Search Documents

By Peter N. Calder, John N. Tuomi

The development of a successful control blasting program for an open pit iron mine in hard jointed rock is described. The objectives and mechanics of control blasting are discussed. Design and implementation procedures, which should have wide application, are given. Small diameter angle hole pre-split blasting, buffer blasting with production holes in front of pre-split lines and in front of strongly defined rock structures, and vibration control of production blasts are dealt with.

Jan 1, 1980

By Kahmmelly Mathildes Pimenta Coelho, Felipe Dantas, Jaine Ribeiro de Souza, Augusto Ferraz, Carlos Roberto Campos Junior, Davi Bastos Martins de Oliveira

The Carajás Iron Mine, recognized as the largest iron ore province in the world, is notable for its continuous efforts to improve operational efficiency and safety. In response to these objectives, a QA/QC (Quality Assurance and Quality Control) Program was implemented and integrated with Blastscout Probe technology to optimize drilling and blasting processes. The program supports the standardization of operational parameters, the execution of regular audits, and real-time data analysis, facilitating precise and timely adjustments. The implementation led to significant improvements, including an 80% increase in operational compliance, a 49% reduction in drilling depth deviations, and a 30% enhancement in Jaspelite fragmentation. This study presents the methodology employed, the outcomes obtained, and the positive impacts observed in both operational performance and environmental management.

Jan 26, 2026

This paper presents a brief discussion of three case histories to illustrate several aspects of the question of blasting in or immediately adjacent to concrete. The results demonstrate a need to make dramatic upward revisions in previous criteria, whether it be the standard particle velocity criteria or damage response spectra bounds, - especially those which include conservative upper limits of constant acceleration for the high-frequency portion of the spectrum. It is demonstrated, also, that conventional off-the-shelf blast-monitoring instruments are not capable of monitoring small blasts at close range. Both the frequencies and the levels of effect are beyond the range of such instruments. These case histories suggest further that there is a need to review the applicability of certain wellknown equations of elasticity.

Jan 1, 1980

By Catherine T. Aimone-Martin, Susan G. Beattie

A series of small scale explosive tests were performed at a perlite mine near Socorro, New Mexico. The tests were designed to investigate the azimuthal or directional relationship between small scale geologic structures such as joints and the propagation of explosively-induced ground motions. Three shots were initiated within a single borehole located at ground zero at depths varying from 83 m (272 ft) to 10 m (32 ft). An array of three component velocity and acceleration transducers were placed in two concentric rings at distances of 20 m (66 ft) and 40 m (131 ft) surrounding the single hole at 7.5° , 15° , and 30° azimuths as measured from ground zero. Data from the transducers were then used to determine the average propagation velocity and waveform characteristics of the blast vibration through the rock mass at the various azimuths. The rock mass was mapped to determine the predominate joint orientations (strike and dip) and the average propagation velocities were correlated with this geologic information. The results showed that there is a correlation between the predominate joint orientation and ground motion amplitudes and velocity. The more predominate geologic structures allow the wave to follow along their strike thereby forming a planar path of least resistance and in turn, allowing higher velocities and amplitudes. Secondary joints or structures may act in concert with more prominent features to form a network of channels or paths along which the wave moves more freely than it may when traveling against the structures. The greatest azimuthal variations in velocity and amplitude was observed for the shallow shot at 10 m (32 ft) depth.

Jan 1, 1996

By M Oldenburg, P J. Digby, L Nilsson

A constitutive model for the simulation of fracture and fragmentation processes in rapidly loaded rocks is studied. The model was included in a wave propagation finite element code. The results obtained from two different configurations of explosive charge and reflecting surfaces in a plane strain problem were studied. The evolution of the time-dependent fracture pattern is presented.

Jan 1, 1985

By Charles H. Dowding

Public concern over blast-induced CRACKING has led to the search for a radically new approach to vibration control. The present system, while scientifically correct, is cumbersome to explain. Historically the potential for blast-induced cracking has come to be described through velocity time histories, which are correlated with observation of crack extension under controlled experimental conditions. Unfortunately time histories are simply too difficult for jurors and village or county regulatory boards to understand. Furthermore these arbiters must accept on faith that the observers were unbiased. Since these public bodies control the manner in which blasting activity is adjudicated and regulated, information must be presented in a form they can understand and that is not subject to second-guessing.

Jan 1, 1999

By Zhao Jie, Christopher G. Smith

Commercial explosive use in China has been dominated by powdered AN-TNT mixes. Water gels and emulsions are now gaining market acceptance because they offer potential for better performance. Although raw material costs for emulsions initially may be more than AN-TNT mixes, the more expensive technology improves sensitization and leads to lower costs overall for mining operations. A recently completed study in northeast China compared microsphere-modified emulsions to AN-TNT and lower-cost emulsions. Testing of microsphere-modified emulsions at several pH levels indicated a high degree of stability and consistency of VOD. Using 42 mm blastholes in underground mines and 170 mm holes in sandstone open pit mining demonstrated the superior performance of glass microsphere sensitized emulsions. Comparisons of explosive cost, drilling cost, secondary blasting cost and muck pile profile were favorable to the microspheres-sensitized-emulsions. Noxious fumes with AN-TNT or with water-based systems that partially fail during detonation are also a concern. Efficient detonation of emulsion products sensitized with hollow spheres appears to reduce fume generation. Prolonged storage or exposure to water also is not a problem.

Jan 1, 1997

By Quian Liu

Since the establishment of the CANMET Experimental Mine in Val d'Or, Quebec in 1991, research activities in rock fragmentation have been carried out not only in the underground laboratory but also in production mines in the north-west Quebec region. Among the instruments available for rock fragmentation, the Kodak EktaPro 1000 Motion Analyzer (also called the high speed video system) has been one of the most useful tools for monitoring blasts in both underground and open pit. This system is capable of recording events at rates from 50 to 12,000 frames per second (fps). The buffer memory has a capacity of storing 2050 images. To use this system in the underground, a steel box was made with a bullet-proof glass in the front to protect the camera. The processing and recording equipment are placed in an aluminum case which can be located about 30 m away from the camera via an extension cable. For each blast monitored, high frequency geophones and accelerometers were used to monitor ground vibrations and give a timing reference of the explosive detonations to correlate with the observation of the captured images.

Jan 1, 1994

By James E. Jr Hargroves

With the ever-increasing population growth and modern trend to urban development, the expansion of utilities is a stable, mad or, and constant source of income for many. Blasting is a "necessary evil" to the utility contractor. It can make or break even the most solvent. Housing development expansion and higher treatment of effluents are causing utilities to appear in more congested areas. This paper discusses some of the aspects of utility blasting in the State of Virginia. Consideration is given to bid procedures, pre-blast surveys, record-keeping and practical application.

Jan 1, 1977

By Jim Hall, Denis Rickman, Jon Windham, John Ehrgott, Stephen Akers, Byron Armstrong

With the growing concerns about terrorism world-wide, numerous agencies conduct experiments to investigate the effects of terrorist vehicle bombs. In many cases, the vehicle bomb of interest utilizes some form of ammonium nitrate/fuel oil (ANFO) as the explosive source. Due to the high cost of fullscale testing, it is advantageous to conduct at least some vehicle bomb experiments at reduced scale. Extensive testing has shown that ANFO is a non-ideal explosive, and its explosive output does not scale reliably at explosive masses below approximately 400 lb (182 kg). Most scale-model testing requires explosive masses 1 to 5 orders of magnitude smaller. Thus, scale-model testing is typically conducted with “ideal” explosives, such as composition C-4, which perform in a scalable manner at virtually any charge mass. The utilization of an ideal explosive to model ANFO requires the existence of an accurate means of equating the performance of the two explosives. The airblast equivalence of C-4 and ANFO has been well established. However, the cratering equivalence of these explosives is not thoroughly quantified. This is especially true for the case of an above-ground detonation, which is precisely the scenario of interest in vehicle bomb studies. A study has been conducted to better define the cratering equivalence of C-4 and ANFO for above-ground detonations. This paper presents a discussion of results from this research.

Jan 1, 2008

By C Jamie Kridler

"An increased concern for pit safety and more stringent, highwall requirements for augermining of final cuts has led to a new emphasis on wall control for a Central Pennsylvaniacoal operator. Over the course of two and one half years and several locations, fieldpersonnel developed a very practical yet very effective system for maintaining safehighwalls. This involved the use of the blast design to: l) shape the highwalls 2) create andprotect a system of benching 3) pre_split large diameter holes using suspended ANFOcharges."

Jan 1, 1993

By James D. Cook, Dan McCutchen

Effective overburden casting requires the efficient use of todays explosives and initiations systems if a mine is to survive. This paper uses a major coal stripping operation as an example of the proper application of explosives and initiation system to their conditions.

Jan 1, 1994

By Tom Hale

Developers and blasters are faced with increasing public demand and regulatory restrictions to maintain the lowest possible levels of noise and vibration from blasting operations in populated urban areas. Pyrotechnic products have proven to be a low noise, low vibration alternative to conventional blasting for close-in rock excavation and concrete demolition applications. Pyrotechnic breaking charges often yield 1/10th the vibration and noise compared to traditional explosives, and have been demonstrated to increase public confidence and decreased damage potential where they have replaced explosives, thus allowing new opportunities for work and greater job profitability. This paper presents a practical approach to utilizing pyrotechnic products in various applications including trenching, mass excavation, demolition, and dimension stone production, providing methodology for pattern design, vibration probability and loading calculations. Field research data is reviewed and compared to conventional explosives.

Jan 1, 2008

By Michael D. McGill, John L. Turner, Don Sieger, Doyle Newhouse

Since its introduction by Atlas Powder Company in late 1986 as a means of highwall stabilization in surface coal mines (1), applications of the basic AirDek (2) blasting technique have multiplied rapidly.

Jan 1, 1991

By Jikai Rong Changai Liu

The dig instrument by blasting is a,new product we developed(See Fig. 1) It is an apparatus to dig hole at the ground. It is composed of combustor A, combustor B, charge pipe and shock head. Work characteristics of Combustor A are that combustion time is 1. 5 seconds, driving force is 725kg. Work characteristics of combustor B are that the combustion time is 1. 3 seconds, driving force is 460kg. After the combustor is ignited, the charge pipe is drived into ground immediately. Then, whole dig instrument is threw out automatically, but explosive in charge pipe is left in ground and blast in the twinkling. The diameter of vertical hole formed by blasting is 3cm to 60cm which is controlled according to engineering requirement. The maximum depth of the hole diged by using the dig instrument is 2M. It applies to blindage of single solidier in military affairs, and hole planting pole as well as sewer in civil use and so on. The two shots are charged in combustors to dig a hole. The maximum weight of shot is 490g, minimum is 130g. The whole process diging hole is completed automatically in about ten seconds.

Jan 1, 1998

By Karl E. Burgher

Accidental explosions occur throughout the world. They can happen at chemical plants, fireworks plants, grain depots, or as a result of collisions involving volatile or hazardous chemicals. It is interesting, as we know as blasters, that we can take two very harmless products and mix them under certain conditions and produce a violent explosion. It is often very difficult for the investigator to determine the magnitudes of blasts after the fact. However, an estimate must be made to settle vibration and airblast damage claims. The blasting consultant or technical representative is often called upon to act as an expert to mitigate these claims.

Jan 1, 1993

By Thomas E. Lobb, Harry C. Verakis

Significant progress has been made in the reduction of serious injuries and fatalities resulting from mine blasting operations. Despite the progress, injuries and fatalities continue to occur. A leading cause of injuries and fatalities from blasting continues to be inadequate blast area security. Even though significant improvements in technology have been made, insuring adequate blast area security remains a challenge and requires constant vigilance. The advances in technology have created safer blasting products and have improved productivity and economics by enabling large, more efficient and effective blasts. However, as blasts grow larger in size, the complexity of adequately securing the blast area increases even more. Periodically the basic fundamentals involved in blasting safety should be reviewed, particularly for securing a blast site regardless of the size of the planned blast. Factors such as flyrock and toxic fumes must be taken into account to insure the safety of persons and property from the results of a blast. This paper examines the factors related to injuries due to inadequate blasting shelters and blast area security, and identifies mitigation techniques. The key concepts are: (a) accurate determination of the bounds of the blast area, (b) clearing employees from the blast area, (c) effective access control, (d) use of adequate blasting shelters, (e) efficient communications, and (f) training. Fundamentals are reviewed with an emphasis on analyzing task elements and identifying root causes for selected blasting accidents. Mitigating techniques are presented along with discussions and examples.

Jan 1, 2005

By D G. Dressler, Paul Yeager

A previously little-known facet of seismic frequency spectrum analysis is gaining significance. The frequency spectrum of seismic waves promulgated from blasting is a significant factor in causing blasting complaints and threshold (architectural type) damages.

Jan 1, 1987

By Stanley J. Vitton

An important factor to consider during blast damage investigations is whether the structure was constructed on collapsible soils. Traditionally, these soils have been considered to be soils such as loess deposits, which occur along the Mississippi River in locations such as Vicksburg, MS. However, recent research into collapsible soils has indicated that a number of soils may also fall into this category. A collapsible soil is any soil that is susceptible to large decreases in bulk volume upon saturation.

Jan 1, 1997

By Corry Goumans

Photos 1 - 4 – Chris Elliott is a rock slope supervisor on a construction project east of Seattle, Washington. His job is to look after a “two man” scaling crew working on the rock bluffs some 300 feet in height along the I-90 interstate just east of the town Hyak. The Washington State Rock Engineers noticed a very large mass of unstable rock along the upper rock face and asked us to take it out. Chris is loading explosives in 1½" ” holes that are 8 to 10 feet deep by 40 feet long with 1¼” x 8” power primer on the unstable rock mass that is about 300 feet above the new road construction. I-90 runs east and west longside the new construction note the containment fence and the ship containers along the highway for protection and Lake Keechelus in the background.

Jan 1, 2014