Search Documents

By A. D. Fowler, M. T. Anderson

A phenomenological model is presented that relates Pb-Zn mineralisation to proximal geopressure zones. Typically, geopressure zones (GPZ) consist of masses of undercompacted sediment encapsulated within impermeable shales and are characterised by high formation fluid pressures. Heat flow is perturbed in some GPZ on account of their insulating properties. Geothermal gradients as high as 150 degrees C/km have been observed over short distances in the sediments of the US coast of the Gulf of Mexico. Some modern geopressure zones are known to reach temperatures of 120-150 degrees C at depths of 2.5-3.5 km. It is demonstrated that the zones may act as proximal sources of hydrothermal fluids, thus explaining the high temperatures of mineralisation observed in the deposits, which are hosted in basins characterised by thick, rapidly deposited, shale-rich clastic sequences

Jan 1, 1991

By B. S. Terry, C. L. Harris

After measuring the kinetics of Ni reduction from a SiO2-saturated fayalite slag into a Cu-based metallic phase on a laboratory scale, a general model was developed that is capable of simulating mass transfer to and from metal-slag, slag-gas and metal-gas interfaces for multiple species. The model was used to simulate the reactions that occur when Cu and Ni are reduced from fayalite-based slags into a Cu-based metallic phase. Good agreement was achieved between model predictions and experimental data

Aug 1, 1995

By G. D. Schena, M Zanin

A numerical approach is presented for predicting the liberation of phases during comminution, with direct calculation of a liberation spectrum giving the fraction of the particulate system in each narrow size-composition class. The numerical model uses a Poisson flat process for stochastic generation of the non-convex three-dimensional Poisson polyhedral textures and the system of fractures that give rise to convex fragments. With this numerical approach, there is no need to assume random uniform isotopic fracture (lack of selective liberation); only computational geometry primitives are exploited for the derivation. The agreement with relationships obtained previously under the random uniform isotopic fracture hypothesis demonstrates that the approach is capable of deriving full liberation spectra directly. Both volumetric and superficial composition can be calculated

Jun 21, 1905

By T Atkinson, A Cobb, R AJIington

Risk management is concerned with the whole spectrum of financial, geological, engineering, legal, governmental, social and occasionally ethnic issues, concerned with mining projects. The inherent risks in mining operations are well publicised, but new issues and hazards arrive on the scene and lake precedence, but the older risks still remain, while insurance cover may not he ‘full cover’ in the future. It has long been recognised that quantitative approaches to risk analysis can play a major role, but although these methods are capable of considerable theoretical precision, the lack of sound risk input data and experienced personnel limits the usefulness of theoretical analysis. It can, however, greatly assist in comparing cases, in identifying areas of risk and help in the investment decision process. Its major contribution to a mining project is that it imposes an investigative discipline that also assists in improving the quantitative approach to risk analysis and hence risk management. Risk analysis and risk management also requires sound common sense and major inputs from experienced geologists, mining, mechanical, electrical and mineral processing engineers. The Engineering Council, in 1992, issued a ten point code of professional practice entitled ‘Engineers and Risk Issues’ (The Engineering Council. 1992), covering our professional responsibilities, the law, our conduct, the need for a systematic approach to risk issues, the use of professional judgement, communications, risk management, evaluation of risk, our professional development in this field and the encouragement of public awareness of risk issues. This is a specific area of training perhaps long neglected by our industry and academic institutions (Atkinson. 1983).

Jan 5, 1996

Paper presented at the UK minerals industry conference and published in: Minerals extraction towards the millennium. UK minerals industry conference, 3-5 April 1995, University of Leeds. London: Institution of Mining and Metallurgy, 1995. The various types of risks that arise in minerals industry projects are usually financial, technical, or environmental, and the key to valid risk analysis is complete integration of all risks, both within and between categories. Geographical information systems (GIS) and geostatistical simulation methods can provide a means of integrating data and conducting realistic risk analyses. Risk can be quantified but there are limitations to numerical approaches to risk assessment. Realistic quantification requires adequate models of the processes that give rise to risk. Risk perception must also be taken into account when conducting risk assessment and reporting the results, especially in public forums. The modelling and visualisation capabilities of a combined GIS/simulation system can provide the means of dealing with perception in risk analysis

Jun 19, 1905

By M. Gallego, R. Oyarzun, L. Ortega

Evidence of metallogenic activity in an area dominated by Upper Precambrian and Palaeozoic metasediments was partially explained in the 1980s when drilling and a geophysical survey detected hidden intrusions, but questions remained to be answered about the nature of the fluids. Sb mineralisation at El Juncalon vein-type deposit was selected for geological, geochemical and fluid inclusion studies as a model with a relatively simple quartz-stibnite-pyrite paragenesis. Many of the characteristics were those of Chinese-type vein Sb deposits, which can be regarded as atypical of the epithermal type as they are hosted by clastic rocks

Aug 1, 1995

By T. G. Carter, R. I. Miller

First, the influence of variation in the

Apr 1, 1995

By Xuejing Xie, Tianxiang Ren

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). Standardised stream-sediment sampling procedures have been used in mountainous and hilly terrains. Special sampling procedures were developed for application in remote environments, such as high mountains, desert, semi-desert, karst and loess-covered regions. The diversified analytical methods used in more than 20 analytical laboratories participating in the project have been unified into two multi-element, multi-method analytical systems. A unified data monitoring procedure was developed based on primary and secondary standard samples. To date the project has covered about 4 000 000 km2 and the aim is to complete the coverage within the present decade

May 1, 1991

By J Kokado, N Hatta, S Yabushita

A theoretical model is described for prediction of the capacity of fines from porous ores, such as cokes and sintered ores, to be removed by a pneumatic, horizontal-type classifier prior to charging into a blast furnace. First, the influence of variation in the apparent density and drag coefficient of porous ores on removal efficiency is analysed from a stochastic standpoint. The effect on efficiency of collisions between particles in the classifying region is then examined analytically in relation to the ratio of the mass flow rates of particles and air (the loading ratio). Finally, a theoretical model is constructed that takes these factors into account. Theoretical and experimental results are compared and classifying efficiency is discussed from both experimental and theoretical viewpoints.

Dec 1, 1993

By Qing Wang, H. Sevim

Belt network simulators are the most widely used models in the design of belt networks. The simulators developed in the past two decades are reviewed and their limitations are discussed. To overcome these limitations and to provide a design model that can be used efficiently in real-life applications, a comprehensive non-simulation model has been developed. The features of this model are briefly discussed. A real example is used to demonstrate the model's superiority over belt simulators

Sep 1, 1991

By R. Ciccu, P. P. Manca, A. Bortolussi, G. Massacci

Tool performance and the unit cost of cutting depend on a number of operational variables (peripheral velocity, pull-back force, water injection rate, angles of the sections of wire outside the rock) as well as on the geometric features of the cut itself (area and shape). Cutting rate and wire productivity are also influenced by the type and number of diamond beads per unit length of wire and by the characteristics of the rock (granite or marble). A computer program aimed at handling a problem of this complexity has been developed and tested with the use of available field and laboratory data and has been found acceptably reliable. Discrepancies between current industrial data and some of the results suggest future lines of research, while the simulation should also be extended to include different types of rock and tool and a variety of bench face geometries

Aug 1, 1994

By J. A. Hudson, D. L. Millar

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993 (original title: Rock engineering system performance monitoring using neural networks.) Synthetic and analytical approaches to objective-based design of rock engineering projects are discussed. Rock masses are considered as complex dynamic systems with components that concurrently interact with each other and their environment. The existence of a rock engineering system canon (i.e. a set of systems governing rules) is proposed. Its possible components are highlighted and an application is demonstrated using a "rock mass automaton" designed to simulate dynamic heat distribution in rock. In the example given, the canon implements the basic result from probability theory applied to the thermodynamics of solids. Rock engineering system performance is reduced to the mapping of the output of a rockmass to varying input (design) options, within the state space of the systems model. The Kohonen Self-Organising Map provides an extremely useful analytical tool to reduce the hyper-dimensionality of rock engineering system behaviour. Further, the hyper-dimensional state vector is mapped "quasiconformally" such that the neural map tends to spatially organise similar input state vectors, facilitating interpretation of rock engineering system behaviour (performance monitoring). Work is reported on the development and validation of the automation as a basis for an internal representation of the rock mass bahaviour. The results are reported of simulations compensating for the uncertainty of the exact mechanisms operating within the rock mass, using additive noise with the input state vector in the training stages of the self-organising map implementation. Initial work on adopting Grossberg's Adaptive Resonance Theory neural network architecture for classification of rock engineering systems behaviour is also presented

Apr 1, 1994

To maximise recovery by highwall mining, pillars must be designed which are long, slender and of relatively low width-to-height ratios. The strength of pillars with width/height less than 2 depends primarily on the mechanical response of the coal, due to the reduced influence of frictional restraint between roof and floor. A suitable pillar design approach therefore requires a method of estimating coal-seam properties. Experimental studies were carried out to determine ways of reliably predicting the large-scale mechanical properties of coal seams from small-scale test data. The studies led to a method of practical, systematic assessment of coal-seam properties based on measurement of coal rank and seam brightness profiles. The criterion employs the parameters sigma(c), m and s of the generalised Hoek-Brown empirical strength criterion for rock masses. A novel design approach combines the flexibility of modern numerical modelling programs with simple hand calculation for rapid assessment

Jun 21, 1905

By R. W. Ruddle

The present state of knowledge on this subject may briefly be summarized as follows: (1) The copper content of the slag increases with the grade of the matte in contact with it; on the other hand, the proportion of copper lost decreases as the matte grade increases, because as a general rule a smaller volume of slag is produced when a high-grade matte is made. (2) The presence of CaO and MgO in the slag decreases the copper content of the slag, and the presence of ZnO increases it; the presence of A1203 seems to have little effect. The influence of the silicate degree is not yet clarified, but on theoretical grounds it seems likely that the copper content increases with the silicate degree of the slag. (3) High slag viscosity, high magnetite contents and low density difference between matte and slag all tend to increase the copper loss. The volume of slag is also an important factor. (4) The effect of bath temperature on the copper loss is not clear and further investigation of this point is needed. (5) It appears possible to recover a large part of the copper in the slag by adding FeS, CaS and other sulphides

Jan 1, 1953

By R. G. Jones

At its peak in the 1970s, South Africa was responsible for around 80% of global gold production and, according to the US Geological Survey, it still has the largest share of gold reserves - as well as 90% of the world's platinum. But, in January 2015, gold production reached a new monthly low, generating 87% less than it did in January 1980, and South Africa is now the world's sixth ranked gold producer. What next for African gold?

Jun 1, 2015

Discussion following the presentation at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 8th April 1916, included the author's introduction, written contributions by Bedson P.P., Gregory T.W.D. and Morgan J.D., oral contributions by Louis H., Greener T.Y. and Severs W., and the author's reply

Dec 1, 1916

By M. J. Scoble, L. M. Daneshmend, C. Hendricks

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993. An attempt is made to relate emerging technologies to education and training requirements by examining the nature of the Canadian mining industry's human resources. Particular attention is given to the trends evident in mine automation and their likely impact on instructional needs. The characteristics of "computer-aided instruction" systems are reviewed and related to the implementation and support of mine-wide monitoring and communication networks, which are seen as fundamental to the eventual automation of underground hardrock mines

Apr 1, 1994

By G. Zhan, P. Mousset-Jones, G. Danko, J. J. K. Daemen, C. Mezei

Paper presented at the conference Risk assessment in the extractive industries, held in Exeter, 23-24 March 1994, and first published London: IMM, 1994, preprint volume. 18pp., 12 refs. (Originally entitled: Tunnel roof diagnosis using a robotic sensor test bed.) An integral roof diagnosis method is proposed to assist in assessment of risk regarding the stability of an excavation. A Robotic Sensor Test Bed (RSTB) is being developed for the characterisation of roof stability. The sensor test bed consists of a sonic/ultrasonic wave response sensor, a laser surface profiler and a surface temperature sensor. These sensors are mounted on an articulated robot manipulator for performing remote-controlled or fully automated diagnoses. A number of laboratory and field sonic/ultrasonic tests were conducted. A high-energy ultrasonic transducer and an impact device were used to resonate rock slabs. The fracture depths of the slabs were found to be inversely related to the measured resonance frequencies. The agreement between identified and actual dimensions was acceptable. Field tests also showed that loose rock on the surface can be clearly distinguished from solid formation by comparing their wave responses. The robotic laser profiler part of the RSTB was used to measure surface geometry. Different scanning methods are being developed to achieve the fastest and most precise measurements and to provide pertinent information about rock joints and major fractures

Dec 1, 1994

By P. A. Rossouw, G. A. Fourie

Several attempts have been made over the latter half of the twentieth century to devise a system for the classification of underground mining methods. None of these are found to be totally successful. A revised classification is suggested with three main categories being identified by reference to fill requirements, steep stopes and stratified geological environments. Methods always needing lasting mass or structure fill include methods with timber-structured stopes and those with mass-filled (or cut-and-fill) stopes. Methods associated with steep stopes are subdivided into steep-stope-specific caving and steep-stope-specific non-caving (or self-supporting) methods. Methods not in the first two categories, often used in stratified geological situations, are not necessarily restricted to stratified environments and include caving as well as non-caving varieties. This category is further divided into room-and-pillar mining, longwall and shortwall coal mining and the type of open stoping found in gold or platinum reefs comprising overhand, underhand and breast-stoping variations

Dec 1, 1996

By A. J. Naldrett

"Synorogenic mafic intrusions are a common feature of the northern Appalachians. Two sulphide-bearing intrusions in central Maine that have been investigated revealed a number of important features that illustrate sulphide-silicate interaction that relates to magmatic sulphides. The Moxie Pluton is a large mafic intrusion emplaced during the Devonian Acadian orogeny. The Katahdin gabbro is a small mafic body that is probably genetically and temporally related to the Moxie Pluton. Both intrusions were formed bv the intrusion of variably fractionated magmas into irregular chambers and feeder zones. The southern half of the Moxie Pluton contains three small sulphide accumulations, whereas the Katahdin gabbro hosts a large, predominantly massive, sulphide body. Textural evidence clearly documents the magmatic origin of these sulphides.The three Moxie Pluton sulphide bodies are located at or very close to the intersection between the intrusion and the sulphidebearing Hildreths Formation. Sulphur assimilation, suggested by this relationship, is supported by the isotopically light (634S = —8 to —25) and the selenium-poor (S/Se - 25 000-48 000) character of the Moxie sulphides and correlation with the Hildreths Formation sulphides (S34S = —25, S/Se = 25 000-48 000). Isotopically light sulphur (534S = —20 to —21) and high S/Se ratios indicate that the majority of sulphur in the Katahdin sulphide body was also derived from an unexposed country rock source. The volume of sulphide in this example illustrates the potential efficiency of the sulphur assimilation process—so efficient in this case that marked dilution of the economic chalcophile elements resulted from the addition of so much external sulphur.The three Moxie Pluton sulphide occurrences are all impoverished in Ni and Cu (1.87-0.44% Ni; 0.72—0.32% Cu in massive sulphide), but contain normal Co contents (0.22-0.13%) relative to typical magmatic sulphides. The Katahdin sulphides show a greater Ni and Cu impoverishment (0.2% Ni; 0.1% Cu in massive sulphide) with similar Co (0.17%). The Ni content of the Moxie Pluton olivines document the fractional removal of sulphides during crystallization of the host magma, which resulted in the progressive depletion of the chalcophile metals in this magma. Modelling that involved the fractional crystallization of the magma coupled with the fractional removal of a specified proportion of sulphide has successfully duplicated the Moxie Pluton sulphide compositions. A similar magmatic model has been postulated for the Katahdin sulphides with a greater degree of sulphide fractionation. This latter model is again supported by extremely low Ni/forsterite ratios in olivines, though the compositional range is insufficient to document fractionation. These magmatic models are not unique, but they provide a relatively constrained and consistent explanation for the sulphide compositions.The Ni contents of olivines are the most important indicator of sulphide-silicate interaction in mafic magmas and have exploration potential. They provide a means of assessing the timing and extent of sulphur saturation in an intrusion and are a guide to the Ni content of a sulphide accumulation in equilibrium with olivine. In the Maine examples they provide strong evidence of the magmatic origin of the sulphide accumulations and justification for magmatic modelling."

Jan 1, 1984