Search Documents

By C. H. Riggs

This report of a petroleum-engineering study of the Flat Rock oil field, Osage County, Okla., describes the geology, reviews the production history, and estimates remaining oil reserves. The Flat Rock field in the southeastern corner of Osage County approximately 6 miles northwest of Tulsa. Okla., was discovered in November 1904. The field was one of the first of many Bartlesville-sand fields developed in eastern Osage County during the early part of the 20th century. Although substantial oil reserves remain in the pressure depleted sands in some parts of the field, their economic recovery by water flooding will require careful consideration of the many factors involved.

Jan 1, 1954

By C. W. Vierrether

Tailings from the Pea Ridge iron mine contain significant amounts of apatite, which has rare-earth element values associated with it. In association with the recovery of rare-earth minerals as a secondary resource, the U.S. Bureau of Mines conducted an investigation on the recover ability of the rare-earth minerals from these tailings. The mill tailings were subjected to a phosphate flotation to separate the apatite from other constituents. More than 70-pct recovery of the rare-earth values was achieved. Based on mineralogical characterization and prior analysis of rare-earth-bearing breccia pipe material at Pea Ridge, it is proposed that processing this phosphate concentrate on a vanner table would yield up to a 95-pct recovery of the rare earths in the concentrate, with the apatite reporting to the tailings. Intensive ore microscopy studies of the original tailings to the flotation products led to the identification of monazite, xenotime, and rare-earth-enriched apatite as the major rare-earth-bearing minerals in the tailings.

Jan 1, 2010

By C. I. Pierce

The Bureau of Mines used an electrolytic tank model to investigate the response of guard electrodes of different dimensions under different simulated reservoir conditions. Sandstone disks from the Berea and Connellsville Formations were used as resistive beds in the model, and agar gel or water was used as conductive beds. In the experiments, bed thickness, hole diameter, mud resistivity, and bed resistivity were varied. The guard electrode is an excellent tool for determining true bed resistivity in the thin-bedded oil reservoirs of the Appalachian area. Vertical resolution and resistivity values are good when there is little or no invasion. Resistivity values are near true bed resistivity in beds thicker than about six hole diameters when the electrode-to-hole-diameter ratio is close to 1. However, low-resistivity muds cause false peaks to appear on the logs near bed boundaries in thick beds, and for resistive beds having a thickness approximately three to five times the hole diameter, apparent resistivities tend to be excessively high when mud resistivity is low.

Jan 1, 1966

By G. A. Appell

"INTRODUCTION During the summer of 1945, the Bureau of Mines conducted an investigation and program of churn drilling near the village of Tennyson in Grant County, Wis. The work was undertaken as part of a general investigation of the zinc-producing area of southwestern Wisconsin at a time when all effort was being made to increase the production of metals important to the war program.The area for special investigation was selected on the basis of favorable structural disclosures, evidence of widespread zinc mineralization, absence of any great amount of exploration to depth beneath the productive shallow workings, and the favorable results of several churn-drill holes in the village of Tennyson.During the Bureau's investigation, 30 churn-drill holes aggregating5,888 feet were completed.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to-the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual. Investigative work, and prepares the final report.The work described herein was accomplished under the direct supervision of Francis C. Lincoln and the author, mining engineers of the Bureau of Mines. Final data on the investigation were prepared under the direction of Edward F. Fitzhugh, Jr., chief Minneapolis Division, Mining Branch."

Jun 1, 1947

By Susan M. White

Increased coal production, wider use of indiscriminate mining techniques, improved cleaning methods, and greater emphasis on clean fuels is increasing the rate at which wastes accumulate Over the next several years, Colorado Plateau underground coal production is predicted to increase. Currently, mine refuse is deposited in canyons or lowland areas near mines. This study presents information on the nature of coal refuse and disposal practices on the Colorado Plateau. Samples were collected and analyzed to provide information to help formulate alternative methods for reclaiming refuse piles. The analyses were based on determining the capability of unmodified refuse to provide a suitable medium for plant growth. Local topsoils which would be used in reclamation were used as standards. Potential environmental hazards were assessed also. A general cost analysis was done for both surface and underground disposal and the advantages and disadvantages of each were assessed. Several problems were identified which, if solved, would increase the effectiveness of state regulatory programs.

Jan 1, 1982

By L. L. Oden

The Bureau of Mines is conducting research to develop methanation catalysts for converting synthesis gas derived from coal to synthetic natural gas. This report describes a method to prepare supported Raney nickel coatings by dipping screen-covered nickel sheet in molten aluminum-nickel alloy. Coatings were formed at 1,050° C that were comparable in thickness, composition, microstructure, and catalytic properties to flame-sprayed commercially pre-pared Raney nickel. A molten salt comprising cryolite-8 wt-pct LiF was employed over the molten metal bath to clean and preheat the substrates, to protect the metal bath from oxidation, and to heattreat the coated specimens. Immediately following heat treatment, specimens were quenched to 700° C in a molten salt bath containing CaC12-34.5 wt-pct NaCl, which also functioned to remove the insoluble occluded fluoride salt.

Jan 1, 1976

By E. J. Kloos, R. H. Schutz, B. I. Ferber

To Assist users in the selection of reliable and satisfactory respiratory protective devices, the Bureau of Mines has established five schedules of minimum performance requirements for the approval of respirators . The current revisions of these schedules include 13D for self-contained breathing apparatus, 14F for gas masks , 19B and the amendments to 19B for suppliedair respirators , 21B for dust , fume, and mist respirators , and 23B for chemical cartridge respirators . Copies of these schedules may be obtained from the Bureau of Mines, Publications Distribution Section, 4800 Forbes Avenue, Pittsburgh , Pa . , 15213 . Approval tests on respirators are performed only at the request of the manufacturer of the respirator and at his expense. If the device meets the approval requirements , a certificate of approval is granted on the complete respirator. This certificate states that as long as the respirator is manufactured as originally approved, or in accordance with any changes covered by an extension of the original approval, the manufacturer may advertise and sell his respirator as being approved by the Bureau of Mines. Many industries and regulatory agencies require that respirators approved by the Bureau of Mines be used where respiratory protection is needed. The Bureau of Mines, however, has no regulatory power over the use of the respirators that it approves. It acts as an impartial testing agency to insure the availability of suitable and safe respirators. At frequent intervals, the Bureau of Mines purchases approved respirators and replacement parts on the open market. These are examined for conformity to the approved status, and are checked to insure that the manufacturer's production facilities are maintaining a satisfactory quality control .

Jan 1, 1966

By E. J. Kloos, R. H. Schutz, B. I. Ferber

To protective devices, the Bureau of Mines has established five schedules of minimum performance requirements for the approval of respirators. The current revisions of these schedules include 13D for self-contained breathing apparatus, 14F for gas masks, 19B and the amendments to 19B for supplied- air respirators, 21B for dust, fume, and mist respirators, and 23B for chemical cartridge respirators. Copies of these schedules may be obtained from the Bureau of Mines, Publications Distribution Section, 4800 Forbes Avenue, Pitts- burgh, Pa., 15213. Approval tests on respirators are performed only at the request of the manufacturer of the respirator and at his expense. If the device meets the approval requirements, a certificate of approval is granted on the complete respirator. This certificate states that as long as the respirator is manufactured as originally approved, or in accordance with any changes covered by an exten- sion of the original approval, the manufacturer may advertise and sell his respirator as being approved by the Bureau of Mines. Many industries and regulatory agencies require that respirators approved by the Bureau of Mines be used where respiratory protection is needed. The Bureau of Mines, how- ever, has no regulatory power over the use of the respirators that it approves. It acts as an impartial testing agency to insure the availability of suitable and safe respirators. At frequent intervals, the Bureau of Mines purchases approved respirators and replacement parts on the open market. These are examined for conformity to the approved status, and are checked to insure that the manufacturer's pro- duction facilities are maintaining a satisfactory quality control.

Oct 1, 1965

By Gerald W. Elger

This report describes development of the fusion-leach crystallization precipitation process for producing a hafnium content feed material for hafnium-zirconium separation plants. Mixtures of zircon, potassium silicofluoride, and potassium carbonate (or potassium chloride) were fused to prepare soluble potassium zirconium hexafluoride-potassium hafnium hexafluoride salts. High extraction of these salts was obtained by countercurrent leaching the fused material in dilute hydrofluoric acid. About one-half of the hafnium was recovered in hafnium-enriched mother liquor by cooling clarified lead: liquor to crystallize most of the zirconium salt. Additional hafnium was recovered from the primary crystals in a multiple dissolution-recrystallization step. Hafnium-enriched oxides having a hafnium-zirconium ratio of more than three times that of zircon were precipitated from the combined mother liquors. The hafnium and zirconium recoveries in the precipitate were 83 and 24 percent, respectively. About 71 percent of the zirconium and the remainder of the hafnium were recovered in potassium zirconium hexafluoride crystals of low-hafnium content.

Jan 1, 1966

By Dennis A. Hansen

The solubility of anhydrous aluminum chloride in solutions of titanium tetrachloride and vanadium tetrachloride was determined as part of a re-search project-by the Bureau of Mines to make a homogeneous alloy sponge of titanium, vanadium, and aluminum. Solubility curves were established using an autoclave at 75°, 100°, 125°, and 150° C. The solubility of AJC13 in TiC14 is 0.2 wt pct at 75° C; it increases to 18.3 wt pct at 150° C. The data concur with data from earlier researchers of this bi-nary system for 75° to 125° C. For the VC14-AlC13 binary system the solubility of AlC13 is 0.1 wt pct at 75° C, increasing to 1.6 wt pct at 150° C. For the TiC14-AlClrVC14 ternary system the solubility of AlC13 decreases from the values found with a pure TiC14-AlC13 system to the lower values found with a pure VC14-AlC13 system at the respective temperatures.

Jan 1, 1986

By S. P. Kinney

During 1925, at Holt, Ala., the United States Bureau of Mines made a study of the composition of the gases at four elevations in the shaft of a furnace producing foundry iron. A report3 of the work was published in 1927. Some of the results of this investigation are shown in Figure 1. As indicated, the gas at the center of the shaft is low in CO2 content, while the gas in the vicinity of the wall is higher in CO2. The composition of the gases at the top and at the center of the stock column was not far different from the composition of the gas at the top of the bosh. The investigation indicated clearly that lean gas was channeling through the center of the column. More recently the study was enlarged in scope to include investigation of a furnace operating on Lake Superior ores in the Chicago district. A series of planes between the stock line and tuyères was surveyed. Means and apparatus were developed for obtaining, between the inwall and the center of the furnace, the gas composition, gas velocity, and temperature on each plane. A complete report4 of the investigation has recently been published.

Jan 1, 1929

By Northcutt Ely

This volume summarizes mining and petroleum legislation in 30 jurisdictions of the Western Hemisphere. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes: First, identification of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis of the laws governing mines and quarries and their products; and third, analysis of laws applicable to natural gas, petroleum, and related materials. Where pertinent, sections dealing with historical background or administration have been added. In countries where minerals are subject to control of States or Provinces, those areas are considered separately from the central government.

Jan 1, 1970

By J. W. Griflith, P. A. Mack, C. M. Lang, S. Riling

"N-acetyl-beta(B)-D-glucosaminidase is a N-acetyl-beta((B)-D-glucosaminidase enzyme se¬creted by alveolar macrophages in response to phagocytosis of particulate material. Alveolar macrophages participate in the degradation and fibrosis of pulmonary tissue that results in pneumoconiosis. Known quantities of four characterized respirable dusts were bronchoscopically placed into the right caudal lung lobe of macaque monkeys. Bronchoalveolar lavage (BAL) samples were collected from dust-exposed right lung and unexposed left lung of the same individuals at 2-week intervals for 12 weeks after dust instillation. The samples were tested for N-acetyl-B-D-glucosaminidase activity to determine if the enzyme levels could serve as an indicator of pulmonary injury induced by generic coal dusts when compared to known fibrogenic and nuisance dusts. Installation of generic quartz, anthracite, or TiO2 dusts produced significant elevations of enzyme activity and increased numbers of macrophages in the dust-exposed lobes. Elevations in enzymatic activity and macrophage numbers were greatest in response to generic quartz dust. These results suggest that quantitative levels of N-acetyl-B-D-glucosaminidase activity may be a useful indicator of acute and chronic lung injury following exposure to fibrogenic and nonfibrogenic dusts.IntroductionCoal workers pneumoconiosis (CWP) is an occupational pulmonary disease associated with the inhalation of coal mine dust. An important external factor in the development of CWP is the composition of the respirable coal mine dust. A cause-and-effect relationship exists between coal mine dust and CWP, but it has not been shown that exposure to generic coal dusts will cause CWP [12]. Numerous immunological, biochemical, and cellular changes occur in CWP; however, in this study, only N-acetyl-beta(B)-D-glucosaminidase (NAGase), protein, and alveolar macrophages (AM) will be examined [7, 32, 33]."

Dec 1, 1996

By Thomas O. Llewellyn

This U.S. Bureau of Mines (USBM) report presents a concise review on sources, processes, supply, and historical use patterns of domestic cadmium. It also covers a preliminary estimated cadmium material flow for the year 1989. This preliminary study contains information on cadmium and cadmium-bearing products in the United States. The data in this report were obtained from both published and/or unpublished sources of information. However, in order to estimate the fate of cadmium in each operation or application stage, some assumptions, judgments, and correlations were made by the USBM in an attempt to determine the material flows losses.

Jan 1, 1994

The Bureau of Mines is establishing design criteria for effective roof support systems and is developing technology to improve mine planning and design. Geologic studies, surface and underground mine monitoring, and laboratory evaluations were conducted. The seven papers in this proceedings Information Circular present results of several investigations. Addressed are problems existing in both longwall and multiple-seam mines. Discussions include the effect of dewatering at a longwall mine site in the Pittsburgh coal seam and the effect of chain pillars on subsidence. Other results are measurement and characterization of longwall rock mass movement and an integrated design for stability in multiple-seam mining.

Jan 1, 1987

By M. A. Mahtab

This report presents a new procedure for analyzing the orientations of rock fractures in an engineering site. This procedure, coded in a computer program, identifies clusters or groupings among the fracture orientations and calculates (1) the mean orientation of the fractures within each cluster and (2) the dispersion or scatter among these fracture orientations. Data points are represented by intersections of joint normals with the upper hemisphere, which is divided into 100 equal-area quadrilateral patches. The points in adjacent patches where the Poisson distribution test shows significant concentrations are assigned to a single cluster. For a cluster whose fracture orientations follow Arnold's hemispherical normal distribution, a confidence interval for the fracture orientation mean is calculated by applying Fisher's estimates. The technique is applied to the treatment of three examples.

Jan 1, 1972

By A. J. Leighton

An improved mathematical model with the attendant computer program to calculate multiphase fluid flow in petroleum reservoirs is presented. The model is used to simulate the behavior when a fluid is used to displace hydro-carbon fluids in a reservoir. The method is an expansion of a previously published method, in Bureau of Mines RI 7011, but handles constant injection rate as an alternative to constant pressure. Program documentation is provided along with thorough explanations of the added program features. Using the program, the petroleum engineer can calculate oil recoveries for different flood patterns and operating conditions and select the conditions most likely to optimize recovery. Experience with the previous model demonstrated the need for the improvements in order to simulate reservoir behavior more accurately. The improved method will result in improved oil recovery. In this paper, the significant improvements are described in detail so that anyone interested can put the program to use.

Jan 1, 1975

Overexposure to noise is a widespread, serious health hazard in the mining industry, and causes hearing losses to a large percentage of the mining population. Recognizing this fact, the Bureau has a major on-going research effort to address this problem area. These proceedings include an overview of the Bureau noise control program and summarize nine selected noise control research programs.

Jan 1, 1984

By William H. Lyon

In 1950 the Program Staff of the Department of the Interior undertook an exploratory study in the projection of energy requirements of the nation. This work was reported in Bureau of Mines Information Circular 7582 by H. J. Barnett. In that preliminary study Mr. Barnett, after exploring the nature of the energy economy in some detail, evolved a method for estimating how much energy will be required in the future, based on estimates of trends in efficiency of energy utilization in specific applications, the physical output of specific energy-consuming industries, size of the population, productivity advances in the economy at large, consumer preferences, and other factors. Considerable new information was developed regarding the nature of energy demands and the possible levels of requirements for each fuel under various assumed business conditions. The study analyzed the interrelationships, including substitutions, among the fuels and emphasized the need for viewing the energy economy as an integrated albeit complex whole. This exploratory study showed a need for a single comprehensive statistical re-port that would assemble and show in a uniform manner the diverse published statistical data on energy commodities now scattered through many publications. A particularly important need was for a set of historical statistics showing the production and consumption of all energy on a B.t.u. basis. As the prospective size and nature of the future energy requirements of the nation are matters of continuing importance, this report was prepared to assist further investigations of the subject. In this report the authors undertake to assemble and present in tabular form, on a uniform basis, the production and use of each of the fuels and electric energy in the United states for three census years -1929, 1939, and 1947. The year 1947, rather than a later year, was selected because it is the most recent year for which census data are available showing the consumption of fuel by each of the manufacturing industries. It is hoped that making data for these 3 years available in one re-port will provide the needed statistical background for further studies of fuel requirements and supplies.

Jan 1, 1951

By A. W. Deurbrouck

The separations achieved by eight conventional cyclone washers have been evaluated to determine their performance when processing intermediate size coal of 28 mesh bottom size. The dense-medium cyclones provided efficient, sharp separations in treating feeds of up to 44 percent of near-gravity material at separating specific gravities ranging from 1.42 to 1,55 (one separation of a secondary feed was made at 1.63). Complete washability analyses are shown by sizes of the composite feed to these cyclones. The magnetite losses per ton of coal processed ranged from 0.6 to 2.0 pounds; however, of the eight plants reporting losses, seven indicated magnetite losses were 1.1 pounds or less per ton of coal processed.

Jan 1, 1972