factors is considered in the design and selection of the equipment, a lopsided and inefficient operation is possible. How can we afford to put an 8-10 million dollar investment up to chance as to whether it will yield optimum results or not?

Jan 1, 1981

By David Bigby

The paper describes research undertaken on an ECSC/K HSE project which investigated several potential physical principles which might be harnessed to provide a non-intrusive means of determining the extent of failure in the near roof of mine roadways and tested the most promising in the laboratory and in the field. It was concluded that the principles which warranted further development were thermal response and laser vibration measurement. In the latter case there is a need to develop an efficient means of imparting energy to the seam to induce sufficient vibration. A new, SIMRAC funded Project will progress work in the field of thermal response.

Jan 1, 2004

By E. Bane Kroeger

For many years, researchers around the world have been investigating coal pillar stability. Many have focused on trying to optimize the size of the pillars by examining stable and failed pillars in underground coal mines. For mines that are already in operation or companies that are opening a new mine adjacent to an existing mine where the pillar dimensions and stability can easily be determined, this is the preferred technique. However, when a new mine is planned for an area where there has been relatively little mining, then samples of the coal need to be drilled and tested for strength. Because of the fractured nature of coal, this lab testing is often problematic and may often yield poor results because of the limited size and number of samples that can be obtained from the core. To remedy this problem, research was conducted in the labs at SIUC to determine if improvements could be made when optimizing the size of pillars for underground coal mining in Illinois. Through a greater understanding of the relationship between dimensions and strengths of coal samples tested in the lab, it was hoped the in situ strength of coal pillars could be determined with greater accuracy. This could allow the extraction ratio to be increased and more of the coal resources in Illinois recovered without impacting the safety of the mine workers. Many different agencies around the world have published recommended minimum numbers of samples for strength determination based on the size of the coal samples. For two inch cubes, uniaxial testing of at least seven samples is recommended and this minimum number decreases to four when testing four inch cubes. However, the laboratory testing of coal from two seams thus far has suggested this number should be almost doubled to accurately determine the coal strength. Testing also showed there is a pronounced decrease in the variation in the strength of the samples tested as the dimensions of the sample were increased. From the testing results thus far, it is recommended that a sample size versus strength curve be constructed for every coal seam for Illinois. Creating such a curve will better determine both the minimum number of samples and minimum sample dimensions for that seam or region of a particular scam. A second set of tests were conducted in the laboratory to determine the increase in strength with reduction in height for samples with the same width and length. In Illinois, typical pillar dimensions are 40 to 80 feet (12.2 to 24.4 m) wide and long, with coal thickness varying from about 4 to 9 feet (1.22 to 2.74 m). This provides width/height ratios ranging from 4.5 to 17.5. Coal samples having width/height ratios ranging from 0.5 to 13 have been tested thus far. As with most pillar design formulae, the strength of the Murphysboro coal versus width/height ratio was linear and closely matched shape factors published by other researchers. The laboratory testing thus far has identified three factors that affect the strength of laboratory samples, the number of discontinuities, the angles of critical discontinuities, and the shape of the samples. The factor that probably had the most pronounced effect on the strength of the coal samples was the angle of critical discontinuities. This testing has confirmed that there is still a gap that needs to be bridged between the strength obtained from laboratory testing and the in situ coal strength predicted.

Jan 1, 2004

By Douglas Morrison

By applying modern 3D numerical modelling techniques to the analysis of a pillar cascade failure in a room and pillar mine, it has been possible to simulate the collapse and develop an understanding of the role of low rock strength areas within the mine. The cascade collapse occurred in a normal strength area but would not have occurred without the influence of a low strength rockmass in one section of the mine. The numerical analysis made it possible to develop a realistic assessment of the residual pillar strength. With the introduction of regular empirical pillar performance assessments, critical pillars or groups of pillars can now be identified proactively. This has led to an aggressive extraction ratio of 90% that manages pillar failure, avoids pillar and roof collapse and prevents surface subsidence. Since the mine also has significant waste products, the use of backfill for ground support has made it possible to significantly improve the performance of strategically located pillars, and so achieve even higher extraction ratios.

Jan 1, 2003

By Erdal Unal

In gate roads where supports are subjected to dynamic loading four times due to retreating longwall panels, it is a real challenge to replace the rigid arches with flexible reinforcement systems and yet to provide safety and stability of these openings within better economical limits. The results presented in this paper are based on a three years of research project aimed at developing safe and economical support systems for gate roads in Çayìrhan coal mine. Çayìrhan -Mine Project includes laboratory and field studies, design analysis, pilot scale design applications and performance monitoring. Based on outputs of the design approach developed, four types of bolts, namely, Split Set, Yielding Super Swellex, Sis-Resin, and Fosroc-Resin bolts were installed in a gate road together with widely spaced yielding steel-arches. In order to compare the performance of these flexible support systems and to provide feed back for the design approach, a monitoring program was initiated.

Jan 1, 1993

By John L. Hill

Over 50 mines of the Appalachian and Illinois Basins are presently experiencing poor ground conditions believed to be caused by overlying stream valleys. The Bureau of Mines is conducting research into the causes of this problem with the aim of developing a predictive method for determining the safe limits of mining beneath stream valleys. In addition, the factors that control instability in these regions will be analyzed to provide design guidelines for adjusting support requirements. This paper presents the theorized causes of poor ground conditions beneath stream valleys and compares the theories with the results of a Bureau study of the Birchfield Mine No. 1 and a preliminary investigation of the Davidson Mine, both of southern West Virginia. The Birchfield Mine excavated four main entries beneath a 50-ft wide stream with only 50 ft of overburden. The valley flood plain is over 500 ft wide, flanked by valley wall slopes of 25 deg and relief of over 950 ft. In-mine monitoring of strata movement and detailed geologic mapping revealed that roof rock strength was greatest under high cover and weakest along outcrops and beneath the valley, with localized areas of decreases in rock mass quality. To improve the rock mass quality beneath the stream and reduce the threat of inundation, an extensive drilling program was undertaken to inject grout into the overburden from the surface. As a result, mining beneath the stream was practically routine from a ground control perspective, and water was not encountered until mining had advanced to a point beneath the floodplain that had not been grouted. The only ground control problems which were encountered were entirely a result of localized poor rock mass quality. In contrast to the Birchfield Mine, the Davidson Mine experienced failure of intact roof rock at a depth of 300 ft beneath a V-notch shaped valley with no change in rock mass quality. Finite element analysis was conducted to study the premining in situ stress at the two sites. The results are discussed within this paper and provide insight into the causes for the types of failure seen beneath valleys of varying shapes and depths.

Jan 1, 1988

By Daniel W. H. Su

Surface subsidence induced by multiple-panel coal extraction was calculated with finite element stress analysis. The use of nonlinear material behavior and GAP elements, which provide a realistic representation of shearing along existing planes of weakness, allows the finite element program to accurately reproduce observed subsidence profiles. A reduction factor of 1/6 is applied to the measured rock strength and modulus for use in the finite element model. The models satisfactorily predict a significant change in maximum subsidence and subsidence profile associated with an increase from subcritical to near critical panel width. Modeled shearing along planes of weakness is in good agreement with available time domain reflectometry field observations and is demon¬strated to have a very profound effect on the maximum subsidence and the shape of the subsidence profile. When both material nonlinearity and planes of weakness are incorporated, the finite element model appears to possess great potential for accurately predicting surface subsidence and subsurface strata deformation in environments where little subsidence information is available.

Jan 1, 1990

By Paul Hagan

A diverse range of rockbolt designs and resin anchors are available for use in underground mines. Despite their wide spread use, the factors that affect the performance a rockbolt is not fully understood. The laboratory-scale rockbolt test facility at the UNSW Mining Research Centre is being used to gain a better understanding of the behaviour of rockbolts leading to an improvement in ground support. A test program investigated the nature of load transfer between a fully encapsulated rockbolt and the surrounding rock mass. It was found that with all other factors held constant, there were differences in the behaviour of load transfer depending on the method of loading. The typical pull-out arrangement as used in most field test work resulted in a different load transfer function to that observed when the load on the rockbolt was induced through bed separation.

Jan 1, 2004

By H. Gene Wilson

Mobile Roof Supports (MRS) look similar to a longwall shield on crawler tracks. The MRS units offer a safe, productive method of extracting the 40% to 60% product left normally unrecovered in room and pillar mining. The units feature radio control, self-contained power units, crawler track drive, and a 600 ton yield. Cribbing and setting posts in retreat mining has been a necessary burden to production. The MRS reduces this burden. Long blocks of coal can be developed to further reduce move and tram time, thus increasing production. The MRS units have successful safety records. The workers are removed from the immediate fall area, and we feel back injuries have been reduced by the workers not setting posts. While MRS units have been damaged in falls, the other capital equipment has been unharmed. The MRS product line has undergone normal product improvement and evolution. Product evolution is seen in our development of machines for particular mine requirements. Through the continuing development of the MRS, Fletcher presents the coal industry with a safe, productive method of retreat mining with potential to develop new mining methods.

Jan 1, 1990

By Herryal Anwar

The application of roof bolting technology to control the stability of roadways in coal mining within weak strata or under high ground pressure has improved progressively. One of several factors that affect the design of rock bolting is the immediate roof characteristics of the roadway. On the competent rocks, the mining conditions may indicate a high level of stability and a low density of bolting patterns may be adequate to control the ground stability. However, at a weak strata, the roadway will be affected by both horizontal and vertical stresses that may generate a high level of deformation in the immediate roof. This sensitivity of the roadway will require a mine plan design which consider the pillar sizes and sequences of extraction as well as a conservative reinforcement to maintain the integrity of the deforming weak roof strata. Rock bolting technology has been used to maintain the stability of roadways in Indonesia and Japan for a few years. In this paper the overview of the application of rock bolting reinforcement in Ombilin Coal Mine, Indonesia and Miike Coal Mine, Japan is given.

Jan 1, 1999

By David I. Hoyer

It is shown that by monitoring longwall leg pressures in real time, warning can be given for significant weighting events and the formation of roof instabilities, such as roof cavities, several hours in advance. Longwall Visual Analysis (LVA) is a software package that continuously monitors shield pressures and shearer position in longwall mines. LVA has been running on 19 Australian longwalls for up to four years, and as a result a very substantial database of shield pressure trends in a wide range of longwall situations has been collected. This database has been analyzed to develop indicators that will give operators and geotechnical engineers advance warnings of developing conditions such as weighting events and difficult roof conditions. LVA displays live charts of data, such as shield leg pressures, loading rates, and yield frequencies. Data analysis techniques were applied to historical data records from multiple longwall sites in order to develop a ?Cavity Risk Index? (CRI). The CRI indicates the risk of roof cavities developing, and it is based on pressure trends that indicate significant yielding and loading rates spanning a region of relatively low support. Case studies from different longwalls are given, showing how the CRI can give real-time advance warning of the formation of roof cavities with their anticipated location on the face. The limited number of case studies done so far indicate that the predictions have a high degree of reliability, but more work is required to quantify this.

Jan 1, 2011

By Wm. Mark Hart

Under a specific geological condition, roof supporting method, and pillar-entry system, an entry convergence concept may be the most effective means that can be used to effectively indicate the longwall entry stability (i.e. pillar bumps, roof falls, or floor beaver This concept may also be used to verify the effectiveness of the current pillar-entry system and roof supporting method. Furthermore, convergence measured under different mining phases may lead to a better understanding of the longwall mining-induced abutment loads and may be used to estimate stress change in pillars and thus pillar stability. In this paper, a remote entry activity monitoring system was designed; a comprehensive entry convergence monitoring strategy was proposed; thee abutment loading phases in longwall mining were defined; the relationship between roof deflection and stress change in a pillar was derived, and finally the extent and magnitude of the mining-induced abutment loads as well as their impact on entry convergence were discussed using the field data obtained so far.

Jan 1, 1995