Search Documents

By George H. Holmes

Beryllium deposits in the northern Virgin Mountains , Clark County , Nev . , and Mohave County , Ariz . , about 70 miles northeast of Las Vegas , were investigated by the Bureau of Mines . The investigation indicated a widespread occurrence of beryllium- bearing pegmatites within an extensive belt of mica - schist . Several deposits with significant beryllium mineral concentrations were encountered . Only a few of the samples analyzed contained more than 1 percent beryllium oxide ( BeO ) ; in many of the samples , no beryllium was reported . The average tenor of samples from the more important occurrences was 0.25 percent BeO . Chrysoberyl is the predominant beryllium mineral in the pegmatite sills ; beryl predominates in the more massive bodies . Minute quantities of cesium and lithium minerals also occur , but no columbium , tantalum , or other rare minerals were found . Ore dressing tests on a composite sample containing 0.28 percent BeO which was representative of the pegmatite sills , indicated an 85 percent recovery of the chrysoberyl ( 70 percent recovery of total BeO ) by gravity concentration in a concentrate containing 17.6 percent BeO .

Jan 1, 1964

By Richard W. Watson

Card-gap and projectile impact sensitivity data are presented for a wide variety of explosive compositions tested at the Bureau of Mines in more or less standard test geometries. The results of both tests are in good agreement in that they provide the same sensitivity ordering for different subclasses of explosives. Least sensitive were homogeneous liquids that did not exhibit a tendency to undergo low-velocity detonation, ammonium nitrate-fuel oil, and most cast military explosives. Of intermediate sensitivity were pressed and powdered military explosives, cast pentolite, permissible and non- permissible water-based explosives, and one commercial two-component explosive. The most sensitive were permissible and nonpermissible dynamites and explosives susceptible to low-velocity detonation.

Jan 1, 1973

By Joseph F. Davies

Along with the humanitarian need for preventing accidents the cost of injuries must be considered. As a means of bringing the facts concerning the prevalence of accidents in mining and their direct cost before the operating officials and others interested in accident prevention in the mining industry, the United. States Bureau of Mines ha as recently made studies and published reports dealing with these subjects in several States 4. This report gives available data on the causes and direct costs of accidents in Virginia coal mines for the 4-year period 1929 to 1932, inclusive. Mounting compensation costs and insurance rates resulting from mine injuries indicate the necessity of measures to decrease the number and severity of accidents. These direct costs, as well as additional losses of an indirect nature, can be eliminated from the cost of production to the extent that accidents are prevented or reduced in severity.

Jan 1, 1934

By M. J. Ankeny, J. J. Forbes

"One of the main functions of the U. S. Bureau of Mines, as authorized by Congress, is to investigate safety and health conditions, to disseminate information regarding safe and unsafe practices in mining, and to aid in improving safety and health conditions of mining communities and in promoting the welfare of the miner. Among several methods of reaching the miner and interesting him in safety work, perhaps the most effective is through the 11 mine safety stations and 11 railroad cars known as mine rescue, or more correctly, mine safety cars.Frequently, the Bureau of Mines receives requests for information regarding the purpose, equipment, personnel, and construction of its safety cars used in the field service. It is the intention of this circular to present to the mining public in particular, and to the public in general, some definite information regarding these safety cars and their functions.The cars are operated throughout the mining fields of the United States and are headquartered as follows (see fig. 1): Car 1, Reno, Nev.; Car 2, Raton, N. M.; Car 3, Pittsburgh, Pa.; Car 4, Terre Haute, Ind.; Car 5, Pineville, Ky.; Car 6, Pittsburg, Kans.; Car 7, Huntington, W. Va.; Car 8, Duluth, Minn.; Car 9, Butte, Mont.; Car 10, Des Moines, Iowa; Car 11, Anchorage, Alaska.One of the most important purposes of the U. S. Bureau of Mines safety cars is to render service at mine fires and explosions where human life is endangered. State mine inspectors and other interested persons are supplied with itineraries of the car operating in their districts from time to time, so that they may know at all times where the car can be found in case of emergency. When these disasters occur the car may be reached direct or through its field headquarters, and upon receiving word of a mine disaster, or request for assistance, it immediately proceeds to the scene of trouble. Frequently a special locomotive is supplied by the railroads and in many instances the movement of the car is given the right of way over all other railway traffic. Upon reaching the destination, the facilities and personnel of the car are immediately available for rescue and recovery operations.Following most mine disasters a thorough investigation is made by engineers of the Bureau of Mines, and a confidential report is submitted to the operator. The information gained in this manner from a large number of mine fires and explosions, together with the knowledge gained from the experimental work carried on at the Experimental mine of the bureau at Bruceton, Pa., serves as a basis upon which the bureau is able to recommend preventive measures whereby similar occurrences may be averted. The bureau car is often used as headquarters for the investigating engineer when such an examination is being made."

Mar 1, 1931

By C. B. Manula

In this report, the application of the Open Pit Materials Handling Simulator (OPMHS) to a Southwestern surface mine using draglines and front-end loaders is described. The specific objective of the study is to demonstrate the application of the simulator to analyze mine planning and to analyze alternatives for increased production. The simulator was verified by comparing long term production figures to the simulated results from data collected on a mine visit. A short term and a long term alternative are studied with projected productivities and scheduling. No economic analysis of these proposals were performed.

Jan 1, 1977

By W. J. Wenger

THIRTY-FOUR analyses of crude oils from the fields of the Four Corners Area of Arizona, Colorado, New Mexico, and Utah are presented and compared. The samples, taken from formations in four geological time periods, have high gravity and low-sulfur, -nitrogen, and -asphalt content. Generally, the oils are paraffinic in the low-boiling fractions, with increasing naphthenicity in the higher-boiling fractions. Oils from Cretaceous formations resemble other Cretaceous oils in the Rocky Mountains, but oils from Permian and Pennsylvania formations are unlike other oils of these ages in the Rooky Mountains. The differences in the oils are minor and cannot be used to distinguish between fields or between producing formations. With minimum special processing, the oils should yield large amounts of good-quality motor fuels. INTRODUCTION The only place in the United States where four States have a common junction is known as the Four Corners Area. This area (fig. 1) includes the northeast corner of Arizona, the southwest corner of Colorado, the northwest corner of New Mexico, and the southeast corner of Utah. It includes three major geological basins: The Black Mesa, the San Juan, and the Paradox. Major oil developments have occurred in both the San Juan and Paradox basins, but no discovery of commercial importance has been made in the Black Mesa basin.

Jan 1, 1960

By John C. Machisak

Injury data and experience, with related employment statistics, at coal mines in the United States for 1959 are presented in this publication under the following general sections: (A) General injury experience: Tables 1 to 6: Current data on number of injuries degree of injury, frequency and severity rates, average severity, and related employment and production data by work location. (B) Selected injury experience: Tables 7 to 38: Current data on principal agencies of injuries, distribution of injuries by part of body injured, days of disability, extent of hand and machine loading, experience by employment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation's coal mines.

Jan 1, 1961

By John W. Sweeney

Shales and clays from Illinois were sampled, tested, and evaluated to determine feasibility of producing lightweight aggregate by rotary-kiln methods. Sampling procedures and the 1 ,,,y of the Pennsylvanian shale units are discussed. Chemical, X-ray spectrographic and X-ray petrographic analyses were run on the samples to determine if a correlation existed between chemical mineralogic composition and expansion. Preliminary expansion testing was conducted in a muffle furnace. Rotary-kiln tests were conducted in a 16- inch by 14-foot rotary kiln. The weight of the aggregate ranged from 27 to 59 pounds per cubic foot. Concrete cubes employing the aggregate were tested to determine the qualities of the concrete. Compressive strength of the concrete using the 7-bag of cement cement per cubic yard mix, after autoclave curing for 6 hours, ranged from 2,950 to 6,750 psi. No correlation was found between the chemical, X-ray spectrographic, and X-ray and petrographic analyses and expansion, Sixteen samples made suitable lightweight aggregates in the laboratory rotary kiln. The expansion temperature range of eight of the samples was extremely narrow, and difficulties would probably be encountered in processing these materials commercially.

Jan 1, 1965

By Thomas J. Peters

The Lime Creek study area lies 100 air km east of Boise, and 70 air km northeast of Mountain Home, Idaho. The eastern boundary of the 28,000-hectare, east-west-elongate study area lies 0.2 km west of the 3,077-m-high Smoky Dome. The area is mainly underlain by Cretaceous granitoid rocks of the Idaho batholith. No mineral resources were identified, but two mines and one prospect were found in the study area. At the President and the Last Chance mines, in the southwest corner of the study area, gold mineralization occurs along steeply dipping east-northeast-trending faults and associated quartz veins, and within adjacent Cretaceous granitic rock. The mineralized material is not rich enough to mine underground, and near surface, open-pit-mineable deposit areas could not be identified. The third prospect, the Ventura, is within altered pink granite of probable Tertiary age, but metal concentrations are very low. Geothermal activity was not observed within the study area, but hot springs do occur in the Vicinity. Bedrock observed is only suitable for the most basic high bulk and low end value applications, such as crushed aggregate. Numerous sources for crushed stone occur closer to markets. Alluvial concentrate (placer) samples did not contain free gold, and no substantial alluvial bars were seen; deposits were too small to contain resources.

Jan 1, 1993

By William L. Crentz

Late in the nineteenth century en active coal-mining industry was begun in the Lower Freeport bed near Reynoldsville, Pa., where the bed thickened to more than 10 feet in places . The coal was readily accepted as an excellent steam fuel. Much of the thick coal his been depleted, but there are many areas where the deposit averages about 14 feet in thickness. As the more desirable mining sites were worked out in the Lower Freeport bed, other beds were exposed from which will come the county's major cowl production in future. The Lower Freeport bed is still the most important bed in Jefferson County from a production standpoint. The Lower Kittanning bed is second. Sporadic mining is being done in the Upper Freeport, Upper Kittanning, Middle Kittanning, Clarion, and Brookville beds. Strip mining has permitted recovery of much coal that could not be mined profitably by conventional underground methods.

Jan 1, 1953

By R. E. Lindstrom

A study of ion-exchange resin crosslinkage and eluant flow rate, resin-bed shape, and addition of separating ions to feed stock was undertaken to determine their effect on the separation efficiency of ion-exchange on bastna-site-rare-earth elements. Results show that 12-percent divinylbenzene (DVB) crosslinkage resin is detrimental to separation efficiency at flow rates over 2 to 5 ml./min./sq. cm.; whereas, separation with 4-percent DVB crosslinkage resin is relatively unaffected by flow rates between 2 and 10 m1./min./sq.cm.

Jan 1, 1959

By Anil Mahyera

Towards the goal of achieving uniform-high-tensions in roofbolts to provide superior roof support[1-7] for extended periods, Terra Tek installed mechanical-anchor bolts in a mine in eight different ways -- under torque/thrust control with and without hardened washers, belleville washers and tension equalization; in a conventional manner with and without a hardened washer. The various bolt groups were analyzed in terms of their tension uniformity and mean tension levels. Installing the bolts accurately with ? a hardened washer under the bolthead, and ? proper torque/thrust control resulted in the mast uniformly tensioned bolts -- with a coefficient of variation of only 14%, an improvement of 3 times over a conventional installation. Also, these bolts maintained a high tension level -- 80% of the installation tension, compared to 50% achieved conventionally.

Jan 1, 1982

By RUDULF KUDLICH

Pennsylvania anthracite coal is almost universally recognized to be the solid fuel best suited for domestic use when cleanliness , convenience and cost are considered . At various times and in various localities , however, conditions so affect the supply that it becomes insufficient or is too high in price and recourse must be had to other fuels as substitutes . In practically every district in the United States where anthracite has been the common domestic fuel , some other fuel is available as a substitute . In even the most severe climates such fuels are used either as emergency substitutes for anthracite , or as the ordinary domestic fuel . There may be some drawback to the use of such fuel , such as the need of more frequent attention to the furnace , smoke , soot and dust , in the case of solid fuels lower in price than anthracite , but these inconveniences must be accepted as necessary accompaniments to a decreased fuel bill . The cleanliness and ease of handling anthracite in the house must be considered in the light of a luxury and a higher cost of heating with this fuel must be expected . That a growing number of people are willing to pay for such added convenience is evident from the increasing mumber of heating installations using oil , gas and electricity , all of which are more convenient and usually more expensive even than anthracite .

Aug 1, 1923

By Wiliam L. Crentz

The importance of Somerset County, Pa., as a coal producer is due in large measure to the presence reserves of low-volatile bituminous coals. Although many coal beds of minable thickness are present, the important reserves are to be found in those beds underlying the Pittsburgh bed. The Kittenning beds and Freeport beds, which are responsible for the bulk of the present coal production in Somerset County and contain the largest reserves to meet future coal requirements, are usually thin and entirely free from impurities. The Pittsburgh bed, which has been such an important coal deposit in the coal areas immediately west and south of Somerset County, is of secondary importance in this county. Although generally rather friable, Somerset County coals have enjoyed wide receptability as excellent coals and to some extent have been utilized in the metallurgical market.

Jan 1, 1951

By J. H. East

"INTRODUCTION .Very little information regarding coal mining in Spain has been published in the American technical press, and few people realize the extent of this industry or the conditions under which coal is mined. The information in this publication was collected in 1945 and consists of personal observations in Spain, statistics, and other data of a, general nature obtained from official sources.Spain produces bituminous coal, lignite and anthracite, but the total tonnage mined is less than the national requirements. Before the war, an appreciable tonnages coal was imported from Great Britain under the Anglo-Spanish treaty, which rebated import duties and effectually prevented competition from any other foreign source. The war stopped the major part of the important of British coal and caused rapid expansion of the domestic sources, but this was not sufficient to supply the industrial demand. Coal that formerly was not acceptable to industry because of quality is now mined and marketed. The Government, allocates the better-grade bituininous coal to the various industries in accordance with the national importance of the work in which they are engaged; for example, the railroads are allotted 100 percent of their requirements, but cement companies can obtain only 25 percent.The Government offered to inducements to increase the production of coal of any class, but the larger part of the increased tonnage obtained was in inferior grades; as a result, the lignite production was taxed, while a bonus was paid for bituminous-coal production in excess of the 1942 tonnage.The anthracite and bituminous-coal areas were severely damaged during the Civil War and many experienced miners migrated to the lignite mines in eastern Spain. This has resulted in an acute shortage, particularly the Province of Oviedo where the most important bituminous-coal deposits are located."

Jan 1, 1947

By Thomas J. Peters

In 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 15,174-acre Sleeping Giant study area, including the 6,112-acre Wilderness Study Area (MT-075-111), in order to evaluate its identified mineral resources. The study area is located in Lewis and Clark County, MT, about 30 miles north of Helena. Sleeping Giant Mountain trends west-northwest from the Missouri to the eastern crest of Little Prickly Pear Canyon (the route of Interstate 15), and has several summits over 6,000 ft. Geologically, the area is in the Disturbed Belt, and a large block of Middle Precambrian metasedimentary siltstone and underlying shale has been thrust northeast over younger, sedimentdry volcanic and intrusive rocks.

Jan 1, 1988

By F. R. Cattoir, T. A. Sullivan

Commercial uranium metal was electrore fined to a high- purity product using molten- salt electrolytes in an inert atmosphere cell . Electrorefined uranium that contained , after consolidation , less than 30 ppm of metallic impurities was prepared . A method of leaching the electrolyte crystals to remove the salts was developed . Cathode current efficiencies from 90 to 100 percent were obtained . Two molten- salt electrolytes were prepared and evaluated : (1 ) lithium chloride - potassium chloride - uranium trichloride and ( 2 ) sodium chloridepotassium chloride - uranium trichloride . Very little difference was found in the purity of the uranium metal produced in either system . The lithium chloride - potassium chloride - uranium tri - chloride electrolyte was preferable from an operational standpoint .

Jan 1, 1964

Possible consequences of continuing internal political unrest and the imposition of foreign sanctions raise concerns about the traditional reliability of the Republic of South Africa as a major world supplier of important minerals. A recent Bureau of Mines' technical report (Open File Report 76-86) examined the impacts of temporary peacetime disruption scenarios for six key materials and mitigating options. Because of South Africa's dominant producer position for these minerals (except for cobalt), expansion of primary production capacity outside of South Africa is not a short term mitigative option. However, prospects of a longer term disruption would likely spur investment in capacity expansion in alternative Market Economy Country supply sources. This report identifies the resources, production costs, and burdens that would be placed on alternative MEC producers of chromium, cobalt, gold, manganese, and platinum-group minerals if South Africa's production were subject to a long term; disruption. When long term supplies from South African deposits are discounted, more than a few years reserves were found only for cobalt and manganese. Even for these two minerals, higher sustained prices would be required to increase manganese production capacity and to support means of cobalt transportation not through South Africa.

Jan 1, 1986

By R. Duncan Gardner

This paper describing the mining practice at the Harmony mine, Baker, daho, is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts in the United States. About 150 tons of copper ore containing 4 per cent copper, 0.001 ounce gold, and 0.1 ounce silver, is being produced daily from the Harmony mine by the shrinkage method of mining. The ore is taken by an aerial tramway 1/3 mile long to the mill, where it is concentrated. The concentrate is shipped 8 miles by truck to the railroad and thence by rail to Utah for smelting.

Jan 1, 1930

By E. M. Tignor

As a part of the program of promoting the conservation and efficient utilization of petroleum, studies are being made by engineers of the Bureau of Mines on secondary oil-recovery projects throughout the United States. In furthering that aim, engineering data concerning the reservoirs, methods of stimulating the production of oil, and other pertinent facts are collected, studied, and subsequently published so that others may profit by the experience gained. This report presents the results of a study made by engineers of the Franklin, Pa., office of the Bureau of Mines of secondary oil-recovery operations in the Boggs field, Spencer district, Roane County, W. Va., whore natural gas is injected into the reservoir to stimulate the production of oil from a so-called stripper field. The Boggs field, like most others in the Appalachian region, is one in which the major part of the natural energy that caused oil to flow through the reservoir to the producing wells during the primary stage of oil production has been dissipated. For all practical purposes, most of the oil produced in the Appalachian region at the present time can be considered to be from stripper fields. Consequently, secondary recovery methods are being used extensively in the oil-producing areas of New York, Pennsylvania, West Virginia, Ohio, and Kentucky for recovering some of the oil that was not produced by primary production methods.

Jan 1, 1949