Search Documents

By R. E. Mussler

As part of an overall goal to develop technology that can maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines is evaluating a method for selectively extracting nickel and cobalt from low-grade domestic laterites. The method involves electrowinning to recover the metals in pure form; therefore, preliminary laboratory-scale electrowinning tests were conducted in both a nondiaphragm and a diaphragm cell to determine the effect of variables on energy efficiency under controlled conditions. Electrolytes were generally reagent-grade sulfate solutions that were prepared to simulate electrolyte that could be obtained by stripping nickel-and cobalt-rich solvent extraction reagents. Limited tests were conducted with electrolyte generated from laterite leach solutions. Electrical energy consumption in a nondiaphragm cell was 2.06 kwhr/lb Ni with the cell operated at 50° C, a cell feed of 90 g/l Ni, a pH of 3.5, an extraction of 3.2 g/l, and a cathode current density of 20 amp/ft2. The energy requirement decreased with increasing concentration and temperature, and increased with increasing. extraction and current density. At 50° C, energy consumption in the nondiaphragm cell was 21 pct greater than in the diaphragm cell, but it was only 5 pet greater at 65° C. For this reason and because of overall cost considerations, operation at 65° C with the nondiaphragm cell was preferred. Smooth sheets of cobalt were obtained by electrowinning in a nondiaphragm cell at selected temperatures from 50° to 85° C and with cobalt concentrations from 55 to 87 g/l. The energy consumption (1.48 kwhr/lb) was 22 pet lower with a cobalt concentration of 75 g/l and a cell temperature of 65° C than with a cobalt concentration of 55 g/l and a cell temperature of 50° C.

Jan 1, 1981

By Liming Yuan

In order to reduce fire hazards caused by spontaneous combustion in longwall gob areas, a computational fluid dynamics (CFD) study is being conducted by National Institute for Occupational Safety and Health (NIOSH) to simulate the spontaneous heating of coal in longwall gob areas. A CFD model was first developed to model the spontaneous heating process in a two longwall panel district using a bleeder ventilation system with a stationary longwall face. The spontaneous heating is modeled as the low-temperature oxidation of coal in the gob using kinetic data obtained from previous laboratory-scale spontaneous combustion studies. Heat generated from coal oxidation is dissipated by convection and conduction, while oxygen and oxidation products are transported by convection and diffusion. CFD simulations were then conducted to model the spontaneous heating in longwall gob area with a bleederless ventilation system. A single longwall panel with a bleederless ventilation system was simulated. The effect of gob permeability on the spontaneous heating was also investigated.

Jan 1, 2009

By H. L. Burmeister

These properties were examined by a Bureau of Mines engineer in 1949. During 1950, these mines were studied by the Bureau to determine the possibility of increasing the production and augmenting the supply of fluorspar. As a result of this study, it was decided to core-drill the Knox-Yingling vein to test the continuation of fluorspar to a greater depth than that reached by mine workings. It also was desired to relate the present deposit with the Rosiclare formation. Development work by the Bureau of Mines was performed from February to May inclusive in 1951. Four diamond-drill holes aggregating 2,733 feet were drilled in the hanging wall of the vein.

Jan 1, 1952

Reduce fire warning time and avoid activation of false alarms in underground mines. Approach A heat activated stench/tracer gas system was developed which automatically releases the gas mixture into the mine ventilation air. How It Works A canister approximately 12 inches long and 3 inches in diameter is charged with 50 grams of ethyl mercaptan or other appropriate stench gas and 500 grams of instrument detectable Freon. The canister is then pressurized to 100 psi with nitrogen. A disc is used to seal the contents of the canister. A low-temperature alloy designed to melt at a predetermined temperature is used to restrain a spring loaded plunger. Upon exposure to heat, the alloy melts and the plunger is released. The plunger ruptures the disc and the mixture of stench and tracer gas is released from the canister. Canisters are mounted in areas of a mine which are susceptible to fire such as near

Jan 1, 1983

By H. B. Salisbury

The Bureau of Mines conducted research to determine if low-grade California chromite ores could be beneficiated to produce products suitable for commercial use. This research is part of a Bureau goal to provide technology capable of using low-grade domestic ores to meet emergency demands of the Nation for metals and minerals and in particular those minerals, such as chromite, which are considered critical. Two ores from California were ground and treated using gravity concentration and magnetic separation techniques. An are from Auburn in central California, assaying 2.5 pct Cr203, was treated by tabling and magnetic separation to yield a nonmagnetic product containing 44.7 pct Cr203 at a recovery of 36.4 pct. Core drilling samples from the Seiad Creek area of northern California, assaying about 6 pct Cr203, were upgraded by tabling to yield a concentrate containing nearly 50 pct Cr203 with a recovery of 50 pct. Both products are suitable for metallurgical and/or chemical use.

Jan 1, 1981

By Sidney Katell

An estimated capital investment of $76,499,800 will be required for a plant designed and built to produce 90 million standard cubic feet per day (std.c.f.d.) of synthetic pipeline gas through Lurgi gasification of bituminous char. This investment figure does not include the pretreatment plant, the cost of which is assumed to be reflected in the cost of the char fed to the gasification system. Shift conversion, C02 removal, and methanation are required after gasification in the Lurgi unit to make a gas suitable for pipeline transmission. Capital investment data are based upon equipment costs, January 1959. Based on a 90-percent or 330-day operating year, the operating cost before profit and Federal taxes with the char price as a variable will amount to the following: [ ]

Jan 1, 1959

By M. J. Brevoort

Research work in the Bureau of Mines cryogenic laboratory requires the use of high-sensitivity galvanometers of the d'Arsonval type in a building that is subject to unusually severe vibrations. A modified form of the galvanometer suspension described by Julius' has damped the vibrations so successfully that a short note concerning it is thought to be desirable. The laboratory is on the site of the Amarillo helium plant near a building that houses gas engines of from 180 to 250 hp driving compressors and electric generators. The distances from the galvanometers to the individual engines range from about 80 to 180 feet. The subsoil, consisting of black clay loam, transmits the impulses without much damping. The usual methods of protecting galvanometers from vibration were tried and proved fruitless. A Julius suspension purchased on the market was carefully installed in the hope that it would overcome the difficulty, but the conditions were too severe even for this elaborate arrangement. Several modifications of the original Julius suspension, which were then introduced, resulted in almost complete elimination of all vibrational effects. These modifications were suggested by careful study of the original idea embraced in the Julius construction. They were designed to give further constraint to motion in any direction other than that parallel to a line from the point of support through the center of gravity of the suspension, This was accomplished by making the suspended frame more rigid and by improving the means of adjusting each of the supporting wires to the same degree, thereby transmitting any impulse symmetrically through the three wires. The result was a suspension that is more effective, particularly for severe vibration, than the form described by Julius; also, it is believed to have advantages in stability, simplicity, and ease of adjustment over the few suspensions for this type of service that the author has found described in the literature.

Jan 1, 1931

By T. L. Joseph

"In the January 3 issue of Iron Trade Review, Sweetser2, in referring to the problem of coke combustibility, points out that, ""Someone should formulate a rule for the rate of flow of coke through the zone of coke combustion that now appears to be confined to a comparatively restricted volume in front of the tuyeres,"" In formulating such a rule it is necessary to distinguish clearly between combustibility, a property of the fuel, and rate of combustion, which is determined by the rate at which air is supplied to the fuel bed. The rate of carbon gasified at the tuyeres of a blast furnace is independent of coke combusti-bility. A fast-burning coke will burn in a more restricted volume than a slow-burning coke, but both types of fuel will be consumed at rates determined by the supply of oxygen,A number of the definitions of combustibility that have appeared in technical literature relate more closely to rate of combustion than to combustibility. Perrott and Kinney) have correctly defined it as follows: ""Combustibility of coke from the standpoint of its use in, the blast furnace is inversely proportional to the mean rate of gasification per unit volume of the combustion zone, assuming other factors remain constant,"" Combustibility of coke refers therefore to those properties that determine the size or extent of the combustion zone. Relative differences in these properties can be measured by the depth of the fuel bed required to convert oxygen from the air into carbon monoxide."

May 1, 1924

By Robert P. Vinson, Fred N. Kissell

This report describes three coal mine ventilation studies by the Bureau of Mines in which sulfur hexafluoride (SFG) was used as a tracer gas. One of these studies was conducted to determine air movement and leakage in a sealed area. Another was run to determine the ventilation efficiency of a bleeder system. Finally, a study was made of air leakage across permanent stoppings of parallel intake airways. These studies proved sulfur hexafluoride to be a useful addition to the equipment commonly used in coal mine ventilation analysis.

Jan 1, 1976

By Edward D. Thimons, Jay F. Colinet

NIOSH conducted a strategic planning effort to identify those areas in mining with the greatest research needs. Data analysis and stakeholder input identified the need to reduce worker exposure to respirable crystalline silica dust as a high priority area. MSHA dust sampling data were analyzed to target the mining commodities and occupations with the greatest percentage of samples containing silica above compliance levels. In response, the Pittsburgh Research Laboratory (PRL) has implemented a multi-faceted research program to improve silica dust control for these problematic commodities and occupations. A review of silica compliance trends, PRL silica research programs, and recent control technology developments are provided here.

By Thomas M. Barczak, Ron Smith

Steel liner plates, which are bolted together to form a shell, are commonly used to provide temporary protective linings in the tunneling industry to ensure the stability of the tunnel and safety of the workers until more permanent ground reinforcement can be installed. As the ground deforms to try and close the opening, the liner plate is radially stressed, and by deforming redistributes these loads back to the surrounding insitu earth. Grouting behind the plates is done to fill any voids and ensure uniform contact to the strata around the back of the plates. Another function of the liner plate in some applications is to act as a platform or structure for the mining machine to react against in order to develop the necessary forward thrust to be able to excavate the face. In this case, the liner plates are loaded axially as a horizontal column of bolted liner plate rings, creating a jacking force against the liner plate assembly. In general, the buckling strength of the plate sections determines the jacking force capacity. Historically, the jacking force capacity of tunnel liner plates has been theoretically determined by some simplistic equations developed from tests of single liner plates. Recently, full-scale tests on a complete circular section of bolted liner plate ring segments have been conducted in the NIOSH Safety Structures Testing Laboratory using the unique Mine Roof Simulator to apply controlled loading in a manner that simulates the real world environment. Due to the unique size and capacity of the Mine Roof Simulator, these are believed to be the first full-scale tests conducted on the jacking force capability of tunnel liner plate rings. These tests indicate that the previously used theoretical equations tend to over predict the jacking force capacity of these tunnel liner plates. Unanticipated deformations in the field have been observed at loads below these theoretical design loads, therefore, a more accurate determination of the jacking force capability was needed. This report summarizes the full-scale test results, examines design parameters that impact the jacking force capability, and develops new mathematical models to improve the prediction of design loads.

By James Paone

The Bureau of Mines conducted laboratory drillability studies on nine rock types using two mining-type percussive drills. Percussive-bit action was simulated by dropping a known weight on a rock sample to obtain a coefficient of rock strength for each rock drilled. While no single physical property of a rock is completely satisfactory as a predictor of penetration rate, coefficient of rock strength showed a better correlation with penetration rate than did other physical properties. Results also indicate that over the range of energies investigated, energy per unit volume in a given rock is independent of blow energy. A drillability index for the percussive system is proposed that utilizes the coefficient of rock strength test to determine energy per unit volume for a given rock which, along with the work rate of a given drill and the bit diameter, is used to predict the penetration rate as shown in the following equation: [R = 4P pD2 E, where R = penetration rate, in/min, P = work rate, in lb/min, D = bit diameter, in, and Ev = energy required to produce a given volume of rock, in lb/in3.] Laboratory tests indicate this method's potential as a simple and reasonably accurate method of predicting penetration rates with any percussive drill and bit combination.

Jan 1, 1969

By Byron. O. Pickard

"An Arizona mining company recently demonstrated a new use for the geophone by successfully locating leaks in compressed-air lines which were buried under from 1-1/2 to 2-1/2 feet of fine rock fill. The following information is abstracted from data sent to the Bureau of Mines by the superintendent of the mine.The company has two parallel main compressed-air lines, about one and one-half miles long, buried under an average of two feet of fine rock fill. One of the lines is a four-inch high-pressure (1000 pounds) main, and the other line a ten-inch low pressure (90 pounds) main. The two mains are separated by a 10 to 3C foot interval, and run from the compressor plant to the No. 2 shaft, where they are taken underground. A pump line is also buried in the immediate vicinity.Several leaks, not audible enough to be located, were developed in the Alms. Various =Abode were suggested that did not seem practicable to the management. Finally, the company obtained a Bureau of Mines' geophone and experimented with it. The first test& were conducted while the pumps were running, and while there was noise on the concrete pavement, all of Which caused so much vibration in the geophone that it was impossible to detect the leaks.The second attempt was made at the close of the day shift when the compressors were not operating and when the pumps could be shut down. The valves in the far end of the surface lines were closed, and the lines were pumped to full pressure (90 and 1,000 pounds respectively).Geophone readings were then taken at 7 or 8 foot intervals directly see the lines. Several leaks some very large in the high-pressure line were audible with the geophone at distances varying from 15 to 30 feet. A con-le leak in the low-pressure line was found at a distance of 10 feet. detecting the leaks, no difficulty was found in locating them exactly. ""At this time"", laid the superintendent of the mine, are unable to large a leak must be in order to be located under two feet of loose geophone. The fill we worked over was quite loose and dry and unfavorable for the work in question. However, we have no that the instrument is a valuable adjunct to our business""."

Aug 1, 1922

By D. J. Parker, D. Harrington, L. H. Harrison

The necessity for protection against the hazards of lightning manifests itself from time to time in the mining industry by reason of loss of life, damage to electrical equipment, fires in surface structures at mines, and accidents in the handling and use of explosives. This paper is intended to assemble, correlate, and present some of the salient. points embodied in the available literature on the subject and at the same time give some factual data concerning instances of such loss of, life and damage to property, with special application to the mining industry The annual loss of life and destruction of property by lightning is considerable; the former may be prevented to a limited extent, though use of common sense as to exposure is required and not always followed; the latter can be prevented to a considerable degree. The manufacturers of electrical equipment,, through improved types of lightning arresters,, have done much toward the protection of electrical equipment, with consequent safeguarding of life and of property. Education based on unfortunate experiences has gone far to discourage the handling of explosives and blasting accessories during thunder storms, especially in open pits and quarries, and to a much smaller extent in underground workings. The lowly lightning rod plays an important role in the protection of certain types of buildings (especially isolated buildings), stacks, monuments, and other structures. LIGHTNING PHENOMENA In 1751, Franklin proved that lightning was simply a visible display of electricity - an extended spark; and until a generation ago little had been added to his exposition, to define the various phases of the phenomenon. Matters pertaining to lightning are discussed in the following references:

By R. E. Morgan, J. F. Barkley

"INTRODUCTION In city smoke-abatement work it is customary to require approval of the sizing of fuel-burning equipment. This is to insure that, with reasonable attention, the equipment can be operated essentially smokelessly, having such features as ample furnace volume and air supply. To answer the many inquiries that come to the Bureau of Mines as to what dimensions are acceptable and standard, the requirements of a number of smoke-abatement ordinances have been tabulated.CONCLUSIONSStudy of these tabulations shows that even after many years of fuel-burning practice and experience there is no common standard. Variations in the requirements for the same type of equipment under the same conditions of operation are great. This causes considerable difference in installation costs. Over-all costs being affected, the competitive positions of different types of fuel-burning equipment are also affected. It is apparent that there is a lack of information as to proper dimensions that is commonly accepted as authoritative.DISCUSSIONTable 1 gives the minimum furnace-setting heights required by various cities for mechanical underfeed stokers installed under H.R.T. boilers. Figure 1 shows a typical installation. The dimension given for each case is the distance from the dead plate of the stoker to bottom of boiler shell, unless otherwise noted. As shown in the table, different cities use different size-classification systems; it is not possible to make complete, exact, direct comparisons. Table la gives a comparison for various cities, showing the approximate percentage difference in H.R.T. furnace-setting heights required from those recommended by the Stoker Manufacturers' Association arbitrarily chosen to serve as a basis of comparison. The percentages are approxi¬mate because they were calculated as if all heights as given were measured from the dead plate of the stoker. In two cases a lower height is permitted, in a number of cases the height may be the same, and in a number of cases the height must be greater. The percentage increase goes to 100 in one case. Lack of uniformity is quite evident."

Mar 1, 1950

By Dean H. Ambrose

A computer model was created that generates contact data by means of simulation while altering several variables associated with the machine and its operator. These variables include work environment, the operator's anthropometry, work posture, choice of risky work behavior, and the machine's appendage velocity. In the model, a contact means two or more objects intersecting or touching each other, e.g., the appendage colliding with the operator's hand, arm, head, or leg. This report documents the code development of special features of the computer model, random virtual human motions and behaviors, which made it possible for researchers to study hazardous interactions, such as contacts between the operator and machine. The original idea for random virtual human motions began with the need for a model that, when simulated, would experimentally mimic machine and human actions that could cause actual injuries or fatalities in the workplace. Injury incident investigation reports do not usually contain enough information to aid in studying this problem, and lab experiments with human subjects are also not feasible because of safety issues and ethical issues. Early investigation that evaluated the feasibility of random motions resulted in a primary programming structure and building blocks for code expansion. Basic motions and standard derivation data provided random parameters for the operator's movement in the random motion code. Experimenting with basic motions in preliminary models helped researchers devise a random motion technique that worked with xyz motion parameter values from basic motion parameters. Both values were the building blocks used in motion commands that comprised the core of the random motion code. When the code is executed in a three-dimensional computer model, it generates realistic starting positions for the operator's (virtual human) body and body parts and realistic motions mimicking a work sequence with a valid range of variation in movements. Researchers developed several rules for the random motion technique that, when applied, will maintain directional integrity of a virtual human's basic motions. From previous research, researchers formulated the algorithm that determines the behavior during machine operation. The decision algorithm was needed by the random motion code to randomly select what behavior to use for a simulation execution for a realistic representation of the operator's motions and risky behaviors during work tasks. The operator's chance of avoiding the moving appendage was also a concern to ensure that data reflecting a near-miss would not be considered a contact. Therefore, to filter a database obtained from simulations for actual contacts, it was necessary to track the operator's field of view and determine from this information when the appendage is in and out of the operator's view. NIOSH researchers successfully applied random motions and risky behaviors to examine the speed range of a roof bolter machine appendage for different workplace scenarios and compare statistically which is most likely to cause contacts (and possible injuries) to miners. Researchers in this study believe that the use of such simulations, treated with advanced statistical procedures, are extremely useful tools to evaluate the hazards of tasks where it is not possible to perform experiments with human subjects.

Jan 3, 2004

By Iam Pou Ng

Combustion aerosols consist mainly of elemental and organic carbon (EC and OC). Since EC strongly absorbs light and thus affects atmospheric visibility and radiation balance, there is great interest in its measurement. To this end, the National Institute for Occupational Safety and Health (NIOSH) published a standard method to determine the mass of EC and OC on filter samples. Another common method of measuring carbon in aerosols is the aethalometer, which uses light extinction to measure "black carbon" or BC, which is considered to approximate EC. A third method sometimes used for estimating carbon in submicron combustion aerosols, is to measure particle size distributions using a scanning mobility particle sizer (SMPS) and calculate mass using the assumptions that the particles are spherical, carbonaceous and of known density. With an eye toward evaluating the use of these methods for measuring carbon in freshly emitted diesel aerosols, the objective of this paper is to compare the results among these methods and to investigate the role of OC when measuring the mass concentration of elemental carbon (or black carbon) in aerosols emitted by a medium-duty Diesel engine. Results indicate that the aethalometer response correlates well with the data from filter samples (R2 = 0.99), with a very slight positive interference at high levels of OC.

Jan 1, 2008

By M. J. Brevoort

Research work in the Bureau of Mines cryogenic laboratory requires the use of high-sensitivity galvanometers of the d'Arsonval type in a building that is subject to unusually severe vibrations. A modified form of the galvanometer suspension described by Julius3 has damped the vibrations so successfully that a short note concerning it is thought to be desirable, The laboratory is on the site of the Amarillo helium plant near a building that houses gas engines of from 180 to 250 hp., driving compressors and electric generators. The distances from the galvanometers to the individual engines range from about 80 to 180 feet. The subsoil, consisting of black clay loam, transmits the impulses without much damping. The usual methods of protecting galvanometers from vibration were tried and proved fruitless. A Julius suspension purchased on the market was carefully installed in the hope that it would overcome the difficulty, but the conditions were too severe even for this elaborate arrangement. Several mudifications of the original Julius suspension, which were then introduced, resulted in almost complete elimination of all vibrational effects.

Jan 1, 1931

By E. Morrice

Gadolinium, dysprosium, and yttrium are difficult to electrowin as high-purity liquid metals because of their high melting points (>1,300° C). Samarium metal is difficult to prepare directly by electrolysis because the metal reacts with the electrolyte. In this Bureau of Mines study, the rare-earth metal was electrodeposited on a solid manganese, chromium, or iron cathode to form a low-melting alloy. The alloy was then vacuum distilled to separate the rare-earth metal from the ferrous metal. A typical samarium metal product, obtained as the distillate from vacuum distillation of a samarium-iron alloy, contained 150 ppm oxygen, 80 ppm carbon, and 50 ppm iron as impurities, Gadolinium metal, obtained as a residue from the distillation of a gadolinium-chromium alloy, contained 300 ppm oxygen, 200 ppm carbon, and 100 ppm chromium.

Jan 1, 1969

By M. K. Larson, B. G. White

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are investigating the causes and mechanisms of roof failure in underground mines. It is expected that a better understanding of these causes and mechanisms will lead to better layout and support designs that will help prevent accidents and fatalities associated with fall of ground. Two numerical experiments were conducted by NIOSH researchers using the Fast Lagrangian Analysis of Continua (FLAC) computer modeling program with a strain-softening continuum to simulate fracture zones. Two models, one of a round hole in a plate and one of a rectangular opening, were constructed and boundary conditions were applied to simulate far-field shear. The Particle Flow Code in Two Dimensions (PFC2D) computer program was used to look at the effects of far-field shear in generating fractures around an underground opening, but these models are preliminary until boundary conditions, strengths, and stiffnesses are matched to the FLAC models. Results showed that shear zones propagated from the opposite corners of openings in directions that appeared to be determined by opening shape and far-field stress. Tensile failures also formed and extended away from these shear zones. The consistent direction of shear deformation with respect to far-field shear provides a plausible explanation for preferred directions of shear as seen in geologic environments.