Search Documents

By W. F. Riggs

1 Flotation Analogy To explain flotation in simpler terms the following analogy will be used. A factory (the flotation cell) manufactures a product (collector coated mineral). The product (collector coated mineral) is transported to market (the launder). A truck (the frother) is used to transport the product (collector coated mineral) to the market (the launder). The truck (the frother) transports the product over a road (the froth bed). The truck (the frother) and product (collector coated mineral) are supported by tires (the air). 2 Assumptions This operating philosophy assumes that the correct collector dosage is present along with the correct particle size distribution, pH conditions, etc. and that the minimum required frother dosage is correct. 3 Collector Addition The collector addition as used at a flotation plant is based on dosage rate as determined by the amount of mineral value entering the concentrator. Collector is normally added at two points in the concentrator: The primary flotation circuit and staged addition in the rougher scavenger circuit. Surveys have shown that the staged collector addition provides an increase in the kinetics and increases the recovery of the valued mineral in the rougher scavenger circuit. 4 Frother 4.1 Frother Dosage As explained in the above analogy, frother can be likened to the truck that transports the product (collector coated mineral) to market (the launder). Just as you would not use a truck rated at 15 tonnes to transport a 20 tonne load, you cannot expect to transport coarse minerals to the launder when there is insufficient frother present. Frother dosage must always be at, or above the minimum target. If less frother than the required minimum is used, then coarse mineral particles will not be supported and transported to launder where the mineral is recovered. To the naked eye the froth characteristics, even when insufficient frother is used, will appear to be correct. You cannot see the coarse particles that are not being recovered in the froth. (See Section 4.2 below for an explanation of why this occurs.)

Jan 1, 2006

By Georgene Renner, William R. Yernberg, Steve Kral

Advanced Terra Testing (ATT)is a full-service geotechnical testing laboratory. It specializes in rock and soil mechanics and geosynthetic materials testing. ATT provides services to the global mining industry. The company has performed more than 1,000 projects for more than 300 commercial and government clients. Services include coal pillar design testing, leach pad material and performance testing, tailings pile consolidation testing and closure and remediation services. Rock and soil mechanics tests include unconfined and triaxial strength, shear and tensile strength, permeability, index testing, consolidation, liquifaction potential, elastic moduli determinations, heap height versus percolation rate, long-term batch testing and dynamic loading tests.

Jan 1, 2003

By R. Snoby

Since its introduction in 2002, the modern air jig has processed a wide array of coals throughout the world. This paper explores the reasons and justifications for the installations and provides case history performance data. Specifically highlighted are air jig plants processing metallurgical coal in Colombia, bituminous coal in the United States and India and lignite in the United States and Spain. Each installation has unique reasons to justify an air jig facility. It is important to note that not all of the justifications were based on the ?most cost effective yield?, normally a mantra for coal preparation plant designers and owners. Dry jigging of coal has long been a proven technique for upgrading coal, the modern air jig, with its improved efficiency and operating systems simply extended the range of applications. In some cases, it even allows market quality coal to be produced when no other option is possible.

Jan 1, 2009

By Dan Witkowsky

In an increasingly environmentally conscious world, mining's importance to society has often been misunderstood and even maligned by the public. Extreme and impractical ideas have often been presented to children because of the lack of accurate, timely resource materials available to educators. In the late 1960s. two mining engineers, S.P. "Pi" Warren and C.L. "Lindy" Barker, became aware of this situation. They proposed to develop a summer field course to provide a factual overview of the minerals industry for teachers. The pair believed that teachers could become better informed to educate students, and future generations, about mining. These two Colorado Mining Association (CMA) members felt that such a course could reduce much of the misunderstanding about this vital industry. This could be done by providing a balanced perspective of mining, not only for kindergarten-through-grade-12 teachers, but also for the students they would be teaching during their careers. Students who better understood the minerals industry could better formulate an unbiased view of it. The course would seek recognized authorities from industry, academia and government who would lecture in their respective fields of expertise. The course would provide a total concept of the coal, aggregate, metals and industrial minerals industries. It would include geology, geophysics, exploration, mining, processing, marketing, product applications, economic, mining history, careers, and environmental responsiblity. When possible, site visits would permit educators to view operations and to meet the men and women who are industry leaders. Teachers would pay a small tuition fee. The balance of the program expenses for each teacher would be paid through scholarships provided by industry and individuals. The "total concept" idea obtained the support of the minerals industry. The support of CMA's Education Committee and the Colorado School of Mines (CSM) was obtained in 1968. Colorado's Commission on Higher Education approved teacher recertification credits through CSM's Office of Special Progams and Continuing Education for those successfully completing the program. The first six-week series of classes presenting the total concept of the indus¬try was held at CSM in 1969. In 1977, the CMA Education Foundation Inc. (CMAEF) was established as a Colorado nonprofit corporation. The "Total Concept of the Mining Industry" (Total Concept) course was placed under its sponsorship. CMAEF is dedicated toward this continuing education program (Table 1). In 1994, the course was streamlined to four-weeks for six hours recertification credit.

Jan 1, 1997

By K. Fountain

In Novemeber of last year I visited a mica mine in Hunan Province, China. For nine months , we had been trying to sell Chinese mica to a customer in Belgium. Talking to the customer was like negotitating with a stone wall. The buyer refused to communicate any -thing other than his steadfast refusal to consider Chinese mica. He would not advise us what he wanted, what specifications or grades. He would give no indication if our price at market, or reasonable, or totally out to lunch. He would not even accept samples. It took no genius to guess that the mica buyer had at some time in the past bought a shipment of Chinese mica and had received a disaster. I invited the mica mine in Hunan in order to see for myself what could be done - without massive investment in equipment and instruments - to upgrade the quality of the mica for export. We had seen this type of customer reaction before. One disgruntled customer who had pur¬chased pigment grade barites direct from China ranted and raved about unreliable and inconsistent quality. It did no good to explain to him that China is a big country, with hundreds of mines scattered throughout many areas, each producing a different product. Our further explanation that Chinese export organizations also varied in degree and efficiency of customer service fell on deaf ears. Samples had no effect on his perception. Eventually we showed him photoraphs of two mountains of pigment grade barites. One lot was our sales of pigment barites to a major European minerals processor. Our Chinese barites stood proudly white and beautiful next to a hill of other material which now appeared at best mediocre and dull by comparison, and which the buyer had decided to reject after he received our Chinese barites. Finally the customer was sufficiently impressed to look seriously at our guaranteed specification and the outturn analysis performed by our other customer.

Jan 1, 1987

By P. Zhang

A 1989 FIPR characterization study of the future phosphate resources in Florida showed that MgO would be a problem with both the pebble and concentrate as phosphate mining moves deeper. Since the ratio of concentrate to pebble will become higher and higher in the future, reducing Mg content in the concentrate by a small margin would allow blending of a large portion of the high-dolomite pebble. This research was conducted based on that logic. The following six approaches were tested for reducing MgO content in the flotation concentrate: (1) Adding a dolomite depressant in the rougher flotation step; (2) Dolomite flotation on the rougher concentrate with and without grinding; (3) Dolomite flotation on the cleaner concentrate with and without grinding; (4) Scrubbing the flotation feed; (5) Scrubbing the rougher concentrate; (6) Scrubbing the cleaner concentrate. Successful methods include adding a dolomite depressant in the rougher flotation, dolomite flotation on the cleaner concentrate with grinding, and scrubbing the cleaner concentrate in quartz sand. These techniques could reduce MgO content in the final concentrate by 20-40%. The flotation process could achieve a concentrate with the lowest MgO content, but it is the most expensive approach. Adding a dolomite is inexpensive and easy, but the effect is limited. Overall, scrubbing may be the most promising technology for this purpose.

Feb 23, 2014

By A. E. Sears

The intent of geomorphic landform design is to mimic the function of the natural landscape. In a surface mine reclamation application, geomorphic landform design has the potential to mitigate stream loss. This research quantified features of reference landforms and performed computer modeling of a conceptual valley-fill design using geomorphic landform principles. A design was created using published design parameters with a software design tool (Carlson Natural Regrade with GeoFluv). Three additional designs, incorporating field-obtained regional geomorphic landform parameters, were completed and resulted in a geomorphic landform design specific to southern West Virginia. This work illustrates the importance of field determination of the ridge to head-of-channel input and drainage density parameters. Values of ridge to head-of-channel distance measured in this study were consistently an order of magnitude greater than software recommended values (SRV); SRV = 24 m (80 ft) versus field= 220 m (720 ft). Similarly, for the drainage density parameter, the software recommended range is 6 to 9 km-1 (80-120 ft/ac). The field measurements for central Appalachia quantified the drainage density to range from 5 to 5.3 km-1 (67-70 ft/ac). This affects Appalachian valley-fill stream construction by making the stream lengths shorter and the land slopes steeper with straighter headwater channels compared with areas in the southwestern United States. While the application of geomorphic landform design to surface mine sites presents challenges, this work provides support for future applications.

By A. Martikainen, H. Dougherty

"At the Kemi Mine, a recent expansion into the Surmaoja orebody required an increase in ventilation capacity. A new ventilation shaft was built with two main fans. The installation is near the entrance gate and only 1.7 kilometres from the nearest permanent dwelling. The main fans were first taken into use as exhaust fans in October 2014. Shortly after the fan installation, comments concerning fan noise were received from the neighbours. The first noise measurements were taken at the main fan installation site by Outokumpu personnel in March 2015. Due to higher than expected recorded values, during late June, 2015, a two-week environmental noise study was planned by the engineers and executed by a consultant specialized in noise measurement. The measurement results were analysed and compared to the requirements of the environmental permit and Outokumpu’s factory standards. While the measured values at the nearest dwelling were within the environmental permit limits, high noise values were recorded at the fan station. A second two-week study will be performed after construction of the main-fan heating station has been completed. Actions taken will depend on the outcome. INTRODUCTION The Kemi Mine is a part of the Outokumpu chain of integrated ferrochrome and stainless steel manufacturing in the Kemi-Tornio region in Finland. The mine itself is a large underground operation with a production capacity of 2.7 million tons of ore per annum. It is also the European Union’s only chrome mine, and at present (2015) the mine extracts 2.4 million tons of chrome ore per year. Safety, cost-effectiveness, and environmental friendliness are hallmarks of the Kemi Mine. Environmental impact produced by the operation of the mine is limited due to the insolubility of the oxide chromium ore, the gravity-based and chemical-free enriching process as well as the closed circulation system of the process water which serves both the whole mine and the enrichment process (Outokumpu, 2015). Importance of the environmental impact of the Kemi Mine is amplified by its closeness to the cities of Kemi and Keminmaa with the nearest habitants living less than 2 km away from the mine site. To show the cooperation with residents the Kemi mine organizes special “neighbour days” for the habitants of the areas closest to the mine. Also, information letters are sent to the neighbours, when changes that may affect the neighbours are being planned and executed."

Jan 1, 2016

By J. K. Borchardt

The use of statistical design to optimize deinking process design has been studied for the flotation deinking of newspapers. The interactions of two variables are often important in determining flotation deinking efficiency. The interactions can be synergistic or antagonistic. These interactions would not be discovered using the traditional method of varying one parameter and holding the other variables constant. An experiment design in which two or more process parameters are varied simultaneously is required to identify these interactions. A considerable number of conclusions could be drawn about the relative importance of process variables on ink particle size distribution, ink removal efficiency, and flotation yield loss in a flotation deinking process. However, these findings could be influenced by the deinking surfactant and the ink chemistry.

Jan 1, 2001

By Guoqing Li, Hao Wang, Nailian Hu, Victor Tenorio, Jie Hou

This paper presents an algorithm for optimizing the scheduling of trackless equipment in underground mines. With the shortest working interval and maximum productivity as goals, a genetic algorithm (GA) is used to solve the problem, and obtain the optimal working sequence with the most suitable equipment configuration possible. The input for the proposed method is the number of units and capacity of trackless equipment, the production process, ore amount in stopes, and the distance between stopes. The algorithmis verified using four setups of 5 stopes with 5 cycles, 5 stopes with 15 cycles, 10 stopes with 10 cycles, and 10 stopes with 30 cycles. The solution time of the algorithmis no more than 20 min, which is acceptable for practical applications. The results show that the setup of 10 stopes with 30 cycles is closer to the actual production of the mines, and the optimization model can effectively improve the operation efficiency. In this scenario, the robustness of the optimization is tested by simulating equipment failure events. Under the condition of 8% failure rate, the operation time is extended over 3.21–14.56% than expected, which represents strong robustness. The algorithm can quickly provide a feasible and effective solution for the production scheduling decision of trackless equipment in underground mines.

Aug 12, 2020

By K. Biswas, F. C. Felipe

Paste backfill, because of its colloidal or water-holding properties, does not produce run-off water when placed underground. Paste backfill is generally, prepared from relatively low water content, full mill tailings with a certain proportion of ultra-fine particles and mixed with cement, thus producing early and better strength. Mill plant discharge tailings and other materials available at or near the mine site such as sand, aggregates or waste rock are used as blending materials in the mix design. This study investigates the influence of the above-mentioned blending materials on the mechanical characteristics of paste backfill, as well as the grading, shape, specific surface area, mineralogy and workability of the different mix design.

Jan 1, 2000

By Peter J. Szabo

In 1980, a caravan of representatives of Japanese trading companies debarked on the shores of the United States bearing gifts of watches, electronic games, and radios. In early 1983, we find in a parking lot of a major U.S. coal company, a haggard general manager of marketing returning to the Orient with a box under his arm of trinkets of his own; cross pens with company logos, alarm clocks, etc. The tables have turned, but our fellow sitting in a jet plane over the Pacific Ocean had only to heed the warning of the famous 19th Century poet well familiar with the ways of the Far East. Kipling said; "And the End of the Fight is a tombstone white and with the name of the late deceased, And the epitaph drear, a fool lies here who tried to hustle the East."

Jan 1, 1984

By Joseph W. Leonard

Much progress has been made in the application of geostatistics to hard rock ore deposits.1,2,3 4,8 Progress in the application of geostatistics to coal deposits has developed over a period of time out of hard rock technology.5,7 Exploratory drilling in many hard rock deposits is frequently significantly more productive than exploratory drilling in coal deposits. For example, hundreds of feet of drilling and/or many drill setups are frequently necessary to obtain a few samples from a typical 4 to 6 foot thick coal seam. With hard rock deposits, which are frequently thick or volumetric, less drilling dead work is involved in sampling the deposit. To produce a variogram, which is the basic element needed for geostatistical analysis, a few well positioned holes drilled into a hard rock deposit where the core(s) can be divided into many sections can produce a detailed variogram. To produce a similar type variogram in coal, it is necessary to drill many dozens of holes with much of the core length consisting of overburden data which is frequently of only secondary importance. To apply geostatistics to coal, not only are many separate sample sites needed, but frequently a problem exists in that the interval distance between samples cannot be controlled with the ease that hard rock drilling intervals can be controlled where it is only necessary to cut core segments according to some preassigned interval of distance. Because the uses of existing coal deposit samples are frequently handicapped by irregular sample distances and lack of sampling density along certain directions needed for the development of variograms, the application of geostatistics to coal deposits frequently does not proceed with the same efficiency and rapidity as when these techniques are applied to ore deposits. Grid-fitting was developed by the writers, as a logical and evolutionary improvement over the long and successful application of geostatistics to coal seams.6,9 Grid-fitting combines the trending of variance as well as other aspects of probability theory to optimize informational yields from the commonly less productive data derived from coal exploratory programs. Grid-fitting is basically a technique where a hypothesis involving numerous grid patterns, where each pattern is of a given geometry, size and direction is repeatedly matched against actual sample data to determine which match results in the closest fit of the hypothesis to the data. To determine the closest fit, a special index known as a selectivity index was developed. The selectivity index is basically the product of the mean and variance of the variances contained within each of the grids. hence, if SI is the selectivity index then [SI = Xs E (S i - Xs) /N] where [X]s is the mean of individual grid variances Si2 for any pattern of given geometry, direction and size.

Jan 1, 1984

By H. Verakis, M. A. Hockenberry, A. C. Smith, J. H. Rowland III

Four different types of fire suppression systems were evaluated in large-scale fire experiments to study the effect of air velocity on their effectiveness in extinguishing conveyor belt fires. The four different types of suppression system were water sprinkler, deluge-type water spray and two different dry chemical fire suppression systems. The large-scale fire tests were conducted with 1.8-m- (72-in.)-wide fire-resistant rubber belt that met the Mine Safety and Health Administration flame resistant requirement specified in Title 30, Code of Federal Regulations, Part 18, section 18.65 (also known as the 2G Flame Test). Each fire suppression system was tested at air velocities of 152 - 168 m (500–550 ft) per minute (mpm) and 411 - 457 mpm (1,350 - 1,500 fpm). Two tests were conducted at both air velocities for each fire suppression system. Both of the water-based fire suppression systems were able to suppress the fire to the point that a miner could extinguish it with a fire extinguisher. However, the amount of water needed to suppress the fire to the point where a miner could walk up to and extinguish any smoldering belting was greater than the current MSHA regulations required. MSHA regulations only require 10 minutes of water supply for a suppression system. In the test setup, neither of these systems would have suppressed the fire had the water been turned off to the system after 10 minutes. The dry chemical suppression systems produced mixed results. Dry chemical suppression system A did not suppress the conveyor belt fire at either air velocity. Dry chemical system B suppressed the fire at 152 mpm (500 fpm) air velocity, but produced mixed results at the higher air velocity. Details are presented on the large-scale fire test setup, arrangement of the fire suppression systems and conclusions regarding the effect of air velocity on fire suppression system design and performance.

Jan 1, 2010

By Y. Breau, F. Robichaud

The Expert System implemented at the East-Malartic mill controls a copper flotation circuit while taking into account the profitability of the operation. Treating a copper gold ore, the flow sheet integrates a flotation step followed by cyanide leach circuit. The Expert System calculates the actual net smelter revenue of the flotation circuit, accounts for the operating cost of the cyanidation circuit and defines optimal metallurgical operating targets to optimize the overall economics. To be realistic, probability factors and circuit diagnostic analysis are integrated in the operating target selection. The Expert System has proved to be successful, robust and flexible. It resulted in a copper concentrate grade increase of 1% while maintaining recovery. The use of the expert system also gives plant personnel good training procedures and promotes interaction with mill operator.

Jan 1, 2002

By R. G. Bradburn

The events which led to computer control of the grinding circuit at Brenda Mines are described, beginning with mill operating philosophy. High production rates are encouraged so that, despite severe upstream disturbances, a manual control method to meet this philosophy had developed. Unfortunately, due to the time interval between manual control adjustments, losses in production resulted. An analog control method was devised and, although superior to manual control in some situations, was found to suffer from several practical limitations. The data logging capabilities of a control computer seemed warranted. Circuit test- work combined with an analysis of operating data showed that (1) metallurgical personnel, at times could increase production rates by as much as 10 percent over that achieved by grinding operators, (2) the chosen data base required an increase of 2 percent or more to be statistically significant and (3) for a 2 percent increase there would be a significant rate of return of investment in a computer installation, Consequently one grinding circuit was fully instrumented, and a rented control computer was installed by Brenda personnel. Prior to installation, Brenda metallurgical and instrumentation personnel were trained in the use of the computer. An experimental program was devised with short and long term objectives. The short term objective was to develop a practical control strategy which would yield immediate production improvement. This goal has been met as described in this paper. Statistically significant increases in excess of 2 percent have been established. Work is being completed for the permanent installation of computer control on all four grinding circuits at the present time. Long term objectives are (1) off line analysis of the circuit using mathematical models of process units, (2) on line experiments to study alternative contol tactics, and (3) possible expansion of computer facilities to the crushing plant.

Jan 1, 1976

Current design guidelines for the surface catalysed oxidation of Fe(II) on Fe(OH)3 (Ochre) in passive mine water treatment systems are based largely on empirical data as the details of rates and mechanisms have not fully been revealed. Also the effects of elevated carbonate concentrations, typical of many UK minewaters, on the surface catalysed oxidation rate are unclear. In order to move away from empirical design and towards sound engineering that is based on geochemical and hydrological understanding it is necessary to quantify these reaction rates. In this study the effects of Fe(OH)3 and carbonate on the rate of Fe(II) oxidation by dissolved oxygen have been investigated with an aim to delineate the reaction mechanism. Experiments were conducted under well-controlled conditions. Preliminary results indicate that the surface catalysed reaction is an order of magnitude faster at pH ~6.4 with 200 mg/l Fe(OH)3 than the homogeneous rate and is dominated by an elevated rate of removal and oxidation of Fe(II) from the solution phase. It is also apparent that the oxidation rate of actual adsorbed Fe(II) is substantially retarded with respect to the homogeneous rate. Carbonates were not shown to affect the surface rate within the bounds of this preliminary study.

Jan 1, 2006

By Mahiyar Nasarwanji, Jonathan K. Hrica, Jonisha P. Pollard, Lydia M. Kocher, Brianna M. Eiter

Within the metal/nonmetal mining sector, fall-related incidents account for a large proportion of fatal and nonfatal injuries that occur in mining in the United States. However, the events and contributing factors leading up to these incidents have not been fully investigated. To help provide a clearer picture of these factors, an analysis of imminent danger orders issued by the U.S. Mine Safety and Health Administration (MSHA) from 2010 through 2017 at both surface and underground metal/nonmetal mine sites revealed that most orders are associated with fall risks. Of these cases, 84 percent involved the workers not using fall protection, fall protection not being provided or the improper use of fall protection. Fall risks for workers most frequently occurred when standing on mobile equipment, performing maintenance and repairs on plant equipment or working near highwalls. In most cases, a single, basic, corrective action — such as using fall protection — would have allowed workers to perform the task safely. Overall, these findings suggest that a systematic approach is needed to identify, eliminate and prevent imminent danger situations. Furthermore, to protect mineworkers from falls from height, frequently performed tasks requiring fall protection should be redesigned to eliminate the reliance on personal fall protection.

By T. Lilley

The use of membranes in wastewater systems has increased rapidly in recent years. Microporous or semi-permeable barriers augment conventional chemical or biological processes to meet stringent treatment targets. These developments enable elegant solutions to wastewater discharge challenges and extend the scope of water recycle redressing the overall water balance and operational economics Wastewater treatment processes are discussed by reference to the spectrum of waterborne contaminants and the respective membrane separation capabilities. The role chemical pre-treatment to enable physical separation of metals with micro-filtration (MF) is described and how integration of MF with reverse osmosis (RO) is used to control a broader range of dissolved contaminants Membrane configurations are considered apropos function, operational economics and sustainability. These features are exemplified with case studies. Firstly, MF alone following chemical precipitation for the removal of heavy metals, then MF onto two stages RO of different configurations for TDS reduction and waste volume minimisation and finally an open channel RO alone for the reduction of inorganic COD from a leach stream.

Feb 27, 2013

TABLE TUNNEL NAME OWNER LOCATION STATE TUNNEL USE LENGTH (FEET) WIDTH (FEET) BID YEAR STATUS Gateway Tunnel project Amtrak Newark NJ Subway 14,600 24.5 2015 Under study

Sep 1, 2013