Search Documents

By R. R. May

A preliminary examination of the Houston strip-coal mine, situated on the Alaska Railroad at milepost 175 (61 rail miles north of Anchorage, Alaska) and a review of all available information resulting from early coal exploration activities in the area resulted in plans to investigate the coal-bearing formations at depth by means of diamond core drilling to indicate the existence of additional reserves of coal in close proximity to railroad transportation, where it would be quickly available to meet rapidly expanding military and civilian fuel requirements. From the date of mobilization of equipment, August 28, 1951, until date of suspension, August 18, 1952, 2,010 feet of diamond drilling was completed. Ten definable coal beds were cut, of which 2 appear to be persistent and minable over an area of approximately 1/2 square mile. Within this area the 2 minable beds contain approximately 5,000,000 tons of coal in place. Of the remaining beds, at least two others may be minable to the eastward near their projected outcrops; however, these and deeper beds (at least in the vicinity of the drill holes) lie beneath a zone of pressurized gas and brackish water. From a practical standpoint, continued development and utilization of the coal in this vicinity will depend on the operators' ingenuity in developing cheap mining methods and on diligent prospecting for strippable coal under the comparatively light glacial cover.

Jan 1, 1957

By Jr. Fish

As a part of a study of iron are resources in the Appalachians, 9 diamond drill holes aggregating 1,580.7 feet were drilled in a portion of the Butt Mountain area of northeastern Giles County, Virginia. Three hematitic sand-stone beds were intersected in the Clinton formation but only one was consistent in thickness and grade in all 9 drill holes. This bed averages 18.9 percent iron over an average thickness of 24 feet. The drill cores were logged and chemical analyses were made on 161 individual samples and 22 composite samples. Beneficiation studies were made of three composite hematitic sandstone samples each representing a separate bed containing 14.6, 19.8 and 20.0 per-cent iron. Major mineral constituents of the samples were hematite, quartz, and sericite.

Jan 1, 1967

By Richard G. Burdick

The Bureau of Mines conducted this research to determine the feasibility of using soil redox measurements, a relatively new method in mining geophysics, to locate or define a variety of conditions that are hazardous or otherwise of interest to the mining industry. The method was used in three widely separated areas in an attempt to de- fine subsurface concentrations of methane, the edges of coal-burn areas, and a hydrothermal vein set. Both a description of the method used and test cases are given in this report.

Jan 1, 1982

By R. V. Higgins

As part of a study of application of the Buckley-Leverett method to an analysis of oil-reservoir performance covering a wide range of relative permeabilities and oil saturations, a method has been devised for quickly deter-mining average water saturation at breakthrough from relative permeability data. The base for the relative permeability used in the report is either the permeability to air or the effective permeability to oil at the irreducible water saturation. The permeability to air also was used because of the large backlog of air permeabilities available to reservoir engineers. The basic data were calculated by an electronic computer and are presented in a single graph from which the point of breakthrough may be obtained. In this study the water saturation at the beginning of the depletion is the connate or interstitial or irreducible water saturation. These water saturations are considered to be synonymous and to have a practical value.

Jan 1, 1960

By F. S. Kendorski

This report covers the work on developing criteria for determining when a hazard exists when mining stratified mineral deposits beneath bodies of surface water. The nature of water bodies is considered, the disturbance to the strata induced by mining is described, inundation case histories reviewed, reasonable water inflows derived, and methods of mining to prevent or minimize the hazard are presented. Criteria are given whereby effected industries and agencies can recognize a potential hazard and plan a mine accordingly, releasing considerable mineral reserves otherwise considered unminable.

Jan 1, 1979

By Sabri Ergun

This report gives the result of investigations of coals of different rank, coal com¬ponents, chemically and thermally treated and irradiated coals, and sedimented organic matter. In most studies the arbitrary parameters obtained from the usual quantitative profile analyses are not given largely because they lack physical meaning. Instead comp interpretations are offered. X-ray patterns of high-volatile bituminous and lower rank coals are not self¬-sufficient for structural interpretation by the methods of analysis developed to date. The patterns of hydrogenated and dehydrogenated coals indicate that the basic change in the structure of bituminous coals with increase in rank is the conversion of alicyclic structures into aromatic layers. In low-rank anthracites the aromatic layers are about 10 A in size. The increase in rank is the result of coalescence of layers. High-rank anthracites have layer sizes of 25 to 40 A and exhibit the development of three-dimensional (hkl) reflections of graphite, indicating ordering of adjacent layers. In meta-anthracites the layers are > 1000 A and the basic structure is that of defective crystalline graphite. The well-known petrographic components in low-rank coals have different structures; the differences dissappear in low-volatile bituminous and higher rank coals. The patterns of sedimented organic matter, except impsonites, differ from those of coal hydrogen contents are high, and their X-ray patterns are consistent with those of structures. In contrast to normal coals, the patterns of uranium-bearing coals show increased diffuseness with decrease in hydrogen content. The diffuseness is accompanied by increase in the uranium content of the coal. It is very likely that high uranium-bearing coals have predominantly tetrahedral structures.

Jan 1, 1968

By David C. Minton

This paper describes in detail the cost of equipping and developing the Golden Belt mine, Yavapai County, Ariz. These costs should be typical of the average small gold mine in central Arizona which has been equipped with used machinery a, a minimum of capital expenditure. The conditions of remoteness, transportation, water, and power supply are about average for properties in the Bradshaw fountains and that vicinity. There are several mines in the district in the process of development and several dormant properties that might be opened in the future. The Golden Belt group of claims was taken over by the present management in May, 1931. Although some active development has been carried on in recent years, resumption of work at the old property required entire rehabilitation of the equipment and camp. As the water level had not been reached, there was no problem of dewatering. In the presentation of costs in this paper an evaluation of the cost of equipment and development work as taken over by the Golden Belt Mines, Inc., has been made. Enact data, however, on previous exploration and construction costs are lacking. The total cost of equipping and developing the mine to its present stage has been obtained by adding the disbursements of the present management to the above-mentioned evaluation. These costs do not include the cost of replacing camp, equipment destroyed by fires, of unsuccessful milling experiments, management, or obsolete equipment on the property.

Jan 1, 1933

By Michael J. Potter

Native asphalt was produced by five companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by White Uvalde Mines and by Azrock Industries Inc., Uvalde County, TX. In June, Azrock Industries was purchased by the R L. White Co. Gilsonite, a solidified hydrocarbon found only in Utah and Colorado, was mined by American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California); by Ziegler Chemical and Mineral Corp.; and by Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation) from properties in Uintah County, UT. Gilsonite is used for a variety of purposes including automobile bodysealer, light-weight aggregate for cement used in oil well drilling, asphaltic building board, protective coverings, anticorrosive paints, and roofing compounds.

Jan 1, 1985

By Louis A. Panek

Roof bolting has been known for many years, although the practice had very limited application before 1948. Since then, bolting has been introduced as a systematic method of support in more than 700 coal mines and more than 200 noncoalmines and other underground openings in rock. By far the greatest number of bolts are used to support bedded roof. This is largely because of their use in coal mines, although roof bolts are used in mining bedded deposits of all kinds -potash (New Mexico), trona (Wyoming), and ores of iron (Alabama), lead (Missouri), uranium (Utah), lead-zinc (Utah), and copper (Michigan and Arizona). Thus, bolting has been successfully employed to reinforce bedded roof under a wide range of conditions despite the limited knowledge of the principles involved. This report develops the basic principles of bolting bedded roof based on elementary beam theory and on the results of tests intended to prove or disprove certain fundamental premises. Specifically, the objectives were to gain an understanding of the function of the bolts and the behavior of bolted roof and to establish standard bolt patterns. A combination of theoretical and experimental analysis was employed. The experimental method consisted of testing mine -roof models in a centrifuge. The models, the test procedure, and the model-prototype relations are described in a companion report (1)2/. A second companion report presents a method for designing systems of vertical bolts to reinforce bedded roof (2).

Jan 1, 1956

By Charles T. Holland

ANALYSIS of 117 occurrences of bumps in coal mines shows that 67.6 percent are associated with pillar-line points.4 Slabbing and splitting pillars, development, and other unfavorable milling practices in abutment areas may be a contributory or the primary cause of bumps. The cure for pillar-line bumps is to recognize areas that can be expected to become highly stressed and to project the mining plan and operations to eliminate such areas insofar as possible. If such areas cannot be eliminated, then the mining plan and operations should be projected to avoid the necessity of disturbing these areas before the stresses have been dissipated.

Jan 1, 1954

By Howard P. Hamlin, John W. Sweeney

Shales , clays , and loess in Iowa were tested and evaluated to determine feasibility of producing lightweight aggregate by commercial rotary - kiln or sintering methods . Preliminary testing was conducted in a muffle furnace . Rotary - kiln tests were conducted in a 16 - inch by 14 - foot rotary kiln . Concrete cylinders and cubes were tested to determine qualities of the aggregate . Three samples made suitable lightweight aggregate by rotary - kiln methods and two by sintering .

Jan 1, 1964

By John A. Kost

Previous work performed under Contract H0220003 suggested that the mean incombustible content could be obtained with fewer samples and smaller samples without greatly increasing the sampling error. Under Modification No. 4 additional surveys were made in twelve coal mines, representing six states. Same 2,500 samples were collected, analyzed for incombustible content, and statistically evaluated. The earlier findings were substantiated.

Jan 1, 1975

By Gary E. Sherman

To aid the U.S. Army Corps of Engineers in their Resource Development Navigation Study of ten existing or proposed port sites in Alaska, the Bureau of Mines examined the potential for mineral development around three Alaska port sites: Iliamna Bay, Kotzebue, and Nome. The mineral deposits near Iliamna Bay include gold, copper, and iron. Development of minerals in this area will require the discovery of new deposits or the definition of additional are reserves at known deposits. The mineral deposits near Kotzebue are primarily gold, copper, coal, lead, and uranium. Based on the character of these deposits, it appears that development of a small-scale mine supplying coal for regional use is the most likely scenario in the near-term. The mineral deposits near Nome are primarily gold and copper. Development of small underground gold mines is possible, however it appears that expanded offshore gold dredging will have the greatest impact on the flow of freight and goods through the Nome port in the near term.

Jan 1, 2011

By J. R. Long

The Federal Bureau of Mines has pioneered the work of preparing ductile titanium on a large scale and has also determined the basic properties of this new and most interesting metal. A number of reports (1, 2, 3: 4, 5) have al-ready been published, and considerable interest has been aroused in a number of industrial and research laboratories. Some of these laboratories have also published results of their work on the pure metal. Although the properties of titanium itself are quite promising, it is apparent that considerable improvement may be expected by alloying titanium with other metals. That is, pure metals in general have shown relatively large improvements in properties when alloyed with other metals and titanium is not considered to be an exception to the rule. Therefore, the emphasis of the investigations now under way in the Federal Bureau of Mines Laboratories has been placed on the study of the alloys of titanium, particularly the titanium-rich alloys. While the main interest is in the properties of such alloys, proper direction and evaluation of the work require at least a rough outline of the phase boundaries of the alloy systems involved.

Jan 1, 1949

By D. E. Wolfson

Twenty-two samples of West Virginia coals were carbonized at 9000 C by the Bureau of Mines-American Gas Association (BM-AGA) method, and yields of products and physical properties of cokes were determined. Eighteen samples represented the Coa1burg, No. 2 Gas, No. 2 Gas and Peerless, Powellton, Eagle, Big Eagle, Lower Eagle, Sewell, Fire Creek, and Pocahontas No.6 beds in Fayette County, and four samples represented the Sewell and Fire Creek beds in Greenbrier County. Expansion characteristics of the majority of samples were determined in the Bureau of Mines sole-heated oven. Chemical analyses were determined for all coals. The coals in Fayette County are high-volatile A, medium-volatile, and low-volatile in rank, and the Greenbrier coals are medium-volatile in rank. Most of the coals are chemically suitable for metallurgical coking. All coke strength indices are within acceptable limits for metallurgical coking coals. All the high-volatile A coals contracted and the medium-and low-volatile coals expanded in the sole-heated oven expansion test.

Jan 1, 1966

By J. W. Miller

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and, from the data developed, to determine: (a) Which coals, either as mined or after beneficiation by conventional preparation, are suitable chemically under present standards for producing metallurgical coke. (b) Which coals require special and more intensive treatment in preparation than is now practiced. (c) Which coals cannot be considered potential sources of metallurgical coke, regardless of preparation. This report is one in a county series and describes the preparation characteristics of the coals of Logan County, W. Va. According to present-day standards for metallurgical coal, many believe that the sulfur content of the coal should not exceed 1.25 percent? Coal with more than this amount has been used for making metallurgical coke, especially when blended with coal containing less sulfur. In this series of reports 1.25 percent sulfur is used as a gage to determine whether or not a coal will be suited for metallurgical coke.

Jan 1, 1957

By J. D. Brown

The electron optics, vacuum system, and sample stage assembly for the Bureau of Mines? electron probe X-ray spectrograph were purchased. Four scanning curved-crystal spectrometers, two reflection- and two transmission-type, were designed and constructed by the authors. The reflection spectrometers are placed in a vacuum chamber for measurement of long-wave-length X-radiation. Detection, pulse-amplitude discrimination, and recording circuits are provided for the simultaneous measurement of four X-ray spectral lines. Minimum spot size is approximately 2 microns in diameter at 30 kilovolts and a sample-to-ground current of 5 x 10-8 ampere. At this voltage and current the limit of detection with reflection spectrometers is less than 0.05 weight-percent for most elements. The limit of detection for elements determined by transmission-type spectrometers, evaluated at 35 kilovolts and 5 x 10-8 ampere, is approximately 0.1 weight--percent for all elements having excitation voltages below 20 kilovolts. In general, reflection spectrometers exhibited satisfactory but poorer resolution than the transmission type, resolution of the spectrometers being limited primarily by crystal imperfections, with greater mosaic structure being introduced by the grinding process for the reflection crystals. Several applications of the electron probe X-ray spectrograph are described. Analysis of a uranium-steel is discussed in detail to illustrate calculation of composition from measured X-ray intensities.

Jan 1, 1962

By C. P. Mangelsdorf

When the finely bedded shale frequently encountered over coal seams experiences a separation, the material below the separation must behave like a beam or plate in that it must resist both bending and shear. Be-cause of the weakness in interlaminar shear inherent in such strata, shear deflections that are usually ignored in isotropic beam theory may account for a significant part of the total roof sag. Similarly, when a roof truss is installed in such a roof the upward displacement reducing the sag will have components due to shear as well as bending. Questions asked by mine operators about the installation of roof trusses frequently deal with optimum position, slope, and initial tension of the inclined chords. This Bureau of Mines report examines the effects of those chord parameters on the strain energy of both shear and bending and offers optimum values that will minimize the total strain energy of the immediate roof. Design charts are provided, several design examples are included, and the results are compared with current practice. The effects of in situ stresses are investigated and are shown to be equivalent to an additional load on the beam.

Jan 1, 1988

By G. S. Knoke

This report presents the results of a demonstration of the technical, economic, and environmental feasibility of hydraulic borehole mining of shallow oil sands. Borehole mining offers a method for extracting the oil sands with minimal disturbance to environmental quality because (1) no overburden is removed, (2) no waste rock piles are required, (3) the tailings can be backfilled into the borehole cavity, (4) the ground water quality should be undisturbed, (5) a closed-loop water system can be employed so that no surface streams are polluted, and (6) surface subsidence can be minimized by backfilling the mined cavities. This project consisted of two concurrent tasks: mining operations and environmental monitoring. To generate the environmental impact, nearly 1000 tons of oil sands were mined from two boreholes. Water quality and ground subsidence were monitored. No significant changes occurred in the chemical composition of the process water, indicating that the borehole mining process does not dissolve the mined material. The average subsidence in the immediate vicinity of the boreholes was about 1/2 inch, although some points were noted to be slightly elevated. In general, the amount of subsidence increased with time and decreased with distance from the bore-hole. A mining cost analysis was used to project an estimated cost for production mining of about $38 per barrel of oil.

Jan 1, 1980

By C. Edward Chamberlain

A Bureau of Mines procedure was developed for the analysis of volatile matter in airborne coal dust-rock dust mixtures prior to, and resulting from, coal mine fires and explosions. Dust in the 10-to 20-mg weight range can be analyzed. Volatile matter is determined by a greatly scaled-down version of the empirical macro-scale method used by the Bureau. The alkaline earth carbonates in the rock dust are dissolved in acid prior to the volatile matter determination of the residue, and the rock dust content is calculated from the analysis of calcium and magnesium by atomic absorption.

Jan 1, 1974