Search Documents

By R. D. Leitch

[The accepted theory of acid formation in coal mines with the subsequent appearance of the acid in coal-mine drainage, is oxidation of iron pyrite and subsequent solution and hydrolysis of the iron sulphate formed. It has also been found that 5 gobbed sections and worked-out areas, where there is usually an abundance of iron pyrite-bearing, materials in contact with air, are the sections that make the most important contribution to the quantity of acid drainage. It would thus seem obvious that if oxygen can be kept out of contact with tae acid-forming materials in tie- sections mentioned the amount of acid in coal-mine drainage could be reduced markedly and corrosion problems with mine pumping equipment and general stream pollution mitigated thereby. Although the efficiency of the suggested remedy as been borne out by laboratory experiments6, it has appeared desirable to substantiate the laboratory work by field observations in so far as pertinent data are available. It has been difficult to learn of mines or sections of mines about to be sealed, whereby an actual comparison of the drainage before and after sealing can be made. In view of that difficulty it has been necessary to devote attention to a comparison of the character of the water from areas already sealed with that from open but otherwise comparable sections of the sane mine. Previous cork has shown that the acidity of drainage in different parts of the same mine may vary, but if it can be shown also that the water from sealed areas is with but fen exceptions less acid than the otherwise similar open sections of tae same mine, the laboratory finding will be supported in a practical gray. This report presents some of the evidence that has been obtained.]

Jan 1, 1930

Ten years ago we surveyed in "Uspekhi Khimii" the mechanism of the synthesis of hydrocarbons from CO and H2 (1).5 With new data obtained since then, mostly by Soviet researchers, our previous work (2), dealing with new forms and catalysts of the synthesis, is brought up to elate by reviewing research in this field. FORMATION OF CARBIDES The hypothesis that carbides are intermecliates in the synthesis assumes that carbon monoxide reacts with the metals of the eighth group and that this reaction is connected with the reversible reaction 2CO[=]C +CO2 (1) in a certain range of temperatures (3).

Jan 1, 1958

By James V. Kelly

During the winter of 1946 and the spring of 1947, the Bureau of Mines conducted an investigation and drilling program in the vicinity of the village of Fairplay, Wis. Fifteen diamond drill holes totaling 2,457.6 feet of bore were completed. This work was part of a general study of the zinc-producing area of southwestern Wisconsin and had the particular purpose of investigating a structural trend, determined by the Federal Geological Survey, in an area some distance from known ore bodies or active mines.

Jan 1, 1948

By R. Hogg, T. F. Dumm

"There is a considerable need for standardized respirable dusts with consistent, reproducible characteristics which simulate those of actual mine dust. The availability of such materials should be a significant factor in promoting coordinated research into dust characterization and mine monitoring, dust control, and the biomedical aspects of dust toxicology. The use of an opposed-jet, fluid-energy grinding system in closed circuit with a cross-flow, centrifugal air classifier for preparing bulk quantities of respirable-size dust has been investigated, and appropriate, standardized procedures have been established. By stage-crushing, screening, and fine-grinding with a Donaldson Acucut classifier/mini-grinder system, it is possible to produce bulk quantities of respirable dust at relatively high rates. Using minor modifications to the system, broader or narrower size distributions can be prepared within the respirable range. The system has been shown to reach steady-state with respect to product size distribution very rapidly. However, preferential grinding/classification effects appear to lead to a slow build-up of mineral matter in the circulating load with a corresponding slow change in product composition with time. In those applications where the dust composition is required to match that of the feed coal, it may be necessary to allow considerable time for a true steady-state to be established.Standard respirable dust samples have been prepared from coals representing the western (high volitile A bituminous), central (medium volatile bituminous) and eastern (anthracite) mining areas of Pennsylvania. Quartz and kaolin clay samples, representing important mineral constituents of coal dust have also been prepared. Extensive characterization studies have been performed on the samples to evaluate chemical and mineralogical composition and the distributions of particle size and specific gravity. Detailed information on the original coals is available from the Penn State Coal Data Base. The standard coal dust samples appear to simulate actual mine dust very well with respect to particle size and shape, but generally have somewhat lower ash content. Samples of these standard dusts have been made available to research groups concerned with respirable dust in mines."

Mar 1, 1989

By H. C. Ko

Calorimetric determinations of low-temperature heat capacities and the standard enthalpy of formation were made by the Bureau of Mines for aluminum sulfide, A12S3. The standard entropy (S°), enthalpy of formation (?Hf°), and calculated Gibbs energy of formation (?Gf°) at 298.15 K are 27.93±0.05 call deg-mole, -155.6±0.9 kcal/mole, and -153.0±1.0 kcal/mole, respectively.

Jan 1, 1976

By K. E. Stanfield

Asphalts from. Wyoming "black oils" are being studied at the Petroleum Experiment Station of the Bureau of Mines at Laramie, Wyo., in cooperation with the University of Wyoming. These black oils are characterized by their high-asphalt, high-sulphur, and low-gasoline content and are difficult to refine by present methods into high-octane motor fuels, burning oils, and lubricants. Accordingly, their principal use, at present, is for the manufacture of road oil and asphalt. The present production of black oil could be increased to meet a greater demand. During 1937 the daily production of these crude oils in Wyoming was slightly over 13,000 barrels, while, the estimated potential production from existing wells was 56,000 barrels.

Jan 1, 1939

By A. F. Baker

The Bureau of Mines conducted pressure-drop studies in a 4-foot-diameter simulated blast furnace shaft to compare anthracite metallurgical briquets with coke and formcoke. The test materials were used alone, layered, and in mixed burdens of commercial fuel-to-ore ratios. Anthracite briquets had a higher pressure drop per foot than furnace coke, but they had a lower pressure drop per foot than formcoke. This appears to be due to packing and shape, as well as to particle size. The superficial air velocities at which beds of briquets and furnace coke disrupted were about the same. However, if briquets of the shapes and sizes tested are substituted for furnace coke in commercial metallurgical furnaces, higher blowing pressures will be required to deliver comparable amounts of air. Test burdens with more than 5 percent material smaller than 1/4-inch diameter showed significant increases in resistance to airflow.

Jan 1, 1967

By P. D. Lindahl

[A cost/benefit analysis was conducted by comparing the industry cost to protective structures on low-coal face equipment with the benefits paid for injuries/fatalities considered preventable by the use of these structures. Th industry costs were based on estimates by OEM's and rebuild shops for install protective structures on new and rebuilt face equipment. The accident benefit was based on evaluations performed by the USBM Accident Cost Indicator Model. Industry wide population data were developed on low-coal face equipment and injuries/ fatalities preventable with protective structures. The results of the analysis are to be used as a tool by USBM in determining the feasibility of continuing development of cab and canopy technology for low-coal equipment.]

Jan 1, 1983

By Jack L. Woodward

The evolution of surface mining equipment has resulted in larger, faster haulage units, loaders, etc., resulting in increased demands on steering technology. Careful analysis of these systems was warranted to determine if steering-related safety problems have been introduced. The objectives of this program were to: 1. Define the generic types of steering systems being used on mobile mining equipment used in surface mining operations. 2. Gather information on steering-related accidents in mining operations. 3. Assess the need for initiating government-sponsored research into steering system technology. A comprehensive literature survey was conducted concurrent with extensive contacts with mining operations, mining equipment manufacturers, steering system component manufacturers, and government agencies. A Technical Evaluation Group composed of representatives from the above organizations was formed to review the data gathered. It was concluded that the steering systems in use on surface mining equipment are reliable and do not present a safety problem. The Society of Automotive Engineers, Inc. is active in pre-paring voluntary consensus standards to assure that the minimum levels of performance are defined for industry.

Jan 1, 1979

By H. A. Doerner

The Rare and Precious Metals Station of the U. S. Bureau of Mines has investigated several cases in which widely divergent amounts of molybdenum were reported by a number of custom laboratories to which quartered portions of the same sample had been sent for analysis . On an oxidized lead ore containing considerable vanadium and a little molybdenum , the amount of the latter reported ranged from 3.14 to 0.24 per cent M003 . The high results were due to the fact that vanadium was estimated with , and reported as , molybdenum . When analyzed by the method described in this paper , 0.15 per cent Moog was found, which is a fair agreement with the lowest figure previously reported . In another and more unusual example , a fine- grained rock containing considerable graphite was submitted for analysis . As a white residue could not be obtained by treating this material with acid , several chemists decomposed the ore by a prolonged fusion with soda ash and nitre and leached the melt with hot water in crder to insure the dissolution of any and all the molybdenum present . After precipitating and filtering the silica from the solution , acetic acid , ammonium acetate , and lead acetate were added to precipitate lead molybdate . The solution contained phosphorous derived from the ore , which precipitated as lead phosphate . The latter was mistaken for , and reported as , molybdenum. As two different chemists used essentially the same procedure , their results , although incorrect , checked . Other chemists using different methods found no molybdenum . From these and other instances it is evident that reputable and conscientious assayers may make serious errors in determining molybdenum, and even duplication of results by different chemists does not necessarily insure against error . The elements most likely to cause trouble are vanadium, tungsten, uranium , arsenic , antimony , titanium, tin , phosphorous , and chromium . The precautions necessary to eliminate these and other impurities vary with the type of ore and the method of analysis . Most texts present methods of limited application and omit or fail to emphasize adequately such precautions . No one method can be given that will best fit every case , but the following procedure has been selected as being the simplest reliable method for such occasional determinations of molybdenum in an ore as are encountered in customs work.

Sep 1, 1930

By M. E. Tyrrell, C. W. Houck

Mixtures of zirconium diboride and refractory metals of group VI were resistance sintered to high - density compacts using modified electric welding equipment . To evaluate the use of chromium , molybdenum , or tungsten as binders for zirconium diboride the sintered compacts were examined in polished sections and tested for crushing strength , hardness , microhardness , oxidation rate , and resistance to mechanical shock . Chromium yielded the highest compressive strength , the greatest resistance to mechanical shock and oxidation , and a satisfactory Rockwell hardness . Molybdenum did not yield a satisfactory cermet . Tungsten yielded compacts having high microhardness but very low mechanical strength .

Jan 1, 1964

By John A. Organiscak

Enclosed cabs are a primary means of reducing equipment operators? silica dust exposure at surface mines. The National Institute for Occupational Safety and Health experimentally investigated various factor effects on cab air filtration system performance. The factors investi­gated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use, and wind effects on cab particulate penetration. Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that intake filter efficiency and recirculation filter use were the two most influential factors on cab penetration performance. Use of the recirculation filter reduced cab penetration by usually an order of magnitude over the intake air filter alone because of the multi­plicative filtration of the cab interior air. Intake air leakage and filter loading affected the cab penetration to a lesser extent, while wind had the least impact on cab penetration between the calm and 10-mph wind velocities tested. Adding an intake pressurizer fan notably increased intake airflow and cab pressure with only minor changes to cab penetration. A mathematical model was developed that describes cab penetration in terms of intake filter efficiency, intake air quantity, intake air leakage, recirculation filter efficiency, recirculation filter quantity, and wind penetration.

Jan 1, 2008

By John A. Organiscak

Enclosed cabs are a primary means of reducing equipment operators? silica dust exposure at surface mines. The National Institute for Occupational Safety and Health experimentally investigated various factor effects on cab air filtration system performance. The factors investi­gated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use, and wind effects on cab particulate penetration. Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that intake filter efficiency and recirculation filter use were the two most influential factors on cab penetration performance. Use of the recirculation filter reduced cab penetration by usually an order of magnitude over the intake air filter alone because of the multi­plicative filtration of the cab interior air. Intake air leakage and filter loading affected the cab penetration to a lesser extent, while wind had the least impact on cab penetration between the calm and 10-mph wind velocities tested. Adding an intake pressurizer fan notably increased intake airflow and cab pressure with only minor changes to cab penetration. A mathematical model was developed that describes cab penetration in terms of intake filter efficiency, intake air quantity, intake air leakage, recirculation filter efficiency, recirculation filter quantity, and wind penetration.

Nov 1, 2008

Commodities statistics and otter information are available through the following t et systems: Internet Access: To acccess the USBM Gopher server on Internet, connect to: gopher.usbm.gov port 70, using gopher client software. Or contact the Systems Administrator for technical questions: Matt Klevemann, 412-892-6499 (klevemmc@miner.usbm.gov) These USBM materials are available on Internet, with more to come in the future: Publications and other research findings, including this bimonthly publications list, newsletters, tech transfer updates, enviromental technology research, health and safety information. USBM software products Media materials and speeches. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. Mines FaxBack: Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644. 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone. 4. After completing your selection, press the start button on your fax machine.

Jan 1, 1995

By H. W. Kilau

The Bureau of Mines evaluated synthetic fluorspar as a substitute for natural fluorspar flux in basic cupola ironmaking. The synthetic fluor-spars tested were prepared from waste fluosilicic acid generated during the processing of fluorapatite ore. The cupola trials showed the synthetic products to be the equivalent of natural fluorspar from an operational standpoint. However, wet scrubber sampling showed that substantial losses of volatilized fluorine occurred from the cupola during operation. The losses during synthetic fluorspar trials considerably exceeded those from natural fluorspar trials. Laboratory viscosity testing, using a high-temperature rotational viscometer, confirmed this finding and indicated that fluorspar volatility in slags is related to slag basicity. Synthetic fluorspar is accordingly recommended more for highly basic cupola operation (>1.3 basicity) than for neutral or acid operation, because of the increased potential for pollution and baghouse filter detezioration"

Jan 1, 1989

By Richard A. Thomas, Michael J. Sapko, Gary L. Mowrey, William D. Monaghan, Michael A. Trevits

Over the years, more than 20,000 mine seals have been erected in underground coal mines in the United States. Seals are used extensively in underground mines to isolate worked-out areas, active mine fire zones, and to control water inundations. Seals are most often built directly in the mine and can be fabricated from blocks made of wood or cementitious material. Recently, several explosions occurred within sealed areas of underground U.S. coal mines. These explosions, believed to be initiated by lightning strikes on the surface, destroyed numerous seals and caused considerable damage external to the sealed area. The National Institute for Occupational Safety and Health is conducting research to develop design guidelines, to investigate noninvasive techniques to characterize seal strength properties, and to evaluate seal test methods. As part of this work, a 30-ft wide, 16.1-ft tall and 4-ft thick seal was built in an underground experimental mine using cement and foamed water. Two types of noninvasive techniques are currently being investigated, namely the Schmidt Hammer for measuring compressive strength and ground penetrating radar (GPR) for detecting the presence of anomalies (e.g., voids, discontinuities) within the seal. Once these noninvasive tests were completed, the seal was subjected to destructive explosion testing. This study presents the results of the Schmidt Hammer tests, GPR scans, and the characteristics of seal failure during explosion testing.

This report is the 23d in a series summarizing research and technologic work by the Federal Bureau of Mines on coal and related investigations; it is the fifth report to be issued on a calendar-year basis.2/ Publications by Bureau personnel in 1958 are cited;3/ in addition work in progress during the year is briefly described. To conserve our reserves of coal the Bureau of Mines conducts a program concerned with the development of fundamental information on coal characteristics and behavior, and the improvement of technology related to its production and utilization. The ability to anticipate and meet future demands for coal depends on a number of factors: (1) Knowledge of reserves from a stand- point of both quantity and quality; (2) the development of improved mining methods, health and safety measures, and preparation techniques that will insure its most efficient exploitation; and (3) knowledge of the controlling factors in efficient use of coal in combustion, carbonization, gasification, direct and indirect hydrogenation, and other new processes. The Bureau is concerned with each of these areas.4/,5/

Jan 1, 1960

By Bruce I. Thomas

As a part of the United States Department of the Interior program for developing natural resources in Alaska, the Bureau of Mines studied the tin-bearing gold-placer deposits in the Tofty area of the Hot Springs district in central Alaska. The principal objective of the Bureau's work was to obtain facts about the extent and character of the placer deposits (including tailing) to indicate the economic or strategic tin-production potential of the Tofty "tin belt." A secondary objective was to determine (if possible) the bedrock Source of the cassiterite and other minerals found in the placer deposits. The placer phase of the work was begun in July 1954 and was continued during the 1955 and 1956 field seasons. Extensions to, and connections between, known placer channels were sought by 82 churn-drill holes. The Bureau drilling did not expand the placer deposits beyond the limits established by drift-mining operations and by previous drilling done by private concerns.

Jan 1, 1957

By John M. Devine

The severe corrosion of equipment that is caused by the presence of hydrogen sulphide in oil and gas has been described in detail by several authors. Such corrosion, termed "low-temperature hydrogen sulphide corrosion", presents a somewhat different problem from the "high-temperature hydrogen sulphide corrosion" that is encountered in refinery operation and which has been described by various-investigators of refinery corrosion.

Jan 1, 1932

By C. E. Armantrout, H. Kato, M. I. Copeland, M. Krug

The investigation of the nickel - gadolinium phase diagram was undertaken to determine the alloying behavior of these two metals . The data from meltingpoint determinations , thermal analyses , metallographic examinations , and X- ray diffraction analyses revealed a phase diagram with three eutectic points and seven intermetallic compounds . Very limited solubility of the phases in each other was observed . The five phases , Ni Gd , Ni , Gd , Ni Gd , Ni, Gd , and NiGd¸ , melted incongruently at about 1,300 ° , 1,270 ° , 1,180 ° , 1,070 ° , and 775 ° C , respectively . Ni Gd and NiGd melted congruently at approximately 1,550 ° and 980 ° C , respectively . Four of the compounds were determined to crystallize in the hexagonal system : Ni Gd , Ni Gd , Ni , Gd , and Ni Gd . Ni Gd was determined to be cubic and NiGd , orthorhombic . The crystal system of NiGd was not determined . The eutectic points occurred at 13 , 67 , and 85 wt pct gadolinium , and the isotherms at 1,290 ° , 890 ° , and 700 ° C , respectively .

Jan 1, 1964