Search Documents

By B. D. Paphane

Since the commissioning of the Tati Hydrometallurgical Demonstration Plant (HDP), which produces Ni and Cu cathodes as well as Co salt from sulphide concentrate employing Activox® technology for leaching, no kinetic data has been generated from the plant under normal operating conditions, from start-up to steady state. Therefore, this study seeks to determine the rate of reactions in the leaching circuit with a view to obtaining kinetic data for the system under the current operating conditions. Within the five-compartment autoclave operating at temperatures of 105°C to 110°C and 1100 kPa pressure, the extraction of Ni, Cu, and Co ions into solution is achieved through the oxidation of the sulphide concentrate using approximately 50 kg H2SO4 per ton, 10 kg NaCl per ton, and 1.21 kg O2 per kilogram of S2-. The autoclave reactions showed complex kinetics, with the reactions proceeding via some intermediate(s) before the formation of products. The results suggest that the reactions were dependent on the size of the metal ion of interest and the concentrations of the metal ions in the Tati concentrate as well as in chloride leaching. The order of the leaching rate constants was Fe2+ > Cu2+ > Ni2+ > Co2+ in all the compartments studied. The rates of leaching were also found to decrease as the concentrate moves from compartment 1 to compartment 4. For compartments 1 to 3, leaching was observed to be preceded by dilution of the repulp liquor (copper raffinate). The leaching rate for compartment 5 was slightly lower than that of compartment 1 but higher than the rates of compartments 2, 3, and 4 for all the metals studied. Keywords kinetics, hydrometallurgical plant, Activox

Jun 1, 2013

By K. L. Morton

Groundwater and associated pore pressure represent elements that can have a negative impact on surface mining and slope stability. Groundwater flow and deformation within a slope influence each other. An increase in pore pressure will result in a decrease of effective stress; and conversely, if the pore pressure decreases, the effective stress increases. Slope analysis and slope design calculations require good information on pore pressure distribution around an open pit excavation. Until recently very little pore pressure data were available and assumptions had to be used. Location and design of measuring points depend on geological and structural setting, geotechnical domains and practicality. Good planning and the use of sensitive point piezometers to measure in situ pore pressures means that real-time data can be collected and used for the construction of flow nets, the determination of pore pressure distribution around an open pit mine, the validation of the dewatering/depressurization requirements, the calculation of the efficiency of the dewatering system and finally the use of pore pressure data in slope stability analysis. The recommended layout for a monitoring system, types and design of piezometers, data collection and use of the pore pressure data are presented.

Jan 1, 2008

By Willem C. A. van Niekerk, David A. Baldwin, Nardus Potgieter, Willie A. Gericke

Authorities that regulate environmental issues pertaining to industrial wastes in South Africa regard landfill disposal as the only effective environmental management option for slag and other inorganic by-products from the ferro-alloy industry. Metallurgical slags are widely utilised in civil engineering and construction applications in other countries in the world and in line with the overall philosophy of conserving mineral and other natural resources, these materials should be assessed for the possibility of resource recovery, recycling, reclamation, direct re-use or alternative uses. This presentation describes a risk-based approach for the assessment of by-products from the ferro-alloy industry for alternative use. Once a by-product from an industrial process has been identified for alternative use, its intended use would be defined, but it will not be possible to control its actual use or misuse in society, nor will it be possible to control its fate during the application life cycle. In the interest of protection of human health and the environment, potential risks associated with the handling and uses of a material throughout its life cycle therefore have to be quantified. The assessment has to include both human health and ecological risks and must cover the entire life cycle of a product, from its production up to its end-of-life disposal. The presentation introduces the concept of tiered risk assessment and demonstrates how this applies in the overall assessment of by-products from metallurgical industry sector for safe use in society.

Jan 1, 2007

By Hao Li, Allan Moss, Richard K. Brummer

At the Palabora Mine, the transition to caving 400 m below the bottom of the 800 m deep pit resulted in a slope failure of the North wall that began in 2003, and is still mobile. This failure can be explained by the daylighting into the cave zone of a prominent joint set. The failure was modelled by the 3-dimensional code 3DEC, which is capable of modelling the nonlinear behaviour of discontinuum materials with large displacement.

Jan 1, 2006

By R. E. Wilmot

The problem of corrosion of reinforcement in concrete structures is internationally recognised and represents the single biggest expenditure in the preservation of steel reinforced concrete structures. While the corrosion protection of the reinforcing steel is no substitute for design and the placement of good quality concrete, it does provide for a viable and economical extension of structural integrity and service life in the day-to-day and practical environment in which concrete structures are constructed. The mechanism of corrosion attack and consequent deterioration of reinforced concrete structures is well understood and documented. New structures can be designed and built to withstand corrosion. However, due to short-term economical restraints, many new reinforced concrete structures continue to suffer as a result of corrosion damage, which results from the corrosion of the steel reinforcing. This paper explores the economic and practical benefits offered by the application of hot dip galvanizing as a viable means of protecting reinforcing steel concrete structures. The paper also discusses technical misconceptions that exist with respect to the application and performance provided by the use of hot dip galvanized reinforcing steel.

Jan 1, 2006

Decision-making regarding plant-scale reagent dosage regimes and air rates is a topic of ongoing investigation and high importance. The current work explains some techniques that have proven useful in deciding on plant-scale flotation operating regimes. Specific focus has been placed on the reagents: frother and depressant, as well as some discussion around the control of air rate and froth depth. Air rate has been selected based on its effects on the froth phase. Froth velocity and froth height above the cell lip are the two variables measured and used to select the operating air rate. Pulp level is then adjusted to increase or decrease mass pull. A technique has been developed using the Anglo Platinum Bubble Sizer on an industrial flotation cell to determine the relationship between bubble size and frother concentration. This technique has been extended to measure the equivalent frother concentration or frothabilities of various streams on a rougher bank. A mass balance for frother was performed successfully, and this provided a better understanding of the way frother moved in the rougher bank. With this knowledge, more informed decisions can be made about frother addition required in subsequent flotation stages. For depressant, a new protocol for deciding on dosage rate has been developed. The depressant dosage should be based on the amount of fresh feed material reporting to a bank. Currently 400 g per ton of fresh feed has been assumed a reasonable starting point, with promising results. Improved froth stability and grades were observed. There is scope for more accurately defining the optimal dosage rate. Importantly, the combined effect of changing the chemistry and the hydrodynamics together has been demonstrated. A significant upward shift in the grade-recovery relationship for a cleaner bank was observed.

Jan 1, 2013

By A. N. Clay

In recent times, there has been criticism of the minerals industry over the lack of quantifiable boundaries between inferred, indicated, and Measured resources. A recent initiative through the United Nations aims to try to converge the mineral resource classification systems. Since the oil and gas industry uses a probabilistic approach to defining reserve boundaries, it is appropriate to introduce a similar statistical methodology for minerals. The Venmyn Variance Tower has been developed based upon traditional statistics to utilize historical and ongoing information in order to quantify variance of geological and chemical parameters and the boundaries and logic for quantitative mineral resource classification. It is proposed that a less than 50% variance from the mean of all sample parameters is required to achieve the classification threshold to define an inferred Resource whereas between 20-10% is needed for an indicated Resource and less than 10% variance from the mean is needed to declare a Measured Resource. These limits are similar to those used by the oil and gas industry, and it is suggested that these thresholds be adopted as an industry standard to ensure consistent quantitative reporting. While this process is intended to use statistics of an orebody to provide quantifiable and defendable boundaries, it cannot be carried out unless the geology of the mineral deposit is understood and the borehole samples can be categorized into appropriate populations for which the statistics are valid. This means that competent geologists are always required to work with and understand the implications of the Variance Tower results. This paper is intended to form the basis of a series of publications that establish a process to take mineral projects along a quantifiable and logical development path. Hence, no specific field example of the practical application of this process is given here.

Jan 1, 2012

By M. F. van der Merwe

Anglogold Ashanti?s Kopanang Gold Plant (previously No. 9 Gold Plant) treats ore from Kopanang and Tau Lekoa shafts. The plant is twin streamed and has dedicated treatment circuits, from milling to final product, for each shaft. Waste rock material is used to compensate for the mill gap on both streams. Each stream consists of three 4.85 m x9.15 m ROM mills in closed circuit with a single stage hydrocyclone, milling an average of 7 000 t per day. The liner configuration in each mill consists of six rows of 30 grid liners along with rectangular lifter bars. The topic of gold lock-up is not new and has been investigated and reported on many times, both within Anglogold Ashanti and the broader mining industry. Although the lock-up mechanism is understood, its measurement is neither practical nor precise. The initial lock-up in a new liner and the release as the liner wears down cannot be accurately quantified. Previous test work carried out on Kopanang Gold Plant (with a ?gold scanner?) measured the natural gamma radiation emitted by uranium. This radiation is in proportion to the mass of concentrate locked up in the grid liner pockets, as well as between the cast-on backing plate and the shell. The ratio of concentrate lock-up was estimated as 35% behind the liners and65% in the pockets. Mill gravity concentrates are recovered during routine relining operations from behind the grid liners at Kopanang Gold Plant. Prior to relining, the liners tend to release the concentrate from the pockets as the liners wear. Historical Kopanang data from actual ?mill gold? smelted indicates that an average of 29 kg gold is recovered from behind each row. This indicates a total lock-up of 250kg gold per mill. This locked-up gold should preferably be minimizedor eliminated for the following reasons: ?The cyclic build-up and release of gold in mills complicates accounting ?Gold concentrate arising from liners is a security risk and creates a major mechanism for gold theft ?Loss of interest on the value of 250 kg fine gold is significant and was a major driver for the project. These factors led to the need to develop techniques to eliminate or at least minimize the gold lock-up in the mills. Wave liners, with rubber inserts, have been successful in eliminating lock-up, and were tested at Kopanang Gold Plant in November 2000. However, due to increased load-slip and high wear rates associated with these liners, this option proved less economical in terms of liner wear. Grid liners, with rubber-filled pockets, demonstrated a very high wear life and eliminated pocket lock-up. This system was successfully trialed in January 2003, but unfortunately did not prevent lock-up behind the liners. Current developments have resulted in a system that eliminates both pocket and backing plate lock-up. The conventional grid liner design has been modified to remove its steel backing plate. Rubber inserts that are integrated onto a rubber backing plate, have been designed to be used with the newly modified grid. The backing plate and grid pockets are now completely occupied by rubber, thus completely eliminating concentrate build-up around the new grid liner system installed in November 2003. Results to date are promising and liner life is expected to exceed conventional performance.

Jan 1, 2005

By M. Tangstad, J. D. Steenkamp

In April 2013 a 48 MVA submerged arc furnace producing silicomanganese was excavated in South Africa. Since the high shell temperatures recorded in the tap-hole area resulted in the furnace being switched out for relining, the tap-hole area was excavated systematically. A refractory wear profile of the tap-hole area with affected hearth and sidewall refractory was obtained in elevation. The carbon ramming paste in front of, above, andbelow the tap-hole was worn, as was the SiC with which the tap-hole was built. A clay mushroom formed but was detached from the refractories. Thermodynamic and mass-transfer calculations were conducted to quantify the potential for wear by chemical reaction between refractory and slag and refractory and metal in the tap-hole area. It was found that chemical reaction between refractory and slag or metal could offer only a partial explanation for the wear observed; erosion is expected to contribute significantly to wear.

Jan 1, 2015

By H. Gumede

The occurrence of fracturing due to high stress levels is a major factor in hangingwall stability in deep level gold mine stopes. However, rock falls cannot be the result of these fractures alone. Rock falls can result only from the occurrence of unstable rock blocks defined by the interaction of the stress induced fractures and naturally occurring geological planes of weakness. These planes include bedding planes and joint set planes. However, there is a general lack of information on the characteristics of these planes (orientations, spacings and lengths)?it does not appear that any such systematic and quantified information, if collected, has been published. To remedy this situation to some extent, joint mapping exercises have been carried out in several geological environments in two gold mines. The data collected on joint geometry included orientation, spacing and length, and this information is included in the paper. In addition, the paper describes the use of the data collected to evaluate the potential for rock falls and the probability of failure of stope support

Jan 1, 2007

By K. Lomberg

In this paper the process of sampling and assaying as it relates in particular to the platinum group elements (PGEs) is presented. A discussion of the geology of PGE deposits is included to provide an understanding of the mineralization that is considered necessary prior to sampling, as this has a direct bearing on the mineral resource estimate and also the selection of an appropriate mining cut. The discussion includes the selection of the sampling technique (drilling or face sampling), the size of the sample relating to the requirements of the laboratory, the potential mining cut, as well as a reference to sampling theory. The selection of an assay technique that is appropriate and will yield the optimal result based on sample turnaround, precision, accuracy, and cost is then considered. Examples are drawn from work undertaken on the Bushveld Complex (Merensky Reef, UG2 Chromitite Layer, Platreef) and Great Dyke (Main Sulphide Zone). A discussion of the appropriate QA/QC programme includes the chain of custody, CRM selection and the QA/QC process. Keywords sampling, assaying, QA/QC, platinum group elements.

Jan 1, 2014

By C. Ware, R. Uken, G. Whitmore

The coastal dune cordon of northern KwaZulu-Natal is among the highest in the world reaching heights in excess of 180 m and up to 2 km in width. It comprises a complex system of Quaternary stacked dunes of various geomorphologies, types and ages (Sudan, 1999; Maud and Botha, 2002;Ware et al., 2001; Ware, 2003). The dunes contain economic heavy minerals that have been exploited for the last two and a half decades. Dune units have recently been defined based on sand composition and texture(Sudan, 1999; Ware, 2003). Despite this, little work has been undertaken on the clay-fraction (< 2 um). This work documents the weathering of dunes to form clays. From the documented clay assemblages and relative abundances, a simplified weathering sequence with increasing maturity can be summarized as follows: primary minerals ? illite + vermiculite ?illite +interstratifications ?illite + montmorillonite ?halloysite + interstratifications + kaolinite ?kaolinite. The dominant controlling factors in determining clay assemblages is pH and leaching conditions. The presence of carbonates results in an alkaline pH and high concentrations of Ca2+and Mg2+which favours the formation of montmorillonite and vermiculite. However, vermiculite tends to form under slightly acidic conditions and is indicative of palaeosols where organic acids produce localized acidic pH’s. In contrast to this, kaolinite will only form and concentrate when carbonates have been leached. Kaolinite dominated samples are considered very mature under current climatic conditions(Chamley, 1989). Halloysite represents a transitional phase between montmorillonite and kaolinite (Herbillon et al., 1981). Ion mobility and evacuation is also critical in determining clay assemblages. Past work and field studies indicate that the dune cordon acts as an open system, resulting in carbonates and mobile ions being readily leached and lost from the system. However, when prolonged weathering has caused an accumulation of fine-grained material, the permeability decreases substantially whereby mobile cations and silica cannot be readily evacuated. This results in the formation of montmorillonite rather than kaolinite, even when carbonates have been leached. Illite (sericite) is considered to alter directly from feldspars. However, dune stacking and geometries, vegetation, water fluxes, reworking and erosion complicates this sequence.

Jan 1, 2003

By Frik Badenhorst, René Roux, Peter Terbrugge

This paper presents a case study where economics dictated an aggressive slope angle and where an appropriate slope management programme allowed successful completion of mining to 190m below surface. The Navachab Gold Mine is located in Namibia and is one of the few gold mines in that country. Mining by open pit methods commenced in 1990 with economics dictating an aggressive slope design to minimise waste stripping and make the mine viable. With steep slope angles in the design, and a steeply dipping footwall geology, it was necessary to introduce a comprehensive slope management programme. This required good mining practice in limit blast techniques with pre-splits and trims, and good housekeeping to effect a safe and economical operation. The slope management programme in addition required in pit mapping and logging procedures, regular survey monitoring evolving to a robotic Geomos system, as well as slope instrumentation to monitor stability. Two relatively large scale failures occurred at the mine, the second of which impacted on the east wall access ramp, while the first was confined to an operating stack. The paper describes the design and slope management techniques developed for the east wall.

Jan 1, 2006

By D. Vogt

A brief summary of the propagation characteristics of rock provides the necessary understanding to design effective radar surveys. Measurements of the electrical properties of the major Bushveld platinum-bearing horizons and their host rocks show that radar is an excellent tool for both short -and longer-range mapping. Experimental work confirms the performance predictions. High frequency, 500 MHz ground-penetrating radar (GPR) is a first-rate tool for mapping features in the hangingwall of the orebody, locally known as a ?reef?, for the purposes of determining hangingwall stability. The triplet chromitites above the UG2 have been clearly mapped, as has the Leader Seam above the UG2. Borehole radar at lower frequencies has been used over longer ranges to map reef elevation. Potholes in the UG2 are clearly distinguished in range and elevation to within metre accuracy. The nature of the slump in the various footwall horizons is also apparent. In future, as GPR is routinely applied, it is likely to become used for other purposes. Borehole radar is being developed to operate at higher frequencies, which will allow it to be deployed from boreholes that are within 5 m of the target horizon. Keywords: GPR, borehole radar, Bushveld Complex, UG2, Merensky, pothole, triplet

Jan 1, 2005

By Phillip J. Mackey, Rodney T. Jones

"Copper and copper alloys remain key materials for society today, with important uses found in the electrical, transportation, and construction industries. Copper demand is rising, with projections indicating that by 2025 global refined copper demand will increase to 29.5 million tons, up from the 22.4 million tons anticipated for 2015. This will require the opening up of dozens of new mines and numerous new smelters over this time period. Fortunately, Africa has significant reserves of copper, and African copper can once again play a key role in contributing to meeting the rising global demand for copper. This paper provides a brief overview of the current copper smelting operations in Southern Africa. INTRODUCTION Copper and copper alloys are essential materials for today’s modern world. The familiar green copper patina colour seen on buildings and other structures sometimes belies its true “green” characteristic – copper is essential for key emerging technologies such as wind turbines, tidal generating systems, solar energy systems, electric cars and the like. Consequently, it is believed that there will be continued growth in copper demand in the years ahead. Projections indicate that by 2025, as an example, global refined copper demand will increase to 29.5 million metric tons, up from the 22.4 million ton level anticipated for 2015. This will require dozens of new mines, and of the order of the equivalent of 10 to 12 new 0.5 million tons of copper/year-sized copper smelters (after factoring projected copper produced by electrowinning (EW))—overall, a huge undertaking. Fortunately, Africa has significant reserves of copper, and African copper can once again play a key role in supplying this rising global demand for copper. Africa’s share of global mined copper production was about 10% in 2014; however this will increase significantly in future if announced new projects eventuate. Southern Africa has an important role to play in this process. The present paper provides a brief overview of copper smelting in Southern Africa."

Jan 1, 2015

By E. Harris

Frithia humilis is an endangered succulent plant species. Its distribution range overlaps with the coal fields of Mpumalanga and it is therefore threatened by opencast mining activities in particular. One of the 11 known populations of F. humilis was translocated from a licensed coal mining site to three suitable receptor sites within the species? distribution range. A longterm monitoring programme was initiated to track the progress of the newly established populations. Temporal trends in population demography, size classes, and fecundity were recorded. Population numbers of size classes fluctuated annually. However, flower frequency increased over time and seedling recruitment contributed significantly to population growth. Receptor sites with similar geological conditions to the donor site had more persistent cohorts, which suggest that such sites should receive priority during the translocation of endangered edaphic specialists. This study not only confirms that a Frithia humilis population can successfully establish after a translocation, but also serves as an important baseline for future comparative purposes to gauge the long-term success of the translocation effort.

Jan 1, 2014

By M. Nyoka

Historically bauxite-based refractories have been used in applications where andalusite-based refractories could work. Bauxite-based refractories were chosen over andalusite-based refractories mainly because of the availability of low-cost Chinese bauxite and also because many furnaces were designed by international companies that cannot easily access high-quality products. Currently, the availability of low-cost bauxite is under threat as a result of high export duties and tariffs as well as restrictions on the amount of material that China allows to be exported. South Africa is a major producer of andalusite, and this guarantees stability with respect to both availability and price. Refractories based on andalusite have an added economic advantage over bauxite-based refractories in that unlike bauxite, which requires high-temperature calcination before use, andalusite is used in its raw state. This paper constitutes a literature study of the merits, both technical and economic, of using refractories based on andalusite compared to bauxite-based refractories. Keywords bauxite, andalusite, refractory, furnaces, calcination.

Aug 1, 2013

By A. Tor, M. Borowski, N. Szlazak, D. Obracaj

This article presents possibilities of reducing methane emission to the atmosphere in working mines in Jastrzebie Coal Company by means of proecological solution. They form a new approach towards the problem of rational and effective use of natural resources both in economical and environmental respect. Power and thermal energy for underground air conditioning in mining excavations are produced from the methane, which is drained out of the mine for safety reasons.

Jan 1, 2003

By Y. Mitani, F. Vallier, T. Esaki

Shear-flow coupling tests are conducted using an original apparatus, and a shear-flow coupling model using Geographic Information System (GIS) is developed in order to evaluate shear-flow coupling properties of a rock joint. Shear-flow coupling tests indicate that the hydraulic conductivity of joint once decreases, and then rapidly increases at the shear displacement near the peak shear stress. The proposed model simulates the test results relatively well. However it indicates that it is difficult to apply the local ‘cubic law’ model in the initial shear stage, in which the change of selective flow path is remarkable. Scher-Fliess-Kopplungsversuche werden mit einem neuartigen Versuchsgerät durchgeführt und mithilfe von Geo-Informationssystemen (GIS) gedeutet, um so ein Modell für die Scher-Fliess-Kopplung in Gebirgstrennflächen zu entwickeln. Die Versuche zeigen, dass die hydraulische Leitfähigkeit zuerst abnimmt, dann aber schnell wieder zunimmt sobald die maximale Scherfestigkeit erreicht ist. Das vorgestellte Modell bildet die Testergebnisse relativ gut nach. Es zeigt auch, dass es schwierig ist, das lokale Cubic Law im Initialstadium der Scherbeanspruchung anzuwenden, in dem die Variationen selektiver Fliesswege gross ist. Les essaies hydro-mécaniques couplés en cisaillement sont réalisés grâce à un appareil éxperimental prototype et un modèle de couplage hydro-mécanique utilisant le S.I.G (systeme d&apos;information géographique) développé dans le but d&apos;évaluer les propriétés hydro-mécaniques des joint rocheux. Les résultats indiquent que la conductivité hydraulique des joints décroit puis augmente rapidement en se rapprochant du pic de cisaillement. Le modèle proposé simule relativement bien les résultats expérimentaux ; mais indique également qu’il est difficile d’appliquer localement la loi cubique au début du cisaillement où, les changements d’orientation dans le réseau d&apos;écoulement sont considerables.

Jan 1, 2003

Zincor operates four Lurgi fluidized-bed roasters at its roast-leach-electrowin refinery in Springs, South Africa. In 2006, Zincor?s four roasters had reached ages ranging between 26 and 38 years, while the expected life of this type of roaster is generally 20 to 25 years. Roaster 3 was the first to be rebuilt in 2006 because its condition had deteriorated the most. Roaster 4 is being rebuilt in 2007 and the last two roasters will be rebuilt over the next few years as necessary. The main damage to Roaster 3 was caused by buckling of the roaster steel shell. This caused the freeboard and dome areas to shift, resulting in cracks in the dome brick lining and crumbling of the bricks lining the freeboard. The steel shell buckled owing to the combined effects of excessively high operating temperatures and corrosion. These were caused by the following two main factors: ?Thicker external insulation was installed during a previous maintenance shut, which resulted in an increased steel shell temperature and exacerbated the normal metal fatigue ?SO2/SO3 containing gas that had permeated the brick lining passed through its dew point during frequent planned and unplanned shuts over the life of the roaster. This caused acid formation between the refractory brick lining and steel shell, resulting in corrosion of the shell. The initial plan was to replace only the damaged areas of Roaster 3, but when it was dismantled more damage was found, and the roaster was rebuilding from the tuyeres upwards. During there building the opportunity was taken to modify the design of some of the brickwork to extend its life and make future repairs easier. This paper discusses the mode of failure of Roaster 3 and the lessons learnt during its dismantling and rebuilding.

Jan 1, 2007