Search Documents

By A. D. Thomas

Some years ago, the authors developed an analysis of non-Newtonian pipe flow based on enhanced turbulent microscale and associated sublayer thickening. This analysis, which can be used for various rheologic modelling equations, has in the past been applied to smooth-walled pipes. The present paper extends the analysis to rough walls, using the popular Bingham plastic equation as a representative rheological behaviour in order to prepare friction-factor plots for comparison with measured results. The conditions for laminar-turbulent transition for both smooth and rough walls are also considered, and comparisons are made with earlier correlations and with experimental data.

Jan 1, 2007

By N. Barton, E. Quadros

This paper addresses the prediction of groutable joint apertures, grout penetration limitations, and possible grout take volumes per cubic metre of rock, as a result of 5 to 10 MPa pre-injection pressures ahead of tunnels. Joints are obviously opened more than in the preceding Lugeon tests, and many rock mass properties can apparently be improved if stable micro-cement based materials are used. Cet article concerne la prédiction des ouvertures des fractures injectables, les limites de pénétration du coulis et les volumes injectés par mètre cube, d’après les résultats des injections à l’avant tête des tunnels sous pressions de 5 à 10 MPa. Evidemment les joints s’ouvrent plus que dans les essais Lugeon précédents. Maintes propriétés du massif peuvent apparemment être améliorés si l’on emploi des coulis a base de micro-ciment stable. Die Publikation widmet sich der Prognose injizierbarer Kluftöffnungen, Grenzwerte für Injektionsreichweiten und erreichbarer Injektionsvolumen pro Kubikmeter injizierter Fels, durch die Anwendung von 5 bis 10 MPa Vorinjektionsdrücken vor der Tunnelfront.Die Klüfte werden offensichtlich weiter geöffnet als in den vorhergegangenen Lugeon Versuchen und mehrere Felsparameter können durch die Verwendung von stabilisierten Micro-Zement basierten Injektionsmaterialien verbessert werden.

Jan 1, 2003

By P. Malíková, I. Osičková, R. Sousedíková, P. Rys, J. Dvořáček, S. Heviánková

Each mining project goes through the same life-cycle, from prospecting and exploration to closure and post-closure periods. This prompts the question whether the closure of a mine constitutes the end of its life-cycle or whether the decommissioned mine can be employed for some other purpose. Best-practice references indicate that there are many viable options. In our opinion, the production of service water is one such option. Laboratory research was carried out on the water from a flooded underground coal mine in Ostrava- Karviná coal district, Czech Republic, concerning the production of service water from pumped minewater. The research proved the practical feasibility of service or process water production. Given the effect of global climate change with regard to water resources, good prospects for this additional resource can be assumed since the water has to be pumped in any case for safety reasons.

Oct 1, 2022

By H. Jang, Y. Kawamura

Unplanned dilution and ore loss directly influence not only the productivity of underground stopes, but also the profitability of the entire mining process. Stope dilution is a result of complex interactions between a number of factors, and cannot be predicted prior to mining. In this study, unplanned dilution and ore loss prediction models were established using multiple linear and nonlinear regression analysis (MLRA and MNRA), as well as an artificial neural network (ANN) method based on 1067 datasets with ten causative factors from three underground longhole stoping mines in Western Australia. Models were established for individual mines, as well as a general model that includes all of the mine data-sets. The correlation coefficient (R) was used to evaluate the methods, and the values for MLRA, MNRA, and ANN compared with the general model were 0.419, 0.438, and 0.719, respectively. Considering that the current unplanned dilution and ore loss prediction for the mines investigated yielded an R of 0.088, the ANN model results are noteworthy. The proposed ANN model can be used directly as a practical tool to predict unplanned dilution and ore loss in mines, which will not only enhance productivity, but will also be beneficial for stope planning and design.

Jan 1, 2015

By L. Arnberg, E. Ott

The microstructure of ferrosilicon is important since it controls the disintegration of the material during crushing and thus the generation of fines. Therefore a study of the microstructure formation during solidification of pure FeSi(75wt%Si) and FeSi(75wt%Si) containing 1.2wt%Al and 0.2wt%Ca has been initiated. The material has been cast into rods of 8mm diameter, which have been remolten by induction heating and directionally solidified in a Bridgman apparatus. This allows the temperature gradient and the growth rate to be controlled independently. The temperature history during solidification has been recorded by a thermocouple in the melt. Growth rates have been varied between 5 and 400µms-1 and temperature gradients between 3 and 14°Kmm-1. The microstructures show a large dependence on the solidification conditions. The crack formation in the alloys has been studied and found to be strongly related to the microstructure.

Jan 1, 2004

By M. Tangstad, D. Lu, G. Tranell, S. Gaal, J. Safarian

The kinetics of MnO reduction from high carbon ferromanganese slag was investigated using a sessile drop technique at 1600 ºC. The effects of reductant type, ambient atmosphere and slag composition on the MnO reduction were illuminated. Two different types of industrial reductants (ground to a particle size of 44 to 106micron and pressed to pellets) were used as substrates for small slag droplets of varying composition, which were reacted in a CO or Ar atmosphere with the reaction studied in-situ. The cross sections of the reacted slag-carbon samples were subsequently studied by EPMA to find the extent of MnO reduction as a function of reaction time. It was found that the rate of MnO reduction is affected by both the type of reductant, the ambient atmosphere and the presence of metallic components in the slag. Higher reduction rates were obtained for charcoal than for coke as reductant while a CO atmosphere unexpectedly yielded faster MnO reduction than an Ar atmosphere. It was also found that metal prills in the initial slag will increase the rate ofMnO reduction.

Jan 1, 2007

By S. S. Makgato

In this study, coke oven tar additions over a range of 0?8 wt.% were evaluated as a possible substitute for imported coal fractions. The coke oven tar used was collected from tar decanters in the byproducts section of the coking plant. The moisture content in the tar varied depending on the residence time and water carryover from the coke oven tar separators to the storage tanks. Moisture contents of 1 wt.%, 3 wt.%, and 6 wt.% were investigated in order to evaluate the effect on coal blend, carbonization, and coke properties. At 6 wt.% moisture content with 6 wt.% coke oven tar, although the coke quality improved the yield showed a 4% decrease. On the other hand, 1 wt.% moisture content with coke oven tar of 6 wt.%, increased the yield by 1% and the coke quality improved. However, the latter process was characterized by an excessive increase in wall pressure and pushing energy, both of which are detrimental to the oven walls. The optimum moisture content in coke oven tar was found to be 3 wt.% with a coke oven tar addition of 6 wt.% in the coal blend. With these conditions, the coke properties improved and wall pressure and pushing energy were acceptable. However, a decrease in coke yield of up to 2% was observed. Despite this, coke oven tar addition is considered to be a viable option based upon economic factors of a reduction in the quantity and cost of imported coking coals that is required to achieve the same optimum final coke product. Keywords coal substitution, coke oven tar, tar moisture, coal blend, coke, coke quality.

Nov 1, 2013

By M. A. van Nierop

Load behaviour in an industrial mill has been measured directly by inserting probes through liner bolts. The data from conductivity probes have indicated the presence of premature centrifuging during manipulation of the load mass. Overloading conditions were also encountered. Overloading and premature centrifuging both reduce the power drawn by the mill. These effects have been successfully modelled.

Jan 1, 1997

By D. Tsweleng

In the Evraz Highveld production process, iron ore is prereduced in rotary kilns prior to charging into submerged arc furnaces (SAFs). Owing to the highly aggressive slags that are formed within the combustion zones of these kilns, chrome-oxide-containing lowcement castables have been used for some years in the kiln lining. Due to concerns around the potentially harmful effects should Cr(V1) be present in the spent linings, Highveld and its suppliers of kiln castables devoted time to developing alternative chrome-free lining materials. Such materials needed to be cost-effective and ensure good performance and improved kiln availability. This paper discusses all the parameters surrounding this development. Keywords Low-cement castable, chrome-oxide free, chrome (VI), titaniferous magnetite ore, rotary kiln, submerged arc furnace, open slag bath furnace, Evraz Highveld Steel & Vanadium Limited.

Aug 1, 2013

By L. Andrews

Keywords: mineralogy, phase-chemical, chemical-looping combustion, XRD, SEM, EDS, QEMSCAN, PGM, slag, matte, ilmenite Mineralogy, traditionally associated with concentrator studies, is being increasingly applied to problems in pyrometallurgy. Such investigations commonly make use of a number of techniques, and the results are combined for a meaningful interpretation, which can lead to a successful solution. Mineralogical applications are described from pyrometallurgical operations. Examples are given of studies and investigations involving mineralogy in chemical-looping combustion, feed monitoring to platinum-smelting furnaces, and losses to slag in base metal and platinum smelting.

Jan 1, 2011

By G. Song

"SynopsisAccording to the overlying rock strength and thickness of 10 shallow coal seams in China, the strata are classified into four types: weak and laminated strata (hereinafter referred to as WL), weak and massive strata (WM), strong and laminated strata (SL), and strong and massive strata (SM). The four types of strata, together with longwall panel height (M), panel length (L), and seam depth (H) are factors that influence the loads on hydraulic power supports. Principal component analysis was used to study the seven influencing factors. It turns out that seam depth (H) is multicollinear with WL, WM, SL, and SM. Thus the enumerated seven factors are divided into two models. In Model 1, six factors; panel height, panel length, and layer thickness of the four type strata are involved. In Model 2, three factors; panel height, panel length, and seam depth are included. Using multivariate regression analysis, two equations to calculate loads on supports are obtained for each model. The equations were applied to shallow coal seams. The equation of Model 1 is more accurate than that of Model 2, but Model 2 could be further used in deep coal seams. The equations were coded through VB programming to simplify the calculation.IntroductionTo ensure coal production in the long term, the focus of coal mining has been gradually shifted to the western areas of China in recent years due to rich coal resources in this region. Most of the coal seams in this area are shallow but the support loads are abnormally high. In these circumstances, the chock loads estimating methods used in the past do not work. If the rated working resistance of a support is larger than needed, the shield is unable to fully perform, while a lower working resistance would lead to accidents like shield crushing or even casualties. This problem is frequently found in shallow coal seams such as Shenfu-Dongsheng, Yulin, Tuha, Lingwu etc. (Zhang, 2011). Thus, to ensure safety and efficiency during mining, the estimation of support loads and selection of supports are of great significance."

Jan 1, 2015

By Jeremy Bosman, Johan de Korte

Traditionally the feed to coal preparation plants was de-slimed at 0,5 mm. The +0,5 mm size fraction was processed via dense-medium cyclones and the -0,5 mm size fraction was beneficiated with froth flotation, water-only cyclones or spirals. With the introduction of large diameter cyclones, the aperture sizes of de-sliming screens have progressively increased to about 3 mm in the belief that the larger cyclones are not able to effectively beneficiate coal which has a particle size below the ?breakaway? size. The efficiency of separation in the large dense-medium cyclones is improved by presenting a coarser feed to the units. At the same time, the capacity of the de-sliming screens is increased due to the larger screen apertures and in effect, the throughput capacity of the dense-medium section is increased. The 3 x 0,5 mm size fraction, which was previously processed in the dense-medium cyclones, is now added to the fine coal size fraction and processed by water-only methods such as Teetered Bed Separators (TBS) and spirals. Whether this practice is the most economical way to process the 3 x 0,5 mm size fraction requires further thought since the best processing route for the 3 x 0,5 mm size fraction will depend on a number of factors, amongst which are: o The washability of the coal and the amount of near-density material o Processing efficiency o Specification of the required product o The price paid by the customer for the product o The cost of processing the coal Breakaway size The ?breakaway? size is defined as the particle size below which the Epm of the smaller particles starts to decrease significantly. Bosman1 provides an approximate breakaway size versus cyclone diameter (Figure 1). It should be kept in mind though that the Epm of the small particles is a function not only of the cyclone diameter but also of feed pressure, medium density, medium viscosity, particle shape and density, top-size of particles in the feed, etc.

Jan 1, 2006

By H. A. Bilgin, A. Özgenog?lu, G. Kaçar

In this study, the influences of rock mass properties on the blasting performance in open cast mines are investigated. To this end, discontinuity spacings and discontinuity orientations are measured and full scale blasts with various designs are observed in open cast mines of Aegean Lignite (ELI) and Bursa Lignite (BLI) Establishments belonging to Turkish Coal Enterprises (TKI). For each blast, blasting cost is calculated, and particle size distribution representing the fragmentation of muckpile is determined by means of Split-Desktop software using image processing. 50%(K50), 80%(K80) passing sizes and topsize values are used in the determination of blasting performance according to rock mass properties. The relationships between orientation angle, which is the acute angle between the strikes of slope face and major discontinuity, and 50%(K50) and 80%(K80) passing sizes and topsize values and also blasting cost are investigated in order to analyse the influences of major discontinuity orientation on fragmentation and blasting cost. Furthermore, the relationships between discontinuity modal spacing (or block size index) and 50%(K50) and 80%(K80) passing sizes and topsize values and also blasting cost are investigated in order to analyse the influences of discontinuity spacing on fragmentation and blasting cost. In this paper, the trends observed in these relationships are discussed and the importance of it in mining is commented. Dans ce travail, Il a été traite les influences des qualites des rocheux massif sur les performances des abattages de l’excavation a ciel ouvert. Dans ce cas, les excavations a ciel ouvert dans les Entreprises Lignite d’Aegean et de Bursa qui appartient a La Societe Charbon de la Turquie; Il a été mesuré le trou du discontinuite et l’orientation du discontinuite et aussi, Il a été observé les abattages qui sont pareilles aux critaires exactes. Pour chaque abattages, Il a été fait le control des expences et la distribution du particle au dimension du pile qui a été deja abatté, a été trouve en utilisant le Software du Split-Desktop. Pour determiner les influences des qualites des rocheux massif sur les performances des abattages, Il a été utilisé K50, K80, et le plus grand valeurs des dimensions. Aussi pour determiner l’influence sur l’orientation du discontinuite majeur de la fragmentation et les expences de l’abattage, Il a été observé les relations entre l’angle de l’orientation ( C’est l’acutage entre la direction du banquette front et la direction du discontinuite majeur ) et les plus grand valeurs des dimensions et les expences de l’abattage. Plus, pour determiner des influences du trou du discontinuite sur l’abattage et la fragmentation; Il a été observé la relation entre l’index de la dimension du block et K50, K80 et les plus grand valeurs des dimensions et aussi les expences de l’abattage. Pour conclure; on peut dire que dans cette presentation, apres la discusssion des sujets consideres ces relations, Il a été souligné l’importances de ces relations dans la domain de la Minéralogie. In dieser Studie wurden die Einflüsse von Gesteinsmasse Eigenschaften auf die Sprengleistung in Tagebau Bergwerken untersucht. Zu diesem Zweck wurden Diskontinuität Abstände und Diskontinuität Orientierungen gemessen und Sprengungen im Originalmaßstab mit verschiedenen Anordnungen in Tagebau Bergwerken der Ägäischen Braunkohle (ELI) und Bursa Braunkohle (BLI) Betrieben, die zu der Türkischen Kohlegesellschaft (TKI) zugehörig sind, beobachtet. Für jede Sprengung wurden die Sprengkosten berechnet und die Teilchengrößenverteilung zur Darstellung der Aufteilung von Haufwerk ist durch Mittel von Teilbelegungssoftware, das Bildverarbeitung verwendet, bestimmt worden. 50% (K50), 80% (K80) durchlaufende Größen und Spitzengröße Werte wurden zur Bestimmung von Sprengleistung geordnet nach Gesteinsmasse Eigenschaften benutzt. Die Beziehungen zwischen Orientierungswinkel, welches der scharfe Winkel zwischen den Streichen der Hangfläche und Hauptdiskontinuität ist, und 50% (K50) und 80% (K80) durchlaufende Größen und Spitzengröße Werte sowie Sprengkosten wurden untersucht, um die Einflüsse von Hauptdiskontinuität Orientierung auf Aufteilung und Sprengkosten zu analysieren. Außerdem, wurden die Beziehungen zwischen Diskontinuität modal

Jan 1, 2003

By E. Demir

Transportation cost is the dominant cost and accounts for almost half of the total mining cost in surface mining. Therefore, determining transportation cost is critically important for the economic feasibility of mining projects. Turkey produces around 85 million tons of lignite per annum. The biggest state-owned company, Turkish Coal Enterprises (TKI), accounts for 43 per cent of the country?s total lignite production. Around 85 per cent of the produced lignite is used in power plants for electricity generation and 15 per cent is used for domestic heating in cities and urban areas. On behalf of the Turkish government, TKI distributes around 2 Mt of lignite annually, at no cost to poor needy families countrywide in accordance with Social Assistance and Solidarity Funding aid. Subcontractors are utilized for lignite transportation, and conflicts arise due to the different transportation cost calculations at different mines. A robust model that provides unbiased cost estimations is therefore of paramount importance. This paper presents the transportation cost estimation software, NAKMAL, that has been developed for estimating the transportation cost of lignite from the mine face, including excavation and loading, to various final destination points through five different transportation scenarios. NAKMAL was designed using VisualStudio.NET, validated using field data and some case studies, and it is currently being used by TKI for calculation of transportation cost country-wide.

Jan 1, 2012

By S. Matsuyama, S. Tomita, H. Kawahara, G. Deguchi

A proper management system of coal mine methane gas associated with underground mining activities is essential for the mine safety due to its nature of explosion. Optimum design of the mine ventilation and gas drainage need accurate prediction of gas flow rate emitted by mining activities. Permeability to gas, which is affected by stress conditions of surrounding rock mass, governs the emission rate of the gases. JCOAL has developed a three dimensional FEM simulation program named Mine Gas Flow 3D (MGF-3D). MGF-3D is designed to predict the volume of methane gas emitted from surrounding coal and rock seams based on stress distribution and permeability change which are determined by 3D stress analysis. In MGF-3D, stress change and/or expansion of fractured zone affected by mining is calculated at the first and then gas emission into roadways and longwall panels under the determined stress conditions is calculated using Darcy’s law. MGF-3D also can set up a number of pre-drainage holes and estimate drainage gas volume from each hole. This function makes MGF-3D remarkable program. These simulations for gas emission can contribute to mine gas utilization plan. Comparison between actual measurement of gas emission in the underground mine and simulation results has been performed and availability for the mine safety and problems with MGF-3D are discussed in this report.

Jan 1, 2003

By J. F. Reddick

The South African coal mining industry is currently disposing of about 10 million tons of ultra-fine coal (<150 µm) per year. Once discarded, these sulphur-containing ultra-fines contribute to several environmental problems. As part of a project initiated by the Water Research Commission to investigate the use of Cleaner Production (CP) in the mining industry, a study was carried out to determine whether a CP approach could be used to identify opportunities to reduce this coal waste, and to determine which of these opportunities would be most feasible. In order to do this, a CP assessment was conducted at three case study collieries in the South African Witbank coalfield. Mass-balancing and sampling, followed by laboratory characterisation tests and site surveys, were used to determine the quantity, quality and sources of the ultra-fine coal at the three collieries. Literature reviews, brainstorming sessions and interviews then followed to generate the CP options. An environ-mental, economic and technical feasibility assessment was then prepared for each option, to determine the most viable interventions for implementation. A number of opportunities were identified through the assessment. By preventing coarser coal from being discarded with the ultra-fine coal, the quantity of coal disposed of could be decreased at all three collieries, and by up to 24% in one case. Increasing the crusher top size would reduce the amount of coal that is milled to less than 150 µm, so that less is wasted. The ultra-fines that have already been disposed of on slurry dams can be completely reclaimed and converted into a valuable product, which can be sold as power station feedstock. The newly processed ultra-fines could be beneficiated using flotation and exported together with the coarser coal. The results of the assessments thus suggested that workable CP opportunities to reduce ultra-fine coal wastage exist at the sites investigated, and that their feasibility is colliery-specific. The associated financial benefits of the proposed options suggested that CP is a realistic approach to addressing environmental problems. Keywords: Cleaner Production; coal mining; coal-washing; ultra-fines

Jan 1, 2007

By I T. Tshabalala

In typical conventional narrow vein stoping operations, the use of temporary support components to offer some support to workers, whilst the permanent and generally more elaborate support system gets installed or constructed, still results in injuries to people. The authors wishes to explore the probability and practicality of making use of new generation support products to make the support operations safer as well as enhance productivity in the stope face. This paper will examine the use of Autorock Drills as a means to drill roof support holes and install appropriate support components into these holes, as well as the application of ?Thin Spray Liners?, commonly called TSL?s as an additional means of creating a safer operating environment. The installation of netting as a means of roof protection and other support aspects such as cemented roof-bolts will also be explored. These proposed items are envisaged to improve the safety of our people and reduce production down time and increase production and productivity.

Jan 1, 2008

By S. A. Scott

Mintek developed the MinataurTM leach-solvent extraction-precipitation technology as a cost effective, easily operated alternative to conventional gold refining processes. The technology was first commercialized at the Harmony Gold Refinery in 1997 to produce 99.99 per cent gold product and has subsequently led to development of various value-addition steps including the casting of various investment bars, gold wire drawing and gold potassium cyanide powder production. In addition to refining gold to high purity, if an appreciable amount of silver is present in the feed material it is also refined to 99.99 per cent purity. The major advantage that the Minataur? technology has over other gold refining processes is the relatively low gold lock-up and reduced operating costs. The operating cost1as at April 2001 for the expanded Harmony refinery (24-ton per annum gold production) was approximately half that of conventional smelting and toll refining. The extractant employed for solvent extraction is relatively cheap and highly selective for gold, making the technology attractive in situations where significant quantities of platinum group metals or base metals are present.

Jan 1, 2004

By J. M. Sabio, A. W. Stalberg

Keywords: Pyrometallurgy, furnace, calcium carbide, acetylene, Newcastle The manufacture of calcium carbide in Newcastle, South Africa, was started in the late 1950s by a company called South African Carbide, at the Ballengeich site. In 1978, this operation was bought by the forerunner to the present AECI Ltd, a large producer of commodity chemicals at the time. Production continued at this site until 1992. In the meantime, Karbochem, an operating division of Sentrachem Ltd, was also manufacturing carbide in Newcastle, as a building block for the manufacture of synthetic rubber. In 1990, the Karbochem calcium carbide operation was closed down. In 1992, the AECI carbide business and the Karbochem production facility were amalgamated, and production continued under the Karbochem name. In 1997, the Dow Chemical Company bought the holding company of Karbochem, and the carbide business continued operations until 2003. In June 2003, the business was sold to a management consortium as SA Calcium Carbide (Pty) Ltd. Later, in October 2004, 100% of the shares were acquired by the Andina Group. Today, the Andina Group, consisting of SACC from South Africa, CIL from UK, and ANDINA from Argentina, has become a global leader in the manufacture and supply of calcium carbide and calcium silicon, ferro silicon 75% and derivatives, recarburizers with low nitrogen content, acetylene, carbon black, micro-silica, and silicon metal. The production facilities at Newcastle comprise a 52 MVA submerged arc furnace of a closed design, carbon monoxide gas recovery, recovery of fine raw materials via a hollow electrode system, and an extensive computer-controlled process. These all enable an efficient state-of-the-art operation. The downstream processing facilities consist of screening and drumming facilities, milling facilities, an acetylene generation plant, and an acetylene carbon black plant. Clearly, SA Calcium Carbide (Pty) Ltd has a long history of supplying quality calcium carbide to the industries that it proudly serves.

Jan 1, 2006

By D. D. Munro

Finsch Mine is a kimberlite diamond mine located at Lime Acres in the Northern Cape Province of South Africa. The mine was founded in 1961 and started surface mining in 1964. Underground production commenced in 1990 using a modified blast-hole open stoping method for the mining of Blocks 1, 2 and 3. Block 4 is currently being mined as a block cave. The process of identifying and optimizing a method to mine the Block 5 orebody started in 1991, and in 2006 incline caving was identified as being technically feasible. This paper aims to document the process employed in developing this method by the Block 5 prefeasibility team as well as discuss the technical challenges encountered during this process. The paper commences with a history of Finsch Mine and highlights the complex geology and threat of sidewall failure that prompted the decision to use block caving as the mining method for Block 4. A literature study of mines that implemented mining methods upon which the incline cave was conceptualized is then presented. These practices were then used to form the basis for the designs on which the initial geotechnical modelling was done and built upon through an iterative process of modelling and design changes. The ventilation of the mining area, initial productivity simulation results, and the applicability of automation and comminution processes in the incline cave are also presented. The paper concludes with an investigation into some of the challenges of the mining method, and shows that that incline caving is a technical option available for further investigation in determining the optimal mining method to be employed at Block 5, Finsch Diamond Mine. Keywords massive mining, incline caving, geotechnical modelling.

Jul 1, 2013