Search Documents

By G. Deschenes, P. J. H. Prud'homme

A laboratory study was carried out to evaluate the effect of oxygen and lead nitrate on the recovery of gold by cyanidation of a free milling gold ore, which contains 0.4 % copper as chalcopyrite. Efficient gold extraction is achieved only under specific conditions. The recovery of gold was increased from less than 90% to up to 98% by addition of lead nitrate. In the pre-leaching, the kinetics of oxidation of soluble sulphides are not an accurate indication for the length of the treatment. Even though the consumption of cyanide was reduced due to the inhibition of the dissolution of chalcopyrite by increasing additions of lead nitrate, cyanide consumption had to the held above 1.85 kg/t to maintain good recovery of gold. The continued addition of lead nitrate above 300 git had no impact on the recovery of gold. It was also found that the addition of lead nitrate at the start of cyanidation gave the same performance as when added during pre-leaching. The addition of oxygen increased the recovery of gold by 1.5%. The concentration ofNaCN had to be maintained in the range of700 mg/L because of the high concentration of copper in solution. The recovery of gold dropped significantly when the average NaCN concentration fell below 640 mg/L. Application of the findings of the laboratory study at the industrial scale led to improved plant performance.

Jan 1, 1997

By Q. Yuan, B. Yarar

Steric stabilization is a phenomenon observed when relatively high doses of flocculants are added to fine particle suspensions. Experiments were conducted to establish conditions under which medium viscosity and the sedimentation properties of black sand components in a slurry could be controlled so as to enhance the selective sedimentation of gold grains. It was shown that black sand concentrates containing as low as 2.65 g/mt gold could be upgraded by selectively hindering the sedimentation of non-gold components in an aqueous slurry. This paper presents data describing the theory and practical implementation of this cyanide or mercury-free novel approach where gold could be concentrated by as much as 15 times with relatively high recoveries. The relationships of solids content of slurries, type and dose of polymers with the recovery process are documented. Key words: Gold, black sand, selective flocculation, steric stabilization.

Jan 1, 1993

By Tadashi Nishida

Subsidence due to mining caused various kinds of damage to the surface structures, and actually great deal of mining damage becomes the severe social problem at some time in many coal fields, but the most of mining damage was restored at present. Recently, the effect of old coal working on the deformation of newly constructed structures has become into question, because it was obliged to plan many engineering structures in old mining areas for the shortage of adequate construction sites and the difficulty of getting location. That is, building, dams, bridges for railroads and highway, power plants, tunnels, storage tanks and so, have to be built on the ground which has old coal working.

Jan 1, 1982

By S. K. Das Gupta

The rock laterite was first discovered and described in the State of Kerala, India in 1800 A.D. by Francis Buchanan. It had been used here, and elsewhere in India, for many centuries as a building stone, but in Buchanan's time it was not known that some of these laterites were highly aluminous and could be processed to produce alumina. After World War I India started searching for bauxite reserves with a minimum grade of at least 50% A12O3. By 1960, it was estimated that India had a potential reserve of 245 million tonnes of bauxite, about 10% of which was in the "Proved" category. Subsequent geological exploration now reveals that India has an overall resource of more than 2 billion tonnes of aluminium ore, not all of it bauxite, as defined by earlier geologists. In this paper, the geology, resources and distribution of bauxite and aluminium ore throughout India are described. The generalised stratigraphy, typical laterite and bauxite profiles and summary of the resource position are shown in the attached Tables 1 to 8. It is generally agreed that a tropical to sub-tropical climate, intermittent wet and dry season, good permeability of country rock and suitable drainage, as well as physiographic and ground water conditions are important in the development of bauxite.

Jan 1, 1984

By Leszek W. Lunarzewski, Adam L. Lunarzewski, Raymond C. Pilcher

The Floorgas and Roofgas simulation programs are used to identify strata relaxation zones and their boundaries, to assess active gas sources from coal seams and gas¬bearing rocks and to determine relevant gassiness prediction coefficients for any local longwall. The paper shows that by use of the print-outs from the Floorgas and Roofgas programs the following benefits are achievable: • identification of the shear and gas discharge zone positions in the floor, strata relaxation angles and various gas discharge zone positions in the roof, which are both relevant to local geological and mining conditions • optimisation of cross-measure drainage hole length, location, number and angle of inclination calculation and definition of gas make prediction coefficients such as the release ratio from adjacent coal seams, specific gas emission during longwall extraction and the relationships between gas make, longwall width and coal production levels.

Jan 1, 1995

By A. H. Shapiro, W. –F. Leung

A decanter centrifuge of novel design was developed for the dewatering of fine-solids slurries having micrometer-range particles that form pastelike, flowable, hard-to-dewater cakes. The design combines a compound beach with a cake flow control structure that allows expressed liquid, from the cake in the dry beach region to be returned to the liquid pool while maintaining a high-solids throughput. To provide optimal performance with various operating parameters (i.e., feed rate, centrifugal gravity, pool, differential speed, concentration of feed solids and slurry type), the cake flow control is adjustable. The second part of the beach is preferably at a zero angle. Tests showed that the new design allows increases in solids dryness and solids throughput. Key words: Dewatering, Centrifuge, Slurry, Fine particles, Beach decanter, Cake-flow control

Jan 1, 2003

By E. Asselin

Passivation of Fe-Ni-Co alloys during the Caron leach process is thought to result in low cobalt recoveries in ammoniacal ammonium carbonate solutions. A brief review of the available thermochemical data for the (Fe, Ni, Co)-NH3-H2O systems has been undertaken. The stability of the Co(II) and Co(III), Ni(II) and Fe(II) ammines was examined through the use of speciation and Pourbaix diagrams at 298 and 333 K and at 6 M total ammonia. Increasing the temperature reduces the stability fields of the ammines and generally constrains the thermodynamic window for the leach. The Fe(II) ammines are only thermodynamically stable under reducing conditions. Polarization experiments show that these ammines are unlikely to form if oxygen is present. Fe-Ni-Co alloy passivation may be alleviated by careful management of potential.

Nov 1, 2011

By Aurel Goodwin, Diann Kraft, V. S. Znamensky

This chapter deals with the Mine Safety and Health Administrations's (MSHA] concern and obligations with regard to asbestiform minerals. Asbestiform minerals are defined as the magical group of hydrated, silicate minerals that possess a fiberlike structure capable of being woven into cloth. Their unique combination of properties, such as resistance to heat and chemical attack, high tensile strength, and flexibility was recognized centuries before Christ. Pausanias, the early Greek geographer, speaks of golden lamps, made about 430 BC, with in- combustible wicks of Carpathian flax. The Ro- mans used asbestos as cremation clothes to con- serve the ashes of deceased persons of rank. Charlemagne had an asbestos table cloth that he used to pass through fire to clean (Lanza, 19381. Early recognition of the health hazards associated with exposure to asbestos was documented in the first century by Pliny the Elder, a Roman naturalist, and Strabo, a Greek geographer. Both wrote of slaves with sickness of the lungs, whose occupation was that of weaving asbestos into cloth. This concern for the health of asbestos workers disappeared over the ages. Today, with the use of modern technology, asbestos products have been greatly exploited. The asbestos output has increased over a hundredfold in the past 70 years. World production has jumped from 454 t/y (500 stpy) in 1900 to 4.5 Mt/y (5 million stpy) in 1978. An increase in health problems for asbestos workers accompanied this increased usage. However, it was not until the modern era that the association of asbestos with chronic respiratory disease was rediscovered. Reports were published at the turn of the century documenting the effects of asbestos exposure on textile workers. One such report in 1907 by H.M. Montague Murray described the post mortem findings on a 34-year- old carding machine operator. Murray de- scribed the lungs as showing extensive diffuse pulmonary fibrosis spicules of asbestos. Subsequently, more reports of pulmonary fibrosis following inhalation of asbestos were published, including an epidemiological study of asbestos miners in 1930 (Merewether and Price, 1930), at Thetford, Que., Canada. This study took place at the mine 52 years after large-scale mining of asbestos had begun. But, the cancer- producing potential of asbestos was not established until 1949 when a report by Merewether in England described an excess of cancer of the lung and pleura [the lining of the lungs) among individuals dying from asbestosis (Merewether, 1949). In the past decade much attention has been focused on asbestosis, mesothelioma, and bronchogenic carcinoma, as the three major biological effects associated with asbestos ex- posure. Parenchymal and pleural asbestosis is a fibrosis in the substance of the lung with thickening and often calcification of the membranes lining the thoracic cavity. Mesothelioma is a malignant tumor of the membranes lining the thoracic or abdominal cavities, and bronchogenic carcinoma is a cancer of the lung tissue itself. These diseases occur in various degrees and combinations. The severity and occurrence of these biological effects are directly influenced by conditions such as dose response relationships, intensity of exposure, duration of exposure, lapse of time since initial exposure, and cigarette smoking. Numerous studies indicate that the relationship between these conditions and the incidence of disease is proportional. Congress has recently concluded (Congressional Record, 1979) that, "exposure to asbestos fibers has been identified as significantly in- creasing the incidence of cancer and other severe or fatal diseases such as abestosis." Congress conveys its concerns for the safety and health of the nation's miners through the Federal Mine Safety and Health Act of 1977 in which it gave MSHA the authority to set safe

Jan 1, 1986

By Charles K. Presley

This paper deals with drilling large diameter shafts for the mining and construction industry with diameters in excess of 3 feet to more than 20 feet in diameter. It discusses appropriate applications of the rotary drill method, linings for large diameter shafts, circulation systems,, and the limitations of the method. Each specific rotary drill method is determined by the geology of the area, the depth to be drilled and the formation fluids encountered. Shaft lining or casing must be improved to result in lighter weight, higher strength and lower cost. All phases of rotary drilling equipment must be improved to drill shafts in excess of 10 feet in diameter. As these goals are reached, more shafts of large diameter will be drilled by the rotary method for the mining and construction industry.

Jan 1, 1967

By J. Le Gac, P. Zettwoog, J. Brenot, J. W. Piechowski, J. C. Nenot

INTRODUCTION The components of the radiological hazard in uranium mines are: 1. exposure to radon and its short-lived daughters 2. exposure to long-lived ore dust 3. external irradiation With usual ventilation rates, the dosimetry relative to the first component only requires to know each miner&apos;s exposure to a potential energy of short-lived radon daughters, (EXP[a]). Presently in France, (EXP [a]) is determined monthly from radon concentration measurements. This is an indirect method based on ambient monitoring. After technical improvements achieved during the last years it is now possible to measure (EXP [a] directly with an individual portable monitor developed by the CEA. The purpose of this study is to analyze and compare monitoring results obtained by these methods. DETERMINATION OF INDIVIDUAL MONTHLY EXPOSURES TO[ a] POTENTIAL ENERGY OF SHORT-LIVED RADON DAUGHTERS [(EXP a) amb, by ambient monitoring] In this case, it is necessary to know individual monthly exposures to radon, (EXP Rn). As mentioned by Pradel, J.,et al., 1976, (EXP Rn) is estimated for each worker from informations both on radon concentrations (CRn) measured as described by Pradel, J., 1962 and times (t) elapsed in the various workplaces. (EXP Rn) is obtained by summing up the elementary radon exposures CRn x t relative to all the workplaces where the miner was successively engaged during the month. (EXP Rn) values are then corrected by an average equilibrium factor of 0.17 deduced from many measurements and taken as representative for all the French mines. Finally: [ ] (EXP [a])ind are obtained directly with an individual portable instrument described by Chapuis, A.M., et al., 1972. Samples of the air breathed by the miners are pumped continuously and radioactive aerosols containing the short-lived radon daughters are trapped on a filter. The principle of the measurement lies on track-etch detection of the a particles emitted by the deposited material. The technical aspects have been described by Duport, P., et al., 1980a, Mouden, A., et al., 1980 and Chapuis, A.M., 1980. As mentioned by Duport, P., et al., 1980, fiability is good. Indications on measurement reproducibility are given by Pradel, J., et al., 1977. PRESENTATION OF THE STUDY The underground miner population of a French mine was followed during a period of 8 months (October 1978 - May 1979). Monthly exposure values for each miner determined either by ambient or individual monitoring, (EXP [a])amb or (EXP[ a])ind, had been previously collected by Le Gac, J., 1980, who had also defined miner categories according to the characteristics of the work performed. Four groups are considered here, the "whole mine" and three categories as described in table 1. Data on the individual monthly exposures,(EXP [a])ind and (EXP [a])amb, were taken again to analyze the individual cumulative exposures instead of the "month by month" values. The influence of the mean habits of each individual on its surveillance results is thus taken into account. Each miner has a cumulative exposure as an individual of the "whole mine" and as an individual of each category in which he has worked. The results obtained by ambient or individual monitoring were analyzed (characteristics and adjustements of the distributions) and then compared (description of the discrepancies observed). Obviously, such a study is possible only if all the exposures are cumulated on a same duration. As miners have not worked during the same number of months in the course of the data collecting period, one must considerer the individual average monthly exposures, [(EXP a)]amb and[ (EXP a)]ind, instead of the individual cumulative exposures, which is typically the same thing. To be sure that the exposure values of a given group (A, B, C or D) are representative, only those miners really present for at least 3 months in this group were taken into account. Finally, each individual of the "whole mine" and of the various work categories has a pair of average monthly exposure values : [(EXP a)amb] determined by ambient monitoring and[ (EXP a)ind] deduced from the track-etch recording of the individual portable monitor. Let a miner be engaged during n months[ (3 < n < 8)] in a group, the following relations then apply : [ ]

Jan 1, 1981

By M. D. McInnis

The Jualin Gold Prospect is centered on Johnson Creek, approximately 40 air miles north-west of Juneau, Alaska. The property is on the southern end of the Kakuhan Range with Berners Bay immediately to the south and Lynn Canal to the west. The property is accessible directly by helicopter from Juneau or by float plane to the head of a 5.5 mile gravel road that begins on the north side of Berners Bay and terminates at the old workings of the Jualin Mine near the center of the property.

Jan 1, 1989

In a future world of 8.5 billion people in 2035, the Energy Information Administration&apos;s (EIA) projected 50% increase in energy consumption will require true "all of the above" energy resource use from oil, gas, renewables, nuclear, and coal. In particular, coal will continue to be the world&apos;s energy cornerstone, providing more incremental energy over that same time period than any other single fuel. Coal has long been a centerpiece of a low-cost, high-reliability electricity grid. Today there are 1.3 billion people across the globe without access to electricity and 2.7 billion people who do not have clean cooking facilities. The problem is spread across the developing world, but it is particularly severe in sub-Saharan Africa and developing Asia, which together account for 95% of people in energy poverty. Without a commitment to achieve universal energy access it has been estimated that by 2030, there will be an additional 1.5 million premature deaths per year caused by household pollution from burning wood and dung and through a lack of access to clean water, basic sanitation and healthcare. Modern energy sources are essential to meeting these challenges.

Jan 1, 2012

Sequential and evolutionary changes through time are recognizable in many, perhaps most major families of ore deposits and their geological environments. These changes are additional useful indicators of the evolutionary history of the earth and its tectonic processes. They are important in mineral exploration because they involve consideration of time as a fourth dimension, thereby indicating the most favorable ages, rather than types of rock for investigation. Many of the changes are analogous to those recognized in faunal evolution. Some primitive, unspecialized types of ore deposits occur nearly unchanged through rocks of widely differing age. Others diversify into several, more specialized variants, whereas still others become extinct. The place of these is taken by new, younger types, some of which undergo sudden proliferations and later diversifications of their own. In Archean greenstone belts irrlportant iron, nickel, gold, and base metal deposits occur co-regionally, but in different stratigraphic positions in the same, thick volcano-sedimentary successions. Here their close temporal and spatial associations suggest common genetic exhalative hydrothermal processes. The massive base metal sulfide family of ore deposits provides an excellent example of evolutionary changes, exhibiting distinct variations through both time and space. Deposits belonging to this family span the entire range of time, occurring in rocks of ancient Archean to Recent age, and specific types within the family also span the entire range of spatial environments from ensimatic to ensialic. Moreover there are possible evolutionary metallogenic links between certain types of massive base metal sulfide deposits and other important base metal ores, noteably Mississippi Valley-type and porphyry copper deposits.

Jan 1, 2013

By J. D. Miller

X-ray computed tomography (CT) techniques have been developed for the medical services field in order to provide accurate internal images of the human body.(l-7) Now, a decade later, CT techniques are starting to be used in non-medical applications such as, non-destructive testing(8), flow pattern analysis(9), drill core examination (10,11), and coal characterization(12,13). In these fields of application, CT techniques offer the potential to extend our knowledge and understanding beyond that provided by more traditional methods of analysis. Although, CT systems involve very specialized and expensive equipment, the advantage of x-ray CT in revealing the detailed internal structure of an opaque material non-destructively should make it an important tool to provide a more complete analysis of mineral processing phenomena. X-ray CT systems generally consist of an x-ray source/collimation unit and a detector/data acquisition unit. The object to be examined is placed between the two functional units as shown in Figure 1. With this system the density array of selected cross sections of a chosen opaque object can be obtained in two dimensions. There are numerous areas in mineral processing to which x-ray CT technology can be applied and it is the aim of this article to identify these potential areas noting the advantages and limitations of the technology. Particular emphasis is placed on particle composition distribution and multiphase fluid flow measurements. In the case of particle composition distribution, liberation analysis and coal washability are considered. While in the case of multiphase fluid flow, swirl flow in the air-sparged hydrocyclone is given by way of example.

Jan 1, 1989

By N. T. Rempe

The underground voids that result from mining provide opportunities for deep geologic waste disposal (DGWD). Such disposal could solve many environmental problems. DGWD takes careful planning, technology transfer and true partnership between waste generators and mine/repository operators. The US government is now planning on using specially mined excavations to dispose of radiotoxic and mixed waste. Using the experience gained from the domestic projects that are now in preparation and from foreign repositories that are now in operation, US mines can claim their rightful share of the growing market for DGWD.

Jan 1, 1997

By N. Damiano, C. Zhou, R. Jacksha, J. Srednicki

Modern electronic devices and systems used to enhance miner safety and health are becoming commonplace in underground coal mines. The ability for these devices and systems to function properly in the presence of electromagnetic emissions from other electronic and electrical devices and systems is not entirely understood. To investigate potential electromagnetic compatibility issues of critical mine electronic devices and systems, researchers from the National Institute for Occupational Safety and Health (NIOSH) are conducting surveys of electromagnetic emissions in underground coal mines. This paper presents the measurement system, methods, and results of electric field electromagnetic emission surveys conducted in three underground coal mine environments in the frequency range of 10 kHz to 1000 MHz. The survey data show that in some environments electric field electromagnetic emissions in underground coal mines approached or slightly exceeded limits as defined by other industrial sectors.

Mar 2, 2022

By S. K. Kawatra, H. J. Haselhuhn

"Fine-grained hematite ore can be concentrated by the process of selective flocculation and dispersion, which relies on proper reagent selection and control of water chemistry. While many previous studies have been performed analyzing the effects of different reagents on this process in a laboratory environment, this paper focuses on investigating the water chemistry within the process in a pilot-scale continuous deslime thickener.The pH, sodium concentration, calcium concentration and magnesium concentration were varied to determine their effects on the iron concentrate grade and recovery, and the phosphorus concentrate grade and rejection in the pilotscale selective deslime thickener. The ideal pH for the iron grade and recovery of the process using a starch selective flocculant was found to be 10.5. Phosphorus rejection, however, was increased at lower pH values. Minimization of sodium concentration was shown to improve iron grade, iron recovery and phosphorus rejection. Calcium acted as a nonselective flocculant showing higher iron recovery, lower iron grade and lower phosphorus rejection with increasing concentration. Conclusions could not be drawn from the experiments that varied magnesium concentration.The zeta potential of the solid-liquid interface of particles in each sample taken was also analyzed to show relationships between zeta potential and process performance. In all cases, a maximization of the magnitude of zeta potential correlated with increased iron grade and recovery. This supports the hypothesis that a higher level of dispersion enhances the selective flocculation and separation process.IntroductionThe United States produced 53.2 million metric tons out of the 3,000 million metric tons of concentrated iron ore produced worldwide in 2012 (Tuck, 2013). With this in mind, there has been a large increase in iron ore processing research (Bolen, 2014; Carlson and Kawatra, 2008, 2013; Halt and Kawatra, 2014; Halt et al., 2014; Haselhuhn et al., 2012a,b, 2013a,b; Liu et al., 2014; Manouchehri, 2014; Sandvik and Larsen, 2014; Semberg et al., 2014). Of the 53.2 million metric tons produced, roughly 8 million metric tons of hematite (Fe2O3) concentrate were produced using a process known as selective flocculation and dispersion (Cliffs Natural Resources, 2011). This process is the only economically viable method for concentrating low grade (< 40% Fe) fine grain (< 25µm liberation size) hematite ores. It is scarcely used due to difficulty in controlling the surface chemistry of the ore and high reagent costs (Department of Energy, 2001; Haselhuhn et al., 2013a). The process is highly dependent upon both reagent selection and precise control of the water chemistry during separation. This study shows the dependence of the process performance of a pilot-scale deslime thickener on the water chemistry in the feed slurry."

Jan 1, 2015

By C. J. Johnson

As the U.S. coal industry moves into the next century, it is becoming more apparent that the effective application of new technology is the only way it can remain competitive in the energy marketplace. Examples of this emphasis are with us today in such diverse areas as face-ventilation and excavation-equipment applications. The focus of this new technology is directed toward improvements in health and safety, cost control, and productivity. Room-and-pillar mining accounts for approximately 80% of the nation&apos;s underground coal production; this percentage is not expected to decrease markedly in the near future. As such, this paper analyzes the impacts of the changing technological climate on future room-and-pillar operations by comparing a base-case section (current) to three scenarios incorporating new or emerging technology. A microcomputer-based comparative analysis will reflect the changes in section production and costs.

Jan 1, 1988

By D. Farnell

Large semi-autogenous (SAG) or autogenous grinding mills have become the work-horse of the modern high volume concentrator. They typify the economy of scale - fewer, larger machines doing more work, more economically. With fewer machines, equipment reliability becomes of paramount importance. Realizing this, companies installing new or modernizing existing facilities have placed extraordinary emphasis on purchasing a reliable mill. This, in turn, has had a significant impact on mill design. Kennecott And Codelco - Two Different Approaches Last year, two of the world&apos;s largest copper producers, Codelco and Kennecott, undertook the modernization of their main grinding facilities at Chuquicamata and the Utah Copper Division (UCD) respectively. Both selected semi-autogenous milling and both, recognized the importance of the reliability of the primary mills. Each, however, decided on a different approach to optimizing reliability. Codelco placed the emphasis on technical innovation in design and opted for a gearless driven mill. Kennecott chose the more conservative approach of active participation and exceptional quality assurance in mill design and manufacture.

Jan 1, 1987

By A. Bruynesteyn

Procedures are discussed to determine if a waste material can become acid producing when left exposed to the environment. When wastes proves to be acid producing, methods are described that can be used to determine the characteristics of the effluents produced from a commercial size waste dump, taking into consideration that large quantities of pollutants can accumulate inside a waste dump during dry periods. The length of such dry periods and the quantity of rainfall greatly affect effluent characteristics.

Jan 1, 1980