Search Documents

By Magnus Persson

ISO8662-4, “Hand-held portable power tools - Measurement of vibrations at the handle - Part 4: Grinders” is under revision. The new revision shall harmonize ISO 20643 “Mechanical vibration - Hand-held and hand-guided machinery - Principles for evaluation of vibration emission” which, among others, requires measurements in three directions and declared values related to the upper quartile of real-use vibration. To get the most suitable test method, a round robin test was made for evaluation of the two test methods proposed by the ad-hoc group working with this standard revision. Methods Seven laboratories measured the vibration from four grinders of different sizes, with and without autobalancing units. The laboratories come from universities, health & safety laboratories and grinder manufacturers. Two measurement methods are evaluated with respect to repeatability and reproducibility: 1. Grinding on a well-defined mild steel bar with depressed center wheels according to detailed test instructions. The test sequence starts and ends with 10 seconds of running the grinder in the air, when measuring the unbalance contribution to the vibration coming from the unbalance of the grinding wheel. Between these runs the average vibration during 60 seconds of grinding is measured. Three operators do five grinding tests per grinder. 2. Measurements using an aluminum unbalance disc similar to the one defined in ISO8662-4. Each operator runs the grinder four times, between each run the unbalance is moved 180 degrees to avoid variations caused by the play between the test wheel and the spindle. The averaging time is 10 seconds. Each grinder is tested by three operators. Repeatability is the spread within a lab between operators and over short time period for one machine and reproducibility is the spread between laboratories and over longer time periods for one machine. Instrumentation and transducer location are chosen according to ISO8662-4 and circulated test instructions. Results Both the repeatability and reproducibility is poor for the real grinding test, see figure 1. The coefficient of variation for repeatability is approximately 40% higher for the grinding test and the coefficient of reproducibility is 60% higher for the grinding test than for the unbalance disc test.

Jan 6, 2006

By D. R. Babich, E. R. Bauer

National Institute for Occupational Safety and Health (NIOSH) researchers are conducting a cross-sectional survey of equipment noise and worker noise exposures in the mining industry. Surface and underground limestone is one commodity recently surveyed. The sound levels of mining and processing equipment were recorded to identify noise sources. Full-shift worker noise exposures were completed to determine the exposure of various occupations. This paper presents the results of the noise research conducted in both underground and surface limestone mines, detailing the equipment likely to cause worker overexposures, and the occupations experiencing overexposures. Implications for worker noise exposure reduction are also reported.

By Kim M. Cornelius

Musculoskeletal injury is a term used to describe a wide range of soft tissue disorders which affect the nerves, tendons, and muscles. Common examples include lower back pain, tendonitis, and carpal tunnel syndrome. The majority of these injuries are not the result of sudden mishaps, but usually develop gradually from repeated wear and tear. Symptoms may first appear after weeks, months, or even years. Symptoms may result from many types of activities, performed at work or at home, and it is often difficult to attribute a single event. In fact, it is more common to identify the factors which may have contributed to the development of the condition. The terms repetitive strain injuries or cumulative trauma disorders (CTDs) have been commonly used to refer to disorders that have occurred due to work related activities (Putz-Anderson, 1988; Fraser, 1989). Three main risk factors contribute to CTDs: force, repetition, and awkward postures. Any one or combination of these may contribute to the development of CTDs. Therefore, the design of equipment in conjunction with the required tasks should attempt to reduce these risk factors. Examining the layout of the work area to help identify tasks which may contribute to cumulative trauma is necessary. The following list(Putz-Anderson, 1988), describes ergonomic concerns that, overall, should be minimized at the work area:

Jan 1, 1997

By Terry J. Close

A mineral resource survey of the 236-mil (611-km2) Hyalite-Porcupine-Buffalo Horn wilderness study area (RARE 11 Areas No. 1-155 G, Gallatin Divide; and H, Hyalite) between the Gallatin and Yellowstone rivers in Montana, indicates there are phosphate rock and petrified wood resources (fig. 1). The area also has some potential for oil, gas, and geothermal resources. Stone and alluvium are abundant but appear to have little potential for development because other sources are available nearer to markets.

Jan 1, 1981

By Ben E. Lindsly

The study of "bottom-hole' samples follow,-is in natural sequence the study of samples3 obtained under high pressures at the well heads of flowing wells. The principal object of this phase of gas-solubility research, started actively in January, 1530, was to gain a more accurate knowledge of the physical and chemical characteristics of the oil-gas mixtures that exist in natural reservoirs. In possession of actual data regarding the condition of the oil; the quantity of gas liberated from solution upon dimunition of pressure; and the relative volumetric proportions of gas to oil at various pressures throughout the flow string in a well, it should be possible to predict, with a fair degree of accuracy, what physical changes these mixtures would undergo throughout the life of a pool. Such information not only is important in designing flow strings in flowing wells but is important also in solving problems relating to pumping efficiency and the power required for pumping. Although certain fundamental rata Mere obtained in the stud of samples taken at the well head, "bottom-hole" samples are more representative of subsurface mixtures of oil and gas because they are obtained at reservoir temperatures, and before the oil has had the opportunity of intermingling with extraneous gas; that is, gas which either was not in solution originally, or which was liberated from solution at some higher pressure, and later became mired with the original undissolved gas.

Jan 1, 1933

By A. T. Coumbe

The first survey 3/ covering sales of liquefied petroleum gases was made in 1930 by the Bureau of Mines, which at the time was under the United States Department of Commerce. This original canvass covered national totals for 1922 through 1929, and most of the supply came from natural gasoline plants. The 1930 report showed approximate totals for butane and propane and for butane-propane mixtures and pentane grouped together. No attempt was made to breakdown the national sales by various uses until 1931, when the quantities for domestic or household consumption, gas manufacturing, and industrial requirements, including miscellaneous uses were indicated. As the market for these liquid petroleum gases expanded and as new uses came into importance, their respective quantities were shown separately in the annual survey. Sales for internal-combustion engine fuel and for raw material for chemical plants were first taken out of the industrial total in 1936. During World War II liquefied petroleum gases became important as feed stock diverted to synthetic rubber plants, and consequently the survey was broadened to cover this particular demand, beginning in 1944. Pentane was dropped from the survey after 1943, as, being liquid at atmospheric pressure, it is not considered as one of the liquefied petroleum gases and furthermore, the quantity reported made up less than 1 percent of the total sales. Thirteen producing companies reported to the Bureau in the first survey made in 1930, and in the 1952 canvass about 130 producers--petroleum refiners and natural gasoline companies--and about 1,300 dealers cooperated by filing schedules showing a breakdown of their sales. Their 1952 deliveries of approximately 4.5 billion gallons of liquefied petroleum gases were equivalent to about 3.4 billion gallons of gasoline or 3.1 billion gallons of distillate fuel oil.

Jan 1, 1954

By Calvin J. Konya

Overloaded blastholes and insufficient stemming are major factors in flyrock accidents at surface metal and non-metal mines, Accurate measurement of blasthole depth, stemming height, and water depth would reduce the overload and the probability of blow-out, flyrock, excessive ground vibration, and airblast. Problems result because current measuring systems are inaccurate and often difficult to used A literature survey determined measurement techniques and blasting parameters prior to 1970. Similar data were gathered for current practices in 11 iron mines, 30 copper mines, and 92 quarries. Most operations used a cloth tape to measure borehole depth and stemming height; approximately 10% of the operations had dry blastholes. Alternate measurement techniques were evaluated and discussed. Candidate measuring techniques with best potential for improvement over the present weighted tape method are disposable tapes or string chains, automated readout tapes, modified sludge level indicators and acoustic resonance methods.

Jan 1, 1981

By H. D. Jacobs

A process for recovering both iron and manganese from four manganiferous ores of the Cuyuna Range was evaluated. It comprised: (1) Low-temperature gaseous reduction to convert nonmagnetic iron minerals to magnetite and manganic minerals to manganous oxide, (2) acid leaching to extract manganese, and (3) magnetic separation to reclaim iron from the leach residue. Iron recoveries from the magnetic products ranged from 70 percent to 90 percent; manganese recoveries from leach filtrates ranged from 75 percent to 95 percent. Two ores, from the Hillcrest and South Alstead properties, yielded magnetic products considered adequate for use as blast furnace feed. Although good yields of manganese were attained on all ores, appreciable iron accompanied the manganese into solution. Previous work, however, has shown that this iron can be precipitated almost quantitatively under autoclave oxygen pressure with very little loss of manganese.

Jan 1, 1970

By William W. Adams

A new record in accident prevention was made by the metal-mining a industry of the United States in 1938, as signalized by a lower fatality rate than in any previous year. The rate was less than half as high as in 1911, the earliest year for which figures are available. A good safety record was also established in the prevention of nonfatal injuries, as the injury rate was lower than in any other years except 1931 to 1935, a 5-year period notable for its unusually low injury rates. Employment was more limited in 1938 than in 1937, both in number of men employed and total number of man-hours worked. The number of workdays per man also was smaller than in 1937. Operating companies reported that 7,233 mines were active in 1938 or some part of the year and that the total number of men employed was 103,027. This figure represents the summation of the average number of men employed as reported by the companies, the average for each mine being that for the period during which the mine was active. The number of employees at all mines in 1938 was 15,402 less than in 1937. Reports covering all mines indicated a total of 188 million man-hours worked during the year, or 21 percent less than the nearly 240 million man-hours worked in 1937. In the performance of this work accidents occurred that resulted in the death of 156 employees and the injury of 1.2,722, each injured employee being disabled for more than the remainder of the clay on which he was hurt.. The fatality rate for 1938 was 0.83 per million man-hours worked, which was 9 percent more favorable than the rate of 0.91 for 1937. Nonfatal injuries occurred at the rate of 67.61 per million man-hours worked, an improvement of 10 percent compared with the injury rate of 75.37 for 1937.

Jan 1, 1941

By R. T. Sorensen

Bench-scale and continuous testing were performed to adapt the anionic process for flotation of calcium activated silica to the fine-grained hematitic-goethitic jaspers from the Marquette range, Michigan. These ores typically contain about 35 percent Fe and require grinding to about 80 to 100 percent minus 400 mesh to insure an adequate liberation of gangue from the iron oxides. A method for removal of troublesome slime fractions without excessive iron loss, by first dispersing the quartz and then selectively flocculating the iron oxides, was evolved in the laboratory and successfully accommodated to pilot plant practice. The efficiency of the flotation process was improved with respect to both reagent usage and concentrate grade and recovery by using the selective flocculation-desliming technique as a pretreatment. The benefits of the combined desliming-flotation procedure were most evident in pilot plant processing. The best tests on two ores yielded recoveries of about 84 percent in concentrates containing 65.1 percent Fe and 4.8 percent SiO2 and 66.2 percent Fe and 3.9 percent SiO2, respectively. These results are in comparison to recoveries about 10 percent lower than the above to concentrates containing 63.9 percent Fe and 6.6 percent SiO2 in the one instance, and 63.6 percent Fe and 7.2 percent SiO2 in the other, obtained by flotation without the prior desliming treatment.

Jan 1, 1967

By C. M. Harrer

This paper describes the location, features, qualities, extent, and potential of iron occurrences and some associative resources - limestone and dolomite, coal, petroleum and natural gas, power, and water - in New Mexico. Reconnaissance investigations were made of 118 iron occurrences to determine their extent, attitude, and potential; character samples were analyzed to determine their quality and impurities; and pioneer metallurgical investigations were made on character samples to present their metallurgical problems. Some factors influencing past and potential iron markets are discussed. The most abundant iron minerals are magnetite and hematite, The higher grade deposits are extensive contact-metamorphic and pyrometasomatic replacements in calcareous Paleozoic rocks associated with intrusives. Low-grade deposits of considerable potential are the extensive Cambrian oolitic hematites of sedimentary origin and the Precambrian magnetite-hematite taconite iron formation. Iron occurs also as extensive colluvial and alluvial concentrations. A wide variety of accessory elements are indicated and these pose metallurgical and economic problems.

Jan 1, 1963

By C. M. Harrer

This paper describes the location, features, qualities, extent, and potential of iron occurrences and some associative resources -limestone and dolomite, coal, petroleum and natural gas, power, and water - in New Mexico. Reconnaissance investigations were made of 118 iron occurrences to deter-mine their extent, attitude, and potential; character samples were analyzed to determine their quality and impurities; and pioneer metallurgical investigations were made on character samples to present their metallurgical problems. Some factors influencing past and potential iron markets are discussed. The most abundant iron minerals are magnetite and hematite. The higher grade deposits are extensive contact-metamorphic and pyrometasomatic replacements in calcareous Paleozoic rocks associated with intrusives. Low-grade deposits of considerable potential are the extensive Cambrian oolitic hematites of sedimentary origin and the Precambrian magnetite-hematite taconite iron formation. Iron occurs also as extensive colluvial and alluvial concentrations. A wide variety of accessory elements are indicated and these pose metallurgical and economic problems.

Jan 1, 1963

By Joseph J. Wallace

1. The investigation shows that nine coal beds have been mined in Harlan County, of which the Harlan and Upper Elkhorn No, 3 are the most important from the standpoint of present production. Of less importance are the Hindman, Flag, Haddix, Wax, Fire Clay, Armburgy, and Upper Elkhorn No. 2. The Harlan, Upper Elkhorn No. 3, and Upper Elkhorn No. 2 beds contain the largest remaining known reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 2,138 million short tons as of January I, 1932. Of this total, 1,956 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study, Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1954

By Alton B. Cook, G. B. Shea

"INTRODUCTION In February 1945, Captain (now Commodore) W. G. Greeman, U. S. N., Director, Naval Petroleum and Oil 3hale Reserves, requested the Bureau of Mines to assist the Navy in its wartime development of Naval Petroleum Reserve No. 1, Elk Hills field, Calif., to assure adequate supplies of petroleum products in the Pacific theatre. Unit Operation 4/,engineers desired pressure volume-temperature and viscosity data on the reservoir oil in the shallow oil zone to augment data previously obtained for the purpose of calculating reservoir performance and oil reserves. Accordingly, arrangements were approved by the Operating Committee far, the Bureau of Mines to proceed with a program of field sampling and laboratory determinations designed to obtain the desired information.To carry out the assignment, the Bureau transferred the necessary person¬nel, subsurface pressure, temperature, and sampling instruments, and laboratory equipment for analyzing subsurface oil samples from the Petroleum Experiment Station, Bartlesville, Okla., and the San Francisco, Calif., office and set up a temporary field headquarters in the Elk Hills. The program of work as out-lined by Unit Operation required the 6 months period March-August 1945 to complete during which time individual reports comprising data on pressure-volume-temperature relationships and reservoir oil viscosities as determined on subsurface oil samples and recombined oil and gas samples for 5 selected wells were submitted to Unit Operation.This report is a summary compilation of the data contained in the original reports supplemented by correlations of some of the physical properties of the reservoir oil with the A.P.I. gravities of the produced oil. The report also includes material-balance calculations relative to one of the oil horizons in the shallow zone. The Bureau of Mines believes that publication of the results of these analyses is a worthwhile contribution to the petroleum literature and of particular interest to the California industry."

Apr 1, 1947

By John R. Bartels

Remote operation of continuous mining machines has enhanced the health and safety of underground miners in many respects; however, numerous fatal and non-fatal continuous miner struck-by accidents have occurred. In an effort to prevent these injuries, NIOSH researchers at Pittsburgh Research Laboratory studied the workplace relationships between continuous miner operators and various tramming tasks of the equipment using motion capture data, operator response times, and field of view data to evaluate the factors influencing operator-machine struck-by events (contact with a solid object) in a virtual mine environment. It is not feasible (nor ethical) to use human subjects to directly evaluate factors that precipitate such injuries. However, use of motion analysis data and digital human models can facilitate analysis of struck-by accident risk by allowing investigators to manipulate factors that influence injury. Factors included in this study included machine speed, direction of escape, the direction the operator was facing relative to the machine, work posture, distance from machine, and operator anthropometry. Close proximity to the machine, high machine tramming speeds, a right-facing orientation and operator positioning near the tail all resulted in high risk of being struck.

Jan 1, 2008

By Donald F. Reed

In the latter half of 1948 the Bureau of Mines investigated the Magnet Cove Rutile Co.'s prerty in northern Hot Spring County, Ark. This work was supplemental to the work done by the Bureau on the same property in 1945.2/ It was undertaken for the purpose of investigating the extent of the ore body toward the south and west and at depth and to obtain representative samples of the ore for metallurgical tests. For the latter purpose, the samples were so taken as to minimize alteration of the physical characteristics of the ore, these characteristics being determining factors in working out processes of bencficiation. During the investigation, 27 holes were drilled, 10 with a diamond-coro drill end 17 with churn-drill rigs using a Baker standard cable-tool core barrel. Drilling developed an extension of the ore deposit westward from the previously mined area but did not disclose the full depth of mineralization. Metallurgical tests to determine methods of beneficiating the ore and utilizing the resultant products are now in progress.

Dec 1, 1949

By G. F. Friel

A series of experiments in the U.S. Bureau of Mines Safety Research Coal Mine at the Pittsburgh Research Center evaluated the effects of crosscuts on the travel time of carbon monoxide (CO) along an entry to improve the accuracy of a mine-fire locator program. Three entries, ten single crosscuts, and three double crosscuts were instrumented with CO sensors. One-percent CO in nitrogen was released and monitored as it traveled the entries. In addition to dispersion of CO at the front of the CO wave, CO was entrained from the entry into the crosscuts. It was determined for an entry and single-crosscut configuration that the measured travel time for a concentration change of 5 ppm was 27% greater than the predicted time based upon entry volume only, but 13% less than the predicted time based upon entry and crosscut volumes. For an entry and double-crosscut configuration, the measured travel time for the same concentration change was 25% greater than the predicted time based upon entry volume only, but 10% less than the predicted time based upon entry and crosscut volumes. An effective dispersion coefficient for CO dispersion along one of the entries was estimated to be 1.5 m2/ s.

Jan 1, 2010

By D. L. Paulson

Electric furnace smelting of blister copper directly from copper precipitates (cement copper) was investigated by the Federal Bureau of Mines. Copper concentrations in five different lots of cement copper in the investigation ranged from 62.5 to 82.5 wt-pct. Laboratory-scale smelting tests were made in a 50-kva electric-arc furnace to establish the reductant and flux requirements. Best recoveries were realized by adding 60 pct of the carbon required to combine with the contained oxygen in the cement copper. Operating parameters established during the laboratory-scale smelting tests were used successfully in smelting 20 tons of cement copper during 12 pilot-scale tests in an 800-kva electric-arc furnace. Over 98 pct of the contained copper was recovered as blister-grade metal. The projected energy consumption for a commercial-size furnace was 380 kwhr per ton of cold charge.

Jan 1, 1978

By H. R. Babitzke, H. Kato, M. D. Carver

A number of columbium and tantalum alloys were investigated to determine their suitability for use at elevated temperatures . Columbium-vanadium , tantalum-vanadium , and tantalum-hafnium alloys , and also columbium- 10 wt pct titanium alloys modified with additions of 0.1 to 2 mole pct ZrO2 , TiO2 , ZrB₂ , TiB , ZrC, or TiC were prepared and examined . Workability , tensile properties , and oxidation resistance were tested . Of the columbium alloys studied , the columbium- 12 at . pct vanadium exhibited the best properties ; it compared closely with the columbium- 10 at . pct vanadium alloy studied in a previous investigation.

Jan 1, 1964

By Joseph L. Ritchey

The Trail Lake RARE II area comprises 1,300 acres (526 ha) in Lassen and Plumas Counties, California, adjacent to the Caribou wilderness. No mining claims, prospects, or quarries are reported within the study areas, and no evidence of potential mineral deposits was found during a field reconnaissance. Quaternary basaltic lava flows uniformly underlie the area. INTRODUCTION The Trail Lake (No. B5-095) RARE II further planning area occupies 1,300 acres (526 ha) adjacent to the Caribou Wilderness in Lassen and Plumas Counties, California. Susanville is about 30 mi (50 km) east and Chester is about 17 mi (27 km) south of the study area. Access from State Highways 44 and 36 is provided by well-maintained gravel roads.

Jan 1, 1981