Search Documents

By B. Stewart

Recent ore pass failures have underlined the need for improved designs, standards, structural monitoring methods, and better hang up prevention and removal techniques. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) are investigating methods to improve safety during transport of ore in ore passes. Design criteria and hang-up prevention and remediation strategies involve studies of the effects of static and dynamic ore and waste rock loads on chutes, walls, gates, and support structures. Particle flow analysis methods were used to simulate the response of various ore pass designs to a wide range of ore loading conditions. A full-scale mock-up of actual ore pass and chute assemblies was duplicated and tested for load response. Data from a particle flow code and the mock-ups were com-pared. Loads on an active ore pass chute were measured.

Jan 1, 1998

By K. V. Raj, R. Jacksha

Conveyor systems persist in being a source of injuries and fatalities in the mining industry. To reduce these incidents, better methods are needed to enhance the monitoring of probable hazards and improve situational awareness during the normal operation and maintenance of conveyor systems. To address these issues, researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) continue to investigate emerging technologies that show the potential to improve miner safety around conveyors. This paper presents a feasibility assessment by NIOSH researchers of a fully integrated, commercially available wireless Internet of Things (IoT) system to improve situational awareness around conveyor systems.

By R. T. Swindeman

"INTRODUCTION This paper will discuss the topics in the recently released Conveyor Equipment Manufacturers Association’s (CEMA) Belt Conveyors for Bulk Materials, 7th edition, that deal with safety and maintenance. The most effective way to improve conveyor safety is through designing out hazards in the earliest stages of a project. When the safest way to perform maintenance is also the easiest, mechanics will naturally take the obvious and least hazardous approach. IMPORTANCE OF ACCESS Studies have shown that mechanics spend almost one-third of their time accessing the components to be serviced and approximately 25% of all fatal conveyor accidents occur during maintenance1. Chapter 2 of Belt Conveyors for Bulk Materials deals with design considerations. In Chapter 2 there are recommendations for access at the various sections of a typical conveyor for cleaning, inspection and maintenance. While, in some cases, providing access will increase the cost of the conveyor system there can be significant paybacks in reduced injuries, faster maintenance and easier cleaning. Piping and Conduit One of the significant recommendations in Chapter 2 for access is to restrict the mounting of piping and conduit to the conveyor structure in the Loading and Discharge zones of a conveyor. Piping and conduit are more permanent fixtures than maintainable components and should be located out of the way of components needing frequent maintenance. If electricians and pipe fitters are given convenient locations to make their runs they will natural use them. Flexible conduit and hoses can be used to connect to components from pipe racks and cable trays which further enhances maintenance. Access for Cleaning Another critical aspect of access is for cleaning. Approximately 33% of all fatal conveyor accidents occur while cleaning spillage and carryback under and around conveyors2. In the loading zone having sufficient height under the conveyor for cleaning increases the cleaning interval and allows for safer cleaning. In the discharge zone having adequate access for belt cleaning installation has a direct effect on the ability to install a proper cleaning system and perform maintenance."

Jan 1, 2015

Using a Mark IV surface force apparatus, adsorption of dodecylamine hydrochloride on mica has been studied at pH 5.7 in the presence and absence of octanol. With amine alone, the repulsive forces between mica surfaces are reduced due to charge neutralization and attractive hydrophobic force; however, the latter is of relatively short-range with its decay length less than 2 nm. In the presence of amine and octanol, the hydrophobic force becomes more significant, its decay length being extended up to 6.5 nm. The increased hydrophobicity in the presence of octanol is attributed to the co-adsorption of the neutral surfactant with dodecylamine, which increases the packing density of hydrocarbons on the mica surface. The increased hydrophobicity due to co-adsorption is reflected in the improved floatability of silica when using octanol as an extender.

Jan 1, 1993

By K. Oraee

Mining Ventures are considered as high risk projects and therefore managing the risks is inevitable. Risk assessment is an important part of the complex process of risk management, hence applying appropriated and practical methods for ranking the risks associated with projects, can help to perform a better risk management. In this research the applicability of using Techniques for Order Preference by Similarity to Ideal Solution (TOPSIS) method for risk ranking in an underground mine, extracting by block caving method, was studied. Via this method, the risk associated with reserve estimation ranked as the first while in conventional method (P-I Matrix method) located in the sixteenth. Also there were significant differences in ranks of the other risks. Considering the more criteria, with different weights, in comparison with conventional methods, the results comprised from TOPSIS method are more reliable. By implementing this method risks are ranked better and more realistic and consequently then will be managed more efficient.

Jan 1, 2011

By Shiro Ishii

When construction sites are in a densely- populated area or near roads, railroad or river, restrictions upon the ways of handling and using explosives such as dynamite and large demolition equipment are being increasingly stringent, in consideration of environmental pollution such as noise, vibration, dust, flyrocks etc., and safety precaution. In view of this, the development of safe and pollution-free technology for demolishing rocks at mines and reinforced concrete structure at building sites is strongly required. To meet such requirements, the demolition by means of expantion of mineral substances has been considered long before. Recently with the demolition technique using non-explosive demolition agent developed by ONODA CEMENT CO., LTD., holes are drilled into substances to be demolished, such as rocks and concrete before-hand. Then, slurry of such agent mixed with an appropriate quantity of water is poured into the holes. It hardens and expands with the passage of time, and the expansive stress reaches more than 3m/m2 in 10 to 24 hours. This expansive stress causes the material to crack. In this article, descriptions of the non- explosive demolition agent, BRISTAR manufactured by ONODA CEMENT CO., LTD., TOKYO, JAPAN, are given briefly with regard to its physical and chemical properties and its method of use; and the way it is used at an actual construction site is reported.

Jan 1, 1982

By T. Bui

The shut-off value for a panel cave mine determines when a draw point will be shut-off and mining will cease from that draw point. Using a shut-off value strategy for a panel cave mine is similar to using a cut-off value strategy for an open-pit mine. This paper will discuss how to choose an appropriate shut-off value strategy that an engineer can use when planning a panel cave mine to increase the net present value (NPV) of the project. Using a shut-off value equal to the mining and processing cost will provide the total mining reserves for a panel cave mine given a specified footprint. When the net present value analysis method is used to compare one design to another then using a shut-off value greater than the mining and processing cost will generate a higher NPV. This strategy will replace the marginal ore at the top of a draw column with higher grade ore at the bottom of newly opened draw points. A draw column is broken material which sits above a draw point and it is mined to a specified height above the draw point. This height is called the height of draw (HOD). Varying the shut-off value over the life of the mine can increase the NPV even further. This strategy would have a high shut-off value during the early stages of a mine and low shut-off value during the later stages. If the shut-off value is too high then too many tonnes would be left behind the draw point and the overall value of the mine will be decreased. Also with a high shut-off value then the production target may not be maintained due to too many draw points closing too soon.

Feb 23, 2014

By C. P. Mangelsdorf, Richard A. Allwes

At the request of the U.S. Department of Labor, Mine Safety and Health Administration (MSHA), the U.S. Bureau of Mines evaluated the suitability of using tri-sets for protecting mine personnel in roof-fall prone areas. A steel-set arch provided by MSHA served as a basis for evaluating the performance of the tri- set. All tests and analyses were conducted according to the arch canopy test and design procedures developed by the Bureau. Theoretical resistance functions were established for the steel-set arch and tri-set and were representative of their experimental behavior. The resistance functions were used to determine the energy absorption capacity of the structures and to predict their dynamic response to impact loading. The dynamic tests demonstrated that the arch canopy design procedure is appropriate for tri -sets and yields conservative designs for both steel-set arches and tri-sets. As a result of this work, it is recommended that tri-sets may be considered for protection against roof falls, provided that the arch canopy design procedure is utilized for each application and that the principles underlying the design procedure are understood.

Jan 1, 1992

By R. Hawker, P. Singh, K. V. Jessu, P. C. Pinazzi, A. J. S. (Sam) Spearing

Rock bolts are highly important underground to prevent falls of ground and thus, ensure safety. In situ, the ground reinforcement is subjected to a combination of loads, such as shear, tensile, and/or bending loads. Studies have been conducted to evaluate the effect of either shear, tensile, or bending loads on the ground support. However, only a few studies have been done to evaluate the effect of combined load on the rock bolt performance. In situ, the order of loads acting on the bar cannot be predicted, and more than one load can act on the bar at the same time. Thus, a hybrid failure criterion was developed that covered all combined loading conditions. Fifty-eight un-grouted laboratory rock bolt tests were conducted in total under two load conditions: applying shear displacement to the rock bolt and then tensile load to failure, and applying tensile displacement to the rock bolt and then shear load to failure. From the test results, the failure criterion was developed based on regression analysis. A nonlinear relationship was determined for the loading condition variations. The failure criterion presented in this paper can be used as a guide in the rock bolt capacity design under all loading conditions.

Sep 8, 2020

By W. Zhang

"The adsorption of collector on bornite has been studied in situ in aqueous solutions by applying an atomic force microscopy (AFM). The AFM images show that xanthate, such as potassium ethyl xanthate (KEX) and potassium amyl xanthate (PAX), adsorbs strongly on bornite mainly in the form of insoluble metal xanthate, which binds strongly with the mineral surface without being removed by flushing with ethanol alcohol. This adsorption mechanism is very similar to the one obtained with chalcocite/xanthate system. However, the result also clearly shows that the adsorption of xanthate on bornite is totally different from its adsorption on chalcopyrite, during which oily dixanthogen is the main adsorption product on chalcopyrite surface. The obtained AFM images also showed that the adsorption increases with increasing the collector’s concentration. When Cytec Aerofloat 238, a dialkyl dithiophosphate collector, is used, it adsorb on bornite mainly in the form of an oily substance, which can be rinsed off mineral surface by flushing with ethanol alcohol. AFM images also show that the adsorption of Cytec Aerofloat 238 increases with increasing the adsorption time. INTRODUCTION The adsorption of collector on mineral surface is vital for a successful flotation process to achieve a satisfying recovery. Historically, many works have been carried out to clarify the adsorption mechanism of collectors on sulfides. (Gaudin and Schuhmann, 1936, Poling and Leja, 1963; Allison et al., 1972, Fuerstenau, 1982; Leja, 1982; Woods, 1984) Compared to other copper minerals such as chalcopyrite and chalcocite, much less work has been done to study the adsorption collector on bornite. Allison et al. (1972) studied the reaction products of various sulfide minerals with xanthate solutions and reported that the measured rest potential of bornite in 6.25×10-4 M KEX solution at pH 7 was +60 mV and the reaction product of PAX on bornite was cuprous alkyl xanthate. Mielczarski and Suoninen (1984a, 1984b) applied the XPS and studied the adsorption of potassium ethyl xanthate on cuprous sulfide. It was reported that there was a relatively rapid formation of a well-oriented monolayer of xanthate ions followed by a slow growth of disordered cuprous xanthate molecules on top of this layer. Buckley et al. (1984) investigated the surface oxidation of bornite by linear potential sweep voltammetry and X-ray Photoelectron Spectroscopy and proposed the adsorption products on bornite depended on the solution potential. Zachwieja et al. (1987) studied the electrochemical flotation of the bornite-ethylxanthate system and reported that KEX reacted with bornite through an electrochemical oxidation reaction forming cuprous xanthate between -0.4 and -0.2v (SCE). Hangone et al. (2005) studied the flotation of a bornite-rich copper sulfide ore using thio collectors and their mixtures and reported that the highest copper recoveries were obtained with the diethyl dithiophosphate (di C2-DTP)."

Jan 1, 2016

By A. T. Iannacchione

Recent fatal injuries occurring during pillar retreat coal mining call for better identification of the hazards and recognition of risks. Ground control hazards associated with room-and-pillar retreat mining tend to intensify with depth, requiring extra precautions in the form of additional controls. In many locations these activities are further complicated by local complexities often associated with unique or novel circumstances, such as over-mining or under-mining. One technique recently studied by NIOSH, Major Hazard Risk Assessment (MHRA), may help mine operators to mitigate the risks associated with pillar recovery operations. The approach was trialed at two underground coal mines in southern West Virginia that are currently practicing pillar recovery. The first step in the MHRA process involved reviewing the segments or parts of the pillar extraction mining system and identifying associated hazards and threats to the operation. Some of the high risk hazards at these two sites included: ? Rock fall during pillar extraction covers equipment and injury occurs during recovery operations, ? Rock fall above the roof bolt horizon, potentially injuring ? workers and/or requiring recovery action, ? Rib fall under deep cover, potentially injuring workers, and; ? Strata instabilities associated with subsidence of the interburden due to simultaneously mining two seams in close vertical proximity to one another. The mines? risk assessment teams then considered each threat individually in order to systematically identify potential unwanted events. The top unwanted events were examined individually using structured risk analysis tools. The output from the process includes a list of priority existing controls for monitoring and auditing, and a second list of potential new controls. These controls consisted of: Examples of best practices, ? Enhanced communication, ? Implementing standard operating procedures (SOP), ? Protocols for emergency response actions, ? Effective layouts, ? Efficient monitoring, and; ? Successful audits. This paper documents the process as it unfolded at the two mines, and analyzes the strengths and weaknesses of the MHRA technique as it applies to pillar recovery operations. This work was part of a larger NIOSH research project. NIOSH was responsible for: 1) facilitating the risk assessment process known as Major Hazard Risk Assessment (MHRA), 2) documenting the risk assessment process, and 3) providing mine management with a written draft summary of the risk assessment process. The results of the risk assessment represent the thoughts and opinions of the individual risk assessment teams and should in no way be construed as an endorsement of the risk assessment output by NIOSH or the University of Pittsburgh.

Jan 1, 2009

By G. Buchan

This paper discusses the design of long panels for longwall mining at Twentymile Coal Company (TCC) from conception to implementation. The case study of the long panels at Twentymile includes extensive mine plan reengineering in the early 1990's to world record production months in 1996 and 1997. The obstacles of subsidence engineering, environmental regulations, conveyance, ventilation, equipment design, and continuous miner (CM) development timing had to be overcome to successfully begin longwall production within a 4 year time frame. The background and some detail for each of these areas listed will be discussed to show how the coordination of many facets must be pulled together to implement a successful long panel mine plan.

Jan 1, 1998

By Xinyang Wang

It is believed that sulfur and volatile matter con-tents in coals are the main intrinsic properties to cause the self-heating of coal. Their oxidation at lower temperatures than that of fixed carbon to initiate coal's self-heating should be quantified. This study is aimed to improve the previous mathematical model developed by the authors for studying the coal's propensity for spontaneous combustion. It enhances the model's ability to consider the effects of sulfur, volatile matter and moisture contents in the coal three important factors affecting the coal's self-heating process. Sulfur exists in coal primarily in the form of pyrite which will be oxidized rapidly under suitable conditions. Volatile matters, higher in low rank coals, are more easily to be oxidized. Heat of water condensation provides initial energy for low temperature oxidation. Heat release rates for pyrite oxidation and moisture condensation are built in the model. Finally, the simulation results in terms of time versus temperature on pyrite oxidation and moisture condensation are validated with the adiabatic testing data respectively.

Jan 1, 2013

By F. C. Turin, T. L. Friend, A. G. Mayton, J. S. Jaspal, W. J. Wiehagen

This paper describes the serious injuries that have occurred to bulldozer operators working at domestic coal, metal and nonmetal mines in the United States. A serious injury is defined as one that results in either a fatality or in lost work time. Examined were 873 injury records compiled by the Mine Safety and Health Administration (MSHA). The time period covered was 1988 through 1997. These injuries resulted in 18 fatalities and 31,866 lost work days. All of these injuries occurred to dozer operators while they were performing common production tasks. An injury classification system was developed to code the narrative information that describes the circumstances surrounding the injuries. Jolts and jars accounted, for 604 or 70% of the serious injuries to bulldozer operators, and jolts and jars accounted for 75% of the workdays lost. Vertical jars comprised the largest set (354 incidents) of jolting and jarring injuries. In more than half of these incidents, the operator was backing up the dozer. Working near an edge carries significant risk for fatal injuries. Of 116 incidents where the dozer fell over an edge, rolled over or fell into a hidden void, 14 (12%) resulted in fatal injuries. In cases where the dozer operator either jumped or was thrown out of the cab in a fallover or rollover, seven out of 17 of the operators were killed. This study finds that further reductions in injury risk would require more widespread use of seat belts; consideration (and maintenance) of the seat and seat suspension systems that might reduce injury risk from jolts and jars; research interventions to assess the effect of alternative engineering designs to dampen or isolate the effects of shock and vibration; and continued attention to skilled performance, i.e., the integration of hazard awareness, recognition and response with dozer operational skills.

Jan 1, 2003

By M. Allan Holtz

The shipment of coal, ores, and minerals in bulk form during the winter months presents a difficult problem in emptying rail cars. U. S. Steel Research in cooperation with U. S. Steel Coal Operations bas laboratory tested and field monitored the effectiveness of using freeze conditioning agents (FCA) to minimize the frozen coal problem. This report examines, in an overview manner, our experience after four seasons of treatment using different FCA agents on raw and preparation plant products. Our observations indicate that if an FCA is applied correctly it is effective mineral to mineral. Freezing problems still occur at the interface between the coal and the metal of the car sides and bottoms. Leading chemical suppliers have made positive improvements in their FCA formulations with second and third generation products. Further advances are needed to make chemical treatment for the prevention of frozen coal a real full-proof method.

Jan 1, 1980

By Rajat Gangrade, Haotian Zheng, Jarrett Smith, Daniele Nebbia, Mike Mooney

The application of artificial intelligence (AI) to improve tunnel boring machine (TBM) operations requires a significant amount of information to train robust performance prediction models, e.g., for tunneling-induced settlement, productivity, tool wear, etc. This paper presents the AI framework applied to the North-East Boundary Tunnel (NEBT), the largest component of the Clean Rivers Project in Washington, DC. The paper focuses on required elements for real-time AI use to estimate tunneling-induced ground and building deformation and cutter tool wear. Keys to the framework include defining the necessary quantities of data required as well as the process of windowed training, validation and model testing. To date, the models developed for ground deformation and tool wear show satisfactory performance when compared to observed field observations during tunneling.

Jun 13, 2021

By C. Stoneback

The attapulgite industry saw a year of solid growth after a weaker 2003. Demand was up between 5 percent and 6 percent driven by almost all of the key markets. Construction continued to show record new housing demand, assisted by continued low interest rates. That drove strong growth in construction related markets like coatings, tape joint compounds and other construction materials applications. The agricultural markets rebounded modestly to increase sales for suspension fertilizers, animal feeds and pesticide carriers. Oil drilling also showed strong growth due to high oil and gas prices. Sales to molecular sieve applications grew due to petrochemical and construction demand. The export markets were assisted by further depreciation of the dollar. The only weak area was in nonagricultural granular sorbents, where other sorbent materials continued to dominate.

Jan 1, 2005

By T. I. Nelson

Natural aggregates, primarily stone, sand and gravel, are recovered from widespread, naturally occurring mineral deposits and processed for use primarily in the construction industry. They are mined, crushed, sorted by size, and sold either loose or in concrete products to build roads, houses, buildings, and other structures. Smaller quantities are used in agriculture, cement manufacture, and industries employing chemical and metallurgical processes. The growth of cities, their buildings and the highways that connect them have created demand for enormous quantities of aggregates. The aggregates industry is the largest mining industry in the United States in terms of production by weight, volume and by number of active operations.

Jan 1, 2005

By K. Biswas

For the pillars, which have been standing long after mining, the stability depends much on the weathering action in the presence of mine moisture. From the field observations, it has been found that this weathering action becomes critical in terms of pillar stability if the coal seam contains partings or binders in it. The weathering action degrades both the partings and coal in terms of their load bearing capacity as the mine moisture penetrates into them. This paper investigates the effect of weathering action on coal and partings in the laboratory. In the field, the strength profile in the coal and the partings and the effect of time (in terms of the pillar age) on them have been studied by using borehole penetrometer. In this paper, an attempt has also been made to establish formulae for time dependent strength of coal and partings.

Jan 1, 1997

By Oscar Cabello, Luis Mendieta, Maribel Guzman

Mineral flotation processes generate large volumes of tailings, which must be disposed of efficiently and safely. In addition to dry stack disposal, the possibility of reusing these tailings as aggregates in shotcrete is an interesting alternative. Tailings samples from a mining operation in southern Peru were characterized by granulometric analysis, X-ray diffraction and Scanning Electron Microscopy. Concrete samples were obtained with different tailings formulations. The samples were subsequently subjected to geomechanical testing. The results showed that replacing 20% to 30% of the tailings with aggregates in shotcrete production achieved compressive strengths exceeding 30 MPa after 28 days of curing, with an energy absorption capacity of 500 joules. Results show that this shotcrete can be used in the support stage of the mining cycle in underground mining.

Feb 22, 2026