Search Documents

By A. Paulin, A. W. D. Hills

The work has shown that packed-bed behaviour can be predicted from the results of single-particle experiments, total reaction times being predicted somewhat more accurately than gas and solid temperatures and gas compositions. A small laboratory packed-bed reactor was built and used to study the decomposition of beds of specially prepared CaCO3 spheres, steps being taken to minimise the effects exerted by the walls of the bed on processes occurring within the bed. Gas and solid temperatures and gas compositions were measured at various points in the bed and compared with theoretical predictions based on kinetic data determined in previous single-particle experiments. The measured solid temperatures and total reaction times agreed remarkably well with the values predicted theoretically. Gas and solid temperatures measured after the reaction had finished at any point in the bed did not agree with the theory. This was because solid temperatures in the bed rose very rapidly once the reaction was completed and the walls of the bed could not be heated at a sufficient rate for their temperatures to rise as rapidly; thus some loss of heat from the bed to the walls was inevitable, and this could not be accounted for in the theory. In addition, the theory did not allow for the conduction of heat within the bed, and this resulted in some further slight discrepancy between the measured and predicted values, particularly after the reaction was completed. Gas compositions measured in the bed were rather scattered, but, even so, they agreed moderately well with the predictions of the theory.

Dec 1, 1971

By D. J. Allan, W. R. Wilson

For conventional aerospace aluminium alloys of the 2000 (copper) and 7000 (zinc, magnesium) series the recycling of process scrap from both metal suppliers and aircraft manufacturers is a well-established, worldwide industry. The recent introduction of a new family of alloys that incorporates lithium has posed a new challenge to the recycling industry owing to the high cost of lithium, its high reactivity to the atmosphere and to refractories and its absence from the specifications of all other registered alloys. Various process options for recycling have been identified, but vacuum distillation has been selected as the most cost-effective and technically feasible solution. Experimental work established that the separation of Li from AI-Li scrap is feasible and an industrial process has been designed. The economics of Li recovery are very sensitive to the AI-Li content of the feed material. Owing to the design of aerospace vehicle manufacturing plants it is expected that the swarf will be mixed with other alloys. A method of enriching this feed has been developed that is based on the control of swarf morphology by thermal and mechanical treatments as a precursor to eddy-current separation. After eddy-current separation and vacuum distillation small proportions of Li are retained in the AI residue. The effects of this on the properties of conventional AI-Si shape-casting alloys were investigated and safe threshold levels have been established.

Jan 4, 1993

Jan 1, 1947

By L. Wade, R. Wang, M. A. Horton

Laboratory methods to find the mechanical properties of rock are inherently biased towards stronger strata, which best survive the sample preparation process. Geophysical techniques are not subject to such bias and may be used to predict mechanical properties rapidly and cheaply. Samples (151) were obtained from a borehole that had been comprehensively geophysically logged. The mechanical properties of the samples were established in the laboratory and correlated with the geophysical responses of the strata from which they came. The results indicate that, for homogeneous strata at least, it is possible to predict the unconfined compressive strength reasonably well from sonic travel time measurements made in the field. Predictions of static Young's modulus may also be made from this data source, but with a lesser degree of confidence. A multivariate regression equation is presented which relates down-hole sonic travel time to unconfined compressive strength, depth and the frequency of fractures in the rock mass. This equation may offer potential for the prediction of the mechanical rock properties of fractured and layered strata.

Jan 4, 1993

By E R. Hassall

Discussiong the importance of minerals and mining, impacts on the environment and remediation, and the need to foster interest in science among young people.

Jan 8, 1997

By Ruddle R. W.

Magnetite occurs in the reverberatory furnaces, blast furnace and converter (a) as the result of its presence in the materials charged, and (b) as the result of oxidation of the FeS in the charge in the absence of sufficient SiO2 to slag the FeO as it is produced and thus prevent its subsequent further oxidation. Magnetite is reduced by FeS according to FeS+3Fe3O4=10FeO+SO2 and similar reactions. This reaction is markedly affected by temperature and does not proceed to any important extent below about 1200°C. To ensure comparative freedom from magnetite it is therefore necessary to raise the temperature of the furnace to the highest practicable figure and to use plenty of siliceous flux. Since the maximum operating temperature is likely to be limited by the resistance of the refractories to attack by the slag, investigation of the factors affecting this attack should be helpful. It is reasonable to suppose that the formation of magnetite might be minimized by ensuring intimate admixture of matte and slag during conversion so that silica is readily available for combination with ferrous oxide as the latter is formed. The literature gives no clue to the importance of this factor and some experimental work on this aspect might be fruitful

Jan 1, 1953

By D. V. Venugopal, W. W. Gardiner

Spessartine-quartz rocks are manganiferous sedimentary rocks rich in spessartine and quartz which occur in north-central New Brunswick. They represent a recrystallised manganiferous siltstone/chert that is contained in or associated with red manganiferous siltstone (RMS) units. The spessartine-quartz rocks and RMS form part of an Ordovician volcanic and sedimentary succession within the Appalachian-Caledonian orogen which hosts numerous massive sulphides and polymetallic vein deposits. The New Brunswick spessartine-quartz rocks are spatially and temporally associated with stratiform base-metal, precious metal and hydrothermal tin-tungsten deposits. This suggests that spessartine-bearing lithologies and zones can be useful in predictive metallogeny and for the understanding of the stratigraphy and palaeographic setting of the early Palaeozoic rocks of the Appalachian-Caledonian orogen.

Jan 12, 1992

By Tawsaporn Nuchanong, Ian Nichol

Investigations of the dispersion of gold in soils and stream sediments associated with three gold deposits in Thailand indicate the existence of different geochemical dispersion patterns in the three areas, demonstrating the need for the adoption of a variety of exploration techniques. The three gold deposits which were investigated were the Phu Tham Phra-Phu Thong Daeng copper-gold prospect, the Doi Tung and the Huai Hin Lab gold prospects. Overall the investigations at the three localities demonstrate clearly that the chances of exploration success can be significantly enhanced if composite soil samples are analysed to ensure a more reliable estimation of the gold content in soils and if both the 63 micrometre fraction and the field-panned concentrates of stream sediments are analysed because of the variable grain size of the gold characterising different gold deposits and surface environments.

Jan 4, 1992

The paper, presented at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 8th April 1916, presents experimental work undertaken to observe the quenching effect of different substances, to find the most efficient of these substances, and to arrive at a possible explanation of their preventive action. The coal-dusts experimented with were such as passed through a 100-mesh sieve (10,000 holes to the square inch), and were obtained by grinding the coals. The quenching substances, used in as fine a state of division as possible, included gypsum, dried Chance mud, quicklime, magnesia, magnesia alba (levis), anhydrous sodium carbonate, sodium bicarbonate, soda-crystals, Glauber salts, ground shale and boiler-ashes

Dec 1, 1916

By S. K. Chaulya, R. S. Singh, B. B. Dhar

Two prominent local species, Dendrocalmus strictus (bamboo) and Saccharum spontaneum (kashi), and two exotic species, Cymbopogon citratus (lemon grass) and Vetiveria zizanoides (vetiver), were selected for growth trials on dumps at Mandaman, Chora, Mudidih, South Balanda and Ghugus. The climate at these sites is dry tropical and the surface soil layer a slightly acid to neutral sandy to clayey loam 10-11 cm thick, impoverished in major plant nutrients. After two years bamboo had grown the most, up to 325 cm in height, and contributed the greatest biomass, 638 g/m2 of plant. The local kashi species had a very good regenerative capacity, which was lacking in the lemon grass and vetiver. The grasses had very good soil-binding capacity and could also provide income if used as cash crops

Jun 21, 1905

By C. J. V. Wheatley

Recent studies of the mineralisation at Avoca in southeast Ireland, Parys Mountain in Anglesey, and Coniston in the Lake District result in the proposal of a new metallogenetic model for mineral deposits in the Southern Caledonides. A regional pattern of metal zoning exists, an axial belt, including the major copper deposits, being bordered by areas with lead-zinc deposits. Conformable lenticular pyritic zones occur in the central belt, closely associated with acid volcanic sequences and, often, post-dating them. These zones are thought to have been formed in a marine environment, mineral growth taking place below the sediment-water interface, whereas magnetite-rich zones developed under different Eh and pH conditions. Stockworks containing appreciable copper and, in some cases, lead and zinc were developed at a later date, stratigraphically below the pyritic zones, by migrating hydrothermal chloride and metal-rich fluids. Complex lead-zinc-pyrite mineralisation resulted from the reaction between pyritic zones and the final fraction of the hydrothermal fluids. Crosscutting vein-type fissure infilling mineralisation occurs in every mineral field. These deposits apparently comprise a pulsatory metasomatic sequence, closely related to tectono-stratigraphic controls, ore localisation being influenced by the coincidence of suitable structures and pyritic shale horizons. The implications for mineral exploration are considered and it is concluded that the model offers an explanation for the existing pattern of metal zoning; and it may have wide applicability to mineral deposition in geosynclinal sequences.

Dec 1, 1971

By R. I. Jeffery, J. W. Summers

An account is given of the verification and calibration of a numerical modelling technique that has been developed for the prediction of subsurface strata deformation following the extraction of coal by longwall mining methods.

Jan 4, 1992

Discussion of the papers with a written contribution and authors' written replies.

Jan 1, 1947

By B. D. Rayment, J. D. Wilson, G. R. Davis

Wheal Jane, situated between Truro and the Carnmenellis granite, is under development by Consolidated Gold Fields, Ltd., as a tin producer. The main or B lode comprises a complex cassiterite-sulphide ore located in shear zones along the footwall of the lowest of a series of porphyry dykes (elvans) which strike ENE and dip 35° north. Minor mineralisation follows other elvan contacts and sets of later steeply dipping fractures. The localisation and overall geometry of the deposit is explained in terms of the complex structural geology of the Lower Palaeozoic metasediments and the shape and manner of emplacement of the invading Hercynian granite of Cornwall. Variations in the thickness and grade of the orebody, and in the nature of the mineralisation, are shown to be structurally controlled by undulations of the footwall contact of the B elvan. Wallrock sericitisation is present and is applied in exploration for ore

Dec 1, 1971

By P wade

This is the first Presidential Address given to the Nottinghamshire Branch of The Institution following the merger of the Nottinghamshire and North Derbyshire Branch of The Institution of Mining Engineers (IMinE) and the Midland Branch of The Institution of Mining Electrical and Mining Mechanical Engineers (IMEMME). I intend to review the formation of the individual institutions as well as what has been achieved by mining related institutions over the years and finally I intend to look to our future.

Jan 11, 1996

By Q. H. Liao, B. G. Monaghan

The options for designing slopes in complex geological conditions are reviewed. It is shown that modelling, especially numerical modelling, allows a degree of analysis that cannot otherwise be achieved. Examples are presented of how numerical modelling can be used to investigate fundamental aspects of rock mass behaviour. It is demonstrated that an important consequence of change in scale is that the mechanisms of failure also change. The complex failure of the footwall slope at Aznalcollar, a large open-pit mine in southern Spain, is discussed. Numerical modelling with UDEC (universal distinct-element code) has allowed the realistic simulation of displacements measured in the field

Jun 18, 1905

By Y. L. Ding, N. A. Warner

Cylindrical pellets made from graphite and chromite mixtures were reduced in high-carbon ferrochromium melts at 1 600-1 695 degrees C, under an atmosphere of almost pure CO. The reduction rate, as measured by gas evolution, increased with increasing melt temperature and graphite addition and with decreasing pellet diameter or height, although reductant particle size had a very limited effect on kinetics. At a pellet size, heat and mass transfer were significant in controlling the early stages of reduction of large pellets while at chromite grain size, gas diffusion was probably a rate-controlling step. The time required for dissolution of unfluxed pellets into the melts was significantly longer than that for reduction. This indicates that pellet dissolution may be the limiting factor in determining the operating parameters for a proposed new process to produce high-carbon ferrochromium using melt circulation

Jun 19, 1905

By M. Schwartz

Mining in Argentina is diverse in terms of the number of minerals extracted from the country, but also in terms of the varied approaches and attitudes of mining investors and their trust in the country's individual provinces. Laws are discussed, investment attractiveness and taxation.

Jun 1, 2015

By D. J. Reddish, B. N. Whittaker, G. X. Sun

An image analysis technique has been used in the assessment of subsurface fracture levels in the context of water inflow into longwall mine workings. The technique was used to analyse results from physical modelling which are represented by black and white photographs taken directly from the model tests. Binary images of fracture patterns are obtained by scanning the photographs with an image analyser coupled to a video camera. The images are manipulated by a C program which allows them to be processed in vertical and horizontal directions and filtered to differentiate quantitatively between vertical and horizontal fracture intensities. The fracture density distributions provide a valuable database for further numerical and statistical analysis. This allows assessment in terms of water inflow into the excavation. A comprehensive image analysis was undertaken on several extraction models. Results indicate that extraction thickness has a significant effect on the fracture pattern and the fracture density distributions. The results can be used to adapt model findings to situations with a range of extraction thicknesses. The technique has allowed improvement in image enhancement and in the interpretation of model results. In particular, a qualitative comparison between different models is possible.

Jan 12, 1992

By Haldane J. S.

Discussion of a paper presented at the Institution of Mining Engineers' general meeting held in London on 8th June 1916 included oral contributions by Louis H., Mowat D.M., Lupton A., Bailey T.H., Blackett W.C. and Gerrard J., and written contributions by Collis E.L., Carlow C. and Wilson W.B., with the author's oral and brief written responses

Dec 1, 1916