Search Documents

By Ernest L. Corp

Seepage forces computed by a finite-element flow program are combined with gravity forces in an elastic-plastic stress-analysis program to determine the stability of mine-waste slopes. Computer output provides a cross-sectional plot of the dam or embankment showing the safety factors for each element. The combined finite-element program called SEEP-SLOPE was used to analyze several trial embankments and the 1972 Buffalo Creek Dam failure Safety factors computed by the finite-element method (FEM) were compared with those computed by Bishop limiting-equilibrium method. For individual slip circles, there was little correlation between the factors of safety computed by the two methods. Both predict failure, but FEM shows a different mode of failure plus development of potential failure zones not indicated by conventional methods. Besides having a better theoretical basis than the Bishop method, FEM requires no assumptions regarding the location or geometry of the failure surface. As a result, the program will show progressive development of a failure zone, and areas can be pinpointed where remedial measures should be taken. In addition, nonhomogeneous cross sections can be analyzed, and zones of potential piping can be defined.

Jan 1, 1975

By Stanton L. Tainter

"As an adjunct to its minerals-investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the supervision of J. H. Hedges, chief, Tucson Branch Mining Division, and under the general supervision of Lowell B. Moon, chief, Mining Division, reports upon certain methods devised to overcome difficulties encountered in cementing of diamond-drill holes at a Bureau of Mines project at Christmas, Gila County, Ariz.Pressure grouting was employed to recondition a caved hole it was desired to reopen and deepen. The hole, which had boon stopped 7 months previously at a depth of 488 feet, was caved below 449 feet in a contact zone of claylike, altered diorite and crumbly metamorphosed limestone. As other means of obtaining moderate pressure were not available, carbon dioxide gas, drawn from tank of liquid carbon dioxide through a pressure reducing and regulating valve, was used. The hole was reopened successfully with 12 grouting jobs.Another hole, where cawing from several water-bearing fractures between 202 and 232 feet gave trouble, was successfully cemented by the use of a grouting plug. An attempt to cement through the rods had failed, owing probably to agitation caused by water currents. Pressure grouting through the caning set above the cave could not be need, because water was forced up outside the casing when pressure was applied. The problem was solved by using a wooden plug 1-13/16 inches in diameter, which, when soaked in water, expanded to a tight fit in an AX hole. A hole was drilled through the plug, and a rubber flap valve was nailed to the lower end. In the upper end of the plug the hole was enlarged to fit loosely over an EX rod coupling finished smooth. The plug was lowered on the end of the drill rods to a point about 10 feet above the cave, where it was allowed to expand tightly to the hole. Cement grout was then pumped through the rods, and the rods were removed from the hole. After allowing time for the cement to set, the wooden plug was chopped out and drilling van resumed.Over 300 tests were made to determine the type of cement most suitable for use on the Christmas job, and the effect of cement-water ratio, temperature, and various admixtures on workability, setting time, and strength. The results of these tests, described in detail in the body of this report, indicate the desirability of thoroughly testing available cements when it is necessary to drill holes under difficult conditions that may cause failure.When it became desirable to reopen and deepen a caved drill hole, it was considered easiest to recondition the hole by pressure grouting, As other mans for obtaining moderate pressure were not available, a method utilizing carbon dioxide gas was employed. The hole was reconditioned successfully with 12 grouting jobs."

Nov 1, 1949

By John Redington

This paper describing the milling practice at the Coniaurum Mine is one of a series of papers on milling methods, practice, and costs prepared in cooperation with an published by the United States Bureau of Mines. The 500-ton will of the Coniaurum Mines (Ltd.) is located at approximately the center of the company's property and a little more than a mile from the town of Schumacher, Ontario. The main shaft through which all the ore is heisted is adjacent to the mill so that the ore hoisted in a 3-ton skip is dumped directly into a 15-ton bin at the crusher.

Jan 1, 1931

By Jack C. White

The purpose of this Bureau of Mines research was to determine the technical feasibility of direct sulfuric acid digestion of Florida land-pebble phosphate matrix. Preliminary tests in a continuous digestion circuit showed that 92 to 96 percent of the P2O5 contained in the matrix was extracted, while the P.05 concentration in the product acid ranged from 21 to 30 percent. The waste filter cake contained about 1 percent P205 and up to 18 percent water. These sandy compact filter cakes, comprised mostly of quartz and gypsum, appeared to be suitable for backfilling and reclamation of mined lands.

Jan 1, 1975

By C. F. Davidson

The Bureau of Mines studied the extraction of lithium from lithium-containing clays by chlorination with hydrogen chloride (HC1). In bench-scale laboratory investigations, HC1-H20 mixtures were used to selectively chlorinate lithium, but not calcium or magnesium, in lithium-containing clays. The addition of calcium carbonate to the clay was found to improve the lithium recovery. Reaction conditions found to affect the lithium recovery were ratio of clay to carbonate, reaction temperature, and HC1 concentration. The best conditions for selective chlorination of the lithium were 2:1 clay-carbonate, 750° C, and 20 wt-pct HC1. The experimental results and trends in lithium extraction are explained using thermodynamic relationships.

Jan 1, 1981

By J. Kruttschnitt

This paper, describing milling practice at Mount Ira Minis, is one of a series covering milling methods and cost that is being published by the Bureau of Mines, United States Department of the Interior. The Mount Isa concentrator began operations in day 1931 by treating a mixture of oxidized and sulfide ores. Since March 1935 only sulfide ores have been milled; this change involved major alterations to the flow sheet. The maximum capacity on mixed oxide and sulfide ores was 2,650 tons per day; the present capacity is approximately 1,880 tons of sulfide ore per day. The installation of additional crushing, grinding, and flotation equipment when completed early in 1939 will increase the maximum capacity of the concentrator to 2,240 tons of sulfide ore daily.

Jan 1, 1939

By Stephen Krickovic

Air quantity-pressure and methane concentration surveys were conducted by the Bureau of Mines in accessible portions of an area being pillared in a Pittsburgh coalbed mine in West Virginia. These included two mined-out and three active butt headings and a bleeder system. The particular mine workings were started in virgin coal directly from a set of main headings; the main reason for the study was the difficulty usually encountered in adequately bleeding the gobs under such conditions. Although the two separate return airways in each active butt heading and the North and 1 Left bleeders contained acceptable methane concentrations (0.01 to 0.78 percent in the butts and 0.73 to 1.0 percent in the bleeders) with significant total methane removal (109 cfm in butts and 631 cfm in bleeders), there were relatively large areas in the gobs with possible minimal airflows. This condition appears to have developed from lack of systematic regulation of the airflow across the gobs and appears to indicate the existence of considerably more methane in the probably low flow areas in the gob.

Jan 1, 1973

By G. S. Rice, H. P. Greenwald, H. C. Howarth

"Stoppings in coal mines serve, important and. vital functions, such as coursing the ventilating current, sealing off abandoned or dangerous workings, sealing fire areas, and separating mines at boundaries. Stoppings may hold back water, but normally that is not their function; their design is, or should be very different from that of a hydraulic dap which is designed to a definite load, often a very heavy one, from one direction over an indefinitely long period. Hence, a dam usually requires an arched structure to resist hydraulic pressure, and it must be massive to meet vertical stresses due to heavy ground pressure.Stoppings are designed primarily to resist a pressure applied laterally through air or gases. Their strength cannot be stated without specifying the direction of applied load. A stopping may be placed in stress by proof pressure subsequent to erection, through extraction of pillars in the vicinity which may act direct, or by squeezing the ribs or heaving the floor. These forces act more or less parallel to the faces of the stopping and may be very great but measures must be taken suitable to each case, and it is impossible to allow for these in general specifications other than to call for normally good construction. A stopping is principally designed to resist the action of forces at right angles to its face, such as the shocks of blasting, the pressure of gas from instantaneous violent out bursts such as have occurred in certain British Columbia coal mines, sudden compression of the air by great falls of roof in closed spaces, and at time pressures that accompany an explosion of either fire damp or coal dust or both. This paper deals with the tests of pressures of explosions only."

Sep 1, 1930

By W. J. Huff, G. W. Jones, I. Spolan, R. E. Kennedy

"INTRODUCTION Information on the exploeibility and ease of ignition of acetylene is important in connection with investigations by the Bureau of Mines and others seeking the causes of explosions in medium-pressure acetylene generators.A previous report 6/ gave preliminary results of an investigation made by this Bureau to determine the causes of these explosions. This report indicated the need of amending Federal specifications for ""1/4 by 1/12"" carbide to reduce the amount of fine sizes permitted under the specifications then in force. Tests described in the above report showed that certain sizes of carbide may, under certain conditions, attain excessively high temperatures when acetylene-water vapor mixtures are passed through carbides for extended periods.Federal specifications P-0-101, Amendment 5, June 28, 1944, are now in effect. These latest specifications permit a maximum of 7 percent of ""1/4 by 1/12"" carbide by weight to pass through a 0.0661-inch sieve and a maximum of 2 percent to pass through a 0.0555-inch sieve. Experience has shown that these specifications have insured a safer size range of carbide for medium-pressure acetylene generators.Although the improvement in the size range of the carbides has aided in the prevention of explosions, there have been explosions in which the carbide used at the time of the explosion met the latest Federal specifications."

Sep 1, 1945

By C. M. K. Boldt

The Bureau of Mines surveyed waste disposal sites at 18 metal and non-metal mines and conducted laboratory and full-scale field tests to de-termine the effects of tailings deposition techniques on physical properties of tailings pond beaches. Survey data included measurements of beach slopes, descriptions of deposition techniques, and measurements of beach physical properties taken at various distances from the point of discharge. Laboratory tests involved depositing two types of tailings, each with different grain-size distributions, into a settling trough and determining the resultant physical properties of settled materials along the length of the beach. Side confinement and the closeness of the water pool to the point of deposition caused the laboratory results to be inconclusive. Full-scale field deposition tests conducted at the tailings pond of a cooperating mine showed that there were similarities in relationships between exit velocities of tailings slurry and physical properties of the settled tailings on the beach.

Jan 1, 1988

By A. Gene Collins

Some of the geochemical relationships that exist between subsurface fluids and the associated geologic strata in petroleum producing areas of Louisiana have been determined. Samples of petroleum-associated water were obtained from 126 wells in Louisiana that produced from sediments of three geologic ages: Tertiary, Cretaceous, and Jurassic. The samples were trans-ported to a central laboratory for analysis of chemical composition, using standard methods, to determine if the compositions varied with the geologic strata of their source and, if so, why. The dissolved constituents were com-pared with those of a brine that was concentrated by evaporation. The concentrations of bromide, calcium, and strontium were useful in distinguishing the brines produced from sediments of a late age from those of an earlier age. The concentration ratios of Mg' (total equivalent magnesium) and bromide indicated that dolomitization probably had occurred and altered the composition of the brines. A principal-components analysis of the data indicated an inverse relationship between depth and concentrations of bromide, strontium, calcium, and lithium.

Jan 1, 1970

In 2005, a total of 263 metal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Metal mines were the smallest mining commodity sector, comprising 1.8% of all mining operations. ? Gold mines comprised 46.0% (n=121) of all metal mining operations. Other common types of metal mines were iron ore (n=32; 12.2%), copper ore (n=31; 11.8%), and lead and/or zinc ore (n=16; 6.1%). ? Nevada had the largest number of metal mines (n=52; 19.8%), followed by Alaska (n=27; 10.3%).

Jan 1, 2008

By C. N. Rosenecker

The power required to circulate a gas-solids suspension was determined using a centrifugal compressor and a closed system. The suspension consisted of 18- to 40-micron glass beads in a mixture of 89 percent N2 and 11 percent CO2 at 20 psig. Solids-to-gas (S/G) ratios w re O to 2.2 lb/lb; gas flow rates were l.2 to 2.5 lb/min. Power requirement was found to follow the relationship hp t = hp(. + l), where hp t = the total power, and hpg = the power required for pure gas.

Jan 1, 1967

By W. G. Messner

Pipelines for transporting crude oil and refined products in the United States totaled 189,982 miles on January 1, 1959. This mileage was less than a 1-percent increase from the 1956 total of 188,540 miles. During the three-year period (January 1956 - January 199), 14,886 miles of new pipe and 10,649 miles of secondhand pipe was laid. Pipe taken up in the same period was 24,093 miles. The facts regarding pipeline mileage were obtained by the Bureau of Mines from pipeline companies and information provided by the Interstate Commerce Commission. Crude-oil gathering lines, as of January 1959, were 40 percent of the United States pipeline mileage and totaled 75,182 miles, an increase of 1,656 miles during the three-year period. Crude-oil trunklines totaled 70,317 miles or 37 percent of the United States pipeline mileage, a decline of 8,277 miles from the 1956 total. Some of this loss is attributed to the converting of crude lines to refined products. Refined product lines in January 1959, totaled 44,483 or 23 percent of the United States mileage, an increase of 8,063 miles during the three-year period.

Jan 1, 1959

By R. V. Higgins

The, large volumes of low A. P. I. gravity oil that will remain in many shallow fields of California when such oils no longer can be recovered profitably by pumping are important potential sources of oil when ways and means are found to remove them from the reservoir sands. Estimated ultimate oil recoveries in many of the "low-gravity fields" of the San Joaquin Valley in California indicate that less than 25 percent (on the average) of the original oil will be recovered. These oils have viscosities of 1,000 or more centipoises at reservoir temperatures and, because of their high viscosity and low intensity of the reservoir pressure, the quantities that will be retained in the sands ultimately are so large and their recovery is such a challenge to petroleum engineers that the Bureau of Mines has made the study of their possible recovery one of its major projects. The fact that a slight increase of temperature materially reduces the viscosity of low A. P. I. gravity oils has 'prompted the use of various means for increasing the temperature of the oil in the reservoir sands and hence the rate of flow and Completeness of recovery of the oil. Hot oil, hot water, heated air, and natural gas, steam, super-heated steam, and the products of combustion have been circulated in wells to raise the temperature of the oil it the sands; electric heaters have been installed in wells, and butane and air have been intermittently exploded and the flames propagated through the tubing to the "pay" zones. None of the methods, however, have been entirely satisfactory for the recovery of large quantities of oil.

Jan 1, 1949

By Dennis R. Dolinar

The danger to personnel, equipment, and pillar structure created by the spalling of a coal rib can be minimized by installing rib bolts. To assure that a configured support system will maintain a coal rib, the U.S. Bureau of Mines developed a rib bolt system based on a nonpreventable failure concept. A statistical equation quantitatively relates the amount of rib retained to the bolt spacing and the width of the spalled material. Laboratory test results show that the equation accurately predicts the amount of material retained and confirm the validity of the support concept. The examination of rib bolting at a coal mine experiencing rib sloughage provides evidence that the effectiveness of the support can be related to the failure pattern of the spalled material. An analysis of roof and roof support reaction to rib sloughage at the mine indicated that the rib sloughage had little effect on roof stability. Although supporting ribs might not affect roof stability, laboratory test results indicate that the material retained by the support can sustain a load up to 20 pct of the intact compressive strength of the material.

Jan 1, 2010

By John M. Gomes

Two molten salt systems were evaluated as electrolytes for the repetitive recovery of tungsten from tungsten oxide (W03) made by calcining commercial-grade ammonium paratungstate. Using a sodium chloride-sodium fluoride-potassium aluminum tetrafluoride electrolyte at 800° C, 1 pound of 99.8 percent tungsten was recovered for each 2.7 kilowatt-hours of energy consumed. The metal contained 1,100 ppm carbon, was in dendritic masses of spherical grains, and had an apparent bulk density of 5.41 g/cm3. T ngsten of 99.9 percent purity was won from a sodium pyrophosphate-sodium tetraborate-sodium chloride electrolyte at 1,000° C; 6.0 kilowatt-hours of energy was consumed for each pound of metal recovered. The metal contained 120 ppm carbon, was in dendritic masses of hexagonal acicular crystals, and had an apparent bulk density of 7.25 g/cm . Each metallic impurity--aluminum, calcium, copper, iron, nickel, and silicon--in the two tungsten products was 16 ppm or less.

Jan 1, 1966

By Robert L. Virta

The Bureau of Mines examined a fibrous talc sample from the Gouverneur talc district in New York by transmission electron microscopy (TEM) and polarized light microscopy to determine the mineralogical relationship of the fibrous talc to the amphiboles present in the sample. Two am-phiboles, anthophyllite and tremolite, were present in the sample. Tremolite occurred as a separate mineral phase, which was blocky in habit. Only a few composite tremolite-talc grains were observed. An-thophyllite, however, was present only in the fibrous talc grains. Mi-crodiffraction study of the fibrous talc grains containing anthophyllite showed that the anthophyllite was intermixed with the talc on a fine scale and that there was a crystallographic relationship between the talc and anthophyllite lattices in the fibrous talc grains. A mechanism similar to the process that forms biopyriboles could explain the structural defects, the fibrous habit of the talc, and the structural relationship between the talc and anthophyllite in the fibrous talc grains. Because of these characteristics, phase contrast microscopy and a provisional TEM technique for monitoring asbestos exposure would not distinguish between fibrous talc and fibrous amphiboles. TEM techniques employing electron diffraction and energy-dispersive X-ray analysis are recommended to positively identify the fibrous phases for regulatory purposes.

Jan 1, 1985

By A. B. Coates, J. E. Crawshaw

"The use of such methods and apparatus as the Dautriche method and the Mettegang recorder for the determination of the rate of burning of black blasting powder and other strictly burning explosives has been found to give such erratic results that no reliance can be placed on the data thus obtained. Consequently, investigators of those factors which may affect the burning rate, such as size of grain, absolute density, chemical composition, and means of ignition have had to rely mainly on observations made during practical use for determination of the part played by each. Such tests are very difficult of interpretation.The purpose of this paper is to describe a method used by the explosives division of the Bureau of Mines for the investigation of such explosives and to present the results of an investigation using that method.The investigation was concerned with the effect of grain size, initial pressure, and means of ignition on the rate of burning or rate of pressure development of black blasting powder as compared with pellet powder.The Bichel pressure gauge was used for these tests, with the slight modification to the apparatus and method described in U. S. Bureau of Mines Bulletin 15.4 These modifications consisted of reducing the speed of the revolving drum on which the time-pressure record is taken, measuring the speed of the drum by a belt-driven tachometer, and introducing an induction coil in series with the electric squib or electric detonator to mark on the time pressure record the instant at which the squib or detonator was fired."

May 1, 1929

By R. Hogg, T. H. Dumm

"The mathematical treatments used in the evaluation of particle size distribution from pipet-withdrawal centrifuge data are reviewed. An error in the published procedure for multiple-sample withdrawal systems is pointed out and a corrected formulation is presented. An alternative treatment, based on a piece-wise linearization of the size distribution is described. Computer simulations of the analytical and data evaluation procedures indicate that the errors in the original formulation are not generally serious and that the corrected and alternative procedures lead to very similar estimates. Except for some cases involving very narrow size distributions, the alternative approach appears to give slightly closer estimates of the size distribution. Comparisons based on actual experimental data are also described.1 IntroductionSedimentation methods are widely used for the determination of particle size distributions. The procedures are relatively simple to use and the results are essentially absolute, requiring no external calibration. Gravity sedimentation is typically applicable to particles in the size range of about I to 50 pm and generally involves measurement of the relative concentration of particles as a function of depth and time in a dilute suspension. Particle size is calculated using Stokes, law:"

Mar 1, 1989