Search Documents

By J. H. van Dalen, P. J. Brandt, F. W. Wessels

A maximum of ten process streams (Merrill barren solutions) can be monitored sequentially with this on-line analyser, and gold concentrations as Iow as 0,005 mg/I can be determined. The design is a further development of the Tell-tale analyser constructed by the Corner House Laboratories during the period 1965-69. The barren solution is preconcentrated automatically by solvent extraction, the solvent being a solution of I per cent Aliquat 336 in di-isobutyl ketone. An aqueous-to-solvent ratio of 40: I is maintained. The extracted gold in the organic phase is determined by flame atomic absorption, each analysis taking approximately II minutes. The long-term reproducibility of the absorbance readings over a 24-hour period of repetitive sampling of four simulated process streams varied from 6,9 to 4,1 per cent relative standard deviation for gold concentrations of 0,0 I to 0,05 mg/I.

Jan 1, 1980

This paper presents a quantitative approach to the problem of determining design capacity and field dimensions of underground coal mines using room- and-pillar mining systems. In evaluating these design variables, relationships among mining costs, number of production sections in mines, location of central shafts, mine field dimensions, section production, mine output, and cost of production losses due to underground man-traveling are analyzed. Thereby the unit cost of coal is expressed as a function of the design variables as well as input parameters such as seam angle, seam thickness, seam depth, underground traveling speed of men, mine recovery and plant recovery. The problem is then formulated as a nonlinear optimization model in terms of minimizing the unit cost of coal subject to a set of constraints and solved analytically for flat seams and numerically for inclined seams. Sensitivity analysis of the variables is also included in the paper.

Jan 1, 1987

By J. Svoboda, W. J. C. Venter, R. N. Guest

SYNOPSIS Wet high-intensity magnetic separation was examined as a method for the recovery of copper and lead from Tsumeb flotation tailings. Bench-scale and pilot-plant tests were conducted and, despite the very low magnetic susceptibilities of all the complex copper and lead minerals, copper and lead recoveries of over 60 per cent and almost 50 per cent respectively were obtained at a combined copper and lead grade of up to 13,5 per cent. The recoveries were found to be practically independent of magnetic induction in the range 0,5 to 2,2 T, and the grade of the magnetic concentrate decreased with increasing magnetic induction. The grade of the magnetic concen¬trate improved when the flowrate of the slurry was increased, and desliming was found to have a profound effect on the. metallurgical process. Particles smaller than 10 µm were not recovered, and their presence in inefficiently deslimed samples impaired the overall performance of the magnetic separation

Jan 1, 1988

By J. P. G. Pretorius

The size effect in tests of the compressive strength of coal specimens differs from predictions based on the Weakest Link theory. Predictions of the size effect in tensile tests on lengths of cotton yarn and glass fibre, the behaviour of which is analogous to the weak link process, also differ from observations. This discrepancy is shown to be caused by the correlation between the strengths of the unit lengths in a composite specimen. The Weakest Link theory is reformulated as the Weakness Correlation theory to account for such correlation. It is shown that weakness correlation is found in rock and it is concluded that at least part of the discrepancy between the predicted and observed size effect in rock strength tests could be attributed to this correlation.

A modified germanium recovery process in conventional zinc metallurgy, based on the understanding that ferric hydroxide has strong ability to coprecipitate germanium element, was presented. The relaxed lab-scale experiments were conducted to evaluate its technological feasibility. The experimental results obtained show the new process has great competitive advantage over the conventional one.

Jan 1, 2008

To the trustees of The SAIMM Scholarship Fund We have audited the annual financial statements of The SAIMM Scholarship Fund set out on pages 587 to 592 for the year ended 30 June 2005. These financial statements are the responsibility of the trustees. Our responsibility is to express an opinion on these financial statements based on our audit. Scope We have conducted our audit in accordance with International Standards on Auditing. Those standards require that we plan and perform the audit to obtain reasonable assurance about whether the financial statements are free of material misstatement. An audit includes: examining, on a test basis, evidence supporting the amounts and disclosures in the financial statements, assessing the accounting principles used and significant estimates made by management, and evaluating the overall financial statement presentation. We believe that our audit provides a reasonable basis for our opinion. Audit opinion In our opinion, the financial statements fairly present, in all material respects, the financial position of the trust at 30 June 2005 and the results of its operations and cash flows for the year then ended in accordance with South African Statements of Generally Accepted Accounting Practice.

Jan 1, 2005

By J. H. Bulloch

A study of fatigue-crack growth in a rail steel and an associated weld metal showed that fatigue cracks in the deformed rail steel had slightly higher growth rates than in undeformed rail steel. The crack growth in the weld metal was appreciably faster than either and exhibited plateaux that were above the upper bound reported for rail steels, The cyclic-life curves showed that, over an indicated service period of 8 years, both the deformed and the undeformed rail steels should not be prone to fatigue failures under the defined mechanical conditions, For the weld metal, the cyclic-life curves indicated the possibility of premature fatigue failures but, as al the input parameters represented a 'worst case' situation, this assessment could wel be ultra-conservative. In the rail steels at low levels, the extension of the fatigue cracks occurred by ductile striated growth. At a Kmax level of 35 MPa .J/n, cleavage facets formed initially on the surface of the fatigue fractures, and their incidence increased with Kmax until the onset of fast failure, The microstructure of the deformed rail steel exhibited cleavage facets at a slightly lower Kmaxvalue, and contained more cleavage facets at a given K level, than the microstructure of the undeformed rail steel. The average size of the cleavage facets agreed well with the pearlite nodule dimensions of 60 to 100 ILm. The microstructure of the weld metal was much coarser and contained columnar grains. At al f.K levels, the dominant fracture mode was cleavage, with small isolated regions of ductile striated fatigue cracks. The size of the cleavage facets varied from 150 to 600 ILm, and such a variation may be explained by the fact that cracking generally occurs in association with the pro-eutectoid ferite phase, and that this phase is distributed along some boundaries of prior austenite grains and the boundaries of the coarser columnar grains.

Jan 1, 1987

By H. M. Friede

Notes on the composition of pre- European copper and copper-alloy artefacts from the Transvaal by H. M. Friede. Ph.D. (Visitor) Seven copper artefacts (five ingots and two ornaments) found at prehistoric sites in the Transvaal were submitted to analysis. All the artefacts showed a high copper content and a relatively Iow level of impurities. A little-known ingot type from the Limpopo Valley ('nail' ingot) is described, and its analysis is given. The analysis of two copper ornaments that come from sites dated to the 5th Century AD. and the 11th Century AD. showed the constancy of the composition of copper articles over long periods. The well-known 'Blaauwberg Ingot' was re-analysed, and the results showed that this ingot cannot be regarded as a true bronze. Analytical values for the composition of three brass artefacts from Bambandyanalo (Mapungubwe), Northern Transvaal, are given. Some aspects of pre-European bronze manufacture and brass smelting, and of early metal trade from the East Coast into the interior of South Africa, are discussed.

Jan 2, 1975

By G. V. R. Landman

Changes in the explosion behaviour of mixtures of coal dust, methane, and air when exposed to different energy sources are discussed. Changes to the lower explosive limits, minimum ignition energies, and rates of pressure rise when the same hybrid mixture of coal dust, methane, and air is exposed to ignition sources which are either spatially extended or spatially concentrated, are examined. A diagram is presented from which coal-dust loadings and methane presence can be determined which are below the lower explosible limits, and stated as a safety factor.

Jan 1, 1995

By E. L. Thyse, P. Bepswa

The Western Cape Mineral Processing Facility (WCMPF) is a collaborative educational initiative between the Department of Process Engineering at the University of Stellenbosch and the Chemical Engineering Departments at the University of Cape Town and the Cape Peninsula University of Technology. The primary objective of the WCMPF is to facilitate the education, development and graduation of suitably qualified engineering graduates and diplomats for the mining and mineral processing industries. In recent years the WCMPF has embarked on a number of initiatives aimed at improving the quality of mineral processing education which include, more importantly the introduction of novel ?end to end? or ?integrated? practicals. The practicals are developed around a specific mineral theme or route, which more than often includes the development of several new pilot plant practicals demonstrating key unit operations or processes in the selected mineral theme or route. The most recent mineral processing pilot plant practical programme is developed around the beneficiation of heavy mineral sands. The programme consist of the following developed pilotplant practicals: the online electrostatic separation of free flowing mineral sands using a Roche Mining Carrara high tension roll separator incorporating a Blue Cube Systems MQi in-line mineral quantifier; the production of titania-rich slag and pig iron from the smelting of ilmenite and anthracite in a 60 kW direct current (DC) plasma arc furnace as well as the mineralogical characterization of the feed and products; the continuous closed-circuit ball milling and screen classification of titania-rich slag. This paper illustrates the important role of a well-designed heavy mineral sands beneficiation pilot plant practical programme in facilitating the education and development of suitably qualified personnel for the mining and mineral process industries.

Jan 1, 2007

By H. Wagner

It is a great privilege for me to have been asked to present the closing address to this most successful symposium on backfill in the South African mining industry. When I accepted this invitation I did not fully appreciate the tremendous progress made on most aspects of backfilling in the last few years. The number and quality of papers presented at this symposium bear testimony to the mining industry's determination and success in introducing backfill in underground mines to improve strata control and environmental conditions, and to provide better protection to mineworkers against the hazards of rockbursts and rockfalls. Many contributions demonstrated that these benefits can be achieved at a reasonable cost, and in some instances improved grade and higher rate of face advance result in improved economics. In my closing address I will attempt to summarize the progress made in the various aspects of backfilling underground workings and to identify those areas which, in my opinion, require further attention and effort. I will undertake this review under the following main headings: ? fundamentals of backfilling; ? design of backfill systems; ? operation of backfill systems; ? control of backfill systems; and other aspects of backfill systems.

Jan 1, 1988

By B. W. Wallace

Permitted explosives in South Africa are those explosives approved by the relevant State authority for use in fiery coal mines. The main tests that an explosive must pass for this approval are the gallery tests derived from the Buxton (U.K.) classification. These tests are described briefly. In addition, the safety of permitted explosives is affected by their ability to deflagrate, and to produce a naked flame after blasting, rather than to detonate fully. Tests done on this phenomenon are discussed. A further potential hazard of explosives is after-blast fume. The testing and behaviour of several permitted explosives in this respect are covered, both in the laboratory and in the field. Performance testing of permitted explosives, specifically the double-pipe, underwater, and ballistic mortar tests, and their relationship to field use, are considered in some detail. The application of traditional and new tests to permitted explosives leads to guidelines for the safe and efficient formulation and use of these products.

Jan 1, 1986

By J. Güntner

Most copper/cobalt ores from the Central African Copperbelt contain sulphidic compounds, which are not extractable in direct leaching. Roasting provides the possibility to transfer the valuable components into leachable compounds. In an operation window defined by temperature and off-gas composition it is possible to selectively oxidize iron sulphides to haematite and copper/cobalt sulphides to sulphates. Selective sulphating of the valuable minerals is an important condition for the subsequent leaching stage. The dissolved copper and cobalt are recovered by solvent extraction and electrowinning. This technology has been part of an established process for many decades. The concentrates from recent projects on the Copperbelt have lower sulphur contents, and frequently higher copper contents, than those from older projects. The paper shows the consequences of this trend for plant operation and explains useful counter actions by means of case studies. Autothermal combustion is ensured even at very low sulphur contents. Off-gas treatment has so far been based on SO2 removal through sulphuric acid production. The generated acid is used to make up acid losses in the hydrometallurgical plant section. This well-proven process combination is still the preferred route if the feed sulphur content is high enough; however, some cases may require different off-gas cleaning concepts without compromising on clean air quality. Roasting in a fluid-bed furnace remains the core of the technology. Fluid-bed roasters are easy to operate and provide an excellent control of the calcine quality. Different feeding and heat-recovery systems are used to provide a tailor-made solution for each project. Outotec built it first sulphatizing roaster in Zambia about 30 years ago. At that time, the roasting of metal sulphides was already one of the main technologies in the company. Outotec has developed roasting solutions for copper, gold, zinc, lead, molybdenum, and pyrite ores. The continuously expanded and upgraded research facilities provide an excellent basis for developing sustainable, energy-efficient, and economic solutions for copper and cobalt production in Africa.

Jan 1, 2012

By J. Güntner

Most copper/cobalt ores from the Central African Copperbelt contain sulphidic compounds, which are not extractable in direct leaching. Roasting provides the possibility to transfer the valuable components into leachable compounds. In an operation window defined by temperature and off-gas composition it is possible to selectively oxidize iron sulphides to haematite and copper/cobalt sulphides to sulphates. Selective sulphating of the valuable minerals is an important condition for the subsequent leaching stage. The dissolved copper and cobalt are recovered by solvent extraction and electrowinning. This technology has been part of an established process for many decades. The concentrates from recent projects on the Copperbelt have lower sulphur contents, and frequently higher copper contents, than those from older projects. The paper shows the consequences of this trend for plant operation and explains useful counter actions by means of case studies. Autothermal combustion is ensured even at very low sulphur contents. Off-gas treatment has so far been based on SO2 removal through sulphuric acid production. The generated acid is used to make up acid losses in the hydrometallurgical plant section. This well-proven process combination is still the preferred route if the feed sulphur content is high enough; however, some cases may require different off-gas cleaning concepts without compromising on clean air quality. Roasting in a fluid-bed furnace remains the core of the technology. Fluid-bed roasters are easy to operate and provide an excellent control of the calcine quality. Different feeding and heat-recovery systems are used to provide a tailor-made solution for each project. Outotec built it first sulphatizing roaster in Zambia about 30 years ago. At that time, the roasting of metal sulphides was already one of the main technologies in the company. Outotec has developed roasting solutions for copper, gold, zinc, lead, molybdenum, and pyrite ores. The continuously expanded and upgraded research facilities provide an excellent basis for developing sustainable, energy-efficient, and economic solutions for copper and cobalt production in Africa.

Jan 1, 2012

By P. G. Terrazas Prado

This paper presents the results of research on the development and application of a custom-made truck cycle and delay automated data collection system (TCD-ADCS) in a surface coal mining. Truck cycle and delay field data are locally stored in trucks and then synchronized and replicated through a wireless network into a centralized server containing an already-developed integrated production management system (IPMS). The system relies on motion sensing and distance travelled in order to automatically define the cycle starting/ending points, cycle time, position, and delay time. Connectivity and communication between loading equipment and trucks are also established. Communication between the equipment operators and TCD-ADCS system is via a user-friendly graphic interface. The hardware used for the development of this system consists of a rugged touch-screen personal computer, 2.4 GHz radio transmitter antenna, and a commercial GPS receiver. The system was developed, tested, and deployed at a surface coal mine in the USA. Keywords surface coal mining, truck and shovel, data collection, information systems.

Nov 1, 2013

By R. C. Urquhart, W. P. Channon, D. D. Howat

Discussion: The mode of current transfer between electrode and slag in the submBerged-arc furnace by w. P. CHANNON, R. C. URQUHART, and D. D. HOWAT J. MEINTJES I have read the paper with much interest, and I should like to make a few observations. (I) The experimental work deals with resistance heating by an electrode immersed in a slag... AUTHORS' REPLY We thank Mr Meintjes for his critical analysis and helpful comments arising out of his study of our paper. Possibly we should emphasize at the outset that our experiments all related to the conditions in which the lower portion of the electrode was immersed in molten slag. We believe, however,

Jan 12, 1974

By W. L. Van Heerden

In situ complete stress-strain characteristics of large coal specimens by W. L. VAN HEERDEN, B.Sc. Hons. (Pret.) (Visitor) The significance of ;n situ tests on large coal specimens is briefly reviewed. Tests aimed at obtaining complete stress-strain characteristics of large coal specimens with high width-to-height ratios are described. A formula for the relationship between strength and width-to-height ratios of coal pillars is proposed, and the influence of width to- height ratios on the deformation characteristics of pillars is discussed.

As part of a broad program to optimise the performance of their grinding circuit, BHP Billiton Cannington have installed an OCS© Expert system together with three VisioRockTM online particle size analysis cameras. The main purpose of the system is to stabilise grind size and feed to the flotation circuit. This particular application of OCS© is the first installation to incorporate Metso Minerals Process Technology-Asia Pacific's (MMPT AP) Dynamic SAG/AG Mill Model, which is able to predict numerous mill parameters that were previously unable to be measured with the existing plant instrumentation. Integrated into the logic of the control algorithm are online vision based, particle size measurements of the AG mill feed and recycle crusher product. This paper will describe the history of the project from initiation to date, the model and OCS© logic configuration, and demonstrate the significant benefits realised at Cannington mine.

Jan 1, 2007

By J. Kempken, T. Schreiter, R. Degel, H. Schmieden

After a short summary of the historical milestones of the submerged arc furnace, the paper will highlight different applications and their specific smelting furnace requirements in the non-ferrous area. Additionally, aspects of rectangular furnace design and the features of the copper cooling system for the side wall will be emphasized. Finally a state-of-the-art design tool as well as a new invention to improve slag cleaning technology will be featured, which shows great potentials especially for the PGM and copper related industry. Keywords: submerged arc furnaces, aerro alloys, non-ferrous, copper, slag cleaning, PGM, rectangular furnace, DC technology

Jan 1, 2006

By C. Rodrigues

This investigation compares the gas adsorption behaviour and capacity of three bituminous coals from South Africa, of similar rank, by assessing the characteristics of the raw coal, as well as the resulting float and sink fractions (at 1.80 cm3/g) obtained by density separation of crushed coal samples. Calculations were also made to obtain the raw coal gas storage capacity from the weighted contribution of both float and sink fractions results, thereby permitting comparison with the analysed results of the raw coal. The study demonstrated that the clean fraction of a coal has the highest capacity to retain gas in the sorbed state, followed by raw coal, and lastly the sink fraction, and re?confirmed previous investigations that showed minerals to be inhibitors of gas adsorption and retention.

Jan 1, 2008