Search Documents

By Joshua Hoffman, Catherine Johnson, Braden Lusk

Blasting conducted in surface coal mining operations in the Appalachian region consumes a significant amount of blasting agents. Emission of oxides of nitrogen (NOx) from these operations potentially represents an environmental challenge. This paper presents work conducted to quantify NOx output from the detonation of blasting agents common to surface blasting operations in surface coal mines. Annual ANFO and emulsion consumption data was collected from an operational surface coal mine located in West Virginia. It is known that many factors contribute to the types of gaseous byproducts released from the detonation of explosives. These factors include but are not limited to: fuel to oxygenator ratio, degree of confinement, and contamination. While, past research has been conducted to study the relationships these factors play on the release of NOx, these findings do not agree with one another. The annual explosive consumption values from the West Virginian mine were applied to NOx emission conversion factors in published literature. This lead to a range of NOx emissions from 95 to 914 tons in a year. Given the wide range of NOx production the utility of this information is suspect. The EPA recognizes a standard factor of 17 lbs (NOx)/ton (ANFO) however this factor is based on chemical composition and does not address contamination, confinement, or AN to FO ratio. This factor when applied to the West Virginia Mine's explosive consumption produced a value of 215 tons of NOx. There is a lack of information on NOx emission from emulsion type explosives. The work presented in this paper can be used by blasting professionals to quantify NOx emissions and guide future work for producing better predictor factors.

Jan 1, 2014

By S. Behera, K. Dey

This paper presents a methodology for finite element (FE) modelling to analyse the total deformation of rockmass under blast-load, with a focus on predicting backbreak that may occur during surface blasting operations. Backbreak can result from improper use of explosive energy, leading to damage beyond the excavation zone and jeopardizing operational safety and productivity. The paper highlights the impacts of backbreak on bench stability, excavator operation, drilling operation, flyrock generation, and improper fragmentation and boulder formation in surface blasting. However, prior estimation of extent of rock breakage zone can provide an idea to formulate the blast design to control the backbreak. While vibration-based prediction models are commonly used to estimate backbreak, they require physical blasting experimentation. To overcome this limitation, the paper describes the development of a FE model using ANSYS Explicit dynamics, which simulates rock blasting and calculates the total deformation of the rockmass. The rockmass deformation is modelled using Drucker-Prager (D-P) strength model with the Jones-Wilkins-Lee (JWL) equation of state for the explosives. The accuracy of the FE model is evaluated through physical experiments, and the results are compared with the vibration models. The FE model demonstrates close proximity to physical observations as well as vibration model result in predicting backbreak, thereby offering a promising alternative to vibration-based prediction models. The primary objective of the study is to predict the response of the insitu rockmass to explosive blast loading and determine the effective rock breakage zone.

Jan 1, 2024

By Salah A. Taqieddin

In an open pit, or a quarry blasting operation, a muck pile of broken material of given size and quantities suitable to a load/hauling system is normally created at the foot of a bench. Fragmentation can be used to evaluate the efficiency of that blast configuration.

Jan 1, 1987

By Kenneth Eltschlager

Post-blast assessment techniques using off-site data which includes location, seismograph and photographic data were discussed during the Blaster’s Weekend at this year’s ISEE Conference. Blast and property locations with commonly available GPS units allow for the spatial relationships surrounding the blasting to be documented. When distances are coupled with the charge weight per delay, the scaled distance can be calculated to any structure for either compliance with the rules, or to project limitations. When blasting seismograph data is obtained, the scaled distances are then able to be plotted against ground and air vibration levels for post-blast assessment purposes.

Jan 1, 2007

By Lawrence Cheng-Kwang Hu

"Since the only available delay detonator in Taiwan is electric delay detonator, which can beaccidentally initiated by fire, i impact force, friction, static electric, lighting, radiotransmitter, and stray current etc., that always represent fatal threatens to the blasting crew.Fire, impact, friction can be Prevented by handling carefully; lighting also can be detectedwith proper instruments. But when a blaster find an unknown extraneous current in his welllaid down blasting cable; what a horror scence will be expected especially the electricdetonators have been connected already."

Jan 1, 1993

By Clara Godoy, Paulo Couceiro, Juan Navarro

The continuous automatization and digitalization of the different stages involved in any underground construction bring new possibilities to optimize the operation. One of the most important requirements for the development of these projects consist of a proper rock mass characterization for optimizing the stages of the drilling, blasting and support cycle. In the last few years the road to digitalization has gone through data science and big data, showing the importance of data gathered to describe the geological and geotechnical environment that surrounds the operations. Since rock characteristics have an important influence in the drilling response, the technological advances in the sensorization of drilling machinery such as the Measurement While Drilling system (MWD) allow to gather the necessary amount of information to be applied in data science processes to evaluate changes in the rock mass with higher resolution than conventional methods. In this paper, Machine Learning techniques have been used to combine data monitored from the drill rigwith scanner profiles of the excavated sections to develop an automatic geotechnical rock mass characterization model able to estimate potential zones of over- or under-break of the remaining rock mass in underground blasting. By comparison of scanner profiles of the excavated sections with the blasthole positions, an Excavated Mean Distance (EMD) between the contour blastholes and the excavated profile has been obtained, which may be considered as damage measure. Considering blasting factors as constant, the model combines the rotary, percussive, hydraulic flushing and the rate of advance of the drilling, and the confinement of the rock mass by depth, to detect zones with different rock properties. This provide an early information of the rock mass condition around the blastholes and the prediction of expected overbreak generated after blasting, being possible to design more efficient bastings, in which each borehole is filled with the right and necessary explosive charge. The analysis comprises data from 57 blasts (around 1700 contour blastholes) and more than 4000 excavated sections.

By Richard A. Dick

On August 3, 1977 the 95th Congress passed Public Law 95-87, the Surface Mining Control and Reclamation Act of 1977. This Act created the Office of Surface Mining Reclamation and Enforcement (OSM), which was given the responsibility of formulating regulations to implement the Act. This paper explains the rationale behind the specific provisions of the final blasting regulations, which were published in volume 44, No. 50 of the Federal Register, dated March 13, 1979. The major items covered by the regulations include preblasting surveys, blasting schedules, protection of the public, ground vibration limits, the scaled distance equation, airblast limits, blasting procedures, and record keeping. The regulations are designed to protect the safety and well-being of the public and to protect buildings and structures such as wells, pipelines, and storage facilities from damage.

Jan 1, 1979

By U Nyberg

Peak particle velocity (PPV) and distance measurements from a single-charge blast test conducted by Swedish researchers in iron ore at the Kiruna Mine in northern Sweden are presented. They are used along with theoretical PPVs calculated using an equation based on hydrodynamics to determine a damage distance range caused by a single charge. This equation, which relates PPV to explosive properties, charge geometry, and distance from a charge, was then applied to a charge of different geometry that was used in drift rounds. A comparison between calculated and measured PPVs suggests that the stoping holes likely damage the easer hole locations, and the easer holes produce damage to the perimeter hole locations. The practical effect is that typical damage limit predictions based on measurements conducted in fresh or undamaged rock are conservative. This suggests that even when perimeter control is not exercised in drifting (i.e., the perimeter holes are fully loaded), the resulting damage may be less than normally expected due to the wave damping effect of the pre-damaged rock. Due to the damping effect, poor perimeter blasting practices are somewhat self correcting. However, it must be strongly emphasized that well-engineered blast designs with perimeter control are highly beneficial in relation to both economic and safety aspects.

Jan 1, 2011

By Joe Dannenberg

One must be cautious in talking about blasting safety, because the very act of making a blast involves the creation of an infernal machine. You are setting up for the instant release of tremendous energy. Inherently this is a hazardous act. It has always been hazardous. It will stay hazardous.

Jan 1, 1975

By John R. Holliday, William Marcum

Apogee Coal Company, DBA Arch of West Virginia, faced the challenge of drilling and blasting over one million cubic yards of high temperature overburden at its Ruffner surface operation near Logan, West Virginia. The overburden was removed above the Upper Five Block seam that was previously deep mined, abandoned, and later engulfed by fire. Borehole temperatures were measured above 700° F.

Jan 1, 1996

By Richard J. Mainiero

Traditional techniques for the experimental determination of toxic fumes produced by the detonation of high explosives are not applicable to blasting agents. To detonate properly, blasting agents require confinement, a significant booster, charge diameters of 3 inches (7.5 cm) or greater, and charge lengths greater than two times the charge diameter. Without these conditions, blasting agents will not detonate at full order, leading to a misrepresentation of the gaseous products.

Jan 1, 1997

By Changa-Ha Ryu, Hae-Moon Choi, Sang-Don Lee

The rock mass to be excavated is classified using data obtained from the initial site investigation, and the design of excavation and support is then made based on the rock class. Rock classification provides an empirical design with guidelines for tunnel support compatible with rock mass quality and the method of excavation. Although most clients provide standard patterns corresponding to each rock class, the patterns of drilling and blasting have only been used in estimating the excavation cost and not used in the construction stage. The purpose of the study presented in this paper is to establish a standard blast pattern to yield optimum blasting performance along with an attempt to reduce a difference between design and construction. A series of test blasts were carried out at two tunneling sites of Central Inland Highway crossing the country. Long hole blasting was tested in rock mass whose RMR value is over 60. The blasting results were evaluated by measuring degree of fragmentation, advance rate, muckpile distribution, overbreak, etc. Based on the results of test blast, several patterns were proposed for a twolane highway tunnel.

Jan 1, 2005

By Cameron McKenzie, John Heilig, Patrick Andrieux, Andree Drolet

It is widely accepted that both underground and surface blasting operations can de-stabilise excavations to the point where it can threaten the feasibility of mining through personnel safety or OK dilution. Research has been undertaken to outline a practical method in which the impact of blasting will be accounted for during the early excavation design stage by modelling, and during the following production stages by monitoring rock response to blasting operations.

Jan 1, 1994

By Lon D. Santis

This paper presents data and theorem to calculate the risk of experiencing undesirable lightning related events while blasting or while engaged in other lightning sensitive activities. The paper provides an overview of lightning hazards in blasting operations and a brief history of lightning related blasting accidents. Lightning continues to be the primary cause of premature initiations of explosives in mining; on average, over two such incidents are reported to the Mine Safety and Health Administration (MSHA) each year. The energy contained in lightning discharges and how this energy sets off explosives in mining is presented. Three categories of lightning warning methods: public media, lightning detectors, and atmospheric electrostatic field measurement are discussed. The remainder of the paper presents recently acquired data on the spatial characteristics of lightning development. This data is used to estimate the risk assumed by blasters under certain conditions. Risk estimations are made for electric and nonelectric blasting if persons are evacuated when cloud-to-ground (c-g) lightning approaches within a certain distance. For example, about 0.6% of all c-g lightning strikes have no other c-g lightning strikes within 25 miles in the previous 30 minutes. The paper shows that a typical blaster using nonelectric initiation in a high lightning density area with a 100% accurate lightning detector set to alarm at 25 miles would have a lightning caused unplanned detonation every 14,000 years.

Jan 1, 1998

By Richard J. Mainiero, Michael S. Wieland, Harry C. Verakis

The Bureau of Mines, U.S. Department of the Interior, has been conducting research on delay blasting in underground coal mines in support of the efforts of Mine Safety and Health Administration (MSHA), U.S. Department of Labor, to revise coal mine blasting regulations. Part of the research centered on developing an understanding of the factors that lead to misfires of permissible explosives. Research was conducted to determine whether frequency of misfires was related to borehole spacing. For a wide variety of permissible explosives, misfires were observed for about 50 X of the holes at 45-cm (18-in) spacing. Misfires were also observed for 60-cm (24-in) spacing, but the frequency of misfires was much lower than observed for the 45-cm (18-in) spacing. The Bureau has recommended that hole spacings of less than 60 cm (24 in) be prohibited.

Jan 1, 1986

By Harry Verakis, Thomas Lobb

Widespread use of ammonium nitrate compositions for mine blasting operations has led to various bulk transport vehicles designed especially for the explosives industry over the past half century or more. The advancements in explosives technology and continuing developments in bulk transportation have resulted in a variety of blasting agents and, more recently, oxidizers being transported and used from specially designed bulk transport vehicles. It is estimated that about 2000 bulk transport vehicles are used in mining operations. Many of the bulk vehicles carry about 15,000 to 33,000 pounds (6808 to 14,968 kilograms) of payload and some can carry up to 50,000 pounds (22,679 kilograms) for large open cast mines. Thus, it is imperative that detailed knowledge and safety instructions are available from the blasting personnel and mine management should an unplanned incident such as a fire occur with a bulk transport vehicle at a mine site.

Jan 1, 2008

By Sehoon Lee, Duhwoe Jung, Eunsu Cha, Kyeonghwan Jeong

This case study presents the effectiveness of underground rock blasting to facilitate the trench cut in the hard rock layer using a conventional trench cutter for the construction of a diaphragm wall. Rock blastings are pre-performed up to the scheduled depth and then the fragmented rocks can be easily cut using a conventional trench cutter. Two trial underground rock blastings have been performed and the effectiveness of pre-blasting is presented in terms of a cutting rate, a loss of cutter heads and an amount of overbreak. Based on the results obtained from the trial underground rock blastings, the following conclusions can be appropriate: 1) A pre-blasting of hard rock layer located in depth can help to overcome the limitation of the trench cut using a conventional trench cutter. If the hard rock layer is fragmented after blasting, the fragmented rocks can be easily cut using a conventional trench cutter, 2) The speed of cutting works was accelerated and the loss of cutter heads was significantly reduced in the sections where the blastings were applied prior to cutting. 3) The amount of overbreak, expressed in terms of the amount of poured concrete, can be reduced to some extent. However, the location of blast holes in the trench can also contribute to the amount of overbreak. The closer the location of blast holes to the edge of the trench, the more extensive fractured and cracked zone can be formed on the face of the trench. This can increase the amount of overbreak if the trench is left empty for a while.

Jan 1, 2000

By Mario Karfakis, G. Langlois

Well stimulation is the process by which any production well, whether for production (extraction), storage (injection) or deep interaction (remediation, monitoring, etc) can be made or stimulated to flow at higher levels. This stimulation is driven by active methods to increase the permeability in the near-well environment and create a larger zone of communication between a well and the reservoir it services. Well stimulation is a crucial aspect of well completion and reservoir engineering and is a subject of careful pre-drilling planning. In many modern industrial endeavors the effectiveness of well stimulation is often critical to economic viability. Because of the broad impact of well engineering on several large industries (petroleum and natural gas extraction and storage, geothermal power, groundwater monitoring, extraction and management, environmental remediation, mining and minerals extraction, etc.) changes in the state of the art in well engineering and well stimulation can affect the capabilities of very diverse and disparate industries. This paper is an effort to communicate the status and effectiveness of current practice and technology in well stimulation. The intention being that effective communication of progress can spur innovation in industries that require well stimulation but are removed from immediate communication of technological or practical improvement.

Jan 1, 2009

By B Mohanty

Full-face blasting rounds have been used to excavate a 4.6-mdiameter shaft at Atomic Energy of Canada Limited's Underground Research Laboratory near Pinawa, Manitoba. Both standard pyrotechnic delay detonators and the newly developed electronic delay detonators (EDD) were used on the project. The full-face blasting technique, employing 89-mm-diameter relief holes and 38-mm diameter blast holes, NG-based explosives, and the regular long period delay detonators, has been standard practice at the site, giving excellent wall control and fragmentation results. The comparison blasts using pyrotechnic detonators and EDDs were carried out to test the operational logistics, timing accuracy and blast results obtained with the latter. The long period pyrotechnic delays ranged from O to 18, with the nominal delay varying between 350 ms and 800 ms. The EDD blasts used the same number of periods, with the respective delay interval between successive periods set precisely at 190 ms and 210 ms for the two blasts. Based on a broad range of critically assessed parameters, the EDD blast results proved to be signficantly superior to those obtained with regular pyrotechnic detonators. The results have been analyzed in detail and the relative merits of the two delay systems have been determined. Alternative designs to derive maximum benefits from EDDs in shaft and tunnel blasts have also been suggested.

Jan 1, 1990

By William D. Hissem

The purpose of this paper is to advise people about the methods, use, and possible applications of current "personal computer" hardware and software with regard to the economic cost analysis of percussion drilling equipment. The material content and orientation of this paper is toward those people who have just begun "PC" (personal computer) operations, and (or) those who are considering their use.

Jan 1, 1986