Search Documents

By J. A. Eisele

The Bureau of Mines has reviewed the literature related to the recovery of A1203 (alumina) from coal ash. A small amount of unpublished data is also reported. Of the processes studied, the alkaline-sinter process is the most promising from a technical standpoint. However, owing to the high cost of processing coal ash, the dispersed location of powerplants, and the domestic availability of higher grade alternate materials, coal ash does not rank as a primary source material for replacing imported bauxite.

Jan 1, 1979

By C. P. Bowie

The Bureau of Mines has been conducting investigations with the view of determining the types of containers best adapted to the stor- age of oil. These investigations have shown that tanks composed wholly of steel give the best results. Where larger containers than it is feasible to build with steel are desired, concrete-lined reservoirs can be recommended for some grades of oil. Practically all such containers in use at present have wooden roofs and this type of construction is here described, although it is the belief of the writer that concrete roofs would be far more satisfactory in every way, and that the difference in cost between a concrete and a wooden roof would, as a rule, in a few years' time, be offset by a saving of oil and in cost of repairs and renewals.

Jan 1, 1918

Reduce well construction and operation costs associated with in situ leach mining while increasing mineral recovery. Approach To accommodate the size of centrifugal pumps presently in use, in situ leaching production wells are typically drilled to 6 inches in diameter, while monitor wells are drilled to measure 4 inches in diameter. However, in order to reduce the cost of drilling these larger diameter wells and to increase recovery, the Bureau has developed jet pumps which have smaller diameters than centrifugal pumps of the same capacity. This allows both production and monitor wells to be drilled smaller. Bureau estimates indicate that the cost of drilling a 3-inch-diameter production well at in situ leaching operations would be about 35 percent less than the cost of a 6-inch well. Similarly, the cost of drilling a 2-inch-diameter monitor well would be about 26 percent less than the cost of a 4-inch well. Such significant savings in the cost of drilling these wells would effect a substantial reduction in total capital cost. Use of the new jet pumps can also increase the percentage of recovery because less costly wells allow closer well spacings, improving the distribution of the leach solution. How the System Works After the borehole is cased, the new small-diameter jet pump, along with piping and accessories, is installed and connected to a centrifugal pumping unit on the surface. High-pressure water from the surface pump is forced through a nozzle into the venturi of the jet type pump injector. This jet action lifts the leach and mineral-bearing solution to the surface.

Jan 1, 1984

By Frank L. Hess

Vanadium, although widely spread in minute quantities through the crust of the earth, is found in few places sufficiently concentrated to be economically mined and prepared for use. Most rocks carry from a trace to a few hundredths of a per cent of vanadium oxide, and coal ash may carry about as much as the rocks, Much of the "coal" quoted in the literature as carrying vanadium has been asphaltite, and in other ccal the vanadium is of late introduction. The ash of the petroleums, though usually present in very small quantity, may carry a large percentage of vanadiun, so that production of vanadium from it has been seriously considered. Naturally the ashes of soze asphaltites similarly carry vanadium.' The great deposit at Minasragra, Peru, to which further reference will be made, is probably an altered asphaltite. Ilmenite and cther iron minerals usually carry vanadium 10 and some has been saved from the minette ores of France. 11 Many veins that carry lead copper and zinc minerals also carry a little vanadium, which, especially if the veins are in a comparatively dry region, such as the southwestern United States, northern Mexico, Northern Rhodesia, Southwest Africa, or Spain, collects in the oxidized parts of the veins as vanadinite,

Apr 1, 1932

By Carlton E. Brown

Inquiries and instructional work on the determination of the number concentration of dust in atmospheres known or suspected to contain pneumoconiosis (silicosis and asbestosis) - producing particulate matter indicate a need for a description of the impinger method used by the Bureau of Mines. The impinger method consists of the collection of dust in a liquid medium and the counting under the microscope of the particles in a known portion of this liquid. The dust-collecting device is called an impinger. The dust in the air drawn through this collector at a known rate impinges at high velocity upon a smooth surface under a bubbling column of liquid. The dust is either picked up from this surface by the liquid or removed from the air as it passes through the liquid.

Jan 1, 1938

By William J. Campbell

One of the principal objectives of the Bureau of Mines program for developing super refractory materials is to obtain fundamental data on the physical properties of refractory oxides. This particular investigation obtained accurate thermal expansion coefficients for alpha alumina and evaluated, critically, those coefficients with other published values. High-temperature X-ray diffractometer measurements, by the Bureau, showed that alpha alumina expands anisotropically with expansion parallel to the c axis approximately 10 percent greater than parallel to the a axis. Thermal expansion characteristics of four different alumina samples were determined up to 1,200° C.; the results are presented in both tabular and graphical form. The combined random and systematic errors in the measurements are considered less than 3 percent above 500° C, and approximately 2 percent at 1,000° C. No differences in expansion were observed between the samples or between the heating or cooling cycles.

Jan 1, 1961

By R. S. Dean

The principle of explosive crushing depends upon the fact that an expandable substance contained within the pores of a solid body will disrupt such a body upon expansion. Such expansion may be obtained by the detonation of an explosive or by the sudden release of pressure of a superheated liquid. That this principle of disruption may be applied to minerals rests on the fact that cracks, cleavage planes, and pores exist in all minerals to an extent hardly conceived possible heretofore. Crushing by this method takes advantage of forces applied from within the mineral rather than from forces applied from without. The application of a force from within would appear to be more effective.

Jan 1, 1932

By J. A. Kosek

Work has been carried out under Bureau of Mines Contract HO 395132 to develop improved sensor cells for use in direct-reading detectors and diffusion exposure meters. A pumped CO sensor cell was developed which has a shorter response time, improved temperature cycle characteristics, and improved linearity and stability at high CO concentrations. Diffusion CO sensor cells have shown good response level stability and linearity up to 1000 ppm. In addition, a new sensor cell catalyst has been developed for NO2 sensor cells which has a much shorter response time and improved response stability characteristics.

Jan 1, 1982

By Henry M. Harris

The Bureau of Mines investigated a glass containing approximately 17 percent lithia and 83 percent silica to establish a method of devitrifying cast and rolled shapes. Glass shapes with high strength were made by melting, forming, and rapid cooling of the composition, and the shapes subsequently were converted to a crystalline condition by heat treatment. The best devitrification schedule included rapid cooling of the glass to below 300° C, followed by reheating at a rate of 50° to 400° C per hour, depending on the size of the shape, followed by a of 60 to 70 hours at 500° C and another period of 15 hours at 800° C. attempts to use faster heating rates or slow cooling to accomplish devitrification in deformation of the shapes. The crystalline shapes had flexural strengths that averaged over 33,000 psi, achieved with an annealing time of 60 to 70 hours at 500° C.

Jan 1, 1965

By H. W. St. Clair

This study of the rate of evaporation of zinc was undertaken as a part, of a general investigation on refining mixtures of metals resulting from melting reclaimed scrap. One of the methods by which the more volatile metals, such as zinc, magnesium, and cadmium, may be separated is by distillation. Distillation may be carried out at lower temperatures if it is done in an evacuated enclosure. The immediate purpose of the present investigation was to determine accurately the effect of temperature, pressure, and other factors on the rate of evaporation of zinc.

Jan 1, 1950

By P. L. Woolf

An investigation was conducted to evaluate the use of a formcoke as the total fuel in the Bureau of Mines experimental blast furnace. The formcoke performed very satisfactorily, and comparisons made with a metallurgical coke showed that the performance with the formcoke was somewhat superior under the experimental conditions used.

Jan 1, 1966

By A. B. Needham

Graphite is a raw .material of considerable importance in both waxy and peace. Two types of graphite, classified according to particle size as flake and fines, are used, but the former is in much greater demand. The principal wartime use of graphite is in the manufacture of crucibles for melting brass and special alloys of copper and steel. Other uses in both peace and war are as lubricants, for foundry facings, and in paints, electrodes, batteries, motor and generator brushes, and a variety of other commodities. . This paper describes the operations of the Southwestern Graphite Co. of Los Angeles, Calif., which produces both flake and fine graphite from a property in Burnet County, Tex.

Jan 1, 1946

By Raymond M. Stateham

Climatic conditions are compared with roof fall occurrence from April 1, 1972, to December 31, 1975, by the Bureau of Mines. These comparisons indicate that humidity has a strong influence on roof fall occurrence rates. Cubic regression techniques are used to develop best fit curves. Statistical analysis of these curves indicate that both are sinusoidal and exhibit positive correlation with each other. The sine waves have a period of 1 year with maximum and minimum inflection points in August and February.

Jan 1, 1978

By Elizabeth A. Johnson

The vaporization thermodynamics of the aluminum-silicon carbides Al4SiC4 and Al8SiC7 were studied by the Bureau of Mines over the temperature range of approximately 1,500 to 1,700 K. Vapor pressures were measured by a Knudsen effusion-mass spectrometry technique in which powdered samples were effused from graphite crucibles through small orifices. For each compound, a total of six orifice diameters was tested to verify equilibrium within the cell. Aluminum, mass number 27, was the only vapor species detected over the range 4 to 200 amu. Experimental results are based on the following equations for incongruent decomposition: A14SiC4(cr) - 4A1(g) + SiC(a,hex) + 3C(gr); Al8SiC7(cr) - 8A1(g) + SiC(a,hex) + 6C(gr). The observed vapor pressure-temperature relationships determined with a cell orifice area of 2.0 x 10-3 cm2 for Al4SiC4 and 1.81 x 10-3 cm2 for A18SiC7 are the following: Log P - (-18,682/T) + 12.476, for Al4SiC4 (1,550 to 1,643 K) and Log P = (-19,308/T) + 12.421, for Al8SiC7 (1,526 to 1,784 K), with P in pascals and T in kelvins. Third-law analysis of the data provided the following heats of formation: A14SiC4 ?H at 298.15 K - -50.0 kcal/mol and A18SiC7 ?H at 298.15 K - -92.1 kcal/mol.

Jan 1, 2011

By Joseph M. Pugliese

This work was done by the Bureau of Mines to provide quarry operators with an uncomplicated, first-approximation method for designing blast patterns, considering geologic structure, and to show the valid use of the technique by comparing drill and blast pattern dimensions used in the quarry with those determined by the presented method. The author visited 12 limestone and dolomite quarries in Ohio (Adam, Crawford, and Highland Counties), Wisconsin (Milwaukee, Racine, and Waukesha Counties), and Minnesota (Fillmore, Olmsted, and Wabasha Counties); observed the blasting practices; studied the major geologic features; and after discussion with the quarry managers, foremen, and blasters, compared the quarry blasting patterns with those as calculated by the empirical formulas (after R. L. Ash), with geologic structural considerations. When geologic structure such as bedding, jointing, folding, and caves, as well as explosive properties and field performance characteristics are accounted for in a manner suggested by the research, the presented empirical formulas may be used as a good first approximation. The included steps in planning a blast design and generalized blast patterns should be of help to the quarry operator. Design changes are recommended for those quarries where problems are occurring.

Jan 1, 1972

By A. E. Isaacson

The U.S. Bureau of Mines determined the effect of common sulfide minerals on the corrosion rates of various types of ferrous alloy grinding media. Data obtained from this study will aid in determining the contribution of any electrochemical reactions between sulfide minerals and grinding media to the total grinding media consumption. Common sulfide minerals used in this study were chalcopyrite, galena, and sphalerite. In the presence of oxygen, chalcopyrite was found to increase the corrosion rate, galena was found to decrease the corrosion rate, and the effect of sphalerite was dependent upon the type of grinding media. Possible electrochemical reactions of these minerals in the presence of grinding media are suggested.

Jan 1, 1989

By R. L. Hopkins, H. T. Rall, H. J. Coleman, C. J. Thompson

Two methods were tested for separating sulfur compounds in certain petroleum fractions into types . Such separation is preliminary to identifying the compounds . Each method involved extraction of sulfides from petroleum sulfur concentrates . In the first method , the sulfur concentrate was reacted with methyl - ptoluenesulfonate to form sulfonium compounds from which unreacted portions of the sample were removed by washing with solvent . The sulfides then were recovered by heating the sulfonium compounds with anhydrous triethanolamine . The second method consisted of passing anhydrous hydrogen iodide into a n-butane solution of the sample cooled in dry ice , whereupon the hydrogen iodide adducted with the sulfides to form sulfonium compounds . These adducts separated as crystalline solids or , more frequently , as glassy viscous liquids . The sulfide was regenerated by adding water to the filtered sulfonium compound and was recovered by steam distillation or by extraction with pentane . These methods have been evaluated , using individual pure sulfur compounds and blends of sulfur compounds . They also have been applied successfully to separating sulfides from sulfur concentrates derived from petroleum fractions .

Jan 1, 1964

By P. D. Tracy, M. W. Von Bernewitz

"IntroductionA study of 256 coal-mine explosions, which occurred during the period 1909-1924 killed 4113 men and injured 570 others, reveals the fact that there are the critical times of day when explosions are most likely to occur, and when corresponding care should be exercised to guard against disaster. Of these 256 explosions, 83 straight as explosions, 89 were straight coal-dust explosions, and 81 were mixed gas and dust explosions, while three were undetermined.It has been determined from the times given in these reports (in several cases no times were given,that the critical period in the morning ranges between 6 and 9 o'clock when 83 explosions took place with a peal. at 7;30 o'clock. Of these 55 were straight gas explosions, the remainder being either coal dust or mixed gas and coal dust explosions. The critical period in the afternoon or early ranges between 3 and 7 o'clock, when 113 explosions took place, with a peak at 6 o'clock. Of these, 87 wore straight coal-dust explosions the remainder being neither gas or mixed gas and coal-dust explosions. Between these morning and evening periods is one which might be called the noon period - that is, from 11m to 7. p. m. - when 26 explosions occurred while some of these were normal type of explosions - that is, as to causes - others were of unusual cause and character, and. are discussed later. A number of explosions (29 in all) took place during mid-afternoon, late at night, and early in the morning - that is, after midnight."

Sep 1, 1924

By M. J. Ferrante

A process was investigated for preparing Specification-grade nickel (containing less than 1 percent cobalt) by stripping it electrolytically from a nickel sulfate-boric acid solution and using the stripped electrolyte for the preferential dissolution of nickel from basic carbonates of nickel and cobalt. The basic carbonates were produced at the plant at Nicaro, Cuba, owned by the U.S. Government. Determination of the optimum conditions for deposition of Specification-grade nickel indicated that the upper limit of cobalt concentration was 0.1 gram per liter. The pH, temperature, and concentrations of nickel and boric acid in the electrolyte were not critical. An aluminum cathode and two lead anodes were used at a cathode current density of 1.2 amperes per square decimeter.

Jan 1, 1959

By LeRoy R. Curwick

This Bureau of Mines report presents the results of a study conducted to assess the domestic availability of chromium from superalloy and cast heat- and corrosion-resistant alloy scrap material. Six alloy classes included in this survey were investment cast, hardfacing, and wrought nickel- and cobalt-base alloys, wrought nickel-iron-base alloys, and heat- and corrosion-resistant alloy castings. Data were collected for 1976 on metallic scrap generation, use patterns, and production practices for these alloy producing and using industries. A model was developed that allowed an assessment of the materials flow circuits within the industries that produce these alloys. The types, amounts, sources, secondary products, and ultimate destinations of chromium- containing metallic scrap for the six alloy classes were determined. Regarding the overall recycling efficiency of these alloy producing and using industries, of the 580.9 million pounds of scrap generated from these six alloy classes in 1976, about 72 percent (416.8 million pounds) was remelted by the same alloy-producing industries, about 18 percent (104.9 million pounds) was downgraded into stainless and low-alloy steels, about 3 percent (19.7 million pounds) was exported, and about 7 percent (39.5 million pounds) was lost through landfill or other disposal or service wastage. The lost material is primarily contaminated oxides for which recovery is currently uneconomic. However, the 124.6 million pounds of scrap material downgraded or exported in 197b contained potentially recoverable critical strategic elements. The amount of scrap material lost to the six alloy-producing industries in this manner contained 22.1 million pounds of chromium, 53.4 million pounds of nickel, 5.9 million pounds of cobalt, 35.9 million pounds of iron, and 7.3 million pounds of other alloying elements.

Jan 1, 1980