Search Documents

By G. Hames, A. Drake, B. Sampson

The Timbarra opencut gold mine is located about 30 km(19 miles) southeast of Tenterfield in northern NSW some 4 hours by car from Brisbane, the capital city of Queensland in Australia. It was a small operation designed to produce about 40000 ounces of gold per annum utilising contract mining and company owned crushing plant feeding heap leach pads. This is a standard setup except that the mine owner was in charge of all aspects of drill & blast design even though a contract drilling & blasting (shotfiring) service was being provided. The major problem was that the blasting operations were yielding massive amounts of oversize due to the jointed partially weathered nature of the granite. This was adversely affecting all downstream aspects of the operation as well reducing gold output as ore boulders were being dozed over the side of the mine as they were impinging on mining productivity. The oversize problem had to be solved as the mine was struggling to achieve design gold output. Significant design & trialing effort using minesite resources were utilised to reduce the oversize but this failed even when powder factors up to 1kg/bcm(1.68lb/yd) were used. Dyno Consult from Dyno Nobel were therefore called to investigate, review & trial options to reduce oversize from the top flitch.

Jan 1, 2003

"Rock falls involving a relatively small amount of material are a leading cause ofinjuries in underground mines in the United States. A contributing factor is unwantedblast damage and over-break. A goal of the United States National Institute forOccupational Safety and Health is to reduce the number of ground fall-related accidents by improving drift driving practices through the introduction of perimeter control blast designs. This paper presents a blast design technique based on a hydrodynamic method. Using commonly available explosive and geometry data, the theoretical particle velocity is calculated as a function of distance away from a cylindrical charge. A calibration factor is introduced to account for actual conditions by comparing the predicted values to a set of field data. The calibrated curve can then be applied for design. The paper introduces modifications to account for different explosives from those used in a calibration test. The application of the approach is demonstrated with respect to a data set from a large-scale concrete block test."

Jan 1, 2009

By Dale S. Preece

The computer program. DMC Qistinct Motion &de), which w&s developed for simulating the rock motion associated with blasting, has been used to study the intluence of row delay timing On rock mOtiOn. The munerical simulations correspond with field observations in that vmy short delays (< 5Oms) and vety long delays(> 3oOms) produce a lower percent-cast thao a medium delay (100 to ZOO ms). The DMC predicted relatio&lp between row delay timing and percent-cast is more complex than expected with a dip in the auve where the optimum timing might be expected. More study is required to gain a full undasranding of this phenomenoo.

Jan 1, 1994

By Cristian Rodriguez, Tom BoBo, Maria Rocha, John Kemeny

Blast fragmentation depends on many factors. First of all, it depends on the specific blast design, which includes the amount and type of explosive, the blasting pattern, the timing and sequencing, and other parameters. Secondly, it depends on the properties of the rock mass, including the uniaxial compressive strength (UCS), the rock mass elastic modulus (E), the rock discontinuity characteristics (as reflected in the GSI or RMR), and the rock density. Several fragmentation models have been proposed to predict blast fragmentation based on the blast design and the properties of the rock. These models include the Kuz-Ram model and variations of this model, as well as recent models by Kim and Kemeny (2011) and others. Fragmentation models are validated and calibrated by comparing the predicted fragmentation with actual post-blast fragmentation from image processing monitoring systems.

Jan 1, 2014

By David M. Langlais, Krystle Pelham

"Explosives used in blasting operations, natural and anthropogenic sources such as septic systems,fertilizers, and decomposing vegetation can potentially contaminate groundwater with nitrate in thevicinity of construction sites and make identification of blasting impacts difficult. Blasting operationsfor a private construction project in Windham, New Hampshire were indicated as the source of water quality impacts to private drinking water wells prompting the New Hampshire Department ofTransportation (NHDOT) to implement a proactive approach to limit the potential for impacts fromblasting for ongoing NHDOT projects. NHDOT has developed a baseline drinking water monitoringprogram designed to detect potential impacts and to ensure alternative drinking water is providedthroughout the construction phase of projects. In 2013, the U.S. Geological Survey (USGS) andNHDOT began a study to determine the source and fate of nitrogen compounds near blasting sites using a combination of isotopic, time series, geochemical, hydrologic, and geologic data. Approximately 1.75 million cubic yards (1.33 cubic meters) of rock were removed by blasting in several locations for roadway construction at a major highway construction site in southern New Hampshire."

Jan 1, 2016

By Bruce Vandenberg

A 3D, PC based computer program is currently under development by Blasting Analysis International, Inc., to analyze the kinetics of full scale blasts with two or more high-speed motion picture cameras.

Jan 1, 1990

By Wawa Jaka Sungkawa, Slamet Rachman Jaka, Tom Dermody

Nowadays, with such a focus on environmental protection, surface mining activities have come under pressure to ensure their activities do not adversely affect the local surroundings. As part of the extractive process, blasting activities are an integral part of a mining company’s operational cycle. Consequently achieving beneficial blast results while complying with environmental requirements has become a key focus. This especially is the case when firing blasts within close proximity of residents where additional control measures need to be implemented to control vibration. One case where this occurs in Indonesia is in the Paringin Pit, one of the operational areas of the company's. The pit has complex geological conditions and is surrounded by several residential areas. Between 2014 to 2017 there were 12 cases of ground vibration exceedance due to blasting. As part of a continuous improvement project the company's targeted minimizing the vibration exceedance in this area. A project was undertaken to research and develop a method to confidently predict vibration. It was decided that the scaled distance formulas were not adequate to predict vibration when using non-electric detonators, as accurate wave propagation could not be achieved. The problem is how to manage of complex geology condition related with wave propagation in ground vibration control. Geological condition mapping with specific spatial range can and combine with Signature Hole Analysis be a solution to make wave propagation easier to accommodate in ground vibration control. With this new approach geological condition mapping with specific spatial range was produced that would minimize vibration while ensuring beneficial blast results. Introducing the new prediction produced nil cases of vibration exceedance in 2018 and beyond and proved that the Signature Hole Analysis in specific spatial range of geological condition is the preferred method to optimize blast result and maintain vibration control.

By Pat McLaughlin

Blast design in the construction industry has often been based on past practice or powder factors. This is to some extent understandable, since construction projects do not have the longevity of mining or quarrying operations and therefore have less opportunity to pursue potential improvements. The main concern of the operator is whether or not the technique will work, and at what cost to the downstream processes. Time, not long term savings, is of the essence.

Jan 1, 1994

By R. Raghavaraju

Estimation of the dynamic stress field in terms of its amplitude and decay around a blast hole is a key input parameter in all numerical modeling and blast prediction exercises. However, there is very limited information available in literature on these critical parameters, which would be considered essential in any blast modeling exercise. A laboratory-scale experimental study has been carried out in two different rock types to study at very close range the stress wave decay from a blast hole at distances ranging from 3 to 10 borehole radii. The single–hole blasting experiments employed a centrally located detonating cord (5.3 g/m) in 6 mm(1/4 inch) and 10 mm (3/8 inch) boreholes. The coupling medium employed was air and water, in addition to using a thin-walled copper tube in intimate contact with borehole wall to prevent of penetration of explosion gases into the emerging cracks. The paper describes the nature (amplitude and decay) of the transmitted shock pressure and their evolution in the two rock types for these various experimental conditions, which are present to varying degrees in all blasting operations.

Jan 1, 2014

By Mike Cammack, Logan Huppert, Gustavo Azpilcueta

During the summer of 2015, Unisea Inc. sought proposals for the G1 Dock Replacement Project in Dutch Harbor, Alaska. It would be a one year project and construction was scheduled to begin in the spring of 2016. One aspect of the project was the requirement for a layer of armor stone to protect part of the dock. An estimated 30,500 tonnes (37,670 t) of armor stone were needed for the project. The source of rock was the Unisea Quarry due to its proximity to the project and the quality of the stone meeting all the required technical standards.

Jan 1, 2018

By Hairong Zeng, Matthew Baumann, Shahram Tafazoli, Edmond Chow

Measurement of rock fragmentation has evolved from a completely subjective and manual process to a statistically objective and semi-automated process. However, ultimately, the vision is to achieve a statistically representative and fully-automated process. From the blast optimization perspective, it is critical to receive reliable rock fragmentation results quickly to incorporate into the planning of subsequent blasts. Since manual rock fragmentation measurement methods tend to be time consuming, a fully-automated method is the practical way to meet these requirements.

Jan 1, 2012

By SMF Hossaini

With the aim of a clearer understanding of the applicability of existing empirical equations for blast induced ground vibration, an investigation has been conducted on three mostly applied forms of such equations. The effect of explosive type on the applicability of these equations has been assessed by analysing 44 sets of data produced by using two types of explosives, namely ANFO and slurry explosive, in an open pit coal mine. The analysis of the data has revealed that the type of explosive affects the applicability of the criteria of the three equations. All three criteria have better correlation with the data of shots in which ANFO was used than the shots with slurry explosive. However, the applicability of one of the criteria is reduced, by far, only by replacing ANFO with slurry explosive for the same ground conditions. It was also found that one of the parameters of these criteria (i.e. “k”) is significantly sensitive to the type of explosive in all the three equations. The degree of influence to the values of “k” obtained by the variation of explosive from ANFO to slurry explosive in the three equations is 76.3%, 811% and 39%. This implies that “k” is not only dependant on ground conditions, as stated in most previous publications, but is also strongly a function of the type of explosive.

Jan 1, 2004

By Frederick B. Kuhnow

Harmonic energetic delamination of T2 building is being considered for demolition at a formerly known atomic lab. The T2 building is within a containment structure that is under a negative pressure of -49 Pa (-0.2 inches of WC) so that no remaining radioactive material is leaked out. The T2 containment enclosure is a portal frame-type system that spans east/west over 35.05 m (114’-11 7/8”) and spaced 2.9 m (9’-6”) apart. The west side of the portal frames is supported by a 64 cm (2’-1”)thick concrete wall which is backfilled to the west and open to the T2 basement to the east. The east side of the portal frames is supported by a 61 cm (2’-0”) thick concrete wall that is backfilled to the east and open to the tank farm vaults to the west. A concrete slab-type footing supports both the east and west walls. Transverse walls provide lateral support for the walls as part of the original design. The west wall has an elevated slab that provides further stiffening of the concrete wall between the transverse walls.

Jan 1, 2017

By John Babcock, Bryan C. Smith

In a partnership between Luck Stone Corporation and Loudoun Water, a 42” (1.067m) steel pipeline was constructed along the perimeter of an extensive permitted reserve of diabase rock Luck Stone was about to begin mining. Loudoun Water provides drinking water and wastewater services to over 75,000 households in Loudoun County, Virginia. In discussions to establish the 30-foot (9.1 meter) easement for Loudoun Water within the permitted reserve of diabase rock, Luck Stone and Loudoun Water agreed on the following basic conditions: • Luck Stone could execute production blasting as close to the easement as physical conditions of overburden depth permits. We estimated the minimum distance to be about 75-feet (22.86 meters) from the centerline of the pipe. • Loudoun Water would install strain gauges on the pipe every 500-feet (152.4 m) along the entire length of the future reserve area. This resulted in the installation of 18 strain gauges. • Luck Stone would contract a third-party vibration monitoring company, agreed to by Loudoun Water, to monitor the strain gauges and provide seismograph reading at appropriate locations along the pipe as mining progresses. All information would be provided to Loudoun Water. • Luck Stone’s blasting will be conducted in a manner that ensures the recommended strains are not exceeded.

Jan 1, 2019

By D. Fry, S. Hunsaker

Ammonium nitrate in explosives and sulfides in reactive ground have the potential to react at ambient and elevated temperatures resulting in premature detonations. The Australasian Explosives Industry Safety Group (AEISG) published, in 2006, a Code of Practice1 for elevated temperature and reactive ground. This paper reviews the chemistry, general reactivity of various ground types, elevated temperature hazards, and testing protocols contained in the code, that are industry best practices for managing ammonium nitrate-based explosives in elevated temperature and reactive ground conditions. In addition to reviewing the 5th edition AEISG Code of Practice, data is presented validating the recommended sampling guidelines within the code. Dyno Nobel has been screening reactive ground samples and performing sleep time testing since the code of practice was first released. Test results demonstrate the effects of samples that are allowed to oxidize before testing and are shown to be subsequently less reactive and not representative of the actual hazards facing mining blasting operations. Results also show that for a given reactive ground sample, reaction times decrease with increasing temperature. Data also quantify the delay in reaction time given by inhibited products. These results emphasize the importance of proper sampling and preparation of samples to accurately characterize elevated temperature and reactive ground hazards. They also demonstrate the efficacy of inhibited products in managing these hazards

Jan 1, 2024

By Douglas Rudenko

Most engineers, mine operators, or contractors acknowledge the importance of having accurate subsurface information in order to plan a project or solve a problem. Conventional methods of exploring the subsurface such as augering, core borings, or test pits can provide information, but it is often costly and sparse. Geophysical methods offer an alternative to help supplement sparse information~ gathered through conventional exploration techniques.

Jan 1, 1998

By Francisco Sena Leite, Raquel Sobral, Vinicius Gouveia de Miranda, Céu Jesus

"The urgent need for improvements in the control and mitigation of environmental and social conditions associated with the extraction and processing of raw materials is increasingly a demand imposed by legal entities and institutions. Therefore, this present article proposes an improvement of the estimation in the magnitude of the vibrations resulting from rock blasting methodologies in the surrounding areas,incorporating the heterogeneity caused by uncontrollable parameters, such as geological andgeotechnical characteristics. This methodology combines the use of empirical vibration attenuation lawscommonly known and with terrain discretization techniques using Voronoi’s decomposition. For thevalidation assessment of this methodology, the data set collected and compiled is composed by 87 vibration measures collected in 16 sample points in one area of study of which 2/3 of the samples were used to create the model and 1/3 for the validation. Using normality tests for statistical residue analysis,it is possible to infer that this present model has null residual mean, as well as a smaller sum of residualerrors. Comparing the methodology present in this paper with the procedures executed nowadays, areduction of the errors associated with the estimation is obvious, highlighting a better characterization of the behavior of the vibrations associated with rock blasting."

Jan 1, 2017

By Joseph A. Meyers

NYC has always been a high-profile target for both foreign and domestic terrorists. Explosives have always been the go-to tool for terrorists to bring about serious physical injury, death, and property damage in our society. Today with the anti-police movement gaining traction in the United States and anarchists groups using homemade explosives against law enforcement and municipalities, it is the responsibility of the explosives industry to ensure that every explosive product on a blasting site is secure. We must prevent the theft of these energetic materials used on projects and sold by vendors so they are not used by these terrorists. We have learned many lessons here in NYC which began with the theft of explosives used for blasting projects in NYC to supply the IRA (Irish Republican Army) 50 years ago. The liability is too significant to take short cuts in securing energetic materials. Over the years through cooperation with all agencies and the industry we in NYC have developed certain proven protocol and procedures we would like to share with the industry. An efficient and effective security plan for the logistic movement of explosives, as well as for the blast site is imperative to keeping the good name of the industry from negative repercussions and possible additional bureaucratic oversight of an industry that is highly regulated and still recovering from the pandemic. Communication, security assessments and transparency with all stakeholders and the Authority Having Jurisdiction (AHJ) will greatly improve the overall security for the blasting project. This SOP (standard operating procedure) will allow the AHJ to become a proactive partner in the security of the blasting project. If the AHJ is not a law enforcement agency, the law enforcement agency specialty unit must be notified and included in all phases of the project. The security for a blasting project with AHJ and law enforcement input starts at the inception of the project when the memorandum of understanding (MOU) is obtained, and involves the AHJ through all steps of the approval process. This includes threat assessments on new and existing structures. SME’s (Subject Matter Experts) must be present at all stages. The blasting industry and regulators must work collaboratively to improve safety, security, and create a dialogue with law enforcement and the AHJ. Relationships are built through trust, teamwork, transparency, and communication and greatly improve the safety of our great country.

Jan 21, 2025

By Robert Hopler

As a part of the depression and rectification work on the Port Morris branch of the Harlem Division of the New York Central & Hudson River Railroad, a short tunnel is being driven under St. Mary’s Park. The park is near 149th St. and St. Ann’s Ave., in the Borough of the Bronx, New York City.

Jan 1, 2006

By Michael S. Wieland

"Toxic fumes cause fatal andnonfatal incidents in underground mining, where the working environment tends to trap the fumes, hindering the restoration of non-harmful conditions. Workers can underestimate the residual fume toxicity and return to the work site too quickly. The toxic fumes from charge explosions depend upon a number things: formulation ingredients, mixture uniformity, water resistance, hole contaminates, rock hardness, and dust interactions. Transitory hole-to-hole waves can cause partial desensitization, ruin the reaction kinetics, and worsen the fume toxicity.Traditionally the toxic fume hazard for a candidate explosive is resolved from a requisite tally of fume components. The resolution starts with the fume spectrum, a tabulation of specie concentrations, transformed to standard reference conditions and readjusted to remove the air dilution. The resultant influence, which is referred to as relative fume toxicity RFT, is deduced by a formula rule with some chosen constants and the requisite concentrations. The RFT result is normally compared to an RFT criterion that represents the worst-case (maximum) tolerable fume toxicity, as stipulated by regulations or otherwise."

Jan 1, 1997