Search Documents

By Kenneth M. Earl

This report describes the results of a field study conducted by the Bureau of Mines during 1956 and 1957 on manganese-and iron-bearing mineral deposits in the southern district of Aroostook County, Maine. The work was undertaken to determine the extent of deposits largely concealed under glacial drift and to obtain subsurface samples for manganese mineral identification and research in ore dressing and extractive metallurgy. The investigation was confined to the Westford Hill-Daggett Hill area in Hodgdon Township and to the Stewart prospects and vicinity in Linneus Township. Over 50 magnetic anomalies were mapped by magnetometric surveys in the Westford Hill-Daggett Hill area, Hodgdon Township. The largest anomaly, as outlined by the 1,000-gamma contour, indicates a deposit 3,200 feet long with a maximum width of 350 feet. The smallest anomaly measures about 10 feet wide by 25 feet long.

Jan 1, 1962

By J. Hyvarinen, A. D. Look

"INTRODUCTION AND SUMMARYElectricity is used extensively in open-pit metal mines to provide illumination, heat, and power to operate hauling and loading equipment, drills, pumps, signal systems, and other machinery. Good installation and maintenance of equipment and power, circuits, are essential to minimize the hazards of shock, burns, and fire.In the 13 years from 1931 to 1943, 20 fatal and 82 nonfatal injuries resulted from the use of electricity in open-pit mines in the United States ; 4/ these figures represent about, 10 percent of all fatalities and 1 percent of the nonfatal injuries. The ratio of fatal to nonfatal injuries from electricity in such mines was very high during this period; the figures show one fatality to every five accidents from this cause.Electricity may cause personal injury through abnormalities in equipment, such as short-circuit, accidental ground, overload, and poor contact; however, each year some fatal electrical accidents are due to persons touching uninsulated ""live wires."" These contact injuries are the result of careless body movements of persons in the vicinity of 'wires at places not normally frequented, or of accidental contact with live circuits when handling metal objects. Electrical hazards can be minimized by the enclosure or elevation of current-carrying parts; ample working space around equipment, adequate insulation, locking switches in the open or closed position under certain conditions, identifying and warning devices, protective grounding, insulating flooring, platforms, or rubber gloves, and proper inspection and maintenance."

Apr 1, 1949

By R. J. Bielicki

A sorption apparatus for measuring the equilibrium sorption isotherm and the rate of diffusion of methane from fine-sized coal was designed and constructed. Preliminary work that used Pittsburgh and Pocahontas No. 3 coal shows that the diffusion coefficient varies with pressure and that the fracture spacing in these two coals is substantially different.

Jan 1, 1972

By Arden D. Fugate

The Federal Bureau of Mines conducted extensive studies on solid-state defluorination (laboratory scale) and tests on molten defluorination (intermediate scale) of siliceous fluorspars. The studies were made to develop a pyrohydrolytic process for liberating fluorine from offgrade fluorspars. Test results showed that more than 90 percent of the fluorine can be evolved by solid-state defluorination at 1,300° C., and more than 97 percent can be liberated by molten-state defluorination at 1,420° C. Solid-state defluorination conditions were established by conducting tests on mixtures of ceramic-grade fluorspars and high-purity silica flour. Pelletized mixtures were defluorinated under varying conditions of time, temperature, and relative concentrations of silica, calcium fluoride, and water. The effects of adding various amounts and combinations of aluminum oxide and iron oxide on defluorination were also studied. Investigations of solid-state defluorination indicates that the following two reactions are involved: 2CaF2 + 3SiO2 = 2CaSiO3 + SiF4, and CaF2 + Sio2 + H20 = CaSiO3 + 2HF, The second reaction is dominant, although significant defluorination can be achieved by the first reaction.

Jan 1, 1961

By G. L. Gates

The Bureau of Mines in cooperation with the City of Long Beach) Calif.) studied some physical factors effecting the deposition of barium sulfate scale in oil-well rotary pumps. Freshly formed barium sulfate was obtained by combining sulfate in sea water with barium from a barium chloride solution. The rate of scale deposition was measured quantitatively by weighing the pump impellers and diffusers. The results of the tests showed that coating the impellers with plastic significantly reduced the rate of barium sulfate deposition.

Jan 1, 1967

By G. E. McElroy

"while investigating the presence of heavy strata gases* in certain mines of the East Tintic mining district of Utah, a small, local body of light, very hot gas of high-nitrogen composition was noted in one of the mines. Observations and analyses indicate that this light gas was resulting from very rapid oxidation of finely disseminated pyrite, in lead-silver sulphide ore. The gas was actually mine air which had lost a large proportion of its oxygen content by reaction with the pyrite. This body of gas was hanging in a local high spot about 5 by 5 by 5 feet in size, caused by caving, at the end of a crosscut. Fifty feet from this spot, an air current of 6000 cubic feet per minute was entering the 5 by 7 foot cross-cat from a raise from below.On account of the vapor contained in the gas, the bottom level of the gas could be plainly seen and was practically a horizontal plane, but of slightly wavy appearance, coinciding with the point where an acetylene light was extinguished. This body of gas was visited on three occasions and samples obtained by means of evacaated bulbs and by water displacement. The temperature of the gas was ap¬proximately 175 degrees P. on all three occasions, so that sampling required thick gloves and quick action. Air three feet below the vapor line had a temperature of only 120 degrees F., and a relative humidity of 27 per cent. The stratification of the air and gas mixtures was so sharply defined that the sampler could hold his head a few inches below the vapor level for an appreciable period of time without any noticeable effect other than that due to the high temperature. At one foot below vapor level, it was 135 degrees F., and the relative humidity was 30 per cent. When a candle and an acetylene light were raised into the gas from below, the candle flame was extinguished at a point two inches lower than the acetylene flume, indicating a drop in oxygen content from about 16 per cent to 12 per cent (oxygen content of normal dry air 20.05 per cent) in the distance of two inches."

Sep 1, 1921

By Daryl R. Tweeton

The Bureau of Mines compared the effects of surface-active chemicals with those of pure water on core-drilling rock and quartz and on fracturing quartz. The objectives were to determine if these chemicals assist drilling and fracturing rock and if zeta potential control was worth pursuing as an aid to full-scale drilling. All tests were performed in the laboratory. No significant increases in drilling rates were observed for 1 to 10,000 ppm Al (as AlC13) in flushing water when drilling microcline or serpentine, nor for 1 to 10,000 ppm Mg (as MgC12) when drilling microcline or marble. Concentrations near those giving a zero zeta potential were used with microcline and marble. A 50-pct rate increase was observed for drilling quartz in 0.7 ppm oleylammonium acetate, which gave a zero zeta potential. No other concentrations were used. No effect on the tensile strength of quartz thread in 0.05 ppm Al (as AlC13), which gave a zero zeta potential, was observed. Heptanol, reported to give a zero zeta potential on quartz, did not reduce the bending strength of small quartz bars below that in water. These generally negative findings raise doubt about the usefulness of zeta potential control in full-scale drilling. The results, combined with previous studies, suggest that controlling physical properties of drilling fluids, such as viscosity, is more useful than altering chemical properties.

Jan 1, 1976

By Harry D. Jumper

This paper describing the methods of ruining a sand, gravel, and bowlder deposit 20 miles east of Los Angeles, and the classification and preparation of these materials for market, is one of a series being prepared for and published by the United States Bureau of Mines on methods and cost of mining sand and gravel. These papers are designed to disseminate technical information regarding, the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion anti study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations stall ensue. The description contained herein is typical of this industry in Southern California. ACKNOWLEDGMENT The author acknowledges tine assistance of L. L. Rogers, vice-president and manager of production and distribution for the Consolidated Rock Products Co., in the preparation of this paper.

Jan 1, 1933

By Pedro Lilienfeld

The objective of this program was the development, design, and fabrication of six personal-sized completely self-contained dust monitors capable of real-time as well as time-averaged monitoring of the concentration of respirable particles in coal mines, in the range of 0.1 to 100 mg/m3. The operation of these monitors is based on light scattering and passive air sampling. The design stressed overall miniaturization, ruggedness, simplicity and versatility. These instruments incorporate a single-chip CMOS microprocessor to perform all signal processing, data display and storage, and timing functions. The overall dimensions of these devices are, approximately, 10 by 10 by 5 cm.

Jan 1, 1982

By B. K. Shibler

As a part of the Bureau of Mines' intensive; 'investigation of domestic manganese deposits, ore-dressing studies were conducted on three samples of oxide and silicate manganese ores from various Wyoming properties. The samples wore as follows: 1. A 2-ton sample of ore was obtained by a Bureau engineer during examination of the Caulkins-McGuckin property in the center of Crook County, 10 miles north of Sundance, Wyo. The ore body was described as a vein deposit in rhyolite porphyry. 2. The J. B. C. Mining Co. submitted a 1-ton sample of oxide manganese ore from a property located 44 miles northeast of Rock River in Albany County, Wyoming. 3. A 1-ton sample of oxide-silicate-ore was obtained by a Bureau examining engineer from the Gheen property in the northeast corner of Washakie County, Wyo. The ore body was described as a replacement deposit in a country rock of silicified limestone. As the samples differed widely in physical and chemical characteristics and also in their response to methods of concentration, ore from each property was considered a separate ore-dressing problem.

Jan 1, 1949

By Joseph A. DeCarlo

For the first time the Bureau of Mines is combining, in one report, comprehensive tabulations on both beehive and slot-type ovens. This publication presents statistical data on the number and capacity of all such coke ovens in the United States on December 31, 1957. Combining data on both types of ovens should prove helpful to those interested in keeping abreast of the latest changes in carbonizing capacity, particularly since the coke has similar properties and uses. Annual reports furnished to the Bureau of Mines by coke-oven operators shared that 78 oven-coke plants were operating in 22 States on December 31, 1957. This was a decline of one plant from December 31, 1956, as the Republic Steel Corp. took the ovens at Canton, Ohio, out of production on December 17, 1957, for dismantling and rebuilding in 1958. Total oven-coke capacity was 80,299,400 tons in 1957.

Jan 1, 1958

By S. J. Page, P. Bolsaitls, W. E. Wallace, C. A. Hill, M. J. Keane

"Boiling respirable quartz dust in water for 10 to 40 minutes decreases the cytotoxicity for both erythrocyte hemolytic potential and pulmonary macrophage release of lactate dehydrogenase in vitro. The potential is reduced to near zero in the boiling concentration range of 1 to 10 mg quartz per ml water in boiling times of 20 to 40 minutes. Below this range the detoxification occurs over a longer boiling time. Above this range the hemolytic potential remaining after 40 minutes of boiling approaches native quartz potential with increasing concentration up to 30 mg quartz per ml water. Replacing the media with fresh at the midpoint of boiling results in full detoxification through 20 mg per ml. Pre—boiling the medium with quartz or silica gel reduces the effect of subsequently boiling test samples. Detoxification persists after mild drying at 110 C for 8 hours, and persists after three days of resuspension in water at room temperature. Additional data on persistence of the effect, on the use of acidic and basic media treatment, and on surface analyses are presented, with a discussion of a working hypothesis and research needs.IntroductionResearch underway to determine interactions of quarts and other mineral dust surfaces with pulmonary fluids and alveolar macrophages in culture led to the observation that when dusts were autoclaved in aqueous suspension, their cytotoxic effects on macrophages wore suppressed, in some cases fully and even after several days incubation with the cells. This finding was in direct contradiction to earlier results from both short term macrophage lysosaal enzyme release assays, as well as longer term cytotoxicity assays from macrophages in culture; in those studies, dusts were steam autoclaved at 121 121 ºC with no liquid water but with steam present. (1,2) However detoxification under boiling conditions has been reported in other research.(3). It was decided to use the hemolysis assay to further investigate these findings, because of its sensitivity, simplicity and cost."

Jan 1, 1988

By Carl R. Peterson

The Rapidex continuous spiral blast tunneling concept uses a spiral blast pattern that provides efficient slabbing action, continuous progression, and partial self-shielding. A lightly shielded tunneling machine using this concept stays at the face to provide continuous drill, load, shoot, and muck functions. Previous phases proved the effectiveness of the blast pattern in the White Pine Shale tested the design features of the shield and developed a remote loading and shooting capability using inductively initiated blasting caps and a pumpable slurry explosive. Phase IV assembled previously used front-end elements (drill, loading components, shield) on a used Joy loader chassis and added a mucking system television monitoring and remote control elements. Remote television monitored loading shooting and mucking were investigated. Difficulty was experienced in locating previously drilled blastholes near the bottom of the heading and even on the face. These holes often had to be considered as lost. Because of hydraulic system deficiencies and overall congestion of machine elements at the face mucking rates obtainable with remote television monitoring were low (on the order of 16 tons per hour). Performance was good enough to indicate improved rates if more space were available and if extreme thoroughness were not required. Because of the serious nature of the lost hole problem, a new explosive loading scheme was given a preliminary evaluation. The new scheme would require the explosive and the detonating charge to be loaded through the drill steel. If the necessary equipment modifications could he made and if safe, efficient operation were assured, the new scheme would alleviate some of the crowding at the face and would eliminate the lost hole problem.

Jan 1, 1978

By John Ward Smith

The potential economic value of oil shale depends on the products from thermal degradation of the rock, because no other practical method for producing valuable material from oil shale has been found. Detailed study of thermal degradation behavior can aid in characterizing oil shales and their deposits and in evaluating oil-shale processing methods, Numerous publications describe various pyrolysis properties of oil shales (see surveys 3, 9, 11 and articles 1, 2, 4-8, 10, 12),4 but they do not describe a generally applicable analytical procedure for detailed evaluation of thermal degradation products. The analytical method presented here for such evaluations is designed to provide for: 1. Control of retorting conditions--temperature, heating, rate, reaction atmosphere--plus some control over retort pressure and carrier-gas flow, 2. Precise direct gravimetric measurement of the thermal degradation products--oil, water, gas, and spent charge (residue after thermal treatment of the charge). 3. Samples of all products. 4. Determination of the identities and amounts of gaseous compounds produced. 5. Elemental analysis and gross heating value of all products. 6. Determination of the distribution in the retorting products of the elements present in the original samples.

Jan 1, 1962

By J. A. Stampe

In connection with its investigations of strategic minerals in the United States, the Bureau of Mines ran magnetic surveys totaling more than 533,000 linear feet at 30 deposits of magnetite in northern New Jersey. These deposits occur in a belt of granitic gneiss and in limited areas of limestone. The ore consists of magnetite accompanied by score of the following minerals: Hornblende, augite, apatite, feldspar, biotite, calcite, garnet and pyrolusite. Results of these investigations are being presented in two reports of which this is the second. The first paper, Certain. Magnetite Deposits in New Jersey, by A. L. Neumann and McHenry Mosier, was issued in April 1948 as Report of Investigations 4225.

Jan 1, 1949

By David M. Gullikson

Since publication of the paper on the composition of California oilfield waters by Jensen (6)3/ in 1934 the only other information on the subject was published recently by Chave (4). To supply needed information on the composition of California waters in areas of current drilling activity, the Federal Bureau of Mines collected formation water samples for analysis. Thirty-eight samples from oil-and gas-producing formations in 12 fields located in Ventura, Kern, Glenn, and Colusa counties were analysed by the Bureau's San Francisco Petroleum Research Laboratory. The samples were selected particularly from fields where the water composition was not well known or where interpretation of electrical logs has been difficult and the interpretation may be affected by unusual composition of the water. These samples were obtained from rocks ranging in geologic age from Cretaceous to Upper Pliocene. Fifteen constituents of these waters were determined including sodium, potassium, calcium, magnesium, strontium, barium, lithium, chloride, iodide, bromide, carbonate, bicarbonate, sulfate, borate, and residual acidity. These analyses are the first to be published on California oilfield waters in which determinations for potassium, strontium, bromide, iodide, boron) and naphthenates were made on a significant number of samples. The electrical resistivities of tae samples were determined at 75° F. and 175° F.

Jan 1, 1961

By Philip C. Tully

This Bureau of Mines report contains experimentally determined vapor-liquid equilibria data for a helium-nitrogen-methane mixture with a nominal composition of 15, 60, and 25 mole-percent, respectively. Measurements of the equilibrium phase compositions were obtained by means of a windowed cell, in conjunction with an automated chromatograph and a special analyzer for low helium concentrations. The data presented include a comprehensive table and eight graphs depicting phase compositions, vaporization ratios, and correlations with a previous study of two helium-nitrogen-methane mixtures of different compositions.

Jan 1, 1976

By Constantine C. Popoff

During 1946 several limestone deposits near Fortson, Snohomish County, Wash., were examined by the Bureau of Mines. These examinations were part of a long-range investigative program of regional mineral supplies required by the anticipated industrial development of the Pacific Northwest. The .study outlined in the following paper was specifically undertaken to disclose new sources of high-purity limestone and to appraise, their economic aspects. The deposits examined -namely the Galbraith, Climax, and Hi, Hi -are somewhat similar in physical features and geologic environment. They are lenticular and belong to the same formation of metamorphosed sediments that underlies the prominent Whitehorse Ridge.

Jan 1, 1949

By Edward D. Thimons

The Bureau of Mines conducted a state-of-the-art study of techniques currently employed to close large openings in underground mines. A large opening was considered to be any opening over 10 feet high and having a cross section of at least 200 square feet. Five salt mines and one limestone mine were visited to observe various methods of sealing large openings. Because of the variations in conditions from mine to mine, no definite conclusions could be drawn as to which is the best method. In mines where waste material is available, stoppings built by piling waste material are efficient and economical. Where waste material is not available properly constructed brattice cloth stoppings are superior to those built from wood, concrete block, or urethane foams.

Jan 1, 1975

By L. B. Berger, S. J. Pearce

One phase of Bureau of Mines' work in health and safety is promotion of the use of safe, satisfactory, and reliable respiratory protective. devices. To insure that such devices will be available, the Bureau has established schedules of minimum requirements for self-contained breathing apparatus, gas masks, supplied-air respirators. (hose masks, air-line respirators, and abrasive blasting helmets, hoods, or masks), dispersoid (dust, fume, and mist) respirators, and nonemergency gas respirators (chemical cartridge respirators). Approval tests of self-contained breathing apparatus are conducted by the Safety Branch; approval tests of other types of respiratory protective equipment are conducted by the Health Branch. Both branches are in the Health and Safety Division.

Jun 1, 1950