Search Documents

By Ernest E. Fairbanks

[Microscopic methods have proved to be valuable assets in the study of low-grade ores. While the chemical assay u a ally discloses tine total content of valuable metals in such an ore, a thorough knowledge of the nature of the ore should form the from which to prepare an efficient means of recovery. In the treatment of low-grade ores, inefficient recovery, as indicated bay the amount of valuable mineral permitted to go to waste in the tailings, is too frequently the rule rather than the exception, As methods of recovery become more efficient, many low-grade 10 mineral A posits suddenly assume o commercial significance, In much of this material the minerals are so finely disseminated and intermixed that identification even by microscopic methods is a difficult matter. The application of microchemical qualitative analysis with the aid of new device described in this paper, will solve many of the problems of identification encountered in the study of low-grade potential ores. In these ores, especially, the limitations of ordinary microscopic methods are liable to become very great. The microchemical tests obtained by applying a standard set of reagents to a polished knoting whether or not a tarnishing action develops, have considerable value but arc far from being infallible. It is well-known that electrolytic effects are apt to affect seriously the diagnostic value of the tests, end this effect is encountered much more frequently in dealing with finely desseminated minerals. resort to microchemical qualitative analysis, therefore, becomes indispensable.]

Jan 1, 1924

By J. F. Barkley

"In the course of the Government's Fuel Economy Survey of its own power plants, studies and tests have been made of various oil-burning equipments under power-plant boilers. There are now many types of burners being offered in the relatively limited field of power-plant use. The majority of the types used may be grouped into two general classes- those using steam to effect the atomizing of the oil, and those using mechanical means.Burners using steam have had the most prominence in this field for a long period. The mechanical atomizing type of burner successfully applied on shipboard, however, pointed to a possible betterment in land work. The vision presented itself of a burner that would need no steam for atomizing that would permit of air inlets or registers compactly arranged as a part of the entire burner, and that would only require the natural stack draft usually available in land boiler furnaces. Hence, rather recently there has been much development along this line, resulting in various types of burners.In Table 1 are grouped test items chosen from many tests showing representative analyses of the products of combustion obtained with various burners installed in various types of furnaces. In all these tests the burners were handled by experts and represent practically the best attainable for that particular arrangement. The boiler efficiencies ranged from 70% to 80%. It will be noted that the burners using steam for atomizing were able to secure slightly better 002 and less 02 without the presence of CO."

Feb 1, 1926

By W. C. Phalen

"The term ""manjak"" is applied to a variety of bitumen or solid hydrocarbon occuring on the Island of Barbados, West Indies, and in Utah, Cuba, and Trinidad. The deposits on the latter island are found within a distance of three miles of San Fernando, the second largest town on the Island, and within three miles of the famous asphalt lake.In chemical composition, manjak is like asphalt. It is almost pure bitumen. Its melting point is, however, more than 4000F. whereas asphalt melts at 1000F. In composition, it consists of 80 to 90 per cent carbon, the balance being chief¬ly hydrogen, with a small quantity of sulfur. It resembles coal in appearance, is odorless, hard, and brittle. It is found in thin beds between layers of clay.The island of Trinidad is rich in this mineral resource. Its development has as yet hardly begun, and the exportations already made have been with the view of testing out the ma-terial. During 1918, exports to the United States were valued at about $3100, and in 1919, up to October 1, they totaled 41 tons, valued at $1900. Prior to 1900, manjak was mined on a small scale in Trinidad, but for various reasons, very little was done between 1900 and 1913. In the latter year, mining operations were resumed by the Trinidad-Tarouba Oil Development Company, of San Fernando. At the present time, there are five shafts, one of which has reached a 37 foot bed of manjak at a depth of 400 feet. Operations could be greatly extended if there were a greater demand for the material.It has not been found profitable to export manjak from Trinidad in the crude state as the price received, namely $35 per ton, hardly covers mining expenses. These are increased by the necessity for careful and thoro timbering on account of the clay formation.Compounds, made by combining manjak with mineral oil command fair local prices which have enabled mine operations to proceed at a profit. Experimentation is still in progress with different mixtures of manjak and oil for various purposes. The manjak, recently sent to the United States was for the purpose of ascertaining whether American oils would be more economical and useful for mixing with the manjak than the Trini¬dad oils. It is the plan to erect a plant very soon for the manufacture of a variety of manjak paints and compounds.Manjak is rapidly increasing in use, particularly in connection with the oil industry. It is produced in close proximity to the oil wells in Trinidad. It is boiled with oils at high temperatures and converted into compounds and paints for nearly every purpose where a preservative is needed, for example, on pipe lines, boilers, chimneys, and miscellaneous iron ware, machinery, etc. It is usually applied in the liquid state, hardening into a tough, rubberlike coating. It has low viscosity, and is not affected by ordinary heat. It makes an excellent insulating material and is impervious to both air and water. In hot and damp climates, like that of Trinidad where pipe lines quickly deteriorate, their life has been pro-longed for extended periods when painted with this material."

Nov 1, 1919

By J. Hudy

An investigation has been made to determine the applicability of the Cendrex3 X-ray instrument for the measurement of the ash content of washed bituminous coal products. The results obtained for selected products from six preparation plants in the Appalachian region and one preparation plant in the mid-western region are described. Emphasis of the study was placed on low-ash bituminous coal products suitable for utility or metallurgical markets. There was good agreement between the results obtained by conventional ash determination methods and by ash determination using the Cendrex for all products tested.

Jan 1, 1968

By E. J. Kloos

The Bureau of Mines evaluated all previously approved gas masks to determine their ability to provide respiratory protection against each of the following six selected amines: ethylenediamine, diethylamine, n-butylamine, ethylamine, methylamine, and hydrazine. Minimum requirements were a 24-minute service life at a flow rate of 64 liters per minute (32 liters per minute for hydrazine) and an amine concentration of 1.0 volume-percent (0.5 volume-percent for hydrazine). The three masks meeting these requirements were the LG4, Willson Products Division, The Electric Storage Battery Co.; the GMD-SS, Mine Safety Appliances Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

6. Development of Mine Sealant Material Systems 6. 1 Introduction The preliminary evaluation of material systems described in Section 3 led to the selection of the following four promising systems for further development: System A: Aggregate, Fly Ash System System B: Aggregate, Fly Ash, Urethane Foam System System C: Aggregate, Bulkhead, Light Expansive Concrete System D: Aggregate, Self-Supporting Thick Slurry Preliminary laboratory tests indicated that the building of effective bulkheads from one borehole would be extremely difficult. Two extra boreholes would be required adding to the overall cost of the system and making the system less attractive. Tests with light expansive concrete showed that bulkheads would be required, the material would not support itself. As a result, further development of this system was terminated. Foam concrete was selected as the most suitable material to be developed into a self-supporting, rapid-setting slurry. A laboratory investigation of its use for mine sealing was conducted during this program; the results are summarized in Section 6. 5 and details of the laboratory program are presented in Appendix B.

Jan 1, 1973

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX B - DEVELOPMENT OF FOAM-CONCRETE SLURRY MINE SEALANT 1. Introduction This appendix describes the results of an experimental development and laboratory evaluation of foam-concrete as a rapid setting, lightweight, self-supporting mine sealant material. Foam concrete, otherwise known as Aerated Concrete, is a form of lightweight concrete whose structure consists of air bubbles held together by a hardened cement mortar. Its principal applications are found in roofing, insulation, shock absorbing, and backfill. The air bubbles in foam concrete are formed either by chemical reaction in the wet, placed mortar, or by introducing a stable foam into the mortar during mixing. The mortar is usually a cement slurry with fine sand or fly ash as filler. Our attention focused on preformed foam concrete, since this is most adaptable to field applications. Equipment is available,* which simultaneously mixes and pumps a slurry of foam concrete. Such a slurry can be produced at a rate of up to 50 yards/hr and has been pumped in a 2-inch-diameter hose 1000-feet horizontally and 250 feet vertically up without significant bubble deterioration. One very attractive feature associated with the use of foam concrete concerns site logistics. Foam concrete can be generated with densities as low as 20 lbs/ft3, and hence the total number of

Jan 1, 1973

By David P. Lindroth

The heat content above 25.0° C up to 1,000° C was measured for six rock types: St. Cloud Gray Granodiorite, Holston Limestone, Sioux Quartzite, Rockville Quartz Monzonite, Salem Limestone, and the basalt at Dresser, Wis. The calorimetric data were obtained with an isothermal jacket-copper block calorimeter. The experimental heat content data for each rock type are presented, along with specific heat data obtained from the temperature derivative of the heat content. For the six rock types the maximum deviations of the specific heats at a given temperature were within 10 percent below 575° C and within 34 percent above 5750°C. The increase in the values of specific heat range from a minimum of 13 percent for the basalt at Dresser, Wis. (temperature range, 100° to 1,000° C) to a maximum of 46 percent for Holston Limestone (temperature range, 100° to 870° C).

Jan 1, 1971

By H. H. Schrenk

The Bureau of Mines midget impinger dust-sampling apparatus was described first in 1937.4/ Two supplementary reports5/6 were published in 1938. These reports are now out of print. The material published previously is combined in this paper to make information on this device available for distribution. The impinger was developed by the Bureau of Mines in cooperation with the United States Public Health Service in 1922. The underlying principle of this instruments is based on impingement land wetting, of the dust particles by drawing air through a nozzle at high velocity onto a smooth surface under a bubbling column of liquid. The dust particles are retained in the liquid. The apparatus has been used widely and permissible limits of dustiness have teen established in the United States on the basis of results obtained with this device in correlation with medical studies. However, it has been criticized for its bulk, weight, and power requirements.

Jan 1, 1939

By W. D. Bensema, J. W. Adams

A portable, multichannel battery-operated mine-permissible measurement system was developed to measure the rms magnetic-field noise spectrum in the frequency range from 100 Hz to 375 kHz. During each measurement, the entire spectrum is measured simultaneously through the use of time-domain recordings which are later analyzed by Fast Fourier Transform processing. Dynamic ranges of 60 dB in a 125 Hz bandwidth are obtained for spectra covering the range from 100 Hz to 100 kHz. The method also allows a three-dimensional display of the way spectrum occupancy changes with time. Calibration and correction procedures allow absolute field strength measurement with an uncertainty of not more than 3 dB. We feel that further analysis of the system errors will allow this uncertainty to be reduced to less than 1 dB. Ambient magnetic field noise spectra covering frequencies from 100 Hz to 100 kHz are given for several underground coal mine locations. Examples are also given of magnetic field noise on the surface above the mine, noise in the mine face area, noise radiated by specific equipment, the voltage spectrum found on a 600 V dc trolley wire, and noise picked up simultaneously on loops and on roof support bolts.

Jan 1, 1973

By David C. Oyler, Herbert H. Fields, William P. Diamond

A 3-inch pilot hole was directionally drilled to intercept the Freeport coalbed horizon horizontally at Mather, Pa., as part of a Bureau of Mines degasification project. The original concept was to continue the horizontal drilling into the coalbed, after the initial intercept, with a total of three horizontal holes eventually being completed. However, the erratic thickness (0.0 to 4.3 feet) of the Freeport coalbed at Mather was not sufficient to sup- port the horizontal drilling degasification technique, and the site was abandoned after six attempts to locate adequate continuous coal thicknesses. The drilling of coreholes in the immediate vicinity of proposed well paths to evaluate coal thickness is essential prior to future slant hole operations. Although mechanical failures of the new directional drilling equipment, mud pump and rig breakdowns, directional control problems, and exploratory horizontal drilling in the Freeport horizon more than doubled the anticipated cost of the pilot hole, continuing improvements in directional drilling equipment and techniques should significantly reduce the time and costs of future drilling operations.

Jan 1, 1977

By E. J. Kloos

The Bureau of Mines evaluated all previously approved gas masks to determine their ability to provide respiratory protection against each of the following six selected amines: ethylenediamine, diethylamine, n-butylamine, ethylamine, methylamine, and hydrazine. Minimum requirements were a 24-minute service life at a flow rate of 64 liters per minute (32 liters per minute for hydrazine) and an amine concentration of 1.0 volume-percent (0.5 volume- percent for hydrazine). The three masks meeting these requirements were the LG4, Willson Products Division, The Electric Storage Battery Co.; the GMD-SS, Mine Safety Appliances Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

By Isaac A. Zlochower, Michael J. Sapko, Ronald S. Conti

This paper describes a U.S. Bureau of Mines investigation of large-scale coal dust explosions in an experimental mine using a high speed electro pneumatic mechanism for the rapid grab-sampling of gases and dusts. This technique enables the monitoring of pyrolysis and charring in fuel dust particles, and the collection of gaseous combustion products, in both large and small-scale explosions. Data obtained from full-scale dust explosion tests at the Bureau of Mines Lake Lynn Test facility show the following: Rapid sampling appears to "freeze" the burned gas compositions at the flame temperature values. Gas samples taken entirely in the flame zone consist of pyrolysis and combustion products with very low residual oxygen. The particles collected in the flame zone show signs of extensive pyrolysis and charring. Measurements of gas concentrations and particle flame temperatures suggest that char burning may have occurred in the flame zone.

By Gary R. Gavan

This report presents the documentation and User's Manual for a data retrieval and report generation computer program. The program operates on a data base containing over 19,000 pieces of coal mine equipment in use in 1976.

Jan 1, 1979

By R. E. Collom

The spontaneous explosion of charges of nitroglycerin placed in deep wells situated in parts of the Ranger and Caddo fields of North Texas has aroused considerable inquiry among operators end others as to the probable agency, or combination of conditions, which causes the explosion.The method now followed, under certain physical conditions of a well, of setting a charge of nitroglycerin and allowing it to explode spontaneously was discovered locally by accident. In certain deep wells where formations, overlying productive strata, cave upon withdrawal of casing, it has been the practice to fire the shot electrically. In some of these operations the electric wires are broken or the firing system is otherwise deranged by pulling casing or the caving of hole prior to the time for firing. Sucn accidents make it necessary for the driller carefully to clean cavings out of the hole to a depth close to the top of the charge, after which in the normal practice, an attempt is made to fire the charge by dropping a ""jack-squib"", fitted with a fuse and detonator, down the well. Mr. R. L, Fowler, production manager for the Pierce Oil Corporation, reports that a delayed shot was thus successfully tired through four feet of caved material lying on top of the nitroglycerin shells.When a shot destined to be fired electrically fails, because of the above mentioned accidental conditions to the electric firing system, much time is required for the driller to run casing into the hole and clean out caved material. It was during the time of such uncompleted operations that the spontaneous explosions first noted took place. Having noted these spontaneous explosions the well shooters now intentionally place a charge in deep holes, which because of probable caves would otherwise have to be tired electrically, and wait for the charge to go off. No detonators are placed with the charge.

May 1, 1920

By W. P. Yant, R. R. Sayers

The rather sudden increase in the use of methanol as an antifreeze for automobile radiators has caused considerable comment , with some anxiety to persons interested in industrial and public health , regarding the possible health hazard in dispensing and using the product . In view of this , the chemical industry interested in the manufacture and marketing of methanol requested the Bureau of Mines to make an impartial and extensive investigation of the hazard involved . With the assistance of the industry this investigation is now in progress and will extend throughout the present winter . When these observations are finished a complete report will be made . At present , however , the acute interest in the problem and the many inquiries that have been received from manufacturers of methanol , garage owners , the automotive industry , public health officials , and private persons demands a brief statement relative to the reasons for the recent availability of methanol for antifreeze purposes , the plan of the bureau's investigation , and the trend of the results of the investigation obtained to date .

Dec 1, 1930

By Henry W. Busch

Determination of the aldehyde content of Diesel-engine exhaust gas has proved rather cumbersome and unsatisfactory when carried out in its entirety in field investigations; therefore, studies were conducted with a view to developing methods by which samples might be collected in the field and trans-ported to the laboratory for analysis. Experience also indicated that aldehyde samples collected in water solution and then transported to the laboratory sometimes underwent serious changes in composition if several days elapsed between sampling and analysis. Polymerization of the aldehydes, which takes place readily in dilute aqueous solutions, may have been the cause of such changes. Because of these difficulties, experiments were conducted to find a suitable stabilizer or preservative for dilute aqueous solutions of the aldehydes that occur in Diesel-engine exhaust gas, so that in field studies a known volume of gaseous sample might be collected and brought into contact with water, and the resulting solution of aldehydes analyzed in the laboratory at some later time with reasonable certainty that the results would represent the composition of the original sample,

Jan 1, 1949

By C. P. Lazzara, R. A. Franks, G. F. Friel, J. C. Edwards, J. J. Opferman

A National Institute for Occupational Safety and Health’s (NIOSH) mine fire detection re-search project was undertaken to evaluate multiple mine fire sensor types for nuisance alarm discrimination. The response of multiple fire sensor types to three small coal fire and three small conveyor belt fires in the presence of diesel emissions was evaluated in NIOSH’s Pittsburgh Research Laboratory (PRL) Safety Re-search Coal Mine (SRCM). An array of fire sensors which included an optical and ionization smoke sensor, a chemical cell CO sensor, and Metal Oxide Semiconductor (MOS) sensors, was used to sample the diesel engine and fire source emissions. The mine fire detection experiments demonstrated the ability of a MOS sensor with a bimodal response to NOx and products-of-combustion (POC) to respond to the onset of smoldering combustion in the presence of CO and POC particulates from a diesel locomotive. As part of an in-mine evaluation in an operating coal mine, the MOS NOx responsive sensor and an ionization smoke sensor was demonstrated as a method to discriminate diesel emissions and cross-interference of H2 on a CO chemical cell fire sensor at a battery charging station. The reinforcement of mine fire sensor information with the use of multiple sensor types, such as an MOS sensor and ionization and optical smoke sensors, is shown to be important for nuisance alarm discrimination and early mine fire detection.

By F. W. Hoertel

The Bureau of Mines investigated the use of depleted uranium as a sacrificial anode for the cathodic protection of submerged and underground structures of iron , steel , and copper . Uranium-metal couples were tested in simulated marine environments of varying oxygen contents at pH values between 5.5 and 8.5 and under simulated boiler service condition in Rolla , Mo. , city water . Similar couples were tested in samples of Missouri soils to simulate underground service . Uranium remained anodic to iron , steel , and copper in the simulated marine environments and under simulated boiler service if the electrolyte was oxygen- free city water . Uranium appeared to offer limited protection to iron , low- carbon steel , stainless steel , copper , and zinc in the simulated underground tests . Uranium anodes offer a space advantage because 1 cubic inch of uranium gives approximately the same protection as 2 cubic inches of magnesium or 1-1 /2 cubic inches of zinc .

Jan 1, 1963

By B. W. Jong

As part of the Bureau of Mines program to develop substitute or improved performance refractory materials for metallurgical applications, the Tuscaloosa Research Center has evaluated the effect of additives on sintering and strength properties of aialon (silicon aluminum oxynitride) compositions fabricated by a conventional powder metallurgy technique. Additions of Y203, Gd203, CeO2, MgO, ZrO2, ZrSiO4, and MgA12O4 to a sialon composition containing 70 pct ß-Si3N4 + 30 pct a-A1203 increased sintered densities by as much as 50 pct over densities of undoped material. The studies also indicated that sintered densities reached a maximum between 20 and 30 mole-pct a-A1203 when a series of sialon compositions of a-Si3N4, having 6.7 to 57.9 pet a-Al203, were doped with Y203, Gd2O3, and MgO. In studies to establish the effect of the crystalline phase of the silicon nitride and alumina used, tests were made using a- and ß-Si3N4 and a- and ?-A12 03 as starting materials. The tests indicated that when using an addition of 5 wt-pct Y203, best results were obtained with a sialon composed of 74.4 mole-pct a-Si304 and 25.6 mole-pct ?-A1203. In other tests made with this sialon composition MOR values of 28,120 and 29,500 psi at 25° C, and 23,520 and 16,850 psi at 1,400° C, were obtained when doping with 5 wt-pct ZrSiO4 and ZrO2, respectively.

Jan 1, 1980