Search Documents

The 108th Annual General Meeting of The South African Institute of Mining and Metallurgy was held at The Country Club, Johannesburg, Napier Road, Auckland Park on Thursday, 11 August, 2005. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations, also to recipients of awards, senior members of industry, Honorary Life Fellows, past-presidents, our members and other guests, among them the following: Dr Con Fauconnier, President, Chamber of Mines of South Africa Prof. Jay Barton, President, The Geological Society of South Africa V. Townshend, President, Institute of Certificated Mechanical and Electric Engineering, South Africa M. Livingstone-Blevins, President, Institute of Certificated Mechanical and Electrical Engineers, South Africa Prof. B. Lacquet, President, South African Institute of Electrical Engineers Dr F. Malan, President, South African National Institute of Rock Engineering

Jan 1, 2005

By O. S. L. Bruinsma, M. J. Matsela, D. J. van der Westhuizen

The free ligand (FL) model is an intuitive model to calculate the equilibrium concentrations in solvent extraction (SX) based on the distribution coefficient (Kd) at infinite dilution and the fraction of free ligand available for extraction. In this work, the FL model is validated to account for co-extraction of Ni and for designing the extraction and scrubbing sections of Co/Ni separation in a base metal refinery. Cyanex 272 is employed as a selective Co extractant in the process to yield high purity Ni. To enhance the loading capacity of the extractant, 50 mol% of NaOH is pre-loaded into it. Experimental and FL modelling results show that four equilibrium stages are required to purify the 99% Ni feed to a 99.97% Ni raffinate. The 53.59% co-extract with 26.76% free ligand is purified with a reflux scrub of 30 g Co/L in one equilibrium stage to 99.01%, Co in the scrubbed extract. The FL model as well as the Co/Ni/Na-analysis of the aqueous phase confirm that in the scrubbing section, Ni in the extract is mainly replaced by Co. Finally, in the one stage stripper the Co concentration in the scrubbed extract is increased from 5.6 g Co/L in the extract to 30.5 g Co/L that is partially used as reflux scrub liquor.

Dec 11, 2024

By J. W. Latilla, J. J. van Wijk

A running facebreak ahead of the powered support units occurred on the number 4 seam at Matla Coal’s number 3 shaft (Matla 3) in April and May 2002.Very difficult mining conditions were experienced for a distance of some 150 m in the tailgate and to a lesser extent on the face itself. The paper analyses the main causes for the high stress conditions leading to the facebreak, namely, the existence of a >20 m dolerite sill close to surface and the effect of stopping longwalling on the overlying 5 seam. Difficulties experienced during the facebreak are discussed, including, pillar and roof collapses in the tailgate, high stress areas ahead of the face causing roof and sidewall stability problems, flushing of broken rock into the face area at the tailgate, secondary mid-face breaks, and the availability of critical support units. Successful rock engineering interventions and learning points were that, a goaf angle of 14.6° was found to be more realistic than the previously used 20 to 25° in predicting dolerite sill behaviour in this area, pre-split blasting of the sill significantly reduced stress on the face and tailgate allowing re-support work to proceed, varying pillar support types were analysed and rated, the need to always have a ground control “First Aid” kit available was recognised and a strategy for subsequent panels beneath the sill was developed. Numerous support units were used and the performance of the more suitable types is briefly discussed. A running facebreak ahead of the powered support units occurred on the number 4 seam at Matla Coal’s number 3 shaft (Matla 3) in April and May 2002.Very difficult mining conditions were experienced for a distance of some 150 m in the tailgate and to a lesser extent on the face itself. The paper analyses the main causes for the high stress conditions leading to the facebreak, namely, the existence of a >20 m dolerite sill close to surface and the effect of stopping longwalling on the overlying 5 seam. Difficulties experienced during the facebreak are discussed, including, pillar and roof collapses in the tailgate, high stress areas ahead of the face causing roof and sidewall stability problems, flushing of broken rock into the face area at the tailgate, secondary mid-face breaks, and the availability of critical support units. Successful rock engineering interventions and learning points were that, a goaf angle of 14.6° was found to be more realistic than the previously used 20 to 25° in predicting dolerite sill behaviour in this area, pre-split blasting of the sill significantly reduced stress on the face and tailgate allowing re-support work to proceed, varying pillar support types were analysed and rated, the need to always have a ground control “First Aid” kit available was recognised and a strategy for subsequent panels beneath the sill was developed. Numerous support units were used and the performance of the more suitable types is briefly discussed. Une cassure de taille en avant des unités de soutènement s’est produise sur la veine numéro 4 dans le puits numéro 3 (Matla 3) de la mine Matla Coal en avril et mai 2002. Les conditions d’extraction étaient extrêmement difficiles sur une distance d’environ 150 m dans la voie de tête et, en moindre mesure, sur le front de taille lui-même. L’étude présente analyse les raison majeures pour les conditions de grandes contraintes qui ont conduit à la cassure de taille, à savoir l’existence d’un mur de dolérite de >20m proche de la surface et l’effet d’arrêter la longue taille sur la veine 5 superposée. Les difficultés rencontrées pendant la cassure de taille sont rapportées, y compris les effondrements de piliers et toit dans la voie de tête, les aires de grandes contraintes en avant du front de taille causant des problèmes de stabilité pour le toit et les parois latérales, l’injection de roches cassées dans la taille en voie de tête, les cassures secondaires à mi-taille, et la disponibilité d’unités de soutènement critiques. Interventions minières réussies et leçons apprises furent : un angle de remblai de 14.6° était plus réaliste que celui de 20 à 25° utilisé auparavant pour prédire la conduite du mur de dolérite dans cet endroit ; tir à deux temps du mur a réduit considérablement les contraintes sur la taille et la voie de tête, ce qui a permis un travail de support complémentaire ; des types variés de support de piliers furent analysés et évalués ; la nécessité d’avoir toujours une trousse de première urgence disponible fut reconnue ; et finalement une stratégie pour les panneaux en dessous du mur fut

Jan 1, 2003

By K. M. Godiwalla, S. Ranganathan

The thermal state in submerged-arc furnaces (S.A.F.) producing ferro alloys is important for the conditions of both the grade of alloy produced as well as specific energy consumption. The temperature profile in the S.A.F. is affected by the endothermic chemical reactions and the rate of gas evolution. The gas evolution commences at about 900 C due to the reduction of iron in the ore. A first-principle-based 2-D model has been developed to predict the temperature profile in the furnace. In this study, four ores of different grades have been considered in order to simulate the thermal profile in the S.A.F. The influence of the composition of the ore on the thermal profile and its significance in rationalisation of charge distribution to optimise the process are discussed.

Jan 1, 2007

By S. Lin

A new hydrogen production process, named the HyPr-RING, has been proposed. Fundamental concept of the HyPr-RING is integration of water carbon reaction, water-gas shift reaction and CO2 absorbing reaction in a single reactor. Firstly, thermodynamic analysis was done to judge the possibility to realize the process. It was found that high pressure and temperature condition, such as 20 MPa and 1000 K, is required to promote this integrated reaction. Next, experimental verification of the new process was done under the high pressure and temperature reaction conditions. As the results, integration of above three reactions in a single reactor can be done successfully and produced a large amount of hydrogen as estimated by thermodynamic analysis. Experiments showed that organic materials including coal, heavy oil, biomass, plastics can be used in this process. In the gaseous phase, no pollutants such asH2S, SO2, COS are detected so that gas cleanup system is not required for power generation when this process is used. Finally, a process design was made to estimate process efficiency. Theoretically, 1 mole of carbon can generate 2 moles of hydrogen and cold gas efficiency of this process estimated as more than 80 per cent. The process potentially reduces hydrogen production cost compared with the conventional hydrogen production methods. Keywords: Hydrogen, Fossil fuel, Energy, Process, Supercritical water

Jan 1, 2001

By T. E. Oates, W. Spiteri

In 2015, after amendments to the explosives regulations, stemming became a mandatory activity for all South African mining operations. There are, however, circumstances in which it is thought stemming has an adverse impact on the blasting outcome. Some of these circumstances include blasting in hot holes, in reactive ground, or when blasting a pre-split. In order to determine when stemming is necessary, its role in the control of adverse blasting phenomena and impact on explosive performance were reviewed. Stemming was found to play a significant role in the fragmentation process and burden movement. Additionally, stemming significantly influences the control of flyrock, air-blast, and toxic fume generation. The review of the literature indicates some motivation for not using stemming for presplit, trim, hot hole, and reactive ground blasting, provided the benefits associated with not stemming the holes outweigh the risks of stemming them. Best practice for stemming from the literature indicates a stemming length of 0.7 × burden is best for larger hole diameters, and 20 to 30 × Ø for smaller hole diameters. Crushed aggregate appears to be the most effective stemming material. The South African explosives regulations pertaining to stemming were found to be consistent with those of Australia and the USA.

Aug 1, 2021

By D. Marcotte, R. V. Dutaut

In most exploration or mining grade data-sets, the presence of outliers or extreme values represents a significant challenge to mineral resource estimators. The most common practice is to cap the extreme values at a predefined level. A new capping approach is presented that uses QA/QC coarse duplicate data correlation to predict the real data coefficient of variation (i.e., error-free CV). The cap grade is determined such that the capped data has a CV equal to the predicted CV. The robustness of the approach with regard to original core assay length decisions, departure from lognormality, and capping before or after compositing is assessed using simulated data-sets. Real case studies of gold and nickel deposits are used to compare the proposed approach to the methods most widely used in industry. The new approach is simple and objective. It provides a cap grade that is determined automatically, based on predicted CV, and takes into account the quality of the assay procedure as determined by coarse duplicates correlation.

May 1, 2021

By X. Pan

Slag-metal equilibrium experiments were conducted at 1500ºC and 1580ºC under 0.03 atm, 0.05atm and 0.83 atm CO partial pressures using silica and Cr-oxide crucibles. The complex slags belonged to SiO2-CaO-Al2O3-MgO-FeOx-CrOxand the metal phase to the Cr-Fe-C-Si-(S)systems. The carbon saturation of the metal phase was avoided using oxide crucibles and thus the results are pertinent to ferrochromium refining slags and processes. From equilibrium data and thermodynamic calculations the CrO /(CrO+Cr2O3) ratio in the slag was determined as 0.75, 0.80and 0.86 under 0.83 atm and 0.05 atm of CO pressure at 1500ºC and 0.03 atm and CO pressure at1580ºC respectively. The results clearly demonstrated that a higher chromium content of the metal results in higher Cr in the slag, and chromium in slag decreases with increasing SiO2. The results were also sensitive to the crucibles used as these oxide crucibles saturated the slag either with respect to SiO2or Cr-oxides. It was also demonstrated that the relative amount of CrO in the slag was higher when SiO2crucibles were used in accord with thermodynamic calculations. Iso-concentration curves for carbon and chromium of the metal phase in equilibrium with the slag were drawn on pseudo ternary SiO2–(AI2O3+CaO+MgO)–(Cr2O3+Fe2O3) diagram. The activity coefficients and activities of carbon and chromium of the metal phase were also calculated from the experimental data and available thermodynamics information and were plotted as iso-activity curves in the same pseudo ternary diagram. Keywords: Chromium, slag, equilibrium

Jan 1, 2004

By J. P. Germiquet

"Rock properties have a material impact on mining processes, including drilling performance. An investigation using point loaded index (PLI) data converted to uniaxial compressive strength (UCS) has revealed that a direct relationship between grain size and UCS exists at Mogalakwena Mine. This correlation is best seen in unaltered rock, with lower correlations for altered rock types. Measurements from the new RockMa system installed on drill rigs can be used to obtain rock strength data to validate the current rock strength domains and create additional data for the next benches below. An investigation of penetration rates in different lithologies shows that rock composition plays an important role in determining drill performance. Additionally, there is an inverse relationship between rock strength and drilling penetration rate – a measure of how efficiently a hole is drilled.The domaining of grain-size-adjusted UCS at Mogalakwena Mine will allow more accurate scheduling of drill rigs through increased knowledge of rock strength in various areas. Successful rock strength domaining has the potential to be incorporated into blast indexing and predicting crushing/milling performance.IntroductionThe optimization of mining and processing through geometallurgical characterization of ore are key drivers of value realization (Deutch, 2013). Rock strength is one such property and is affected by, among other variables, composition, texture, and grain size (Ozturk, Nasuf, and Kahraman, 2014). Mogalakwena Mine is exploiting the intrusive Platreef PGE (platinum group element)-bearing orebody which forms part of the northern limb of the Bushveld Complex. This complex orebody exhibits areas of metasomatic alteration, metamorphism, and sporadic mineralization of the footwall and hangingwall (Nex et al., 2006). Understanding this variability is paramount due to the implications for rock strength and hardness, which in turn affect crushing, milling, and liberation efficiency. These variables must be known prior to blasting in order to optimize mine and plant processes using in-situ variables. This necessitates predictive modelling (Deutch, 2013). Geological and geotechnical data was sourced from the Overysel (OY) exploration database for the study. Point load testing was done for each borehole and the results converted to uniaxial compressive strength (UCS) (Akram and Bakar, 2007). The relationship of lithology, texture, and grain size with UCS revealed an inverse relationship between grain size and UCS in unaltered rock. The relationship was not present in altered rock types. A comparison of mean strength and hardness results indicated that Bond work index and UCS may be related. Drilling performance is affected by UCS (Bourgoyne et al., 1986), and this was proven using recent measurements obtained during drilling. Lastly, grain-sizeadjusted UCS values were applied to a 3D model for the OY property."

Jan 1, 2016

By Chris Ringas

The safe operation of gas transmission pipelines is increasingly coming under the spotlight. Increasing environmental pressure is also forcing pipeline owners and operators to ensure the integrity of their pipelines. The integrity of a pipeline is usually determined using intelligent pigging, often referred to as In Line Inspection (ILI). However, in many cases, gas pipelines cannot be pigged for a variety of reasons. The National Association of Corrosion Engineers (NACE) has recently published Recommended Practice (RP) 0502, referred to as the External Corrosion Direct Assessment (ECDA) Methodology to assist pipeline owners with assessing the condition of pipelines that cannot be pigged. 2. External Corrosion Direct Assessment - NACE RP 0502 The ECDA Methodology is conducted in four phases as follows: ? Pre-Assessment ? Indirect Inspection ? Direct Examination ? Post-Assessment In the Pre-Assessment Phase, all the relevant historical and current data relating to the pipeline in question is reviewed. This covers pipeline, construction, soils/environmental, corrosion control and operational data. The aim of the Pre-Assessment Phase is to determine whether ECDA is feasible, and if so, to define the ECDA Regions and finally to select the Indirect Inspection Tools that will be used for each region. Typical overline techniques used for overline surveys include the following: Voltage gradient surveys ? DCVG or ACVG

Jan 1, 2006

By H. J. Uananisa, M. J. Papo, C. W. Siyasiya, W. E. Stumpf

"SynopsisThe need to reduce weight while maintaining good mechanical properties in materials used in the automotive industry has over the years seen an increased exploitation of various steels to meet this new demand. In line with this development, the ferritic stainless steel family has seen a wide application in this industry, with the AISI 436 type increasingly being used for automotive trims and mufflers for exhaust systems, as well as a significant part of this steel’s application being for the manufacture of wheel nuts and wheel nut caps in trucks, mainly through the deep drawing process. However, there have been reports of some poor surface roughening of this material during deep drawing, with tearing and/or cracking also reported in some instances. This has been suspected to possibly be associated with some local differences in localized mechanical properties between grains and grain clusters of the rolled and annealed material.In order to investigate the poor surface roughness exhibited by AISI 436 ferritic stainless steel (FSS) during deep-drawing, Lankford values (R-mean and ?r), grain size, and microtextures of various sheet samples from this steel were studied. The chemical composition range for the samples was 0.013–0.017% C, 17–17.4% Cr, 0.9–1% Mo, and 0.4–0.5% Nb. The steels were subjected to various hot and cold rolling processing routes i.e. involving industrial direct rolling (DR) or intermediate annealing rolling (IR), and the drawability and final surface qualities of the steels were compared. It was found that the DR route gave an average R-mean and ?r value of 1.9 and -1.4 respectively, while the IR route yielded an average Rmean and ?r value of 1.6 and 0.52 respectively. The high ?r value for the DR processing route had a substantial adverse effect on the drawability. IR samples exhibited a smoother surface finish on visual inspection, while clear flow lines were visible on the DR samples, despite the fact that DR is the preferred industrial processing route due to the reduced production costs it offers. This observation was also confirmed through SEM examinations. The difference in the surface quality was attributed to microtexture. However, the mechanism responsible for this difference still needs to be identified."

Jan 1, 2015

Rock engineering has now been practised as a discipline for about50 years, and many sophisticated methods of analysis for use in rock engineering design have been developed. However, analysis is only a tool for use in engineering design, and rock masses are often so complex that realistic modelling of them, even with sophisticated methods of analysis, is impossible. At the other end of the scale, rock mass classification methods have been developed to quantify the rock mass. These ?numbers? are now widely used for assessment of stability of underground and surface excavations in rock, for the determination of rock support requirements, and for the estimation of rock mass strength and deformation properties. In considering these areas, the two concepts?design, and prediction of behaviour?will be dealt with. The discussion will be introduced by a consideration of the characteristics of the rock mass, which will highlight the variability in its properties and hence the uncertainty in the behavioural parameters. Examples of real projects will be used to illustrate the discussion.

Jan 1, 2003

With the advent of the First World Conference on Sampling and Blending (WCSB1) in Denmark in 2003 and the subsequent biannual meetings, together with other sampling conferences held on a regular basis, the central tenets of sound sampling practice and theory are spreading throughout the minerals industry. End-users and project houses, or groups who execute the projects, are all now better-informed about the principles of ?correct? sampling and preparation. To support this, many large mining companies now have their own in-house champion who will advise and ensure that the supply of sampling equipment is correct in terms of design and application, which further contributes to improved metallurgical accounting. The presence of a sampling champion also ensures that consistent and acceptable standards in regard to sampling practice are maintained throughout the group. This has, in turn, placed a greater degree of responsibility on the shoulders of sampling equipment suppliers, in terms of their equipment designs and product offerings, as well as applications knowledge for effective installation of equipment on client plants. This paper attempts to highlight the significant challenges that sampling equipment manufacturers often face with regard to complying with the newly understood requirements of best practice and sampling equipment design. Manufacturers invariably face issues with end-users or project houses, including project cost control, restricted headroom for samplers in plant layouts, and a lack of knowledge in certain quarters. These all have a potentially negative effect on the final outcome of a proposed sampling solution or implemented project. In reality, what is intended by all parties and what is ultimately installed are at times very different, with undesirable consequences for all concerned. Against this challenging background, there are, however, a number of instances where intent and implementation are complementary, with very satisfactory results. Keywords sampling, mechanical samplers, design, installation, sampling theory.

Jan 1, 2014

By J. West

For many years line-of-sight (LOS) issues for underground mobile equipment is a growing focus of research. This research is a result of the numerous fatalities and injuries which occur in the mining industry and which are related to poor operator LOS. Three assessment methods are currently used to assess operator LOS of underground mobile equipment. The light filament (LF) method is a hands-on assessment method that is performed in the field. This method is not evaluated in this paper. The laser scan (LS) method of assessing equipment is a quick and reliable method that comes from the need to evaluate vehicles already located in the field. The computer simulation (CS) method can assess LOS issues using a computer aided drawing (CAD) model, which is useful for assessing current or prototype models. The purpose of the current research is to compare and validate different operator LOS assessment methods. Comparison of the results of the LS and CS visibility plots yielded similar quantifiable results. A visual comparison of the results further illustrate that the LS and CS methods are acceptable assessment tools for mobile equipment operator LOS evaluation. The visibility assessment methods are now being prepared as guidelines for the mining industry to assess current and potential designs.

Jan 1, 2007

By J. West

For many years line-of-sight (LOS) issues for underground mobile equipment is a growing focus of research. This research is a result of the numerous fatalities and injuries which occur in the mining industry and which are related to poor operator LOS. Three assessment methods are currently used to assess operator LOS of underground mobile equipment. The light filament (LF) method is a hands-on assessment method that is performed in the field. This method is not evaluated in this paper. The laser scan (LS) method of assessing equipment is a quick and reliable method that comes from the need to evaluate vehicles already located in the field. The computer simulation (CS) method can assess LOS issues using a computer aided drawing (CAD) model, which is useful for assessing current or prototype models. The purpose of the current research is to compare and validate different operator LOS assessment methods. Comparison of the results of the LS and CS visibility plots yielded similar quantifiable results. A visual comparison of the results further illustrate that the LS and CS methods are acceptable assessment tools for mobile equipment operator LOS evaluation. The visibility assessment methods are now being prepared as guidelines for the mining industry to assess current and potential designs.

Jan 1, 2007

By W. Newcomen, G. Dick

"Effective management and mitigation of pit slope instability in open pit mines begins with a comprehensive slope monitoring programme. The ability to differentiate between non-critical pit wall movements due to rebound or relaxation of the excavated slopes and movements that may be indicative of slope failure is important for maintaining a safe working environment and maximizing production. Slope failure prediction methods using velocity, acceleration, and strain criteria have been introduced and put into practice over the past few decades. Forty-eight slope failures with surface monitoring data are presented and assessed using the strain-based failure prediction approach, with consideration of the quality of the rock mass and the potential failure mechanism. The results indicate that the strain-based approach can be used to provide general guidance regarding strain thresholds for pit walls for a variety of failure modes in diverse geological environments. The advantages and potential drawbacks of the strain-based and other slope failure prediction methods are discussed. The importance of implementing a pit slope monitoring and performance evaluation system early in mine development is also emphasized. IntroductionThe successful prediction of the Manefay Slide pit slope failure at Bingham Canyon at 9:30 am on 10 April 2013 (Engineering and Mining Journal, 2014) highlighted the importance of having a comprehensive slope monitoring system that provides an accurate prediction of the time of failure of an open pit slope. Using most of the geotechnical monitoring tools available, the time of the failure was predicted within hours and equipment and personnel were evacuated from the pit well in advance of the failure. From a time to slope failure perspective, the monitoring system in place was a success.There are two general groups interested in monitoring pit walls, with slightly different objectives in mind when the monitoring system is being set up. There are those at the mine site that have to implement the pit slope design, monitoring protocols, and the action response plans, and there are those designing the slopes (often consultants) who regularly visit the mine but may not be responsible for the day-to-day activities. was a success.There are two general groups interested in monitoring pit walls, with slightly different objectives in mind when the monitoring system is being set up. There are those at the mine site that have to implement the pit slope design, monitoring protocols, and the action response plans, and there are those designing the slopes (often consultants) who regularly visit the mine but may not be responsible for the day-to-day activities."

Jan 1, 2016

By D. Whittles, C. J. Lea, T. X. Ren, A. Kelsey

A methodology for the simulation of methane drainage combining geotechnical modelling and computational fluid dynamics (CFD) will be described. Geotechnical modelling was used to predict the development of stress and strain due to mining. The results from the geotechnical modelling were combined with empirical expressions for the variation in permeability with stress of coal measure rocks and assumptions on fracture behaviour. This allowed the permeability, as affected by mining, to be specified in CFD simulations. Flow of methane through strata, with and without methane drainage, was then simulated to examine the effects of methane drainage.

Jan 1, 2003

By D. Vogt, T. Hattingh

"This paper argues that the technology change to mechanization is also going to require a change in people. It presents a model for technological progress and adapts it to the mining industry. It then goes on to motivate the need for mines to become learning organizations in order to achieve maximum value from their people as they become less labour-intensive. In an important sense, mechanization is as much about knowledge as it is about technology.The change when a mine introduces mechanization or a level of automation is not simply one of technology but also a stage in the development of mining from ‘art’ to ‘science’. ‘Art’ describes a state of technology characterized by tacit knowledge, an understanding that comes only from experience, and has no formal procedures and little structure. In contrast, ‘science’ represents a state of technology where all the component processes are understood in detail, all knowledge is explicit, and processes and structures are formal.Studies of other industries, including metal part manufacture and aviation, show that each stage in the progression from art to science changes the nature of the organization and requires a different mix of skills from the workforce. Perhaps the most important change is the increase in knowledge and decision-making required as the technology gets closer to science.There is anecdotal evidence that South African underground hard-rock mines are not learning organizations. Mines by their nature are capitalintensive with long lead times from investment to returns, so there is reluctance to change from the original plans or to encourage staff to think independently. Particularly as mines move from art to science, this reluctance must be overcome.The important lesson for engineers involved in introducing mechanization is to understand that success or failure will be determined by the people involved, and not solely by the technology. The process will almost certainly require a culture change on the mine. We recommend that the mechanization team includes an expert in human and organizational behaviour to ensure that a receptive workforce and management are in place to accept the new technology when it arrives."

Jan 1, 2016

By X. M. Prévost

The reassessment of coal reserves has become a matter of urgency and has come as a result of the present situation of the industry, in the context of globalized coal economies, as well as new mining legislation and the advantages and difficulties of domestic coal suppliers. The de Jager report concerning coal reserves, released twenty years ago, can no longer be used as an estimate for accurately forecasting South Africa’s future coal production. The new reserve and resource study will promote the diversification of energy sources and provide a clearer view of the future of coal mining in the country. With plans to increase South Africa’s coal export capacity to approximately 84 million tons by 2005, it is uncertain whether the country really has sufficient reserves to meet this expansion, as well as satisfy the projected increase in inland demand. The face of South Africa’s coal industry and by association, the economy of our coal-dependent country, are both set to change. This is mainly due to factors such as the demise of most of the large collieries over the last approximately twenty years, growing numbers of economic empowerment producers, the emergence of strong competition in the export market, the dawn of Clean Coal Technologies (CCTs) and the Kyoto Protocol The paper will attempt to dispel some of the current myths about coalfields and reserves and highlight potential areas of high quality coal reserves, available mainly to new entrants in the industry. Keywords: Central Basin, Clean coal technologies, Coal combustion, Coal exports, Coalfields, coalLink, Coal reserves, Coal resources, Coal processing, Colliery, Economic empowerment, Discards, Fluidized bed combustion, Low-ash coal, Metallurgical coal, Power generation, Pulverized fuel, Reserve blocks, Richards Bay Coal Terminal, Run-of-mine production, Saleable production, SAMREC Code, South Dunes Coal Terminal, Steam coal, Synthetic fuels.

Jan 1, 2003