Search Documents

By N. Dixon

This report summarizes all work performed under U.S. Bureau of Mines Contract J0377014, "Development and Evaluation of Noise Control Techniques for Taconite Processing Equipment." Three areas of taconite processing equipment, grinding mills, fine screens, and crusher screens have been investigated. Extensive noise and vibration measurements have been made on grinding mills in which the process parameters that affect mill noise have been identified, and the level of shell impact noise around the mill defined. A multiplexing telemetry system was used to obtain shell vibration measurements from a rotating mill. Mill noise control methods were investigated and a partial mill barrier was built and tested on a semi-autogeneous mill. A noise reduction of approximately 3 to 6 dBA was achieved on the falling side of the mill. The use of rubber mill liners on autogenous mills has been evaluated. The noise sources on fine screens have been quantified, and noise control treatments developed. Noise reductions of 11 to 13 dBA were achieved at positions around the fine screen and some in-service testing has been done. Noise measurents of crusher screens were obtained and noise control through resilient screen decks appears to hold the most promise. Additional benefits might be lower life-cycle cost, since the service life of resilient decks is claimed to be longer than steel.

Jan 1, 1983

By A. O. Ipsen

As part of the Bureau's intensive investigation of domestic manganese deposits, lots of ore for testing were collected by Bureau engineers during examinations of several properties in Juab County, Utah. One low-grade and two intermediate-grade samples (13.5, 25.3 and 27.5 percent manganese) were procured by engineers of the Bureau of Mines from the 900--and 1,100-foot levels of' the Tintic Standard mine, situated 2 miles southeast of Eureka, Utah. The ore bodies were described as blocks of ore approximately 60 feet long, 40 feet wide, and 20 to 100 feet deep. The manganese-iron association in the Tintic Standard ores was intimate, and no significant concentration of the low-grade sample was made by ore dressing, However, both of' the higher-grade samples were readily beneficiated to marketable manganese products. Ore from the Oxen No. 5974 claim, 2 miles northeast of Eureka, Utah was low in grade (19.4 percent manganese) and was not amenable to the production of high-grade concentrates owing to the intimacy of association of the manganese minerals with silica. However, a fair manganese recovery was obtained in a product that, when sintered, assayed plus 40 percent manganese. The ore body is reported to be a replacement in limestone and is composed of manganese oxides intermixed with silica, decomposed rhyolite, and limestone. The Fields property consists of five mineral claims situated 3 miles north of Eureka, Utah. The deposit is a replacement in a contact between limestone and a quartz dike. Tests were made on representative samples of a 50-ton lot stored on the property. Although the mineral association in the ore (22.2 percent manganese) is not particularly complex, the physical properties of the manganese minerals render the ore refractory to ore-dressing beneficiation. As the ores varied widely in physical and chemical characteristics, samples from each property were considered as separate ore-dressing problems.

Jan 1, 1949

By B. W. Madsen

A modified transpiration apparatus was devised by the Bureau of Mines to permit rapid and accurate measure of the vapor transport and vapor diffusion coefficients of antimony sulfide (Sb2S3) and other compounds at temperatures to 1,045 K. The apparatus was equipped with dual condensers and valves to switch the flow of vapor in a fraction of a second from one condenser to the other, thus allowing short-interval sampling under equilibrium conditions. Reliability of the technique was established by measuring the vapor pressure of ZnC12 as a function of temperature and comparing the results with published data. As part of an investigation of the vapor concentrations and species of accessory element sulfides associated with copper and zinc smelting, the apparatus was used to measure the rate of vapor transport and diffusion coefficients of vapor over liquid Sb2S3 as a function of temperature between 870 and 1,045 K. The calculated vapor density was combined with published direct measurements of vapor pressure to calculate the average molecular weight of the gaseous species. Average molecular weight of the vapor in equilibrium with Sb2S3 ranged from 286 to 112 g/mol over the temperature range studied.

Jan 1, 1983

By A. Visnapuu

Excessive noise and high vibration are inherently associated with equipment used in the mining, extraction, and processing of mineral resources. High vibration degrades structural components, often leading to catastrophic failure and loss of productivity, and excessive noise can result in permanent hearing loss. In order to foster efficient utilization of the Nation's mineral resources and minimize occupational hazards associated with mineral processing, the Bureau of Mines investigated the relationship between the microstructures of carbon and alloy steels and cast irons and their damping capacities (ability to absorb vibration). Researchers measured damping capacity and other properties and investigated the effects of carburizing, spheroidizing, and annealing. The investigators found that in carbon and alloy steels, rounded colonies of fine-grained pearlite in a ferrite matrix correlate well with low damping capacity. Steel microstructures that exhibit sharp-faceted pearlite in ferrite matrix and partially or fully spheroidized cementite in ferrite show considerably higher damping. In cast irons, the lowest damping capacity is associated with nodular graphite microstructure, and the specific damping capacity (SDC) increases as the graphite micro-structure progresses from nodular to compacted to flake. Predominant ferrite in cast irons is also associated with good damping. SDC data are presented for selected carbon and alloy steels and cast irons.

Jan 1, 1987

By Peter G. Groer

The commonly used exact methods (1-2) to determine the WL measure the total a activity or the total number of a counts during three preselected time periods. Due to the half-lives involved (TRaB = 26.8 min, TRaC = 19.7) I these methods take 3S minutes to complete the a activity Ra measurements. Methods using the total a counts, obtained at times less than about one RaB half-life after the end of sampling run into statistical 214 problems. These methods are almost blind to RaB (Pb214) as a consequence of its relatively long half period (see above) and the fact that RaB is a ß emitter. The way out of this dilema is to measure RaB directly through its ß activity. Since RaB's daughter Rae (Bi214) is also a ß emitter, the two f3 spectra have to be separated to obtain RaB alone. How this is accomplished 1s described in subsequent sections describing the theory of the IWLM and its calibration. 2.0 THEORY The IWLM samples air for two minutes and counts this airs ample for two minutes starting 3 sec after the end of the sampling period. The instrument has three channels. The lower a channel, the upper a channel, and one ß channel. The total RaA counts observed are accumulated in the lower a channel, the total RaC? counts are stored in the upper a channel. The total ß counts from RaB and RaC are recorded in the ß channel. These three quantities are functions of NA, NB, and NC, the unknown concentrations

Jan 1, 1975

By Terry Muldoon

In conventional noncoal, room-and-pillar mining, the cutting machine is frequently a major source of airborne dust. Water is often used for dust control. An evaluation of typically used water systems during this program showed that they reduced dust levels by 60 to 70 percent over dry cutting when at least 0.5 gpm of water was applied. These systems, however, are only marginally effective in maintaining compliance levels and the added moisture causes operational problems. During the program, three additional dust control systems were designed, fabricated, and evaluated. The first, a hollow cutter bar, was designed to capture dust in the kerf at the cutting zone. The system was only marginally effective in reducing dust levels due to its lack of control of other sources. Large quantities of material captured by the system made it operationally questionable. The second, a machine mounted exhaust system, was extremely effective in capturing virtually all the dust generated in the heading. The captured dust was ducted out of the heading and exhausted downstream in the crosscut. Exhausting the dust without scrubbing, however, creates problems for personnel working downstream of the cutting machine. Successful application would require changes to the mine ventilation system and mining sequence. The third, foam, injected foam from an onboard generator through a channel to the cutting zone at the tip of the bar. Test results showed that foam, using 1/3 to 1/2 the total fluid quantity, was equally effective when compared to the mine's current water system.

Jan 1, 1983

By Michael Rieber

The increase in f.o.b. mine prices of coal from $5/ton to over $18/ton in five years [1] has increased the significance of transportation costs. Coals produced in the vicinity of the consumer bear a much lower transport cost than those produced in the west. This differential may be used for flue gas desulfurization, other cleaning, or further processing of local coals. To the extent that western coals are cheaper to produce and have a lower sulfur content, they offset the locational disadvantage. To the extent that they have a lower heating value, the disadvantage is exercabated. Given the other conditions, an accurate analysis of transport costs will help suggest the location of coal mining and the moue of transport both transport costs and tariffs have risen. Together they have increased delivered coal prices, altered the balance between the use of coal and other fuels, helped to alter the location of mining activity, and put pressure on consumers to examine the cost effectiveness of alternative transport modes. Transportation options for long distance coal movements include rail, barge, pipeline, and EHV transmission lines. A summary of system parameters is shown in Table 2.1. Barge transport, pneumatic and slurry pipelines are discussed elsewhere in this report. Together with EHV, they have been the subject of previous studies [2,3,4]. Slurry pipelines have been shown to be especially useful where rails are not available [2] but the technical problems of dewatering, handling, and utilization of lines [5] remain unresolved. They are discussed in Section 3. Barge transportation depends on the location of the mine and consumer with respect to the waterway system. One drawback of barge shipment is interruptions due to winter, and low or high water conditions. Mine mouth power generation followed by EHV transmission of over 500 miles has been shown to be the most expensive means of delivering an equivalent amount of energy to consumers [2].

Jan 1, 1977

By T. W. Smelser

This Bureau of Mines report presents a review of underground testing, test results, and design guidelines of steel-fiber-reinforced concrete (SFC) mine support (cribbing) developed at the Spokane Research Center. The objective of the work was to verify, in field applications, the performance, economics, and acceptance by the mining industry of the SFC supports and establish design guidelines for their use underground. Results indicate superior performance, favorable economics, and enthusiastic acceptance by the mining industry.

Jan 1, 1983

By A. B. Cecala

It has long been known that ventilation is a cost-effective method to lower respirable dust concentrations in all types of mining applications. The National Institute for Occupational Safety and Health has been working on a number of different research techniques that use ventilation as a critical component to lower respirable dust levels at surface and metal/nonmetal operations in the United States. This article presents five such research efforts. The first research area discusses how improving the ventilation flow patterns in an iron ore mill facility lowered respirable dust concentrations by 31 pct throughout the primary grinding area. The second research area examines how respirable dust levels were lowered at a dimensional stone shop by using air cleaning units suspended from the ceiling. A third area discusses how improvements in ventilation at underground limestone mines lowered respirable dust concentrations. The fourth area examines how improvements in dust filtration and pressurization systems significantly impacted the air quality in enclosed cabs of surface mining equipment. The last area presents a newly developed clothes cleaning technique. This technique uses an air spray manifold to blow dust from a worker?s clothing in an enclosed booth, which confines the dust for capture and removal by a baghouse dust collector. These research areas represent an array of different control technologies to lower respirable dust concentrations. Ventilation is an integral part of these control technologies.

Jan 1, 2006

By James H. Cobbs

The utilization of large diameter drilled holes for mine shafts seems to have had its beginning in Europe about 1850 (28) where the mining industries of Germany and The Netherlands first used drilled shafts. Recent shafts in softer formations of diameters as large as 25 feet and as deep as 1, 700 feet have been drilled in both The Netherlands and Germany. The first shaft drillers utilized cable tool or churn drilling techniques which limit both hole diameters and drilling speeds. Though some churn drilling of shafts is still performed, rotary drilling has been the dominant technique for many years.

Jan 1, 1973

By George Watkin Evans

The United States Geological Survey has estimated 1 that the State of Washington contains 11,412,000,000 tons of bituminous coal and 52,442,000,000 tons of subbituminous coal, in beds more than 14 inches thick. As the present rate of production is about 4,000,000 tons a year, Washington apparently contains coal enough to supply Pacific coast markets for many years. The character of the coal beds of Washington renders the production of clean coal very difficult, and a considerable proportion of the output is washed before it is marketed. In 1915 Washington ranked fifth among the States in the amount of coal washed, though only twentieth in total output. In that year 37.9 per cent of the coal produced in the State was treated in surface cleaning plants.

Jan 1, 1924

By Raymond W. Hiteshue

Experiments were conducted al temperatures of 480° to 800° C. and hydrogen pressure of 6,000 p.s.i.g. to determine the effect of coal residence time on the conversion of a high-volatile bituminous C coal to liquid and gaseous products when using a semicontinuous apparatus designed fur rapid heating and cooling of reactants. The objective of the studies at high temperatures was to determine if appreciable quantities of coal could be converted to gaseous hydrocarbons and low-boiling liquid hydrocarbons. Experiments at lower temperatures were designed to indicate shifts in product distribution with respect to temperature and to learn more about the general mechanism of the reaction when using close control of coal residence time. One percent molybdenum, based on m.a.f. (moisture-and ash-free) coal, was used throughout this investigation. At 800° C., 6,000 p.s.i.g., and "zero" residence time) the yield of gaseous hydrocarbons was about 38 percent and the yield of oil about 4.5 percent, based on m.a.f. coal. With IS minutes residence time, under the same conditions, the yield of gaseous hydrocarbons was approximately 80 percent with no increase in yield of oil. Apparently at 800° C., and hydrogen pressure of 6,000 p.s.i.g. coal was rapidly carbonized to char with expulsion of volatiles. Char was then slowly hydrogenated to gaseous hydrocarbons without production of oil.

Jan 1, 1962

By Orlando Martino

This regional report covers the mineral industries of Canada and 40 countries and areas in Latin America and the Caribbean Basin. Also included is a brief description of the mineral potential of Antarctica. The Latin American region encompasses an area twice that of the United States. Latin America and Canada have a rich and diversified endowment of mineral fuels, metals, and industrial minerals. Tables 2 and 3 provide a summary view of the importance of Latin America and Canada's output of its major mineral commodities in world mineral supply in 1989 and 1990.

Jan 1, 1993

By Dwight L. Sawyer

To provide technology that can help decrease the dependence of the U.S. aluminum industry on imported bauxite, the main ore of aluminum, the Bureau of Mines is investigating the extraction of aluminum from abundant domestic reserves of kaolinitic clay. Miniplant studies of the continuous leaching of calcined kaolin with boiling 25-pct HC1 acid resulted in a 93- to 99-pct extraction of the acid-soluble alumina in the calcined kaolin feed. Data are presented for an acid leaching study carried out in three or four continuously stirred tank reactors (CSTR) in series, feed rates of 100 to 250 lb/hr of calcined kaolin, and total nominal residence times of 0.7 to 2.3 hr. A material balance for a 176-lb/hr calcined kaolin feed rate in a circuit consisting of three reactors, four classifiers, and five thickeners is given. Data provide detailed compositional and physical information for calcined kaolin, process liquors, and acid-leached residue solids.

Jan 1, 1983

By John P. Wagner

The details of a three-phase study (total time period of 12 months) entitled ?Fire Alert Systems for Metal and Non-Metal Mines,? are presented. Phase 1 consists of a state of the art survey on fire detection devices and gas sensing techniques. Phases 2 and 3 include laboratory screening and systems concepts testing on various detectors classified as products of combustion, optical view-field and contact (or thermal) types under incipient and flaming combustion conditions. Recommendations for a mine fire detection system to protect shaft, sealed off or mined out (from spontaneous combustion of sulfide containing ores and cellulosic materials), and fuel storage areas are also included. me principal problem area noted during Phase 1 study is the high expected occurrence of false alarming of products of combustion detectors (POC") subjected to normal mining operations---diesel vehicles and equipment and shot firing or blasting operations. Simultaneous gas sensing of either the ratio of CO/NOx or CO2/NOx with detection of one or more fire signatures (smoke, radiant energy, or heat sensing) is the recommended approach to discriminate against these operations.

Jan 1, 1975

By J. L. Howell, D. E. Pollock, A. B. Cecala, A. D. O’Brien

Dust from worker,s clothes has been shown to be a problematic source of personal dust exposure. A recently completed effort between NIOSH and the Unimin Corporation has resulted in a quick and effective way to clean worker clothing. The process involves a booth under negative pressure with an air spray manifold to supply compressed air to blow off the dust from the clothing. The overall system is designed to meet MSHA and OSHA requirements. Results of field testing indicated that the manifold cleaned the clothes 10 times faster and removed 50% more dust than cleaning methods used by workers today.

By ALBERT E. HALL, Arno C. Fieldner, Alexander L. Field

As a safeguard against excessive clinker troubles, specifications for the purchase of coal can be drawn to include the "softening" or "fusing" temperature of the ash. The value of such information has been recognized by the Bureau of Mines and has induced the bureau to investigab~ laboratory methods of determining the fUSIbility of coal ash, and the bearing of the results on clinker formation in fuel beds. The bureau realized that the fusibility of a mixture of oxides and silicates snch as is comprised in coal ash ,'aries according to the conditions under which tests are made, and that in the absence of any generally accepted method, no agreement is to be expected among tests made in differ«:-nt laboratories. Indeed, Marks a has recently called attention to differences as great as 3900 C. that were obtained with the same sample of ash by two different laboratories. Therefore if a fusion-temperature clause is to have any place in specifications for coal, a standard m('thod of t('sting should be adopted in order to insure comparable results by different laboratories and to obtain the softening or fusing temperature of the ash unde:'r conditions similar to those of a fuel bed. After a consistent method has been devised for obtaining comparable:' results at different laboratories, there will remain the correlation of these results with those from the burning of coal in furnaces before the value of fusibility tests in coal specifications can hE' finally determined.

Jan 1, 1918

By D. Harrington

"FOREWORDVirtually all government agencies undertook many additional responsibilities during the period immediately preceding World War II; these responsibilities increased vastly in importance and scope after the actual declaration of war following the attack on Pearl Harbor. The Bureau of Mines was one of the agencies thus affected, and it was called upon to perform many duties foreign to its normal peacetime activities.The Health and Safety Division of the Bureau of Mines, at that time designated the Health and Safety Branch, was given several important and difficult duties and responsibilities of an unusual nature because of the war while of necessity-continuing its normal functions of assisting the mineral industries in the preservation of life and health and the protection of property, this being of especial importance in wartime because of the pre-eminent importance of having maximum output of essentially all types of mineral products. Some of these additional functions were given to the Health and Safety Division because the organization of the Division, with its field set-up dividing the Nation into districts with competent, experienced personnel in charge of its work, provided the nucleus of personnel and procedure through which rapid and smooth expanded functioning was feasible.In addition to the responsibilities directly attributable to definite war activities, such as the administration of the wartime Federal. Explosives Act and the Mineral Production Security Branch a new branch (then designated division) was formed to investigate coal-mine health and safety problems after the enactment of the Federal Coal-Mine Inspections and Investigations Act, which became a law on May 7, 1941, but which actually began to function actively after the declaration of war in December 1941.The purpose of this publication is to provide a brief historical record of the activities of the Health and Safety Division as a whole and of its individual branches during the war. The detailed record has been filed in the Archives Building, Washington, D. C."

Jan 1, 1949

By L. C. IlsLey

The theory and practice followed by the Bureau of ones in the investigation of electrical equipment4/ made for service in massy mines are of particular interest not only to manufacturers but also to those organizations that deal with safety and inspection at the mines. This publication proposes to discuss the theory, upon which tests of equipment in explosive atmospheres are based and to consider inspection and other matters pertaining to investigations made bar the Bureau in ascertaining whether a machine merits approval.

Jan 1, 1941

By Robert S. Becker

The results of a laboratory investigation of coal cutting mechanics and noise is presented. These experiments were performed using a linear cutting apparatus that operates over a broad cutting speed range. The influence of several coal cutting parameters on the noise, force, productivity, and specific energy associated with linear cuts is ascertained. Some basic theoretical aspects of coal cutting mechanics and noise generation are discussed, and the results of the laboratory experiments are used to Formulate analytical models of the coal cutting forces and noise. The analytical model For coal cutting noise is then generalized to account for the more important effects of rotary cutting. Based on the generalized model, an estimate of the sound pressure level at an operator's position is made for a typical continuous mining machine. It is concluded that by employing linear rather than rotary cuts, using deeper depths of cut, slower cutting speeds, and more efficient cutting tools, it is possible to reduce the level of coal cutting noise, as well as Provide benefits to other important areas of underground health and safety.

Jan 1, 1980