Search Documents

By W. C. Babcock

This report covers Phase V of .a continuing program to apply a new liquid membrane process called coupled transport to the recovery pf metals from hydrometallurgical leach solutions. During this phase of the program, a membrane system of moderate scale was constructed and field-tested at the Exxon Highlands Mine and Mill Co. site near Douglas, Wyoming. The test unit contained four hollow-fiber membrane modules, each with 100 ft2 of membrane area. In the field tests, about 1000 gallons per day of leach solution was processed. The unit was operated on the leach solution for about 50 days. Leach solution entering the unit contained 100 ppm uranium. This concentration was reduced to about 5 ppm by coupled-transport treatment, and the uranium was concentrated to about 2 wt% as a uranyl carbonate product. Under these conditions, a transmembrane uranium flux of about 2.5 lb/ft2-year was obtained. An economic analysis showed that the cost of recovering uranium from this leach solution via coupled trans-port is about $1.20/lb. At higher concentrations of uranium in the leach solution this cost is reduced. For example, at 1000 ppm the cost of uranium recovery is about $0.30/lb.

Jan 1, 1983

By Alfred E. Schwaneke

A new high-temperature soft soldering system has been developed by the Bureau of Mines for use on copper, copper alloys, and low-carbon steel; the method is applicable to automobile radiators and home appliances. The system uses a unique sacrificial metal coating method to promote spontaneous wetting and spreading of zinc and zinc alloy solder: on metallic substrates. The 10-5 to 10-6 cm thick, electroplated or sputtered, sacrificial nickel coating is absorbed by the molten filler alloy during soldering and produces a direct solder-substrate metallic bond. Preliminary measurements on butt joints with copper members give tensile strengths up to 22,000 psi at room temperature using 95 Zn-5 Al alloy as solder. Spontaneous wetting, spreading, and capillary penetration are extremely rapid and produce joints as easily as 50-50 tin-lead solders. Recrystallization or annealing of the wrought copper joint members is negligible at the soldering temperatures of 450° to 490° C and lower. A list of fluxes and solder alloys is included in the report.

Jan 1, 1970

By Robert H. Lambeth

There are no identified mineral resources in the Italian Peak RARE II areas, and there are no producing or developing mines within or adjacent to the study area. Several prospects are in RARE II area M-4945, Idaho, but none were found in the area I-1945, Montana. The Viola Mine (fig. 1, no. 15) vicinity and the Heart Mountain vicinity along the west and south borders, respectively, are being prospected. There has been no recorded production from mines within the study area, but between $2.5 million and $5.0 million worth of lead, silver, and zinc were produced in the adjacent Birch Creek district - dominantly from the Viola Mine - from 1882 to 1889 (Anderson and Wagner, 1944, p. 14). The Viola and other mines in that district are possibly, on basin-margin, carbonate-hosted, lead-silver-zinc deposits stratabound within the Devonian Jefferson Formation. Previous studies have considered them to be hydrothermal, replacement orebodies. Mineral occurrences in the Heart Mountain area are possibly black-shale hosted uranium-vanadium deposits in the Mississippian-Devonian McGowan Creek Formation or perhaps the underlying Devonian Three Forks Formation. The Jefferson and McGowan Creek Formations underlie many scattered segments of the study area. The deposits and occurrence; are not sufficiently exposed to determine tonnage and grade, but sampling indicated moderate resource potential at two properties just outside the study area, the Viola Mine and the Elkhorn Group (fig. 1, no. 33). Local residents indicated there are several thousand tons of zinc-bearing resource; at the Viola line. A 23-ft (70-m) drill hole intercept near Heart Mountain et the Elkhorn Group adjacent to the stuny area contained 0.15 percent uranium oxide

Jan 1, 1983

By Frederick M. Fowkes

Dusts can be filtered out of air streams onto polymer surfaces by electrostatic trapping resulting from the spontaneous transfer of electrons upon contact between dust particles and the polymer surfaces. Such spontaneous contact electrification has been studied quantitatively in this contract with the aid of modern semiconductor charge-sensors with the aim of determining what basic principles govern the sign and magnitude of contact electrification. Information obtained by capacitance-voltage measurements of thin polymer films on silicon showed that charges as large as 4 x 1012 electrons per cm2 develop spontaneously, and that such a charge gives adhesional forces of 165 pounds per square inch (11 atmospheres). Direct measurement of dust polymer contact electrification, using silicon surface channel conductance sensors, also showed spontaneous charges of more than 1012 electrons per cm2. Some polymers can either donate or accept electrons. These included chlorinated polyethylene, chlorinated polypropylene, polyethylmethacrylate, and a copolymer of maleic anhydride with n-octadecylvinylether. Other polymers never accepted electrons but could donate electrons; these included polystyrene, pulychlorostyrune, polyvinylchloride, polyvinylacetate, a polycarbonate (Lexan), and cellulose tributyrate. Contact electrification studies were made with dusts (coal dust, a channel black, or a silica powder) contacting thin films of various polymers solvent-cast onto the semiconductor charge-sensor. Sometimes charging was instantaneous and sometimes slower, but in all but one case (coal dust on a copolymer of maleic anhydride with n-octadecylvinyl ether) the charge trunsfer was a donation of electrons by the polymer to the dust. Some

Jan 1, 1973

By Gary Choate

The work presented in this report represents the background activity which led to the fabrication and testing of a greenhorn and crowd limit switch system for electric shovels. The program began With a literature search and manufacturers product review to gather material as a basis for concept generation. Visits to three open pit mines provided information from operation and maintenance managers which was useful in preparing design concepts. These concepts were evaluated through laboratory tests and engineering analysis to select a final design concept. The resultant greenhorn is four separate shock absorbing pads each enclosed in a housing which bolts to the end of a dipper handle adaptor. The plungers impact against stops mounted to the saddle block. The crowd limit control is a nonmechanical device which senses the location of the dipper and makes appropriate commands to the crowd motor to insure against impacting the greenhorns. The electronic crowd limit control is redundant and indicates malfunction modes. The greenhorn prevents shovel damage in the unlikely event of impact.

Jan 1, 1983

By M. Hertzberg

The Bureau of Mines measured the energy requirements for the spark ig-nition in air of Pittsburgh seam bituminous coal dust, lycopodium spores, and polyethylene powder with a 1.2-L furnace and 8-L and 20-L chambers. Thermal autoignition temperatures of the same dusts were mea-sured in the 1.2-L furnace. Electrical ignition requirements are given in terms of both effective spark gap energies, [ ] and stored circuit energies, 1/2 CE2. The measured order of electrical ignitability for the three dusts is consistent with the data of other researchers; however, the absolute values are systematically higher, probably because of higher flow and turbulence levels in the chambers used and lower electrical efficiency in the circuit used here. The temperature dependence of the lean limit of flammability for lyco-podium was measured wi th the 1.2-L sys tem, and those measurements con--firm the applicability of the modified Burgess-Wheeler law to a dust. Due to experimental complexities, the minimum ignition energies for dusts may not reflect intrinsic flammability behavior. However, some valuable information may be obtained from the relative ignition energies of various dusts at ambient and elevated temperatures. In addition, the concept of minimum electrical ignition energies for homogeneous gas mixtures is reevaluated theoretically.

Jan 1, 1985

By William R. Wayment, David E. Nicholson

A modified percolation - rate test is proposed for use in determining flow rates through hydraulic backfill ; in contrast to the conventional test , a percolation- rate versus void - ratio relationship is established . requirements and a detailed test procedure are described . Equipment Results of a conventional test are compared with those of the proposed modified test . The proposed modified test method yields more accurate , realistic , and usable percolation- rate ( permeability ) data . The significance of obtaining accurate percolation rates for use in analyzing waterflow through hydraulic backfill is discussed .

Jan 1, 1964

By W. D. Kaiser

Recent legislation and expected future legislation is aimed at reducing the dust levels developed in underground coal mines. Several techniques for reducing dust levels are being evaluated. One of these is the modification of cutting parameters such as feed rates, cutting speeds, and pick configurations in order to reduce the amount of dust generated. In order to evaluate the feasibility of modifying cutting parameters to reduce dust, the Bureau of Mines commissioned Battelle to construct a small scale mining machine which could be used for evaluating the effects of those changes in cutting parameters. Specific features of this machine were that it should be highly instrumented to measure various cutting parameters, should have a wide range of feed and speed controls, and it should be possible to vary the pick configurations and geometries on the machine. In addition, it was desired that this machine should have cutting capabilities which greatly exceed present coal mining practice and also that the unit should be small enough and portable enough that it could be taken into and out of operating coal mines with a minimum of interference with the normal coal mine operations. The first step in constructing a machine to meet these requirements was to determine the cutting forces and approximate sizes of components which would be required to cut at the speeds and feeds specified by the Bureau of Mines. Initial calculations using; published data on cutting forces indicated that cutting forces in the neighborhood of 5,000 lbs and power levels of approximately 30 horsepower would be adequate for the application. However, further data developed during the course of the project indicated that when low efficiency picks are used, cutting forces and powers can be two to three times as high as these initially estimated values. After several design iterations, a design was chosen in which the cutting head was driven by four hydraulic motors which were part of a hydrostatic transmission which, in turn,

Jan 1, 1973

By J. P. Powell

The increased costs of exploration and drilling of new oil fields and the continued success of water flooding in nearly depleted oil fields have created a demand for information on the results obtained from individual projects. The Bureau of Mines has published several reports concerning water-flood activity in the Mid continent area and at the request of the industry has continued to collect and disseminate this information. This report was written in response to these requests. It describes in detail the water-flooding projects in Anderson, Franklin, Linn, and Miami Counties, Kans., and includes methods of water treating and the results obtained. The production histories of each county and many water-flood projects are shown graphically from the date of the first development. Maps of most of the major projects, showing their status as of January 1, 1953 are presented also. The practice of injecting water to stimulate oil production was legalized in Kansas in 1935, and the first water-flooding project authorized in this four-county area was initiated by the Texas Co. in December 1935 in Linn County, Forty-nine projects2/ initiated in the area to January 1953 are estimated to have recovered approximately 10 million barrels of oil that could not have been produced by methods used previously. About 7,900 productive acres had been, or are, flooded by these projects, and approximately 1.36 million barrels of water had been injected.

Jan 1, 1953

By H. Kato, G. Asai, R. Blickensderfer, R. Siemens

Some relationships were established among crystallographic orientation , rollability , deformation texture , annealing behavior , slip planes , and ductile- brittle bend transition temperature of molybdenum single crystals . Six large molybdenum single crystals obtained from an ingot melted by electron beam were oriented by X - ray diffraction and rolled on crystallographic planes of low indices in a known direction . During room temperature rolling , cleavage occurred on 100 type planes . At 300 ° C the crystals were rolled to 95- percent reduction in thickness . The crystals ( 001 ) [ 110 ] and ( 011 ) [ 100 ] were most easily rolled . Pole figures were used to correlate the deformation textures of the rolled crystals with the initial crystallographic orientation . Several of the textures which developed could be explained as a rotation about a < 110 > axis of symmetry . The cube crystal ( 001 ) [ 100 ] retained much of its " cubic " orientation . The (001 ) [ 110 ] crystal developed the simplest texture , whereas the ( 211 ) [ 113 ] and ( 211 ) [ 120 ] crystals developed the most complex textures . The 1 - hour recrystallization temperature of the crystal ( 211 ) [ 113 ] was 700 ° C , which is about 300 ° C lower than that of commercial polycrystalline molybdenum . The poles of the slip planes ( as determined from gross slip lines at relatively low magnification ) tended to lie within 20 to 60 degrees of the pole of the rolling plane . The Knoop hardness was slightly dependent upon crystallographic orientation but more dependent upon rolling direction . The ductile- brittle bend transition temperature was dependent upon the rolling orientation and the dislocation density .

Jan 1, 1964

By Chas. F. Jackson

The annual reports of the supervising engineers of the seven sections comprising the Mining Division are assembled in the following pages and constitute the annual report of the division. In planning activities, the aim has been to adapt the work to changing conditions and needs of the mining industries and to avoid becoming bound to any particular type of investigation when others are found to be of more pressing interest.

Jan 1, 1939

By Z. T. Bieniawski, R. K. Zipf

"Zipf Jr., R.K. and Bieniawski; Z.T., 1989. A fundamental study of respirable dust generation in coal. Min. Sci. Technol., 9: 87-99Black lung disease in coal miners induced by the formation of fine fragments of coal imposes very high human and direct costs. A fundamental understanding of the fracture processes leading to fine-fragment formation in coal by applying principles of fracture mechanics is presented. A four-step hypothesis is proposed which sequentially describes the mechanics of fine-fragment formation during a generic coal material—coal cutting tool interaction. These steps include: (1) development of a crush zone under the tool tip, (2) macrocrack propagation. (3) shear movement along macrocracks, and (4) additional fragmentation from shear. This model contains two sources of fine fragments, namely crushing under the tool tip and shearing along the macrocrack surfaces. Three critical assumptions are made that require experimentation. First, the coal material must contain flaws of sufficient density and sufficiently small size to liberate fine fragments by crushing. The following conceptual relationships are proposed between flaw size, spacing and fragmentation: first, the active flaw size must be less than the desired particle size and second, the spacing (or density) must be in the order of the particle size. The second major assumption is that a mixed mode fracture theory will describe the initiation and crack growth direction for the microscopic inherent flaws. The third assumption is that some degree of roughness damage, and interlocking exist along the newly formed macrocrack surfaces such that a small amount of shear movement along that surface leads to additional particle formation at a microscopic scale. Preliminary analysis of the mechanical regime under a cutting tool tip places order of magnitude bounds on the stresses strains, cycle time, stress rates and strain rates. Even though the tool moves and loads the coal material with considerable speed, a quasi-static stress analysis is applicable in this region.Introduction.The generation of fine fragments (respirable dust) during various coal mining processes may lead to the incidence of coal workers pneumoconiosis (black lung disease). The human and direct cost of dust-induced illnesses in coal miners is very large. By several. accounts [1,2] the Federal Government paid out about $12 billion to almost 500,000 coal miners and their beneficiaries between 1970 and 1980. In addition, several states and many coal operators have established their own compensation programs at costs ranging from a few cents to several dollars per ton of coal mined [2]. Since 1980, 'the present liability of the Federal disability trust fund has approached $20 billion and the benefit payments exceed $1 billion per year. There .are also hidden costs due to dust, in the form of increased equipment wear and decreased operator productivity, both of which are due to the poor operating environment. Quantifying these costs may be difficult; however, they may be in the same range as the present pneumoconiosis costs. These high human and direct dollar costs may be prevented or reduced through long term research efforts directed at understanding the generation and control of respirable dust and the incidence of black lung disease."

Jan 1, 1989

This section presents highlights of world economic and mineral industry performance in 1982, a year characterized by continued recession, and selected 1983 forecasts of economic indicators of importance to the mineral industry, some of which indicate a modest improvement in the economies of the United States and Western Europe. The U.S. Economy in 1982 In 1982 U.S. gross national product (GNP) in current dollars increased at a rate of 4 percent, but GNP adjusted for inflation (real GNP) declined at a rate of 1.8 percent. Yearend 1982 real GNP was at roughly the same level as in 1980 (table 1). Thus no growth in real terms had taken place in the United States during the 1980-82 period.

Jan 1, 1983

By W. A. Grosh

Records show that much of the lead produced in the Upper Mississippi Valley lead-zinc field was taken from natural openings along crevice systems at shallow horizons or at the surface. During the early history of the district, the shallow deposits were worked intensively; but in recent years the production of lead, except as a byproduct of deeper mining for zinc ores, has not been significant. Considering the methods of early mining, the character of mineralization, and the fact that galena can still be found on the surface of the old digging areas, it was reasoned that enough mineralization might remain on and above bedrock to permit, through the use of modern equipment and methods, economical re-treatment of surface material in the digging areas.

Jan 1, 1960

The annual reports of the supervising engineers of the seven sections comprising the Mining Division are assembled in the following pages and constitute the annual report of the division. In planning activities, the aim has been to adapt the work to changing conditions and needs of the mining industries and to avoid becoming bound to any particular type of investigation when others are found to be of more pressing interest.

Jan 1, 1939

Continuously monitor and record respirable dust levels underground by a reliable, sensitive, and fast-response device. Approach A light-scattering photometer, having a LED (Light Emitting Diode) light source and other significant improvements, has been designed and incorporated into a portable continuous monitor. How It Works The monitor continuously draws air into the sampling inlet through a cyclone that removes dust particles larger than respirable size. The dusty air enters the photometer vertically downward through a cylinder which is intersected by the optical system. (This cylinder appears as a circle in the drawing of the photometer.) The center of he column of dusty air intersects a beam of pulsing light from the LED, causing some of the light to be reflected, scattered, and refracted. Only the light that is scattered at an angle of about 700 from the light beam passes through a lens to the photodetector which generates an output voltage Signal proportional to the dust content in the air. This signal is detected, amplified, and converted to a digital readout directly in milligrams of dust per

Jan 1, 1979

By J. W. Adams

Two different techniques were wed to make measurements of the absolute value of electromagnetic noise in an operating hardrock mine, Grace Mine, located near Morgantown, Pennsylvania. Diesel-powered haulage equipment is used in this mine, and the electromagnetic noise environment it creates was measured to see how it differs from the environment created by electric-powered haulage equipment. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. Data are recorded using broadband analog magnetic tape and are later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific measured results are given in a number of spectral plots and in amplitude probability distribution plots.

Jan 1, 1974

Geological discontinues in the coalbed, such as faults, sandstone channels, permeability facies, lithotype changes, and large scale partings in the coal seam, can cause intermittent production problems or produce unexpected amounts of water or gas from degasification boreholes. These discontinuities not only can impact methane emissions into the mine workings, especially if they hinder proper and effective degasification of the coalbed but may act as conduits for methane flow from gassy strata into advancing mine workings. The effects of these discontinuities are still under debate by mining and gas production experts. This study presents a numerical investigation using reservoir simulations of the effects of partings and permeability facies and lithotype changes on the production performances of vertical and horizontal degasification boreholes, as well as the emissions during longwall operations. In this work, the grid block was designed in a multi-layer 3-D structure which enabled spatial descriptions of the geometries and properties of the discontinuities within the coal seam. The studied coal seam discontinuities and their properties were distributed arbitrarily within the model. Production was simulated by vertical and horizontal boreholes. Degasification boreholes operated two years prior to start of the mining. The results of this numerical study show that in coal seams with major heterogeneities and discontinuties, the geometry and location of the boreholes are important for improved gas production. These considerations are also important for controlling methane and water inflow into the working environment during longwall mining.

Jan 1, 2008

By F. X. Tartaron

Behavior of hard-burned quicklime was compared with that of soft-burned quicklime in an oxygen converter utilizing oxygen blowing in a rotating cylindrical vessel, set at a 30° to 60° angle to the horizontal and operated at a predetermined speed of rotation. Four pairs of tests were made) each comparing hard lime with soft lime. Three of the pairs differed from one another in the quantity of lime employed) and the fourth differed in blowing time, All four pairs showed an increase in yield when soft lime was used. Three of the pairs revealed that the ratio of the oxygen consumed with soft lime to the oxygen consumed with hard lime was the same as the ratio of metal yield with soft lime to the metal yield with hard lime. The fourth pair contained an error and could not be included. Finally, a close inverse relation was found between the combined iron in the slag and the combined lime in the slag, which can be expressed by the equation pct Fe = 52.67 -0,906 (pct CaO).

Jan 1, 1967

By K. E. Tame

Pollution from radioactive nuclides, principally Ra226, in liquid waste from uranium mills can be minimized by reusing the waste solution within the mill. Such reuse of waste solution in the Vitro Chemical Co.-type process was investigated in the laboratory. Vitro employs an acid leaching process for dissolution of the uranium, countercurrent decantation for liquid-solid separation and washing, and amine solvent extraction for recovery of the uranium from solution. The simulated reuse of barren raffinate in the mill circuit was carried through two separate laboratory campaigns of 29 and 31 cycles. Conventional chloride stripping of the amine was employed in the first campaign, whereas nitrate stripping was used in the second campaign. Dissolution of uranium from the are in the acid leaching circuit averaged 96 percent. Washing efficiencies of 98 to 99 percent were attained by using 4 volume tons of combined raffinate and makeup water per ton of ore. Uranium recovery from the pregnant solution using a 5-percent solution of amine LA-1 in kerosine ranged from 99.3 to 99.9 percent.

Jan 1, 1962