Search Documents

By J. M. Kuchta

The Bureau of Mines used laminar hot air jets of l/8- to 3/4-inch diam-eter to determine the hot gas ignition temperatures of various combustible vapor-air mixtures. The combustibles were n-hexane, n-octane, n-decane, a hydrocarbon jet fuel (JP-6), and an adipate ester aircraft engine oil (MIL-L- 7808). Minimum ignition temperatures occurred at a fuel to air weight ratio of about 0.5 and were not greatly sensitive to variations of fuel concentra¬tion. Moderate variations of jet velocity also had little influence on these ignition temperatures. However, these temperatures decreased with increase in heat source dimensions (jet diameter). The hot gas ignition temperatures of the combustibles were not necessarily much greater than corresponding autoignition and wire ignition temperatures when the size (,F the heat source and the ignition criterion were the same.

Jan 1, 1966

By H. H. Storch

Methane is the chief constituent of natural gas, and large quantities of it are also obtained in coke-oven gas and in the off-gases from cracking higher hydrocarbons. Perhaps the most important potential chemical use of methane is in the production of higher hydro- carbons, both aliphatic and aromatic. The results of a relatively large number of researches have been published in the technical and patent literature on the thermal decomposition of methane, the objective being an industrial process for the production of "antiknock" motor fuel. No industrially feasible process has, however, been developed. An inspection of the literature on this subject indicates that the chief difficulty in the way of accomplishing this object lies in controlling the decomposition so that undesirable products are eliminated. A considerable number of quantitative experiments have been reported, the results of which provide only a vague and confusing picture of the various steps in the thermal decomposition of methane. The reaction mechanism has not been subjected to rigorous fundamental study, and the necessity for such a study is obvious if further progress is to be made. The thermal decomposition is only one of the reactions of methane which are of potential industrial importance and which require further fundamental investigation. The oxidation, hydrolysis, and halogenation of methane are other reactions which must be studied further. In view of the importance of methane as a raw material for various industrially desirable products, it is appropriate that a survey be made of the important facts concerning the physical and chemical properties of methane which will serve as an aid in subsequent experi- mental work. No attempt will be made to present a complete chronological review, but rather a condensed critical description of the important literature will be presented.

Jan 1, 1932

Design a model health and safety program which, when implemented, can improve mine safety by reducing occupational injuries and accidents. Approach The Bureau of Mines developed a model program which identifies the elements essential to the effectiveness of health and safety programs designed for mining operations, and is readily adaptable to all types of sizes of mines. The model program primarily provides training on loss control and accident investigation and technical assistance with health and safety problems. In order to assess the effectiveness of the program, it was tested at both a coal and gold mining operation. Monthly statistics were generated to reflect the number of occupational injuries and accidents, and the severity of injuries (as measured by the number of work days lost during recovery). Observations were made of employees performing a large number of randomly selected jobs in order to estimate. the proportion of the workforce that was working in the presence of one or more of three types of safety deficiencies: Type A-individual job performance deficiencies which could be corrected by the employee alone I e.g., an employee is seen not wearing a seatbelt.

Jan 1, 1986

By R. E. Peterson

The Bureau of Mines has undertaken beneficiation investigations on samples representing large tonnages of oxidized taconites in order to develop and evaluate applicable technologies for producing iron oxide concentrates from these materials. Information derived from the investigations can be used to expand the domestic iron raw-materials base and to establish the impact these taconite deposits may have on future national iron ore requirements. This report describes a process that includes reduction roasting, magnetic separation, and flotation, applied to a western Mesabi Range sample taken near Coleraine, Minn. The sample contained 36.8 pct iron and 46.0 pct silica, and represented 0.5 to 1 billion tons of crude material. An average of 962 lb/hr of oxidized taconite was roasted with 33 lb/hr of lignite in a 35-foot-long rotary kiln. Pulverized lignite and natural gas maintained the kiln operating temperature at 850° C. The roasted taconite was beneficiated by magnetic separation and cationic flotation in a 900-lb/hr pilot plant and yielded a product analyzing 68.1 pct iron and 4.6 pct silica, and containing 82.4 pct of the iron in the kiln feed.

Jan 1, 1981

By Dennis Cox, Stephen P. Signer, Joanne Johnston

A method to assist in the evaluation and selection of roof bolts using in situ measurements of roof bolt loading has been developed by researchers of the Spokane Research Center, National Institute of Occupational Safety and Health. Both axial and bending forces are measured by strain gauges at many locations along the length of fully grouted bolts during various stages of mining. This information is then used to (1) predict bolt loading for variations in bolt spacing, grade, and diameter, (2) calculate the design changes necessary in zones where bending loads are high, and (3) determine if bolt length is adequate. Results from several case studies of full-column bolt loading in coal mine gate roads are used to illustrate the design method. This knowledge will give design engineers a tool for the selection of roof support systems that will improve underground safety by reducing roof bolt failures.

To minimize the equipment operator?s respirable dust exposure in enclosed cabs of mobile equipment by install-ing cab filtration and pressurization systems and by keep-ing doors and windows closed. Background Enclosed cabs are used on mobile equipment to protect operators from health and safety hazards. The primary health concern is overexposure to respirable dust. Examples of such equipment in mining include drills, dozers, haul trucks, and other equipment. When equipment is new, the operator?s dust exposure is normally at acceptable levels. As the equipment ages and gaskets and seals deteriorate, the air quality inside an enclosed cab can reach a point where it is no longer at acceptable levels for the equipment operators. In an effort to improve the air quality in enclosed cabs of older mining equipment, NIOSH has been performing research to retrofit cabs with new filtration and pressurization systems. Over the past few years, this research has shown that retrofit systems can substantially improve the cab?s air quality back to safe and acceptable levels. How-ever, this is only possible when a positive cab pressure is achieved and maintained. Thus, when a cab door or window is opened, the cab pressure drops to zero and the cab filtration and pressurization system is rendered ineffective. During a recent field study, the magnitude of this impact was noted when a drill operator repeatedly opened the cab door throughout the course of the drill cycle. Upon closer examination, it was determined that the cab door was being opened to manually guide the next drill steel into place each time an additional section of steel was needed to drill deeper holes.

Sep 1, 2008

By D. J. Parker

Since the introduction of electricity into the mines of the United States , the hazards incident to the industry have increased materially in both coal and metal mines . For economic reasons the tendency at present , particularly in coal mining , is decidedly toward the adoption of electrical mine machinery , including alternating current machinery , on a more extensive scale than ever before . Obviously, the growing use of such equipment will result in an ever -increasing number of underground transformer stations . The principal electrical hazards in mines are threefold ; fire , explosion, and contact . Of these , fire is the greatest hazard involved in the use of electricity underground , and several fires have originated in underground transformer and motor generator set stations . The fire hazard due to improperly installed and poorly maintained underground transformer stations is an ever-present one , and failure to take the necessariman remedial action is likely to result , sooner or later, in the destruction of life and property . Upon suggesting the necessary corrective measures with respect to such installations , one is often confronted with the statement to the effect that even though this particular hazard has existed over a period of years , there have been no unfavorable results therefrom thus far . Frequently , the desirability for action is not apparent to the mine management until it is too late . Because a mine has a record free from fires , explosions , etc. , over a number of years of operation during which these hazards existed , such good fortune should not be taken as a guarantee that this or any other mine is immune from these common dangers . When the elements of an existing hazard are properly balanced or in the right proportion, the unfortunate combination must of necessity culminate in misfortune of one kind or another. The fire hazard due to underground transformer installations can be very definitely minimized by proper installation and maintenance . In coal mines the transformer banks , connected to 2,300 and occasionally to 4,400 volt circuits , are often found located in open- ended crosscuts , mounted on concrete or timber foundations , and in nonfireproof surroundings .

Jul 1, 1930

By Thomas G. Carnahan

The Bureau of Mines conducted research to simulate in situ leaching of a chalcopyrite ore. The purpose was to obtain a direct comparison between moderate-temperature and elevated-temperature in situ leaching of copper trom minus la-inch ore and to analyze the sulfuric acid and oxygen requirements of the leaching system. Experiments employing oxygen were conducted at 35° and 90° C on 362-and 367-1b ore charges, respectively, under flooded conditions and at 400 psig. At 90° C, 47 pct of the copper was extracted in 913 days of leaching; at 35° C, 27 pct of the copper was extracted in 915 days. Diffusion into and out of the ore fragments con-trolled the rate of leaching. Oxygen consumption was 1.46 lb/lb of copper extracted at 35° C and 3.15 lb/lb of copper extracted at 90° C. Sulfuric acid requirements of the ore were 5.49 and 7.48 lb/lb of copper extracted at 35° and 90° C, respectively.

Jan 1, 1982

Reduce the time, complexity and expense of dissolving metal and mineral samples in solution in preparation for chemical analysis. Approach In earlier research, the Bureau of Mines developed a rapid and inexpensive method for the dissolution of mineral and metal samples in plastic pressure bottles heated in a boiling water bath. Using this technique, samples could be prepared for chemical analysis in less than one hour compared with several hours by traditional dissolution methods (see Technology News No. 85, December 1980 for further details). By heating in a microwave oven, sample dissolution time can be reduced to approximately 5 minutes.

Jan 1, 1983

1.1 Bituminous-Coal and Lignite Dust. - Carboniferous material having a volatile ratio of 12 percent or more by weight and a fineness such that the material passes through a No. 20 sieve. 1.2 Active Underground Workings. - Underground places in which men are required to be or to pass through in the performance of normal mining operations for the production of coal. 1.3 Working Areas. - Underground areas where bituminous coal and lignite are mined, specifically: (a) Face. - The solid surface of the unbroken portion of the coalbed at the advancing end of the working place. (b) Face Area. - The working area inby the last open crosscut in an entry or a room, including the pillar being extracted or longwall being mined. (c) Room. - A place abutting an entry or airway where coal has been mined and extending from the entry or airway to a face. (d) Crosscut (Breakthrough). - Passageways or openings cut through a pillar to connect adjacent entries or rooms. 1.4 Entry. - Underground haulageways, travelways, and airways, except working areas as defined in section 1.3. (a) Active Entry. - An entry in which coal is being mined from a portion thereof or from connected sections. (b) Parallel Entry. - Usually an intake airway parallel to the haulageway. (c) Back Entry. - Usually a return airway parallel to the haulageway.

Jan 1, 1960

Provide an operator cab to assure protection, comfortable use of controls, and good visibility. Approach A cab which raises and lowers by pivoting about d horizontal axis was Installed on two S&S cleanup tractors and tested in two underground working mines. How It Works Hydraulic cylinders actuated by a lever inside the cab cause the cab to pivot about a horizontal axis. This action raises or lowers the cab height. The total cab excursion is 14 inches. A release valve in the hydraulic system allows the cab to lower automatically if struck by a roof load or overhead obstruction. The pivoting action of the cab is engineered so that the operator maintains comfortable use of all controls at all cab heights. The movement is such that the angular relationship of the operator's ankles With the tram and brake foot controls IS consistently within 90 to 100 degrees. Figure 1 outlines the approximate position of the operator at three cab elevations.

Jan 1, 1977

By D. W. Frommer, M. M. Fine

Laboratory investigations have produced flotation concentrates contain- ing 91 to more than 92 percent titania, with fair recoveries, from the Christy property, Hot Spring County, Ark. The titanium-bearing ore on the Christy property occurs in a quartz-clay- iron oxide mineralization, which contains, on the average, about 6.0 percent TiO2, chiefly as the mineral brockite; brookite and rutile are different crys- talline forms of titanium dioxide. Recent work by the Bureau of Mines has shown that titanium chloride can be produced readily from the rutile-type mineral by reduction with coke fol- lowed by low-temperature chlorination. Metallic titanium is in turn derived etallic from the chloride by the Kroll process .

Mar 1, 1952

By Charles L. Kimbell

The series summarizing the prices of the major nonferrous metals on the stock exchanges of the United States and the United Kingdom has been continued this year in tables 23 and 24. Time constraints have prohibited preparation of other price information that has appeared in this study in previous years. Users are urged to consult the 1993 USBM publication Metal Prices in the United States through 1991, which gives an analysis of historical price series and trends, or the 1993 edition of Mineral Commodity Summaries for current U.S. prices on non fuel commodities, and to utilize U.S. Department of Energy sources for information on fuel material costs.

Jan 1, 1993

By Vern L. Kegler

This paper is one off a series dealing with mining methods and costs, sponsored and published by the United States bureau of Mines. ACKNOWLEDGMENTS The author acknowledges the, constructive and helpful suggestions and criticism of W. F. Lamoreaux, vice-president, and general manager of the Ducktown Chemical & Iron Co. United States Geological Survey Professional Paper- 139, by W. H. Emmons and F. B. Laney, has been drawn upon for some of the information contained in the paragraphs or history and geology.

Jan 1, 1931

Hang ventilating air curtains so that they can be installed, moved, opened and closed more easily than curtains that are spadded or nailed in place. Approach Low-leakage plastic curtains fitted with grommets along the top were threaded onto a steel cable which is suspended from roof bolt plates. The system was tested in two mines. How It Works The curtains are threaded onto a steel cable which is suspended from roof bolt plates by S-shaped hooks. See Figure 1. The outby end of the cable is reeled off a hand operated winch; the inby end of the cable is anchored to a roof bolt plate by means of a cable grip and an S-shaped hook. To install the curtains the following procedure is used. First, the winch is located at least 5 feet outby the last open cross-cut. The base of the winch can be secured to the mine roof with short roof bolts, only about a foot long.

Jan 1, 1978

By W. A. Calhoun

A method for concentration of the nickel-cobalt-bearing mineral, siegenite, from a table middling has been developed by the Bureau of Mines at Rolla, Mo. The table middling is composed of a complex series of sulfide minerals, occurring in mill operations in the southeast Missouri "lead belt." In these operations the siegenite is lost as a separate concentrate, being diverted to other products. The procedure also includes recovering commercial-grade concentrates of copper and lead. A low-grade zinc concentrate, a potential coproduct, was also made.

Jan 1, 1962

By G. Molinda, D. Dolinar

Each year, about 2,000 falls of supported roof occur in the more than 800 underground U.S. coal mines. Therefore to help improve the design of primary support systems, the National Institute for Occupational Safety and Health (NIOSH) conducted a nationwide study of roof falls in over 2,500 km of roadways at 37 coal mines. Information on the roof falls as well as other geotechnical, mining, geologic and roof bolting factors were collected and quantified Then a multi variate statistical analysis was conducted on the data with the roof fall rate being the outcome variable The results were used to derive preliminary design guidelines for predicting the roof bolt length, capacity, and pattern required to effectively reduce the roof fall rate. The equations are fairly limited by a relatively high statistical variance in the data. Also reported is a recent survey of U.S roof bolt manufacturers that shows a significant change in bolt types used over the last ten years.

Reduce potential for steering errors during tramming of articulated vehicles, particularly when the operator is seated to the rear of the machine pivot point and is tramming in reverse. Approach Position-sensing and feedback cylinders were applied to the steering cylinders of two S&S cleanup tractors to cause the steering-control lever to match the orientation of the vehicle sections. The vehicles were tested in two working mines. How It Works A position-sensing cylinder (see Figure 1, Item A) is attached to one of the steering cylinders in the cleanup tractor steering system. As the steering cylinder piston rod is actuated by movement of the control lever, hydraulic oil flows from the position sensing cylinder to the feedbck-cylinder (B), causing the feedback-cylinder piston and rod to move. The outside end of the rod repositions the the steering-control lever until its angular position corresponds to the orientation of the vehicle sections.

Jan 1, 1978

By J. J. Demeter

A tube-wall reactor with a Raney nickel catalyst deposited on the outer wall of the tube by flame spraying is effective in the practically complete conversion of 3H2+1CO synthesis gas to a high-Btu gas (methane) at an hourly space velocity of 7,000 volumes of gas (NTP) per hour per volume of annular volume. Partially reacted synthesis gas containing an appreciable amount of methane can also be treated in this reactor to increase the heating value to over 900 Btu per cubic foot. Excellent heat removal through the metal wall to a coolant and temperature control were obtained. The heat transfer co-efficient from the catalyst to the coolant was about 275 Btu per hour per square foot per ° F. Synthesis tests were conducted with tubes 1.2 inches in ad by 6 inches long, and 1.3 inches in od by 36 inches long. When operating at a synthesis gas rate of 100 to 120 scfh per square foot of catalyst-coated tube, catalyst life was long enough to realize a catalyst cost for the raw Raney nickel alloy of about 0.3 cent per 1,000 cubic feet of pipeline gas (900 to 950 Btu per scf). Gas recycling at ratios of 1:1 to 3:1 was effective in increasing conversion and in extending the life of the catalyst to about 16 weeks. In cost and in operating characteristics the tube-wall reactor compares favorably with the fluidized-bed and hot-gas-recycle reactor systems for the synthesis of high-Btu gas from H2+CO.

Jan 1, 1967

By Edward F. Divers

This Bureau of Mines report describes the results of a program to develop small, rugged scrubbers with high dust collection efficiency for use in under-ground coal mines. The Bureau's Pittsburgh (Pa.) Research Center has developed and assisted in the development of several types of improved scrubbers that are especially suitable for various underground mining applications. Research efforts concentrated on reducing the size, power, and water consumption of these scrubbers, while optimizing their dust collection efficiency. Fractional dust collection efficiency, air volumetric range, size, power, water consumption, and application guidelines for each type are described. Air pressure differentials ranged between 2-and 3D-inches water column (wc). The dust collection efficiency of six scrubbers--a venturi, two flooded-fibrous-bed, a venturi-impaction plate, a wetted-fan, and a rotating flooded-bed--were compared. The rotating flooded-fibrous-bed and the stationary flooded-fibrous-bed scrubbers showed the highest coal dust collection efficiency. Test results show that these scrubbers can generally achieve respirable size coal dust collection efficiencies in the high 90-pct range required to reduce both long-(8-hour) and short-term coal mine dust concentrations below Federal requirements.

Jan 1, 1979